Texas Instruments

MAX232ECDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments

MPN: MAX232ECDWRE4 ✓ Aktif
4.5 V to 5.5 V Vdss 16-SOIC, 7.50 mm width Package
MOQ: 1 |

MAX232ECDWRE4 Genel Bakış

Texas Instruments MAX232ECDWRE4 is a +5 V dual RS-232 driver and receiver that provides two transmit channels and two receive channels in a 16-pin SOIC package. It supports data rates up to 250 kbps across a 4.5 V to 5.5 V supply range. Its integrated capacitive voltage generator uses four capacitors to produce the bipolar voltage levels required by TIA/EIA-232-F interfaces from a single 5 V supply.

An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential, bipolar RS-232 signals. It belongs to the serial-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → communication semiconductor. This conversion allows equipment with a logic-level UART to connect to computers, industrial controllers, test equipment, and other RS-232 endpoints through a protected physical interface.

The MAX232ECDWRE4 combines two RS-232 drivers, two receivers, and the charge-pump voltage generator in one package. All RS-232 pins feature 15 kV HBM and 15 kV IEC 61000-4-2 air-gap discharge protection, while RS-232 pins also provide 8 kV IEC 61000-4-2 contact-discharge protection. These ratings make the device appropriate for exposed serial ports where electrostatic discharge is a practical concern.

The charge-pump architecture creates positive and negative RS-232 levels without a negative supply rail. Its four external charge-pump capacitors determine the required energy-transfer behavior and must be placed close to their associated pins. The receiver converts incoming TIA/EIA-232-F signals into 5 V TTL/CMOS levels, while the drivers convert TTL/CMOS inputs into compliant RS-232 output levels. The MAX232E family is optimized for operation from a single +5 V supply.

Typical uses include legacy industrial serial consoles, programmable test equipment, point-of-sale peripherals, data acquisition systems, and service interfaces embedded in larger control systems. The 250 kbps maximum data rate supports moderate-speed asynchronous links rather than high-bandwidth differential serial protocols. Full-duplex operation allows a port to transmit and receive simultaneously through independent channels.

PCB design should prioritize short traces from the charge-pump capacitors to pins 1 and 4, as specified by the Texas Instruments MAX232E datasheet. Keep the interface connector and transceiver pins away from sensitive analog or high-speed digital nodes, and route the ground return with the RS-232 signal path to reduce noise pickup. A common-mode choke can be added when cable emissions or susceptibility become significant.

This page combines the manufacturer interface specifications, protection ratings, package details, verified sourcing information, drop-in alternatives, and practical layout guidance in one engineering-focused reference for evaluating the MAX232ECDWRE4 in +5 V RS-232 designs.

Drop-in alternatifler için MAX232ECDWRE4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller MAX232ECDWRE4 (aynı form faktörü ve ayağa oturma) — farklı olan Number of Receivers, Number of Drivers, Package, Product Type.

Texas Instruments
Package: 16-pin SOIC (DW), 0.295 inch / 7.50 mm width
Product Type: Dual RS-232 driver/receiver
İle Karşılaştır MAX232ECDWRE4 →
Texas Instruments
Number of Receivers: 2 receivers
Number of Drivers: 2 drivers
İle Karşılaştır MAX232ECDWRE4 →

MAX232ECDWRG4

✅ Yerleştirme
Texas Instruments
📦 16-SOIC
2 drivers · 2 receivers · RS-232 transceiver · 120 kbit/s · 5 V · 1.0 uF each · -30 V to +30 V · IEC 61000-4-2

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MAX232ECDWR

✅ Yerleştirme
Texas Instruments
📦 16-SOIC
Dual RS-232 driver/receiver · 2 · 2 · 250 kbps · 4.5 V to 5.5 V · Single 5 V supply · IEC 61000-4-2 · 16-pin SOIC (DW), 0.295 inch / 7.50 mm width

