MAX202ECSE+G068 - 2/2 RS-232 Transceiver | Analog Devices
Référence : MAX202ECSE+G068 ✓ ActifMAX202ECSE+G068 Présentation
An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. This dual-transceiver, dual-receiver arrangement belongs to the broader line-driver and receiver hierarchy, where interface ICs connect modern digital equipment to established serial-bus systems. Charge-pump circuitry allows the MAX202 family to generate the positive and negative voltage levels required by RS-232 without an external negative supply.
The MAX202ECSE+G068 provides 2 transmitter outputs and 2 receiver inputs for compact bidirectional serial links. Its operating supply range of 4.5 V to 5.5 V supports conventional 5 V equipment. The listed 15 kV ESD protection rating is a key feature for ports connected to external cables, where electrostatic discharge can reach the transceiver through unprotected connector paths. The 16-pin SOIC package is offered in tube packaging according to the manufacturer ordering information.
The interface architecture is intended for point-to-point RS-232 and V.28 communications in equipment that requires multiple serial channels. Because RS-232 uses unbalanced signaling with defined logic thresholds, the transmitter converts host-side logic into valid line voltages, while the receiver converts the line voltage into a host-readable logic state. The integrated charge-pump support reduces external circuitry compared with solutions requiring a separate negative rail or discrete level-shifting networks.
Typical applications include industrial serial-control panels, point-of-sale equipment, instrumentation links, data-acquisition systems, and communications equipment that needs more than one RS-232 port. In those systems, the device separates low-voltage controller signals from cable-side RS-232 levels while limiting the number of external level-conversion components. Its compact 16-pin SOIC footprint also supports PCB layouts where connector-side routing space is limited.
For a robust design, route the external serial connector through the shortest practical path to the transceiver, maintain the device's specified supply and decoupling requirements, and use the pin-description table in the Analog Devices datasheet when assigning PCB tracks. Cable-side protection and chassis-ground strategy should be selected according to the installation environment, especially when exposed to industrial transients.
This page organizes the MAX202ECSE+G068 interface details, sourcing information, same-footprint alternatives, comparison parameters, and application-oriented engineering guidance into a practical selection reference for engineers designing 5 V RS-232 equipment.
Alternatives de remplacement direct pour MAX202ECSE+G068 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX202ECSE+G068 (même facteur de forme et même empreinte) — différant par Package, Transceiver Configuration, ESD Protection, Supported Protocol.
MAX202ECSE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX202ECSE+TG068
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX202ECSE+T
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX202ECSE+G068 Spécifications
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Transceiver Configuration | 2/2 full-duplex RS-232 transceiver |
| Supported Protocol | RS-232 and V.28 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| ESD Protection | 15 kV |
| Boîtier | 16-pin SOIC, 0.154 inch body width, 3.90 mm body width |
| Package Type | SOIC-16 |
| Type de montage | Surface mount |
| Manufacturer Packaging | Tube |
| Nombre de broches | 16 |
| Interface Category | RS-232, RS-422 and RS-485 interface device family listing |
| Transmitter Outputs | 2 |
| Receiver Inputs | 2 |
| Charge-Pump Support | Integrated for RS-232 level generation |
Guide de configuration des broches du MAX202ECSE+G068 soic-16
Configuration des broches du MAX202ECSE+G068 (boîtier soic-16). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX202ECSE+G068.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX202ECSE+G068 convient pour 6 applications: Industrial Serial Control Panels, Point-of-Sale Terminal Interfaces, Data-Acquisition Instruments, Security and Access-Control Equipment, Communication and Network Equipment, Test and Measurement Systems.
Industrial Serial Control Panels
The MAX202ECSE+G068 suits industrial control panels that need two RS-232 paths between a controller and external equipment. Its 2/2 configuration supports two transmitters and two receivers, while the 4.5 V to 5.5 V supply range integrates with conventional 5 V control electronics. The listed 15 kV ESD protection improves robustness at connector-facing circuits exposed to electrostatic discharge. Install the transceiver near the serial connector, keep the cable-side traces short, and provide local supply decoupling. The device implements RS-232 and V.28 signaling, making it appropriate for configuration ports, service interfaces, and supervisory links where longer-distance point-to-point communication is required.
Recommandé
Point-of-Sale Terminal Interfaces
The MAX202ECSE+G068 can connect a point-of-sale terminal or peripheral controller to two RS-232 ports without requiring a separate negative supply rail. Its two transmitters and two receivers support compact multi-port serial equipment, while the 5 V supply range aligns with common embedded logic systems. The 16-pin SOIC package reduces board area compared with larger discrete interface arrangements. Position the transceiver near the connector to minimize exposed cable-side routing, and confirm the manufacturer pin assignments before laying out the PCB. The E-series ESD protection is particularly relevant at user-accessible peripheral ports, although it does not replace correctly selected external surge and cable protection.
