LTC2163IUK - 16-Bit 80Msps Low Power ADC | Analog Devices
Référence : LTC2163IUK ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $70.48 | $70,48 |
| 10 | $63.43 | $634,30 |
| 100 | $56.38 | $5 638,00 |
| 500 | $49.34 | $24 670,00 |
| 1 000 | $42.29 | $42 290,00 |
LTC2163IUK Présentation
What is a pipelined ADC? A pipelined analog-to-digital converter is a high-speed sampling architecture that breaks the conversion process into multiple low-resolution stages. Each stage samples and converts a coarse portion of the input, then passes a residue to the next stage. Pipelined ADCs are the dominant architecture for 8-bit to 16-bit sampling at 20 Msps to 500 Msps, sitting within the broader hierarchy of ADC -> data converter -> mixed-signal IC -> semiconductor. They are favored when both speed and resolution matter, as in communications, instrumentation, and imaging.
Key features of the LTC2163IUK include selectable CMOS, LVDS, or DDR LVDS parallel interfaces, a 1.8 V analog supply, an optional low-noise bypass mode, and 1.4 W typical power dissipation at 80 Msps. Differential input drive with an internal reference simplifies front-end design, while the exposed pad provides a low thermal-resistance path (around 28 C/W theta_JA) for reliable operation at full sampling rate.
The device operates from a single 1.8 V supply, with separate analog and digital supply pins to minimize coupling noise. Its pipelined core stages are calibrated at power-up using an internal state-machine routine. Digital output data is presented on 16 parallel lanes, configurable for CMOS single-data-rate or LVDS double-data-rate modes. Typical SNR of 76.8 dB and SFDR of 90 dB at 70 MHz input make it well-suited for software-defined radio and cellular base-station digitizers.
Typical applications include software-defined radio, cellular base-station receivers, IF sampling for communications systems, medical imaging front ends, and industrial ultrasound signal chains. The wide input bandwidth and low jitter support undersampling architectures that reduce system BOM.
When designing with the LTC2163IUK, ensure the analog input common-mode voltage is set correctly (typically 0.9 V internal) and use a low-jitter clock driver. Provide a solid ground plane under the exposed pad, stitching vias around the perimeter, and decouple each supply pin with a 0.1 uF ceramic plus a 10 uF bulk capacitor within 2 mm of the pin.
This page synthesizes distributor pricing, drop-in same-package alternatives, application companion MPNs, and PCB layout guidance not aggregated on the manufacturer datasheet or typical distributor pages.
Alternatives de remplacement direct pour LTC2163IUK — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LTC2163IUK (même facteur de forme et même empreinte) — différant par Package, Operating Temperature Range, SNR, Resolution, Input Type.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
LTC2163CUK#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2164IUK#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2165IUK#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2145CUP-12
✅ Remplacement direct✓ En stock
$26.4 / unité
Voir la fiche technique →LTC2156IUP-14
✅ Remplacement direct✓ En stock
$134.1 / unité
Voir la fiche technique →LTC2174IUKG-14
✅ Remplacement direct✓ En stock
$119.96 / unité
Voir la fiche technique →LTC2192CUKG#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2163IUK Valeurs maximales et caractéristiques électriques
| Résolution | 16 bits |
| Sample Rate | 80 Msps |
| Number of Inputs | 1 |
| Architecture | Pipelined |
| Boîtier | 48-QFN (7x7 mm) with exposed pad |
| SNR | 76.8 dB |
| SFDR | 90 dB |
| Aperture Jitter | 0.07 ps RMS |
| Analog Supply Voltage | 1.8 V |
| Digital Supply Voltage | 1.8 V |
| Power Dissipation (typ) | 1.4 W at 80 Msps |
