MAX232BAWE+ - 2/2 RS-232 Transceiver, 200 kbps | Analog Devices
Référence : MAX232BAWE+ ✗ Fin de vieMAX232BAWE+ Présentation
An RS-232 transceiver is an interface IC that bridges the voltage domains used by TTL/CMOS logic and RS-232 serial communications. The MAX232 family integrates charge-pump circuitry, drivers, and receivers into one package. This integration eliminates a separate RS-232 level-shifting circuit and places the complete signal-conditioning path close to the host logic. Within the product hierarchy, the MAX232 is an RS-232 transceiver, an interface IC, and a semiconductor.
The principal operating characteristics include two driver channels, two receiver channels, full-duplex capability, 200 kbps signaling, and 500 mV receiver hysteresis. The 500 mV hysteresis helps reject small noise disturbances around the receiver threshold. Its 4.5 V to 5.5 V supply range provides compatibility with conventional +5 V digital systems, while the integrated charge-pump circuitry develops the positive and negative voltage levels required by RS-232 drivers.
This MAX232BAWE+ device uses the 16-pin small-outline integrated-circuit package identified as 16-SOIC in the product information. Its 2/2 driver-receiver organization permits two logical serial channels per device. The 200 kbps maximum data rate is suitable for many legacy control and diagnostic ports, but it does not target high-speed differential serial protocols. Use a newer multi-protocol interface when rates substantially above 200 kbps, lower supply voltage, or smaller package area are required.
Typical uses include industrial serial adapters, laboratory instruments, embedded-control boards, barcode-scanner interfaces, and service equipment that retains an RS-232 port. In these systems, the MAX232BAWE+ can connect a microcontroller UART to a DB9 or other RS-232 connector. Designers must still account for cable length, grounding, protection, and the unidirectional nature of each RS-232 driver channel.
For layout, place the device close to the connector or protected interface boundary and route each RS-232 line away from sensitive clock and analog signals. Follow the manufacturer datasheet for the charge-pump capacitor connections, supply bypass capacitor, and unused-channel handling. Confirm the full logic-level and channel direction before assigning pins in a new PCB or converting an existing design.
This product reference combines the exact MAX232BAWE+ ordering information with practical RS-232 interface guidance, drop-in family comparisons, and engineering-focused design notes. It is intended to help engineers identify the correct package, operating limits, and replacement path without overlooking the distinctions between electrically similar MAX232 variants.
Alternatives de remplacement direct pour MAX232BAWE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX232BAWE+ (même facteur de forme et même empreinte) — différant par Package, Product Type, Interface Standard, Technology, Transceiver Configuration.
MAX232AWE+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX232EWE+
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MAX232CSE+
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MAX232AESE+
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MAX232ACSE+T
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX232BAWE+ Spécifications
| Product Type | RS-232 transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| Maximum Data Rate | 200 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Receiver Hysteresis | 500 mV |
| Plage de température de fonctionnement | 0°C to +70°C |
| Boîtier | 16-pin SOIC |
| Package Family | SOIC family |
| Type de montage | Surface mount |
| Interface Standard | RS-232 |
| Supply Type | +5 V |
| Automotive Qualification | Not applicable |
Guide de configuration des broches du MAX232BAWE+ soic family
Configuration des broches du MAX232BAWE+ (boîtier soic family). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX232BAWE+.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX232BAWE+ convient pour 6 applications: Industrial Serial Adapter, Laboratory Instrument Interface, Embedded Controller Communication, Barcode Scanner Interface, Test and Measurement Control Port, Legacy Service Equipment.
Industrial Serial Adapter
The MAX232BAWE+ fits an industrial serial adapter because it combines two RS-232 drivers, two receivers, and a 200 kbps data rate in one 16-SOIC package. It can connect two UART channels from a controller to protected RS-232 connector circuits without a separate level-shifting assembly. The integrated charge-pump function produces the bipolar voltage levels required by RS-232 drivers, while the 4.5 V to 5.5 V supply range matches conventional +5 V control electronics. Its listed 0°C to +70°C range makes it appropriate for indoor equipment managed within that thermal envelope. Designers should verify the exact data-sheet pinout and unused-channel recommendations before layout.
Recommandé
Laboratory Instrument Interface
The MAX232BAWE+ is appropriate for laboratory instruments that retain a legacy RS-232 port while using modern TTL logic internally. Two driver channels and two receiver channels support full-duplex serial communication, and the 200 kbps rate is well suited to command consoles, calibration equipment, and laboratory data acquisition controls. Because the MAX232BAWE+ operates from 4.5 V to 5.5 V, it integrates readily with +5 V digital logic, while its integrated charge pumps eliminate a discrete bipolar driver circuit. The 16-SOIC package simplifies board replacement in legacy instruments. For settings with broader ambient temperature, transients, or isolation requirements, select a suitably qualified interface and add appropriate connector protection.