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MAX232ECDWRE4 Özellikler

Product Type Dual RS-232 driver and receiver transceiver
Number of Drivers 2
Number of Receivers 2
Operating Mode Full duplex
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 250 kbps
Interface Standard TIA/EIA-232-F
Logic-Level Interface 5 V TTL/CMOS
Charge-Pump Capacitors 4 external capacitors
HBM ESD Protection 15 kV on all RS-232 pins
IEC 61000-4-2 Air-Gap ESD Protection 15 kV on all RS-232 pins
IEC 61000-4-2 Contact Discharge Protection 8 kV on RS-232 pins
Paket 16-SOIC, 7.50 mm width
Terminal Count 16 terminals
Terminal Form Gull wing
Montaj Türü Surface mount
Temperature Grade Commercial

MAX232ECDWRE4 16-soic, 7.50 mm width Pin Yapısı Kılavuzu

MAX232ECDWRE4 (16-soic, 7.50 mm width paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

16-soic, 7.50 mm width paket pin çizelgesi için MAX232ECDWRE4

Ayrıntılı pin çıkış verisi mevcut değil: MAX232ECDWRE4.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

MAX232ECDWRE4 için uygundur 6 uygulamas: Industrial Equipment Serial Console, Programmable Test Equipment Control, Point-of-Sale Terminal Interface, Data Acquisition System Communication, Embedded Service and Diagnostics Port, Legacy Computer Serial Peripheral.

🏭

Industrial Equipment Serial Console

The MAX232ECDWRE4 fits legacy industrial controllers and service equipment that expose a +5 V UART through an RS-232 connector. Its two driver and two receiver channels support full-duplex communication at up to 250 kbps, while the integrated charge-pump generator eliminates the need for a negative supply rail. The 15 kV IEC 61000-4-2 air-gap and 8 kV contact-discharge ratings add valuable protection for a connector that may be accessible during maintenance. Place the four charge-pump capacitors close to pins 1 and 4, route the cable ground with the signal path, and keep the connector interface away from precision analog circuitry.

🔧

Programmable Test Equipment Control

The MAX232ECDWRE4 is useful in laboratory instruments that retain a host computer or controller interface for configuration, diagnostics, and firmware loading. A 250 kbps RS-232 link is appropriate for command traffic, and the device translates the controller's TTL/CMOS UART signals to and from TIA/EIA-232-F levels. Its dual-channel architecture permits simultaneous command transmission and status reception. The single 5 V supply simplifies isolation and power planning, while the enhanced RS-232-pin discharge ratings improve robustness when the instrument is connected to user-accessible equipment. Use a dedicated protection ground and maintain short charge-pump capacitor traces to prevent switching transients from disturbing precision measurement circuits.

🖥️

Point-of-Sale Terminal Interface

The MAX232ECDWRE4 can connect a point-of-sale controller, receipt printer, or service terminal that uses a legacy RS-232 port. The two transmitters and two receivers support independent full-duplex channels, while the 250 kbps rate is sufficient for ordinary transaction and status traffic. Using a single +5 V supply avoids requiring a separate negative rail in compact embedded systems. ESD protection on the RS-232 pins is especially useful around cables that can be connected during installation or servicing. Keep the charge-pump network isolated from sensitive signal paths, provide a low-impedance connector ground, and verify that the cable length and baud rate satisfy the selected RS-232 implementation.

📡

Data Acquisition System Communication

The MAX232ECDWRE4 is appropriate for a data-acquisition controller that sends commands and receives sampled results through a legacy RS-232 link. Its full-duplex 2/2 channel arrangement can carry requests in one direction and status or data acknowledgments in the other. Operating from 4.5 V to 5.5 V supports conventional +5 V logic systems, and the on-chip charge-pump circuit removes the need for a negative supply. The interface is limited to 250 kbps, so it is best for control and moderate-rate data rather than continuous high-volume acquisition. Separate the switching charge-pump area from analog input conditioning and use a solid ground connection between the transceiver and cable shield.