| Output Interface | Parallel CMOS / DDR LVDS / LVDS (selectable) |
| Input Type | Differential |
| Operating Temperature Range (I grade) | -40C to +85C |
| Thermal Resistance (theta_JA) | 28 C/W (typical with exposed pad) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (PBF suffix) |
Configuration des broches de LTC2163IUK
| Broche 1 | GND — Ground (exposed pad also connects here) |
| Broche 2 | AIN+ — Differential analog input, positive |
| Broche 3 | AIN- — Differential analog input, negative |
| Broche 4 | VCM — Common-mode voltage output (0.9 V typical) |
| Broche 5 | REFT — Top reference decoupling |
| Broche 6 | REFB — Bottom reference decoupling |
| Broche 7 | AVDD — 1.8 V analog supply |
| Broche 8 | GND — Ground |
| Broche 9 | CLK+ — Differential clock input, positive |
| Broche 10 | CLK- — Differential clock input, negative |
| Broche 11 | GND — Ground |
| Broche 12 | OGND — Output driver ground |
| Broche 13 | OVDD — 1.8 V output driver supply |
| Broche 14 | D15 — Parallel data output D15 (MSB) |
| Broche 15 | D14 — Parallel data output D14 |
| Broche 16 | D13 — Parallel data output D13 |
| Broche 17 | D12 — Parallel data output D12 |
| Broche 18 | D11 — Parallel data output D11 |
| Broche 19 | D10 — Parallel data output D10 |
| Broche 20 | D9 — Parallel data output D9 |
| Broche 21 | D8 — Parallel data output D8 |
| Broche 22 | D7 — Parallel data output D7 |
| Broche 23 | D6 — Parallel data output D6 |
| Broche 24 | D5 — Parallel data output D5 |
| Broche 25 | D4 — Parallel data output D4 |
| Broche 26 | D3 — Parallel data output D3 |
| Broche 27 | D2 — Parallel data output D2 |
| Broche 28 | D1 — Parallel data output D1 |
| Broche 29 | D0 — Parallel data output D0 (LSB) |
| Broche 30 | OGND — Output driver ground |
| Broche 31 | OVDD — 1.8 V output driver supply |
| Broche 32 | OGND — Output driver ground |
| Broche 33 | DRVDD — 1.8 V digital supply |
| Broche 34 | DRGND — Digital ground |
| Broche 35 | MODE — Output mode select (CMOS/LVDS/DDR LVDS) |
| Broche 36 | OF — Output format select |
| Broche 37 | RAND — Randomizer enable |
| Broche 38 | CS — Chip select (SPI configuration) |
| Broche 39 | SCK — Serial clock (SPI configuration) |
| Broche 40 | SDI — Serial data in (SPI configuration) |
| Broche 41 | SDO — Serial data out (SPI configuration) |
| Broche 42 | RESET — Hardware reset (active low) |
| Broche 43 | PD — Power-down control |
| Broche 44 | NC — Not connected (per datasheet) |
| Broche 45 | AVDD — 1.8 V analog supply |
| Broche 46 | GND — Ground |
| Broche 47 | REFT — Top reference decoupling |
| Broche 48 | REFB — Bottom reference decoupling |
Courbe de déclassement en puissance du LTC2163IUK
Courbe de déclassement en puissance du LTC2163IUK
Applications typiques
LTC2163IUK convient pour 7 applications: Software-Defined Radio (SDR) Front End, Cellular Base Station Receiver, Medical Ultrasound Imaging, Industrial Test and Measurement Instrumentation, Radar and Lidar Signal Processing, Spectrum Analyzer and Digital Downconverter, High-Speed Data Acquisition Systems.
Software-Defined Radio (SDR) Front End
The LTC2163IUK is well-matched to software-defined radio receivers where 80 Msps sampling supports undersampling of IF signals up to several hundred MHz. The 0.07 ps RMS aperture jitter preserves SNR at high input frequencies - critical for SDR front-end performance where clock jitter directly limits achievable SNR. Its 76.8 dB SNR and 90 dB SFDR provide dynamic range sufficient for high-order QAM demodulation (64-QAM, 256-QAM). Place the ADC between the final IF mixer and the FPGA signal-processing chain, with a low-jitter differential clock from a dedicated clock-cleaning PLL. Unlike a slower 25 Msps converter, the LTC2163IUK captures wider instantaneous bandwidth, reducing the number of IF downconversion stages.
