MAX362CPE+ - Quad SPST NO Analog Switch | Analog Devices
Référence : MAX362CPE+ ✓ ActifMAX362CPE+ Présentation
An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX362 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and signal-management semiconductors. Unlike a mechanical relay, it offers faster electronic control, while its precision on-resistance and channel matching help reduce signal degradation when multiple channels are switched.
The MAX362CPE+ features a maximum specified on-resistance below 85 ohms. According to the Analog Devices MAX362 product information, on-resistance can match within 2 ohms between channels and remain flat with a maximum variation of 9 ohms over the analog signal range. These characteristics are important where channel-to-channel gain variation, insertion loss, or switching consistency affects measurement accuracy. The device uses four normally open switches, so each channel is disconnected until its corresponding control input is driven active.
Technical differentiation comes from the combination of four independent channels in one package, low channel on-resistance, close channel matching, and flat resistance behavior. These characteristics make the MAX362 useful when a system needs repeatable analog multiplexing without the larger footprint or higher control complexity of a multi-channel relay matrix. The 16-pin PDIP package is also appropriate for through-hole assembly, prototype boards, test fixtures, and legacy industrial equipment.
Typical uses include multimeter and oscilloscope input routing, automated test equipment, signal routing in data-acquisition systems, sample-and-hold circuitry, and analog measurement front ends. Each switch can route one of four external nodes to a shared destination, allowing a compact controller to select among multiple sensors or sources. Because the MAX362 is normally open, it also supports isolation-style routing where an inactive channel presents an open path.
PCB design should keep each switched signal trace short and place the device close to the signal source or shared destination. Long traces can add parasitic capacitance and inductance, especially when signals change rapidly between the open and closed states. Confirm control-logic levels, supply requirements, allowable input voltage range, and absolute maximum ratings in the manufacturer datasheet before finalizing the interface circuit.
This product page combines the manufacturer function description, package and switching characteristics, lifecycle information, sourcing guidance, and application-focused design guidance. It also distinguishes verified drop-in alternatives from functionally related but mechanically or electrically unsuitable parts, helping engineers shorten component-selection and PCB-validation work.
Alternatives de remplacement direct pour MAX362CPE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX362CPE+ (même facteur de forme et même empreinte) — différant par AEC-Q100 Qualification, Mounting Type, On-Resistance Flatness, Package, Switch Configuration.
MAX362CPE
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX362EPE+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX362EP
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX362EP+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX362CPE+ Valeurs maximales et caractéristiques électriques
| Number of Switches | 4 circuits |
| Switch Configuration | 4 independent SPST channels |
| Multiplexer Configuration | 1:1 |
| Switch State | Normally open (NO) |
| Maximum On-Resistance | 85 ohm |
| On-Resistance Matching Between Channels | Within 2 ohm |
| Maximum On-Resistance Variation Over Analog Signal Range | 9 ohm |
| Boîtier | 16-pin PDIP |
| Nombre de broches | 16 pins |
| Type de montage | Through-hole |
| Technology | CMOS analog switch |
| On-Resistance Flatness | Maximum variation of 9 ohm over the analog signal range |
| Statut RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guide de configuration des broches du MAX362CPE+ 16-pin pdip
Configuration des broches du MAX362CPE+ (boîtier 16-pin pdip). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX362CPE+.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX362CPE+ convient pour 6 applications: Automated Test Equipment Signal Routing, Multimeter Input Multiplexing, Sensor Signal Selection, Sample-and-Hold Signal Control, Oscilloscope Multi-Channel Source Selection, Analog Isolation and Signal Gating.
Automated Test Equipment Signal Routing
The MAX362CPE+ is appropriate for automated test equipment that selects among several analog sources or instrument inputs through a shared measurement path. Its four normally open SPST channels provide independent routing, while the specified on-resistance below 85 ohms limits insertion loss in the selected path. Channel-to-channel matching within 2 ohms helps reduce test-result variation when different channels are selected. Place the device near the connector or measurement node to minimize trace capacitance, and use the manufacturer control levels to define the default open state safely.
Recommandé
Multimeter Input Multiplexing
MAX362CPE+ can route four measured nodes toward a common multimeter or analog front-end input, making it useful in handheld and bench instruments that must select different sources. The less-than-85-ohm on-resistance specification helps preserve signal integrity, and the maximum 9-ohm variation across the analog range limits gain errors caused by resistance flatness. Its normally open channels isolate unselected inputs until control logic selects one path. Layout should minimize resistance and capacitance between the switch, protection network, and analog measurement input.