🧩

Embedded Service and Diagnostics Port

The MAX232ECDWRE4 can provide a service or diagnostics channel on embedded industrial equipment while the main controller uses another communication interface. Independent transmit and receive channels allow status reporting while the technician sends configuration commands. Its dual RS-232 architecture, 250 kbps maximum rate, and +5 V operation fit legacy maintenance ports commonly found in controllers and communication equipment. The MAX232E family's discharge protection reduces vulnerability to electrostatic events encountered during field servicing. Protect the external connector with a short ground path, avoid long unprotected stubs, and separate the transceiver from high-energy switching nodes so that transient energy is not coupled into logic circuitry.

💻

Legacy Computer Serial Peripheral

The MAX232ECDWRE4 is suited to legacy computer peripherals and adapters that use a +5 V UART but require TIA/EIA-232-F signal levels. Its two drivers and two receivers support full-duplex communication, and the 250 kbps limit suits configuration, control, and short data-transfer functions. The internal voltage generator creates the necessary bipolar RS-232 levels from one 5 V supply, reducing system complexity. Use the enhanced-discharge version when the serial connector is exposed to user-accessible cabling. Maintain a continuous ground reference to the transceiver, place the charge-pump capacitors according to the manufacturer layout, and verify cable shielding and enclosure grounding for reliable industrial operation.

