Analog Devices

MAX362CPE+ - Quad SPST NO Analog Switch | Analog Devices

MPN: MAX362CPE+ ✓ 啟用中
85 ohm Rds(on) 16-pin PDIP Package
MOQ: 1 |

MAX362CPE+ 概覽

The Analog Devices MAX362CPE+ is a precision quad single-pole single-throw analog switch with four normally open channels, less than 85 ohms on-resistance, and a 16-pin PDIP package. It provides a 1:1 signal-routing architecture for analog and digital test systems, measurement equipment, instrumentation, and signal isolation applications. Each of the four independent switches connects one external signal terminal to one common signal terminal when its control input is asserted.

An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX362 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and signal-management semiconductors. Unlike a mechanical relay, it offers faster electronic control, while its precision on-resistance and channel matching help reduce signal degradation when multiple channels are switched.

The MAX362CPE+ features a maximum specified on-resistance below 85 ohms. According to the Analog Devices MAX362 product information, on-resistance can match within 2 ohms between channels and remain flat with a maximum variation of 9 ohms over the analog signal range. These characteristics are important where channel-to-channel gain variation, insertion loss, or switching consistency affects measurement accuracy. The device uses four normally open switches, so each channel is disconnected until its corresponding control input is driven active.

Technical differentiation comes from the combination of four independent channels in one package, low channel on-resistance, close channel matching, and flat resistance behavior. These characteristics make the MAX362 useful when a system needs repeatable analog multiplexing without the larger footprint or higher control complexity of a multi-channel relay matrix. The 16-pin PDIP package is also appropriate for through-hole assembly, prototype boards, test fixtures, and legacy industrial equipment.

Typical uses include multimeter and oscilloscope input routing, automated test equipment, signal routing in data-acquisition systems, sample-and-hold circuitry, and analog measurement front ends. Each switch can route one of four external nodes to a shared destination, allowing a compact controller to select among multiple sensors or sources. Because the MAX362 is normally open, it also supports isolation-style routing where an inactive channel presents an open path.

PCB design should keep each switched signal trace short and place the device close to the signal source or shared destination. Long traces can add parasitic capacitance and inductance, especially when signals change rapidly between the open and closed states. Confirm control-logic levels, supply requirements, allowable input voltage range, and absolute maximum ratings in the manufacturer datasheet before finalizing the interface circuit.

This product page combines the manufacturer function description, package and switching characteristics, lifecycle information, sourcing guidance, and application-focused design guidance. It also distinguishes verified drop-in alternatives from functionally related but mechanically or electrically unsuitable parts, helping engineers shorten component-selection and PCB-validation work.

直接替換替代品,適用於 MAX362CPE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: MAX362CPE+ (相同外形與佔位) — 差異在於 AEC-Q100 Qualification, Mounting Type, On-Resistance Flatness, Package, Switch Configuration.

Maxim Integrated
AEC-Q100 Qualification: not_applicable
Mounting Type: Through hole
On-Resistance Flatness: 9 ohm maximum over the signal range
比較對象 MAX362CPE+ →

MAX362CPE

✅ 直接替換
📦 PDIP-16
Same four normally open SPST channels, 85 ohm maximum on-resistance, and 16-pin PDIP footprint; electrical on-resistance difference is 0%

📋 參考替代品(不在目錄中)

MAX362EPE+

✅ 直接替換 ⚠️ 規格未經驗證
📦 PDIP-16
Same 85 ohm maximum on-resistance and 16-pin PDIP footprint; on-resistance difference is 0%, with a different temperature-grade ordering code

📋 參考替代品(不在目錄中)

MAX362EP

✅ 直接替換 ⚠️ 規格未經驗證
📦 PDIP-16
Same 85 ohm maximum on-resistance and 16-pin PDIP footprint; on-resistance difference is 0%, with a different temperature-grade ordering code

📋 參考替代品(不在目錄中)

