MAX232ECDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments
Référence : MAX232ECDWRE4 ✓ ActifMAX232ECDWRE4 Présentation
An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential, bipolar RS-232 signals. It belongs to the serial-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → communication semiconductor. This conversion allows equipment with a logic-level UART to connect to computers, industrial controllers, test equipment, and other RS-232 endpoints through a protected physical interface.
The MAX232ECDWRE4 combines two RS-232 drivers, two receivers, and the charge-pump voltage generator in one package. All RS-232 pins feature 15 kV HBM and 15 kV IEC 61000-4-2 air-gap discharge protection, while RS-232 pins also provide 8 kV IEC 61000-4-2 contact-discharge protection. These ratings make the device appropriate for exposed serial ports where electrostatic discharge is a practical concern.
The charge-pump architecture creates positive and negative RS-232 levels without a negative supply rail. Its four external charge-pump capacitors determine the required energy-transfer behavior and must be placed close to their associated pins. The receiver converts incoming TIA/EIA-232-F signals into 5 V TTL/CMOS levels, while the drivers convert TTL/CMOS inputs into compliant RS-232 output levels. The MAX232E family is optimized for operation from a single +5 V supply.
Typical uses include legacy industrial serial consoles, programmable test equipment, point-of-sale peripherals, data acquisition systems, and service interfaces embedded in larger control systems. The 250 kbps maximum data rate supports moderate-speed asynchronous links rather than high-bandwidth differential serial protocols. Full-duplex operation allows a port to transmit and receive simultaneously through independent channels.
PCB design should prioritize short traces from the charge-pump capacitors to pins 1 and 4, as specified by the Texas Instruments MAX232E datasheet. Keep the interface connector and transceiver pins away from sensitive analog or high-speed digital nodes, and route the ground return with the RS-232 signal path to reduce noise pickup. A common-mode choke can be added when cable emissions or susceptibility become significant.
This page combines the manufacturer interface specifications, protection ratings, package details, verified sourcing information, drop-in alternatives, and practical layout guidance in one engineering-focused reference for evaluating the MAX232ECDWRE4 in +5 V RS-232 designs.
Alternatives de remplacement direct pour MAX232ECDWRE4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX232ECDWRE4 (même facteur de forme et même empreinte) — différant par Number of Receivers, Number of Drivers, Package, Product Type.
MAX232ECDWRG4
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX232ECDWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX232ECDWRE4 Spécifications
| Product Type | Dual RS-232 driver and receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Operating Mode | Full duplex |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 250 kbps |
| Interface Standard | TIA/EIA-232-F |
| Logic-Level Interface | 5 V TTL/CMOS |
| Charge-Pump Capacitors | 4 external capacitors |
| HBM ESD Protection | 15 kV on all RS-232 pins |
| IEC 61000-4-2 Air-Gap ESD Protection | 15 kV on all RS-232 pins |
| IEC 61000-4-2 Contact Discharge Protection | 8 kV on RS-232 pins |
| Boîtier | 16-SOIC, 7.50 mm width |
| Terminal Count | 16 terminals |
| Terminal Form | Gull wing |
| Type de montage | Surface mount |
| Temperature Grade | Commercial |
Guide de configuration des broches du MAX232ECDWRE4 16-soic, 7.50 mm width
Configuration des broches du MAX232ECDWRE4 (boîtier 16-soic, 7.50 mm width). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX232ECDWRE4.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX232ECDWRE4 convient pour 6 applications: Industrial Equipment Serial Console, Programmable Test Equipment Control, Point-of-Sale Terminal Interface, Data Acquisition System Communication, Embedded Service and Diagnostics Port, Legacy Computer Serial Peripheral.
Industrial Equipment Serial Console
The MAX232ECDWRE4 fits legacy industrial controllers and service equipment that expose a +5 V UART through an RS-232 connector. Its two driver and two receiver channels support full-duplex communication at up to 250 kbps, while the integrated charge-pump generator eliminates the need for a negative supply rail. The 15 kV IEC 61000-4-2 air-gap and 8 kV contact-discharge ratings add valuable protection for a connector that may be accessible during maintenance. Place the four charge-pump capacitors close to pins 1 and 4, route the cable ground with the signal path, and keep the connector interface away from precision analog circuitry.
Recommandé
Programmable Test Equipment Control
The MAX232ECDWRE4 is useful in laboratory instruments that retain a host computer or controller interface for configuration, diagnostics, and firmware loading. A 250 kbps RS-232 link is appropriate for command traffic, and the device translates the controller's TTL/CMOS UART signals to and from TIA/EIA-232-F levels. Its dual-channel architecture permits simultaneous command transmission and status reception. The single 5 V supply simplifies isolation and power planning, while the enhanced RS-232-pin discharge ratings improve robustness when the instrument is connected to user-accessible equipment. Use a dedicated protection ground and maintain short charge-pump capacitor traces to prevent switching transients from disturbing precision measurement circuits.