What is the operating voltage of MAX232ECDWRE4?
The MAX232ECDWRE4 operates from a single 4.5 V to 5.5 V supply, with 5 V as the nominal operating point. According to the Texas Instruments MAX232E datasheet, its charge-pump voltage generator produces the positive and negative TIA/EIA-232-F levels required by the drivers. The TTL/CMOS receiver outputs and logic-level driver inputs are referenced to the same single supply, simplifying the interface design.
What are the key specifications of MAX232ECDWRE4 that engineers should know?
The MAX232ECDWRE4 is a +5 V, full-duplex dual RS-232 transceiver with two drivers, two receivers, and a maximum data rate of 250 kbps. According to the Texas Instruments MAX232E datasheet, all RS-232 pins provide 15 kV HBM protection and 15 kV IEC 61000-4-2 air-gap discharge protection; RS-232 pins also support 8 kV contact discharge. The device uses 16-SOIC packaging and requires four external charge-pump capacitors.
Where can I download the MAX232ECDWRE4 datasheet PDF?
The official MAX232ECDWRE4 datasheet is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/max232e.pdf. It contains the pin-description table, charge-pump capacitor connections, electrical characteristics, ESD ratings, and typical operating circuits. Use the MAX232E ordering information within the document to confirm the relationship between the MAX232ECDWRE4 orderable code, commercial temperature grade, 16-SOIC package, and tape-and-reel packaging.
Where can I find the MAX232ECDWRE4 pinout?
The MAX232ECDWRE4 pinout is shown in the Pin Description and Pin Configuration sections of the Texas Instruments MAX232E datasheet. Use that manufacturer table to assign the 16 SOIC pins, including the supply, ground, driver inputs and outputs, receiver inputs and outputs, and the four charge-pump capacitor connections. Keep all PCB assignments based on the datasheet numbering so that the physical footprint follows standard counterclockwise SOIC orientation.
What can replace MAX232ECDWRE4?
MAX232ECDWRG4 is the closest identified same-family replacement for the MAX232ECDWRE4 because both use the 16-SOIC interface arrangement and belong to the MAX232E family. MAX232ECDWR is another related 16-SOIC ordering option. Confirm the temperature grade, ESD rating, capacitor values, and ordering suffix for the intended production design before substitution. The manufacturer datasheet remains the controlling document for footprint and function.
Is MAX232ECDWRE4 the same as MAX232ECDWRG4?
MAX232ECDWRE4 and MAX232ECDWRG4 are closely related MAX232E orderable variants in the same 16-SOIC family, but their suffixes identify different ordering conditions. The MAX232ECDWRE4 is identified as a commercial-grade 2/2 full-RS-232 transceiver, while MAX232ECDWRG4 is presented as a separate ordering option in a direct comparison. Check the temperature range, lead finish, packing method, and ESD designation in the ordering table before treating them as interchangeable.
MAX232ECDWRE4 vs MAX232ACDWR - which is better for an industrial console?
The MAX232ECDWRE4 is preferable when electrostatic-disure resilience on the RS-232 connector side is the deciding requirement because its RS-232 pins are specified for 15 kV HBM, 15 kV IEC 61000-4-2 air-gap, and 8 kV contact discharge. Both families use the familiar +5 V RS-232 architecture and a 16-SOIC format. The final choice should also match the required commercial or extended-temperature grade.
When should I choose MAX232ECDWRE4 over MAX232ECDWR?
Choose MAX232ECDWRE4 when the design requires the enhanced ESD-protection designation and operates from a 4.5 V to 5.5 V supply. Choose MAX232ECDWR when its ordering suffix satisfies the environmental and sourcing requirements of the finished product. Both devices use the MAX232E dual-driver, dual-receiver architecture with a 250 kbps maximum data rate, so the selection should focus on grade, protection, packaging, and lifecycle requirements.
Is MAX232ECDWRE4 suitable for a full-duplex RS-232 port?
Yes, the MAX232ECDWRE4 is suitable for a full-duplex RS-232 port because it contains two independent driver channels and two independent receiver channels. It supports asynchronous serial operation up to 250 kbps from a single +5 V supply. The receiver translates TIA/EIA-232-F inputs into 5 V TTL/CMOS levels, while the drivers translate TTL/CMOS inputs into RS-232 levels. Four external capacitors are required for the internal voltage generator.
Does MAX232ECDWRE4 need a negative supply voltage?
No, the MAX232ECDWRE4 does not require an external negative supply. According to the Texas Instruments MAX232E datasheet, its capacitive voltage generator uses four external capacitors to create the required bipolar voltage levels from one +5 V supply. This simplifies system power design, although the charge-pump capacitors must be placed close to their pins and the resulting switching energy should be considered in sensitive analog layouts.
Where can I buy MAX232ECDWRE4 and check current lead time?
Use the Request a Quote form on this page to inquire about the MAX232ECDWRE4, current price, stock, minimum order quantity, and production lead time. The part is a 16-SOIC Texas Instruments RS-232 transceiver, and its exact supply status can change with market conditions. Share the required quantity, shipment destination, and date code requirements when requesting a quotation.
What is the current price of MAX232ECDWRE4?
The current MAX232ECDWRE4 price depends on order quantity, packing method, date code, and market conditions. Use the Request a Quote form on this page for a transaction-ready quotation rather than relying on a static listing value. Include the required quantity, reel or tube preference, delivery location, and target date so the quote reflects the intended production order.
Is MAX232ECDWRE4 in stock and what is its lead time?
The current stock position and manufacturing lead time should be confirmed through the Request a Quote form on this page. For production planning, specify the annual usage, forecast releases, acceptable date-code range, and packaging requirement. The MAX232ECDWRE4 is cataloged as a 16-SOIC commercial-grade device, but live inventory and lead time remain commercial variables that require a quotation response.
What is the best Analog Devices equivalent for MAX232ECDWRE4?
The MAX232 family from Analog Devices is the relevant cross-brand starting point because it uses the same +5 V dual-driver, dual-receiver RS-232 concept. However, a valid drop-in replacement must also use the identical 16-SOIC pin arrangement and satisfy the required ESD, temperature, data-rate, and capacitor values. Compare the Analog Devices MAX232 ordering table directly with the Texas Instruments MAX232E datasheet before approving a cross-brand substitution.
Can MAX232ECDWRE4 provide electrostatic-discharge protection for an external connector?
Yes, the MAX232ECDWRE4 is designed for electrostatic-discharge protection on its RS-232 pins. According to the Texas Instruments MAX232E datasheet, all RS-232 pins support 15 kV HBM and 15 kV IEC 61000-4-2 air-gap discharge, and the RS-232 pins support 8 kV IEC 61000-4-2 contact discharge. Protection ratings do not remove the need for a short connector ground path, controlled cable routing, and an appropriate enclosure.