MAX362EP+

✅ 直接替換 ⚠️ 規格未經驗證
📦 PDIP-16
Same 85 ohm maximum on-resistance and 16-pin PDIP footprint; on-resistance difference is 0%, with a different temperature-grade ordering code

📋 參考替代品(不在目錄中)

MAX362CPE+ 最大額定值與電氣特性

Number of Switches 4 circuits
Switch Configuration 4 independent SPST channels
Multiplexer Configuration 1:1
Switch State Normally open (NO)
Maximum On-Resistance 85 ohm
On-Resistance Matching Between Channels Within 2 ohm
Maximum On-Resistance Variation Over Analog Signal Range 9 ohm
封裝 16-pin PDIP
腳位數 16 pins
安裝類型 Through-hole
Technology CMOS analog switch
On-Resistance Flatness Maximum variation of 9 ohm over the analog signal range
RoHS 狀態 unknown
REACH Status unknown
AEC-Q100 Qualification unknown

MAX362CPE+ 16-pin pdip 腳位配置指南

MAX362CPE+(16-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

MAX362CPE+ 的 16-pin pdip 封裝腳位圖

無詳細腳位定義資料: MAX362CPE+.

請參閱 資料表 以查看完整腳位配置。

典型應用

MAX362CPE+ 適用於 6 應用s: Automated Test Equipment Signal Routing, Multimeter Input Multiplexing, Sensor Signal Selection, Sample-and-Hold Signal Control, Oscilloscope Multi-Channel Source Selection, Analog Isolation and Signal Gating.

🖥️

Automated Test Equipment Signal Routing

The MAX362CPE+ is appropriate for automated test equipment that selects among several analog sources or instrument inputs through a shared measurement path. Its four normally open SPST channels provide independent routing, while the specified on-resistance below 85 ohms limits insertion loss in the selected path. Channel-to-channel matching within 2 ohms helps reduce test-result variation when different channels are selected. Place the device near the connector or measurement node to minimize trace capacitance, and use the manufacturer control levels to define the default open state safely.

🔧

Multimeter Input Multiplexing

MAX362CPE+ can route four measured nodes toward a common multimeter or analog front-end input, making it useful in handheld and bench instruments that must select different sources. The less-than-85-ohm on-resistance specification helps preserve signal integrity, and the maximum 9-ohm variation across the analog range limits gain errors caused by resistance flatness. Its normally open channels isolate unselected inputs until control logic selects one path. Layout should minimize resistance and capacitance between the switch, protection network, and analog measurement input.

🏭

Sensor Signal Selection

The MAX362CPE+ can connect one of four sensor outputs to a shared amplifier, ADC, or controller input in industrial sensing systems. Close on-resistance matching within 2 ohms helps maintain more consistent channel attenuation, while flat on-resistance below the 85-ohm maximum supports predictable behavior across the analog signal range. Because the switches are normally open, the inactive sensor paths remain disconnected unless their control inputs are asserted. Select control-logic levels and validate input capacitance before using the device with high-impedance sensors.

📡

Sample-and-Hold Signal Control

MAX362CPE+ can select the signal presented to a sample-and-hold or track-and-hold stage in precision instrumentation. Four independent normally open paths allow different sources to be connected under digital control, while the specified resistance matching and flatness help reduce channel-dependent settling and gain differences. Keep the common destination trace short and place bypass or hold-capacitor connections according to the analog design to prevent the switch and board parasitics from dominating acquisition accuracy.

📺

Oscilloscope Multi-Channel Source Selection

The MAX362CPE+ supports selectable source routing in oscilloscope and waveform-measurement systems where multiple nodes must reach a shared vertical input. Its four SPST channels provide compact multiplexing, and the below-85-ohm on-resistance minimizes added attenuation compared with a higher-resistance switch. Matching within 2 ohms helps maintain similar channel response. Engineers should still account for switch capacitance, control timing, and the bandwidth of the surrounding analog path when configuring high-speed or high-impedance measurements.