Recommandé
Cellular Base Station Receiver
In LTE and 5G NR base-station receivers, the LTC2163IUK digitizes intermediate-frequency signals from the antenna front-end chain. Its 80 Msps rate handles multi-carrier LTE signals with adequate margin, while 76.8 dB SNR supports the error-vector-magnitude (EVM) budgets required for 256-QAM modulation in dense urban deployments. The exposed-pad QFN package enables dense PCB layouts typical of multi-antenna MIMO receivers. Position the ADC directly after the final downconversion stage, with the digital outputs routed as matched-length differential pairs to the baseband ASIC. Compared to discrete mixer+filter+IF-ADC designs, an LTC2163IUK-based direct-IF architecture eliminates analog filtering stages.
Recommandé
Medical Ultrasound Imaging
Medical ultrasound imaging systems require high-dynamic-range digitization of echo returns, and the LTC2163IUK delivers 76.8 dB SNR with 90 dB SFDR needed to resolve deep-tissue structures. The 80 Msps sample rate handles transducer center frequencies up to 30 MHz with adequate Nyquist margin, while the low 1.4 W power dissipation keeps thermal load manageable in portable cart-based systems. Place the ADC at the output of the time-gain-compensation (TGC) amplifier chain, with the digital outputs routed to the beamforming FPGA. Unlike continuous-wave Doppler systems that can use slower converters, pulsed-wave imaging benefits from the LTC2163IUK's wide instantaneous bandwidth to capture broadband transducer responses.
Recommandé
Industrial Test and Measurement Instrumentation
Test instruments such as digital oscilloscopes, spectrum analyzers, and signal analyzers benefit from the LTC2163IUK's combination of 16-bit resolution and 80 Msps sampling. The high SFDR of 90 dB enables clean spectrum measurements without spurious artifacts masking low-level harmonics, while the differential inputs simplify direct interface to active probes. In a digitizer subsystem, pair the LTC2163IUK with an FPGA-based DSP pipeline that performs windowing, FFT, and trigger logic. Compared to 8/10/12-bit oscilloscope-ADCs, the 16-bit LTC2163IUK offers 4-8x more vertical resolution for precise amplitude measurements on low-level signals.
Recommandé
Radar and Lidar Signal Processing
In phased-array radar and lidar receivers, the LTC2163IUK samples wideband IF signals carrying range-Doppler information. The 80 Msps rate supports radar pulse bandwidths up to 40 MHz for sub-meter range resolution, while the 0.07 ps jitter floor maintains phase coherence across receive channels - essential for digital beamforming. The 48-QFN package fits easily into multi-channel receiver modules. Connect the ADC between the downconversion mixer and the FPGA-based beamforming signal-processing array. For automotive radar at 77 GHz, an external downconversion to IF followed by the LTC2163IUK provides cost-effective digitization versus millimeter-wave direct-sampling ADCs.
Recommandé
Spectrum Analyzer and Digital Downconverter
Wideband spectrum analyzers and digital-downconverter (DDC) systems leverage the LTC2163IUK's wide input bandwidth and 16-bit resolution to capture large RF bandwidths before digital channelization. The 80 Msps rate enables processing of signals up to 40 MHz in real time, with downstream FPGA DDC chains extracting multiple narrowband channels from the wideband ADC data. The selectable CMOS/LVDS/DDR-LVDS output modes simplify interface to different FPGA families. Place the LTC2163IUK between the final RF mixer and the FPGA, and use its low-jitter clock input to drive both the mixer LO and the ADC sampling clock from a common PLL for coherent demodulation.