Recommandé
Data-Acquisition Instruments
The MAX202ECSE+G068 is appropriate for laboratory and industrial data-acquisition instruments that exchange commands and results through RS-232. Its 2/2 transceiver arrangement can handle separate control and measurement channels, and the 4.5 V to 5.5 V supply range supports a 5 V instrument architecture. Integrating the transceiver near the DB9 or equivalent connector helps keep the cable interface compact. For bench equipment, pay particular attention to grounding, cable length, and receiver behavior. The manufacturer documentation identifies the part for RS-232 and V.28 communication, allowing it to bridge modern TTL logic with established instrumentation-control ports.
Recommandé
Security and Access-Control Equipment
The MAX202ECSE+G068 can support serial programming and diagnostic ports in access-control and security equipment. Two RS-232 channels provide flexibility for connecting a reader, controller, or service interface while the 15 kV ESD protection helps manage electrostatic discharge reaching connector-facing electronics. Use the transceiver near the connector and observe the manufacturer’s supply and grounding guidance. Because security devices may also carry sensitive data, the serial interface should not be treated as a security boundary by itself; authentication and encryption belong at a higher protocol layer. The 16-pin SOIC package provides a compact implementation in space-constrained reader and controller assemblies.
Recommandé
Communication and Network Equipment
The MAX202ECSE+G068 is useful in communication equipment that retains RS-232 service, console, or management ports alongside newer digital interfaces. Its 2/2 configuration permits two independent serial paths, and the single 5 V supply range simplifies integration with embedded processors and programmable logic. The ESD-protected E-series implementation is advantageous when serial connectors are exposed to maintenance personnel or cable-borne electrostatic discharge. Route the interface toward the connector without long stubs, maintain continuous ground references, and follow the datasheet layout guidance. For networked equipment, the MAX202 handles only the physical RS-232 layer, so the connected system must implement the required protocol and security behavior.
Recommandé
Test and Measurement Systems
The MAX202ECSE+G068 can serve as the RS-232 interface in test equipment, programmable instruments, and laboratory controllers. The 2 transmitters and 2 receivers support command and response channels, while the 4.5 V to 5.5 V supply range works with 5 V measurement platforms. Its 16-pin SOIC footprint allows placement close to the external connector, reducing the area occupied by cable-side routing. For accurate measurements, maintain a consistent signal-reference ground and use shielded cable where required by the installation. Review the Analog Devices pin table and electrical characteristics for the exact ordering code before finalizing the schematic and PCB.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX202ECSE+G068 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX202ECSE+ | MAX202ECSE+TG068 | MAX202ECSE+T |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same |
| Number of Drivers/Receivers | 2/2 | 2/2 | 2/2 | 2/2 |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Protocol | RS-232 and V.28 | RS-232 and V.28 | RS-232 and V.28 | RS-232 and V.28 |
| ESD Protection | 15 kV | 15 kV | 15 kV | 15 kV |
Principaux différenciateurs
- Two transmitters and two receivers in one 16-pin SOIC (vs MAX202ECSE+)
- Single 5 V supply operation (vs MAX202ECSE+TG068)
- 15 kV ESD-protected E-series interface (vs MAX202ECSE+T)
Notes de conception
Place the MAX202ECSE+G068 close to the external serial connector and route the receiver and transmitter paths directly to their respective pins. Keep the 16-pin SOIC footprint free of copper keepouts or tooling conflicts, and use the manufacturer pin-description table to confirm pin 1 orientation. The connector-side ground and signal paths should have a continuous reference plane to minimize noise pickup and ESD-current loops.
Operate the device from a stable 4.5 V to 5.5 V supply, with local high-frequency bypass placed close to the supply pins. Do not assume that the integrated charge pump eliminates all supply-transient requirements; ringing, inadequate source impedance, or an undersized local capacitor can affect transmitter and receiver operation. Follow the capacitor values and layout guidance in the Analog Devices datasheet for the selected configuration.
A shared 16-pin SOIC outline does not by itself prove that another MAX202 ordering code is interchangeable. Before substituting a candidate, compare ENABLE or shutdown polarity, receiver-control pins, temperature grade, ESD level, and package suffix. Also verify the external charge-pump capacitor connections in the schematic and PCB layout; incorrect capacitor values or placement can prevent reliable RS-232 voltage generation.
Keep the RS-232 cable interface physically separated from sensitive analog and high-speed digital paths, and route it away from switching-node areas. Use a continuous ground reference and controlled connector return path to reduce common-mode noise. For industrial installations, evaluate whether additional connector-side surge protection, isolation, or filtering is required beyond the device’s stated 15 kV ESD protection.
Informations de conformité
The E-series family is listed with 15 kV ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements for the exact MAX202ECSE+G068 ordering code were not identified.