Mühendislik referans verileri: MAX232ECDWRE4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose MAX232ECDWRE4 for a legacy +5 V RS-232 interface that requires the enhanced-discharge ordering option and a 16-SOIC footprint. MAX232ECDWRG4 is appropriate when its ordering conditions satisfy the production requirements and you need the closely related MAX232E configuration. MAX232ECDWR is another related 16-SOIC option whose grade, ESD designation, packing, and lead-finish conditions should be checked against the finished product. For cross-brand sourcing, start with the Analog Devices MAX232 family, but approve it only after confirming an identical 16-SOIC pin arrangement, matching 4.5 V to 5.5 V operation, suitable data rate, external capacitor requirements, temperature grade, and required ESD performance. None of the MAX232 options should be selected for an RS-485 physical layer merely because the protocol family is similar.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün MAX232ECDWRG4 MAX232ECDWR
Brand Texas Instruments Texas Instruments Texas Instruments
Package 16-SOIC 16-SOIC - same 16-SOIC - same
Product Type Dual RS-232 driver and receiver transceiver Dual RS-232 driver and receiver Dual RS-232 driver and receiver
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps
Driver and Receiver Count 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers
Charge-Pump Capacitors 4 external capacitors 4 external capacitors 4 external capacitors
Operating Mode Full duplex Full duplex Full duplex

Ana Farklılayıcılar

  • Enhanced electrostatic-discharge protection on the external RS-232 pins (karşılaştırma:MAX232ECDWR)
  • Single-supply implementation with integrated voltage generation (karşılaştırma:MAX232ECDWRG4)
  • Full-duplex two-driver and two-receiver arrangement (karşılaştırma:MAX232ECDWR)

Tasarım Notları

Place the four external charge-pump capacitors close to the MAX232E capacitor pins, following the Texas Instruments MAX232E datasheet layout and capacitor-value table. Keep the associated traces short and return them through the nearest ground reference. Do not substitute capacitor values based only on package size; capacitance and tolerance affect charge-pump behavior and the resulting RS-232 voltage levels.

Separate the charge-pump and RS-232 driver area from sensitive analog inputs, precision references, and high-impedance measurement circuits. Route the interface ground continuously to the connector shield or chassis-ground interface specified by the system architecture. A common-mode choke can reduce cable-borne noise, but it should be selected and placed in the signal path without creating excessive impedance on the selected data rate.

Do not treat the MAX232ECDWRE4 as a differential RS-485 or RS-422 transceiver. It converts between +5 V TTL/CMOS logic and bipolar TIA/EIA-232-F signals, and its receivers are designed for RS-232 levels rather than the common-mode and failsafe behavior expected from RS-485. Confirm the UART baud rate, cable length, grounding method, and connector pin assignment before releasing the board layout.

The internal voltage generator transfers charge between external capacitors and can create localized high-frequency energy on the PCB. Keep the charge-pump loop compact, provide a nearby ground plane, and avoid routing sensitive signals beneath or immediately beside the capacitor network. If radiated emissions are marginal, inspect the cable shield termination, connector return path, and board edge construction before adding arbitrary extra filtering.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The MAX232E datasheet specifies IEC 61000-4-2 electrostatic-discharge levels, but the manufacturer declarations for RoHS, REACH, lead-free status, halogen-free status, and conflict-minerals compliance were not established for this exact orderable code.

İlgili Aramalar

MAX232ECDWRE4 datasheet MAX232ECDWRE4 pinout MAX232ECDWRE4 datasheet pdf MAX232ECDWRE4 equivalent MAX232ECDWRE4 replacement MAX232ECDWRE4 cross reference MAX232ECDWRE4 vs MAX232ECDWR MAX232ECDWRE4 footprint MAX232ECDWRE4 application circuit MAX232ECDWRE4 price MAX232ECDWRE4 stock Texas Instruments MAX232ECDWRE4

İlgili Bileşenler ve Terimler

Texas Instruments MAX232ECDWRE4 MAX232ECDWRG4 MAX232ECDWR MAX232E RS-232 TIA/EIA-232-F RS-232 transceiver line driver line receiver interface IC communication semiconductor single-supply transceiver capacitive voltage generator charge-pump capacitor TTL/CMOS UART 250 kbps IEC 61000-4-2 HBM ESD protection 16-SOIC SOIC family surface-mount package industrial serial communication
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle