MAX311CPE+ - 8-Channel CMOS RF/Video Multiplexer | Maxim Integrated
Référence : MAX311CPE+ ✓ ActifMAX311CPE+ Présentation
An analog multiplexer (also called an analog switch or mux) is a passive semiconductor device that steers a signal path between multiple inputs and a shared output under digital control. Within the signal-chain hierarchy, a multiplexer sits above a basic analog switch and below larger interface and routing ICs, and it belongs to the broader category of interface ICs used to build video routing, matrix and switching systems. Modern video and RF equipment typically replaces the mechanical relay or coax switch of the past with CMOS mux trees like the MAX311 family.
Key characteristics of this device include its 8-channel CMOS construction, its operation as a 2:1/4:1-class RF and video routing element, and its ability to handle baseband video and RF signals in the same multiplexed structure. Because the MAX311CPE+ is a through-hole PDIP-16 device, it is easy to prototype on a perfboard or wire into a legacy instrument, and it remains a convenient choice for repair and obsolescence-management work on older professional video and RF test equipment.
Architecturally the part uses CMOS transmission-gate switches with break-before-make control logic, so the control inputs can be driven by standard TTL/CMOS logic and the output never connects two sources together during switching. Signal integrity is the key engineering consideration: with on-resistance, off-isolation, bandwidth and crosstalk all specified by Maxim in the manufacturer data sheet, the MAX311CPE+ is best used with source impedances and cable lengths that do not push the switch into its impedance-sensitive region.
Typical applications include professional video routing and patch equipment, broadcast and studio monitoring paths, RF instrumentation and test sets, and general-purpose analog signal routing in laboratory or industrial control panels where an 8-way RF/video selector is required. It is also widely used in legacy test and measurement platforms as a service replacement part.
When laying out a design around the MAX311CPE+, keep input and output traces short, use a ground plane reference, and place the device close to the signal source to minimise parasitic capacitance on the high-impedance mux node. Confirm the control logic levels and the enable polarity from the manufacturer data sheet before committing to a PCB, because the enable and select decoding arrangement determines how many control lines your host microcontroller must drive.
Alternatives de remplacement direct pour MAX311CPE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
MAX311CPE
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX312CPE+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX313CPE+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX312CSE+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX311CPE+ Spécifications
| Device Type | 8-Channel CMOS RF/Video Multiplexer (Video Switch IC) |
| Manufacturer | Maxim Integrated Products (Analog Devices) |
| Boîtier | 16-pin PDIP (through-hole) |
| Nombre de broches | 16 pins |
| Number of Channels | 8 channels |
| Technology | CMOS analog switch |
| Type de montage | Through-hole |
| Production Status | PRODUCTION (per manufacturer product page) |
| Datasheet Document Size | 252 Kb / 7 pages (per datasheet index listing) |
Guide de configuration des broches du MAX311CPE+ 16-pin pdip (through-hole)
Configuration des broches du MAX311CPE+ (boîtier 16-pin pdip (through-hole)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX311CPE+.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX311CPE+ convient pour 6 applications: Professional Video Routing and Patch Equipment, RF Test and Measurement Instrumentation, Legacy Instrument Repair and Obsolescence Management, Video Wall and Multi-Source Monitoring Systems, Industrial Analog Signal Routing Panels, Educational and Laboratory Electronics.
Professional Video Routing and Patch Equipment
The MAX311CPE+ is well suited to video patch bays and small routing matrices in broadcast, studio and post-production equipment, where eight RF or composite video sources must reach one or two shared outputs. As a CMOS analog multiplexer, it presents a low-impedance signal path with no added gain stage, so the source impedance of the camera or source module determines the signal quality at the output. Because the device is a passive element, any insertion loss shows up directly as a small attenuation of the composite or SDI-adjacent signal, so keep source and destination impedances matched and terminate unused inputs as recommended in the data sheet. The 16-pin PDIP package allows socketed installation in equipment that must be repaired in the field rather than reworked with hot air, which is a decisive practical advantage in long-lived broadcast infrastructure.
Recommandé
RF Test and Measurement Instrumentation
RF bench instruments such as network analysers, spectrum test sets and signal-selection panels use CMOS multiplexers to route one of several sources to a single measurement chain. The MAX311CPE+ fits this role because it provides eight multiplexed channels in a single 16-pin PDIP device, which keeps the RF path count high without a dense surface-mount layout. The engineering caveat is that on-resistance and off-isolation, rather than logic speed, usually set the real accuracy limit in an RF measurement path, so evaluate the published curves against the frequency of interest and the acceptable insertion loss budget. Through-hole construction also means the mux can sit close to the SMA launch on the board, reducing the length of high-impedance transmission line that would otherwise add phase error.
Recommandé
Legacy Instrument Repair and Obsolescence Management
The MAX311CPE+ is frequently the part an engineer reaches for when maintaining older professional video monitors, waveform monitors, RF sweepers and matrix switchers that have been in service for years. Its 16-pin PDIP through-hole package means the existing sockets and board land patterns in those instruments can be reused without a respin, and the availability of a socketed DIP footprint makes board-level replacement a ten-minute task instead of a hot-air rework job. Because the MAX311 family is listed in PRODUCTION status, spares can be bought as new stock rather than salvaged from scrapped equipment. The remaining diligence is to confirm the control polarity and truth table of the installed revision, since earlier instrument builds sometimes used a different logic arrangement around the same family.