🧩

Analog Isolation and Signal Gating

MAX362CPE+ can implement analog signal gating in test fixtures, interface boards, and measurement adapters by disconnecting a source from a shared node until its control input is active. The normally open topology is useful when an inactive path must remain electrically separated, while the 85-ohm maximum on-resistance limits insertion loss in the active state. Confirm allowable signal voltage, off leakage, and switching transients in the manufacturer electrical characteristics, and use a ground reference appropriate for the signals being switched.

推薦產品摘要

MAX362CPE Same-family alternate ordering code for quad SPST routing 用於: Automated Test Equipment Signal Routing, Sensor Signal Selection, Sample-and-Hold Signal Control, Analog Isolation and Signal Gating MAX362EPE+ Same-family temperature-grade option 用於: Automated Test Equipment Signal Routing, Sensor Signal Selection, Oscilloscope Multi-Channel Source Selection MAX361CPE Normally closed complementary switching family 用於: Multimeter Input Multiplexing, Oscilloscope Multi-Channel Source Selection MAX362EP Same-family legacy temperature-grade alternative 用於: Multimeter Input Multiplexing, Analog Isolation and Signal Gating MAX362EP+ Same-family package-compatible routing option 用於: Sample-and-Hold Signal Control
What is the MAX362CPE+ and what does it do?
The MAX362CPE+ is a precision quad analog switch containing four independent, normally open SPST channels in a 16-pin PDIP package. According to the Analog Devices MAX362 datasheet, each channel has an on-resistance below 85 ohms, allowing a controller to route one of several external signals to a shared analog or measurement node. The four-channel 1:1 arrangement saves board space compared with four separate single switches.
Is MAX362CPE+ a normally open or normally closed switch?
The MAX362CPE+ contains four normally open switches, meaning each switched path is disconnected until its control input activates that channel. The related MAX361 family member uses normally closed switches instead. According to the Analog Devices MAX362 product description, the MAX362 on-resistance remains below 85 ohms, while channel matching is within 2 ohms. This distinction is critical because the two switch families cannot be interchanged without accounting for different resting signal paths.
Where can I download the MAX362CPE+ datasheet PDF?
The official MAX362 datasheet and product documentation are available from the Analog Devices product page linked in the Product Resources section of this listing. The manufacturer identifies the document as the MAX362 Data Sheet, Revision 2. Engineers should use the pin-description table, electrical characteristics, absolute maximum ratings, and typical application circuits from that document when assigning PCB tracks and validating control-logic levels.
Where can I find the MAX362CPE+ pinout?
The MAX362CPE+ pinout is shown in the manufacturer datasheet on the Analog Devices MAX362 product page. The component is a 16-pin PDIP device with four SPST channels and four associated control inputs. Use the numbering shown on the package and in the datasheet pin-description table when laying out the through-hole footprint, especially because each analog terminal must be connected to the correct common or input node.
What are the key specifications of MAX362CPE+ that engineers should know?
The key MAX362CPE+ specifications are four normally open SPST channels, a 1:1 routing arrangement, less than 85 ohms on-resistance, within 2 ohms of channel-to-channel resistance matching, and no more than 9 ohms of resistance variation over the analog signal range. The device is packaged in a 16-pin PDIP. According to the Analog Devices MAX362 datasheet, these characteristics support repeatable signal selection in precision analog test and measurement circuits.
What can replace MAX362CPE+ as a drop-in part?
MAX362CPE is the closest verified drop-in replacement because it retains the same four normally open SPST channels, less than 85 ohms on-resistance, and 16-pin PDIP package. MAX362EPE+ and MAX362EP are same-family temperature-grade options in the same mechanically compatible package, but their control, voltage, and environmental requirements should be checked against the manufacturer datasheet before substitution. Confirm the exact ordering code and production status during purchasing.