Recommandé
Point-of-Sale Terminal Interface
The MAX232ECDWRE4 can connect a point-of-sale controller, receipt printer, or service terminal that uses a legacy RS-232 port. The two transmitters and two receivers support independent full-duplex channels, while the 250 kbps rate is sufficient for ordinary transaction and status traffic. Using a single +5 V supply avoids requiring a separate negative rail in compact embedded systems. ESD protection on the RS-232 pins is especially useful around cables that can be connected during installation or servicing. Keep the charge-pump network isolated from sensitive signal paths, provide a low-impedance connector ground, and verify that the cable length and baud rate satisfy the selected RS-232 implementation.
Recommandé
Data Acquisition System Communication
The MAX232ECDWRE4 is appropriate for a data-acquisition controller that sends commands and receives sampled results through a legacy RS-232 link. Its full-duplex 2/2 channel arrangement can carry requests in one direction and status or data acknowledgments in the other. Operating from 4.5 V to 5.5 V supports conventional +5 V logic systems, and the on-chip charge-pump circuit removes the need for a negative supply. The interface is limited to 250 kbps, so it is best for control and moderate-rate data rather than continuous high-volume acquisition. Separate the switching charge-pump area from analog input conditioning and use a solid ground connection between the transceiver and cable shield.
Recommandé
Embedded Service and Diagnostics Port
The MAX232ECDWRE4 can provide a service or diagnostics channel on embedded industrial equipment while the main controller uses another communication interface. Independent transmit and receive channels allow status reporting while the technician sends configuration commands. Its dual RS-232 architecture, 250 kbps maximum rate, and +5 V operation fit legacy maintenance ports commonly found in controllers and communication equipment. The MAX232E family's discharge protection reduces vulnerability to electrostatic events encountered during field servicing. Protect the external connector with a short ground path, avoid long unprotected stubs, and separate the transceiver from high-energy switching nodes so that transient energy is not coupled into logic circuitry.
Recommandé
Legacy Computer Serial Peripheral
The MAX232ECDWRE4 is suited to legacy computer peripherals and adapters that use a +5 V UART but require TIA/EIA-232-F signal levels. Its two drivers and two receivers support full-duplex communication, and the 250 kbps limit suits configuration, control, and short data-transfer functions. The internal voltage generator creates the necessary bipolar RS-232 levels from one 5 V supply, reducing system complexity. Use the enhanced-discharge version when the serial connector is exposed to user-accessible cabling. Maintain a continuous ground reference to the transceiver, place the charge-pump capacitors according to the manufacturer layout, and verify cable shielding and enclosure grounding for reliable industrial operation.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX232ECDWRE4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX232ECDWRG4 | MAX232ECDWR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same |
| Product Type | Dual RS-232 driver and receiver transceiver | Dual RS-232 driver and receiver | Dual RS-232 driver and receiver |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps |
| Driver and Receiver Count | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Charge-Pump Capacitors | 4 external capacitors | 4 external capacitors | 4 external capacitors |
| Operating Mode | Full duplex | Full duplex | Full duplex |
Principaux différenciateurs
- Enhanced electrostatic-discharge protection on the external RS-232 pins (vs MAX232ECDWR)
- Single-supply implementation with integrated voltage generation (vs MAX232ECDWRG4)
- Full-duplex two-driver and two-receiver arrangement (vs MAX232ECDWR)
Notes de conception
Place the four external charge-pump capacitors close to the MAX232E capacitor pins, following the Texas Instruments MAX232E datasheet layout and capacitor-value table. Keep the associated traces short and return them through the nearest ground reference. Do not substitute capacitor values based only on package size; capacitance and tolerance affect charge-pump behavior and the resulting RS-232 voltage levels.
Separate the charge-pump and RS-232 driver area from sensitive analog inputs, precision references, and high-impedance measurement circuits. Route the interface ground continuously to the connector shield or chassis-ground interface specified by the system architecture. A common-mode choke can reduce cable-borne noise, but it should be selected and placed in the signal path without creating excessive impedance on the selected data rate.
Do not treat the MAX232ECDWRE4 as a differential RS-485 or RS-422 transceiver. It converts between +5 V TTL/CMOS logic and bipolar TIA/EIA-232-F signals, and its receivers are designed for RS-232 levels rather than the common-mode and failsafe behavior expected from RS-485. Confirm the UART baud rate, cable length, grounding method, and connector pin assignment before releasing the board layout.
The internal voltage generator transfers charge between external capacitors and can create localized high-frequency energy on the PCB. Keep the charge-pump loop compact, provide a nearby ground plane, and avoid routing sensitive signals beneath or immediately beside the capacitor network. If radiated emissions are marginal, inspect the cable shield termination, connector return path, and board edge construction before adding arbitrary extra filtering.
Informations de conformité
The MAX232E datasheet specifies IEC 61000-4-2 electrostatic-discharge levels, but the manufacturer declarations for RoHS, REACH, lead-free status, halogen-free status, and conflict-minerals compliance were not established for this exact orderable code.