Recommandé
Video Wall and Multi-Source Monitoring Systems
Control-room video walls and multiview monitoring desks need to bring many camera or workstation sources to a smaller number of displays, and the MAX311CPE+ provides eight-way RF/video multiplexing in a single inexpensive device. Its CMOS switch architecture means the source is muted only during the brief break-before-make interval, so there is no need for relay click or mechanical wear, which matters in a system that switches sources frequently during live production. Design the input and output nets as controlled-impedance, referenced to a solid ground plane, and keep the multiplexer close to the source buffer so that the passive network loss stays small relative to the source drive level. For installations where the display path is digital rather than analogue RF, this device is used on the analogue side of the chain, feeding ADC or video processor front ends.
Recommandé
Industrial Analog Signal Routing Panels
Industrial test cells, calibration racks and process-control panels often need to present one of several analogue sensors or stimulus sources to a single measurement amplifier or analyser, and the MAX311CPE+ implements that selection passively and reliably. Because there is no active amplification inside the multiplexer, the sensor output impedance and the downstream input impedance form a divider across the switch on-resistance, so high-impedance sources need buffering before they reach the mux node to avoid an unacceptable error. The DIP-16 package is convenient for panel-wiring harnesses and for designs that must survive vibration, since soldered through-hole joints tolerate mechanical cycling better than fine-pitch surface-mount alternatives. Guard the unused inputs and provide a defined logic state at power-up so the selected source does not float during system start-up.
Recommandé
Educational and Laboratory Electronics
Teaching benches and university laboratories use the MAX311CPE+ to demonstrate analog multiplexing, sampling, channel isolation and the practical effect of on-resistance on a measurement chain. The through-hole PDIP-16 package lets students solder the device onto perfboards and breadboard-style breakout boards, and it can be swapped quickly if a pin is damaged during a lab session. It is also convenient for prototyping multi-channel RF front ends, where the select lines can be driven from a microcontroller or logic trainer to demonstrate selection sequencing and settling behaviour. For bench use, keep the supply rails well decoupled and observe the input voltage range and absolute maximum ratings stated by Maxim, since exceeding the supply voltage is the most common cause of failure in student-built multiplexer boards.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX311CPE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Choose the MAX311CPE (leaded ordering) only when a legacy bill of materials calls for that code or when a leaded BOM entry is unavoidable; it is electrically identical and footprint identical. Consider a same-family PDIP sibling such as the MAX312CPE+ or MAX313CPE+ only when on-resistance, isolation or channel grouping in the MAX311 does not satisfy your signal budget - the footprint is shared, but the truth table and control polarity must be re-verified before substitution. Do not plan on the SOIC variants such as the MAX311EWN+ or MAX312ESE as drop-in replacements; they require a different footprint. When in doubt, request a quote for the exact ordering code and confirm the data sheet revision your design is built against.
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX311CPE | MAX312CPE+ | MAX313CPE+ | MAX312CSE+ |
|---|---|---|---|---|---|
| Package | 16-pin PDIP (through-hole) | 16-pin PDIP - identical footprint | 16-pin PDIP - same outline | 16-pin PDIP - same outline | 16-pin PDIP - same outline |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Device Type | 8-Channel CMOS RF/Video Multiplexer | 8-Channel CMOS RF/Video Multiplexer | CMOS RF/Video Multiplexer, family member | CMOS RF/Video Multiplexer, family member | CMOS RF/Video Multiplexer, family member |
| Ordering Suffix | CPE+ (lead-free) | CPE (leaded ordering option) | CPE+ (lead-free) | CPE+ (lead-free) | CSE+ (lead-free) |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
Principaux différenciateurs
- Eight-channel RF/video multiplexing in a single 16-pin PDIP package (vs MAX311EWN+)
- Lead-free '+' ordering option for RoHS-compliant assembly (vs MAX311CPE)
- Lower integration cost than discrete relay or separate switch arrays (vs MAX312CPE+)
Notes de conception
The MAX311CPE+ is a passive CMOS mux, so the on-resistance forms a divider with the source impedance and the receiver input impedance. Before committing to the device, calculate the worst-case attenuation as Ron divided by (Rsource + Rin + Ron) and confirm it sits inside your video or RF level budget. Keep the mux node physically short, referenced to a continuous ground plane, and place the device close to the source buffer so that trace capacitance does not roll off the video bandwidth before the switch itself does.
For the 16-pin PDIP footprint, keep the two rows of through-hole pads on the standard 0.3 inch pitch with 0.6 inch row spacing so the part fits standard sockets and instrument repair tooling. Because this is a DIP package, no thermal pad or thermal relief work is needed, but you should still keep switching current paths away from sensitive analog returns and provide a solid ground plane under and around the device. If the design uses an eight-channel matrix with several MAX311CPE+ devices, leave clearance for socket access so a failed device can be exchanged without desoldering.
The two most common errors with this multiplexer family are misreading the select and enable polarity and exceeding the absolute maximum supply rating. Read the truth table in the Maxim data sheet for your specific order code, because the leaded and '+' orderings share the same die but the control decoding must be confirmed against the data sheet revision you are working from. Also define a definite logic state on the select lines at power-up; floating select inputs can leave the output in an indeterminate state and produce visible switching artefacts on a live video path.
Estimated: with the mux output driving a 75 ohm terminated video node, the loss through the switch plus the cable return path should be budgeted at no more than a few tenths of a dB per stage to avoid degrading a cascaded signal chain. Note that a CMOS switch contributes essentially no switching noise of its own - the real EMI concern is the fast edge of the select lines coupling into the mux node. Route select and enable traces away from the analog input and output nets, and add a ground guard or keepout region between them where board area allows.
Informations de conformité
The '+' ordering suffix on MAX311CPE+ denotes the lead-free build in Maxim Integrated's ordering convention, but no explicit RoHS, REACH or halogen-free declaration for this specific part number was located on the manufacturer product page, so all declarations are recorded as unknown. The device is a commercial, non-automotive part, so AEC-Q100 does not apply. Confirm material compliance documentation with the supplier at order time.