Is MAX362CPE+ equivalent to MAX361CPE+?
No. MAX362CPE+ has four normally open switches, whereas MAX361CPE+ has four normally closed switches. Although both families use a 16-pin PDIP format and share the quad precision analog-switch architecture, their default electrical states are functionally opposite. A physical substitution would therefore require circuit-level verification and may change signal behavior when control inputs are inactive.
When should I choose MAX362CPE+ over MAX362CPE?
Choose MAX362CPE+ when the preferred ordering code is the lead-free-style production designation for the MAX362 16-pin PDIP device. Choose MAX362CPE when that exact legacy ordering code is required by an existing bill of materials or approved second source. Both identify the same core quad, normally open SPST switch family, so the decision should be based on exact orderability, lifecycle status, documentation, and qualification requirements rather than assumed electrical differences.
MAX362CPE+ vs MAX362CPE+ temperature-grade alternatives: which should I use?
Use MAX362CPE+ as the baseline selection for a 16-pin PDIP, quad normally open SPST switch with less than 85 ohms on-resistance. Use MAX362EPE+ or MAX362EP when a broader industrial temperature grade is required and the manufacturer confirms that its control levels and electrical ratings satisfy the circuit. The MAX362 family is optimized for precision signal routing, but environmental qualification must be matched to the deployment rather than inferred from package compatibility alone.
Where can I buy MAX362CPE+ and check price, stock, and lead time?
Use the Request a Quote form on this page to request current MAX362CPE+ pricing, stock, minimum order quantity, and production lead time. The form is the appropriate channel for a quote-based sourcing request and avoids publishing a stale price. Include the exact 16-pin PDIP ordering code, target quantity, delivery location, and required inspection documentation in the request.
What is the lead time for MAX362CPE+?
Current lead time for MAX362CPE+ should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, package availability, and manufacturing conditions, so a fixed interval should not be assumed for an individual production schedule. Provide the required quantity and target date so procurement can confirm the most relevant supply commitment.
Is MAX362CPE+ in stock?
Current MAX362CPE+ stock should be confirmed through the Request a Quote form on this page. The Analog Devices product page identifies the MAX362 family as production, but family-level production status does not establish inventory for every ordering code. A written quotation can confirm available quantity, scheduling, and any traceability requirements for the selected 16-pin PDIP package.
What is the best cross-brand equivalent for MAX362CPE+?
No cross-brand drop-in equivalent can be confirmed from the available cross-reference results for MAX362CPE+. A valid alternative must provide four normally open SPST channels in the same 16-pin PDIP footprint, remain below 85 ohms on-resistance, preserve compatible control logic, and meet the required signal-voltage and temperature limits. Request a manufacturer cross-reference or submit a complete parameter set for engineering review rather than treating a generic quad analog switch as interchangeable.
Is MAX362CPE+ suitable for precision test and measurement equipment?
Yes, MAX362CPE+ is suitable for precision test and measurement signal routing when its voltage and temperature ratings meet the design limits. The manufacturer specifies less than 85 ohms on-resistance, channel matching within 2 ohms, and resistance variation limited to 9 ohms over the analog signal range. Those parameters reduce channel-dependent attenuation, making the device appropriate for multiplexed sensor, source, and instrument-routing circuits.
How should I design around MAX362CPE+ on a PCB?
Place the MAX362CPE+ close to the switched nodes and route each analog path directly to its assigned pin. Keep the common-node traces short, avoid long stubs, and maintain a solid ground reference beneath the board-level signal paths. Because the four channels are normally open, confirm the control logic and inactive-state behavior in system power-up and fault scenarios. Validate leakage, capacitance, bandwidth, and maximum signal voltage against the manufacturer electrical characteristics.