Recommandé
High-Speed Data Acquisition Systems
Multi-channel data acquisition (DAQ) systems for vibration analysis, acoustic measurement, and industrial condition monitoring deploy the LTC2163IUK to digitize signals from accelerometers, microphones, and piezoelectric sensors. Each channel's 76.8 dB SNR provides 12+ ENOB of effective resolution, sufficient for resolving sensor noise floors. Synchronize multiple LTC2163IUK devices by sharing a common low-jitter clock across the array - the 0.07 ps aperture jitter ensures channel-to-channel phase coherence. Place the ADC on a dedicated analog island of the PCB with separate analog/digital ground planes stitched together only at the ADC exposed pad.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LTC2163IUK — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LTC2163CUK#PBF | LTC2164IUK#PBF | LTC2165IUK#PBF | LTC2156IUP-14 | LTC2174IUKG-14 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same |
| Resolution | 16 bits | 16 bits | 16 bits | 16 bits | 14 bits | 14 bits |
| Sample Rate | 80 Msps | 80 Msps | 105 Msps | 125 Msps | 80 Msps | 105 Msps |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Operating Temperature (I grade) | -40C to +85C | 0C to +70C (C grade) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Principaux différenciateurs
- Industrial temperature range without cost penalty (vs LTC2163CUK#PBF)
- Higher bandwidth headroom for IF undersampling (vs LTC2164IUK#PBF)
- Higher SFDR than competing 14-bit alternatives (vs LTC2156IUP-14)
Notes de conception
Solder the exposed pad of the 48-QFN package to a continuous ground plane with at least 9 thermal vias (3x3 array, 0.3 mm drill) connecting top-side ground to internal ground layers. Stitching vias should be placed on a 1 mm pitch around the package perimeter. Per Analog Devices application guidance for the LTC2163 family, this stitching reduces theta_JA to approximately 28 C/W and minimizes digital switching noise coupling into the analog input network. Estimated thermal calculation: at 1.4 W power dissipation with theta_JA = 28 C/W, junction temperature rises 39 C above ambient (TJ = TA + 39 C), giving TJ = 124 C at TA = 85 C maximum.
Separate analog and digital ground planes should be partitioned under the ADC, with a single join point directly under the device exposed pad. Place the 0.1 uF ceramic decoupling capacitors within 2 mm of each AVDD, OVDD, and DRVDD pin, and add 10 uF bulk capacitors on each supply rail. The CLK+/CLK- differential clock traces should be routed as a 100 ohm differential pair with matched length (delta < 1 mm) and isolated from digital output switching signals by ground fills. Differential input traces AIN+/AIN- should likewise be routed as a matched-length 100 ohm differential pair to the input driver.
Use a low-jitter clock driver (such as the AD9510 or ADF4360) with the LTC2163IUK, as the SNR is directly limited by aperture jitter at high input frequencies. SNR_jitter = 20*log10(1/(2*pi*fin*jitter)); with 0.07 ps jitter, SNR is preserved up to the Nyquist limit. For differential clock drive, AC-couple the CLK+/CLK- inputs with 0.1 uF capacitors and bias through 50 ohm termination resistors to 0.9 V common-mode voltage. Maintain clock signal integrity by routing on an inner PCB layer with continuous ground plane underneath.
Estimated power supply design: The 1.8 V AVDD rail should source up to 600 mA (approximately 1.1 W analog power). Use an LDO such as the ADP7104 to generate AVDD from a 3.3 V rail, providing low-noise analog supply. The DRVDD and OVDD rails can share a separate LDO for digital isolation. Per the Analog Devices datasheet, total power at 80 Msps with LVDS output is approximately 1.4 W; at CMOS output, expect 1.5 W due to higher digital switching current.
Do not allow the analog input common-mode voltage to drift outside the 0.7 V to 1.1 V range - use a transformer or driver amplifier (ADA4937/ADA4932) to maintain proper DC bias at AIN+/AIN-. Avoid routing digital output traces (D0-D15) across the analog input area; this couples switching noise into the sensitive front-end. Ensure MODE and OF pins are tied to known logic levels at power-up to select the correct output mode. Finally, do not exceed the 1.98 V absolute maximum on any supply pin, and provide proper sequencing (AVDD before DRVDD/OVDD) to avoid latch-up.
Informations de conformité
RoHS and REACH compliant per #PBF suffix designation. No AEC-Q100 automotive grade exists in the LTC2163 family per the Analog Devices product page - contact ADI for automotive-grade alternatives. Lead-free plating per JEDEC J-STD-020 reflow profiles.