Recommandé
Embedded Controller Communication
The MAX232BAWE+ can bridge a microcontroller UART to an RS-232 port in embedded-control equipment. A 200 kbps maximum rate supports command traffic, status reporting, firmware update links, and configuration protocols commonly used in legacy controllers, while the 2/2 channel organization can serve separate transmit and receive paths. The device requires only a +5 V supply in the 4.5 V to 5.5 V range and places the voltage-conversion function in a compact 16-SOIC package. Layout should keep the transceiver near the protected connector boundary and route noisy RS-232 traces away from precision analog circuitry. The MAX232 converts signal levels but does not provide galvanic isolation, surge protection, or automatic transceiver direction control.
Recommandé
Barcode Scanner Interface
The MAX232BAWE+ suits barcode scanners and other point-of-sale peripherals that communicate through RS-232. The 200 kbps data rate exceeds the throughput normally needed for short scanner packets, and the integrated two-channel driver/receiver arrangement supports bidirectional command and acknowledgment traffic. Its +5 V supply operation and 16-SOIC footprint are convenient for established equipment layouts. Place the interface close to the external connector and include suitable transient protection because retail equipment may be exposed to cables that are longer than the logic board. The listed 0°C to +70°C operating range suits controlled indoor installations, but the complete enclosure temperature—not only the PCB temperature—must remain within the device limits.
Recommandé
Test and Measurement Control Port
The MAX232BAWE+ is useful for test and measurement equipment that exposes an RS-232 control interface alongside TTL-based logic. The two receivers allow incoming commands or status signals, while the two drivers provide outbound serial data, supporting full-duplex operation at rates up to 200 kbps. Since the device operates from 4.5 V to 5.5 V, it can be used with conventional +5 V instrument electronics, and its integrated charge-pump design reduces external component count. The 16-SOIC package is appropriate for repair boards that follow the original MAX232 footprint. Engineers should preserve adequate separation between RS-232 routing and sensitive measurement circuitry and should not treat the MAX232 as a substitute for galvanic isolation in hazardous or ground-potential-sensitive test systems.
Recommandé
Legacy Service Equipment
The MAX232BAWE+ is a practical choice for repairing or extending legacy service equipment with an RS-232 service port. Two transmit and two receive channels reproduce the familiar MAX232 interface in a 16-SOIC footprint, and the 200 kbps limit is suitable for diagnostic commands, configuration dumps, and short status packets. Its 4.5 V to 5.5 V operating range matches the +5 V logic often retained in older instruments. When replacing an installed device, verify the package lead geometry, pin numbering, charge-pump capacitor values, and unused-pin connections against the manufacturer data sheet. Connector-side ESD or surge protection may need to be added separately, particularly for field-service equipment connected to long cables.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX232BAWE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX232AWE+ | MAX232EWE+ | MAX232CSE+ | MAX232AESE+ | MAX232ACSE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Interface Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
Principaux différenciateurs
- Exact obsolete ordering identity (vs MAX232ACSE+)
- Two full-duplex channels in one package (vs MAX232CSE+)
- Established 200 kbps RS-232 performance (vs MAX232EWE+)
Notes de conception
Place the MAX232BAWE+ close to the RS-232 connector or protected interface boundary, and route the RS-232 lines as a compact group away from sensitive analog inputs, oscillators, and high-speed clocks. Keep the charge-pump capacitor connections short and place the supply bypass capacitor close to the device. Use the manufacturer data-sheet pin description to assign logic and RS-232 signals; because the exact pin list is not published in the product excerpts, verify every connection before routing a replacement board.
Do not assume that every similarly named MAX232 ordering code is an unrestricted substitute. Compare the 16-SOIC footprint, lead geometry, pin numbering, two-driver and two-receiver organization, +5 V supply range, 200 kbps data rate, receiver hysteresis, and required temperature grade. Check whether the replacement is a commercial-, industrial-, or automotive-grade orderable configuration. Confirm that the manufacturer data sheet permits the intended unused-channel connections before using a family variant as a drop-in replacement.
RS-232 drivers intentionally produce bipolar transitions, so connector cables can introduce both radiated noise and incoming transients. Keep the transceiver close to the connector-side protection network, maintain a continuous ground reference, and avoid routing RS-232 conductors parallel to sensitive signal paths for long distances. The MAX232BAWE+ performs level conversion, but it does not provide galvanic isolation, surge protection, or unlimited fault tolerance. Add appropriately rated protection and isolation when the connected equipment is exposed to outdoor cables or large ground-potential differences.
Informations de conformité
The exact MAX232BAWE+ product listing identifies the device as obsolete but does not state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Those fields remain unknown rather than being inferred from the MAX232 family name.