工程參考資料,適用於 MAX362CPE+ — 比較、設計指引及合規資訊。

選型指南

Choose MAX362CPE+ for a new design requiring four normally open SPST channels, less than 85 ohms on-resistance, and a 16-pin through-hole package. Select MAX362CPE when the legacy ordering code is specifically required or offers better procurement continuity, because its core switching ratings match. Use MAX362EPE+, MAX362EP, or MAX362EP+ when an extended temperature grade is required and the manufacturer confirms the control levels, voltage limits, and qualification match the application. Do not choose MAX361 as a drop-in substitute for MAX362 unless the circuit is deliberately redesigned for normally closed behavior. No cross-brand replacement should be approved solely from package similarity; the switch state, on-resistance, control logic, signal-voltage range, leakage, capacitance, and environmental requirements must all be reviewed before PCB reuse.

與替代品比較

參數 本產品 MAX362CPE MAX362EPE+ MAX362EP MAX362EP+
Package PDIP-16 PDIP-16 PDIP-16 PDIP-16 PDIP-16
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Number of Switches 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
Switch Configuration 4 independent SPST channels 4 independent SPST channels 4 independent SPST channels 4 independent SPST channels 4 independent SPST channels
Switch State Normally open Normally open Normally open Normally open Normally open
Maximum On-Resistance 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm
On-Resistance Matching Between Channels Within 2 ohm Within 2 ohm Within 2 ohm Within 2 ohm Within 2 ohm
Maximum On-Resistance Variation Over Analog Signal Range 9 ohm 9 ohm 9 ohm 9 ohm 9 ohm
Multiplexer Configuration 1:1 1:1 1:1 1:1 1:1
Mounting Type Through-hole Through-hole Through-hole Through-hole Through-hole

主要差異化特點

  • Four-channel precision routing in one 16-pin package (對比MAX362CPE)
  • Close resistance matching reduces channel-dependent error (對比MAX362EPE+)
  • Flat on-resistance across the analog signal range (對比MAX362EP)

設計說明

Place the MAX362CPE+ next to the common analog destination and keep each switched trace short. Long PCB traces add parasitic capacitance and inductance that can increase transition time and disturb sensitive measurements. Route the four analog paths away from switching-control and digital timing nets, and use a continuous ground reference to minimize coupling between the selected signal and adjacent channels.

Evaluate switch capacitance and off-state leakage together with the impedance of the selected source. The specified on-resistance below 85 ohms limits resistive insertion loss, but a high-impedance sensor or very high-frequency signal can still be affected by parasitic capacitance. Confirm the complete signal path with the manufacturer electrical characteristics and use the maximum signal amplitude and bandwidth of the intended measurement.

Do not treat MAX362 as a normally closed switch. MAX362 uses four normally open channels, while the related MAX361 family uses normally closed channels. Although the package dimensions can be similar, the inactive signal path is electrically opposite. Review the control truth table, startup state, fault condition, and signal-level requirements before approving either device for a safety-sensitive or fail-state-dependent circuit.

Use a 16-pin through-hole footprint whose drill pattern and pin numbering match the manufacturer package drawing. Confirm the orientation and pin-1 location on the PCB against the actual component marking. Avoid combining a 16-pin PDIP footprint with a surface-mount SOIC variant even when both use 16 terminals, because lead pitch, body size, and assembly method are different.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The available product information does not state the requested compliance or material-status classifications. These fields remain unknown rather than being inferred from the package family or producer ordering code.

資料驗證日期: 2026-11-19 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

MAX362CPE+ datasheet MAX362CPE+ pinout MAX362CPE+ datasheet pdf MAX362CPE+ equivalent MAX362CPE+ replacement MAX362CPE+ cross reference MAX362CPE+ footprint MAX362CPE+ application circuit MAX362CPE+ price MAX362CPE+ stock Analog Devices MAX362CPE+ MAX362CPE+ 85 ohm SPST

相關元件與詞彙

Analog Devices MAX362CPE+ MAX362CPE MAX362EPE+ MAX362EP MAX362EP+ MAX361 precision analog switch SPST switch normally open switch analog multiplexer interface IC signal-management semiconductor 85 ohm on-resistance channel resistance matching on-resistance flatness PDIP-16 DIP package family through-hole package automated test equipment data acquisition sensor signal selection oscilloscope signal routing RoHS REACH
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情