Recommandé
Sensor Signal Selection
The MAX362CPE+ can connect one of four sensor outputs to a shared amplifier, ADC, or controller input in industrial sensing systems. Close on-resistance matching within 2 ohms helps maintain more consistent channel attenuation, while flat on-resistance below the 85-ohm maximum supports predictable behavior across the analog signal range. Because the switches are normally open, the inactive sensor paths remain disconnected unless their control inputs are asserted. Select control-logic levels and validate input capacitance before using the device with high-impedance sensors.
Recommandé
Sample-and-Hold Signal Control
MAX362CPE+ can select the signal presented to a sample-and-hold or track-and-hold stage in precision instrumentation. Four independent normally open paths allow different sources to be connected under digital control, while the specified resistance matching and flatness help reduce channel-dependent settling and gain differences. Keep the common destination trace short and place bypass or hold-capacitor connections according to the analog design to prevent the switch and board parasitics from dominating acquisition accuracy.
Recommandé
Oscilloscope Multi-Channel Source Selection
The MAX362CPE+ supports selectable source routing in oscilloscope and waveform-measurement systems where multiple nodes must reach a shared vertical input. Its four SPST channels provide compact multiplexing, and the below-85-ohm on-resistance minimizes added attenuation compared with a higher-resistance switch. Matching within 2 ohms helps maintain similar channel response. Engineers should still account for switch capacitance, control timing, and the bandwidth of the surrounding analog path when configuring high-speed or high-impedance measurements.
Recommandé
Analog Isolation and Signal Gating
MAX362CPE+ can implement analog signal gating in test fixtures, interface boards, and measurement adapters by disconnecting a source from a shared node until its control input is active. The normally open topology is useful when an inactive path must remain electrically separated, while the 85-ohm maximum on-resistance limits insertion loss in the active state. Confirm allowable signal voltage, off leakage, and switching transients in the manufacturer electrical characteristics, and use a ground reference appropriate for the signals being switched.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX362CPE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX362CPE | MAX362EPE+ | MAX362EP | MAX362EP+ |
|---|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Switches | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels |
| Switch State | Normally open | Normally open | Normally open | Normally open | Normally open |
| Maximum On-Resistance | 85 ohm | 85 ohm | 85 ohm | 85 ohm | 85 ohm |
| On-Resistance Matching Between Channels | Within 2 ohm | Within 2 ohm | Within 2 ohm | Within 2 ohm | Within 2 ohm |
| Maximum On-Resistance Variation Over Analog Signal Range | 9 ohm | 9 ohm | 9 ohm | 9 ohm | 9 ohm |
| Multiplexer Configuration | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
Principaux différenciateurs
- Four-channel precision routing in one 16-pin package (vs MAX362CPE)
- Close resistance matching reduces channel-dependent error (vs MAX362EPE+)
- Flat on-resistance across the analog signal range (vs MAX362EP)
Notes de conception
Place the MAX362CPE+ next to the common analog destination and keep each switched trace short. Long PCB traces add parasitic capacitance and inductance that can increase transition time and disturb sensitive measurements. Route the four analog paths away from switching-control and digital timing nets, and use a continuous ground reference to minimize coupling between the selected signal and adjacent channels.
Evaluate switch capacitance and off-state leakage together with the impedance of the selected source. The specified on-resistance below 85 ohms limits resistive insertion loss, but a high-impedance sensor or very high-frequency signal can still be affected by parasitic capacitance. Confirm the complete signal path with the manufacturer electrical characteristics and use the maximum signal amplitude and bandwidth of the intended measurement.
Do not treat MAX362 as a normally closed switch. MAX362 uses four normally open channels, while the related MAX361 family uses normally closed channels. Although the package dimensions can be similar, the inactive signal path is electrically opposite. Review the control truth table, startup state, fault condition, and signal-level requirements before approving either device for a safety-sensitive or fail-state-dependent circuit.
Use a 16-pin through-hole footprint whose drill pattern and pin numbering match the manufacturer package drawing. Confirm the orientation and pin-1 location on the PCB against the actual component marking. Avoid combining a 16-pin PDIP footprint with a surface-mount SOIC variant even when both use 16 terminals, because lead pitch, body size, and assembly method are different.
Informations de conformité
The available product information does not state the requested compliance or material-status classifications. These fields remain unknown rather than being inferred from the package family or producer ordering code.