MAX362CPE+ - Quad SPST NO Analog Switch | Analog Devices
料号: MAX362CPE+ ✓ 量产中MAX362CPE+ 概述
An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX362 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and signal-management semiconductors. Unlike a mechanical relay, it offers faster electronic control, while its precision on-resistance and channel matching help reduce signal degradation when multiple channels are switched.
The MAX362CPE+ features a maximum specified on-resistance below 85 ohms. According to the Analog Devices MAX362 product information, on-resistance can match within 2 ohms between channels and remain flat with a maximum variation of 9 ohms over the analog signal range. These characteristics are important where channel-to-channel gain variation, insertion loss, or switching consistency affects measurement accuracy. The device uses four normally open switches, so each channel is disconnected until its corresponding control input is driven active.
Technical differentiation comes from the combination of four independent channels in one package, low channel on-resistance, close channel matching, and flat resistance behavior. These characteristics make the MAX362 useful when a system needs repeatable analog multiplexing without the larger footprint or higher control complexity of a multi-channel relay matrix. The 16-pin PDIP package is also appropriate for through-hole assembly, prototype boards, test fixtures, and legacy industrial equipment.
Typical uses include multimeter and oscilloscope input routing, automated test equipment, signal routing in data-acquisition systems, sample-and-hold circuitry, and analog measurement front ends. Each switch can route one of four external nodes to a shared destination, allowing a compact controller to select among multiple sensors or sources. Because the MAX362 is normally open, it also supports isolation-style routing where an inactive channel presents an open path.
PCB design should keep each switched signal trace short and place the device close to the signal source or shared destination. Long traces can add parasitic capacitance and inductance, especially when signals change rapidly between the open and closed states. Confirm control-logic levels, supply requirements, allowable input voltage range, and absolute maximum ratings in the manufacturer datasheet before finalizing the interface circuit.
This product page combines the manufacturer function description, package and switching characteristics, lifecycle information, sourcing guidance, and application-focused design guidance. It also distinguishes verified drop-in alternatives from functionally related but mechanically or electrically unsuitable parts, helping engineers shorten component-selection and PCB-validation work.
直接替换替代料: MAX362CPE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX362CPE+ (相同外形与封装尺寸) ——差异在于 AEC-Q100 Qualification, Mounting Type, On-Resistance Flatness, Package, Switch Configuration.
MAX362CPE
✅ 直接替换📋 参考替代料(不在目录中)
MAX362EPE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX362EP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX362EP+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX362CPE+ 最大额定值与电气特性
| Number of Switches | 4 circuits |
| Switch Configuration | 4 independent SPST channels |
| Multiplexer Configuration | 1:1 |
| Switch State | Normally open (NO) |
| Maximum On-Resistance | 85 ohm |
| On-Resistance Matching Between Channels | Within 2 ohm |
| Maximum On-Resistance Variation Over Analog Signal Range | 9 ohm |
| 封装 | 16-pin PDIP |
| 引脚数量 | 16 pins |
| 安装类型 | Through-hole |
| Technology | CMOS analog switch |
| On-Resistance Flatness | Maximum variation of 9 ohm over the analog signal range |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
MAX362CPE+ 16-pin pdip 引脚配置指南
MAX362CPE+(16-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX362CPE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX362CPE+ 适用于 6 应用s: Automated Test Equipment Signal Routing, Multimeter Input Multiplexing, Sensor Signal Selection, Sample-and-Hold Signal Control, Oscilloscope Multi-Channel Source Selection, Analog Isolation and Signal Gating.
Automated Test Equipment Signal Routing
The MAX362CPE+ is appropriate for automated test equipment that selects among several analog sources or instrument inputs through a shared measurement path. Its four normally open SPST channels provide independent routing, while the specified on-resistance below 85 ohms limits insertion loss in the selected path. Channel-to-channel matching within 2 ohms helps reduce test-result variation when different channels are selected. Place the device near the connector or measurement node to minimize trace capacitance, and use the manufacturer control levels to define the default open state safely.
推荐
Multimeter Input Multiplexing
MAX362CPE+ can route four measured nodes toward a common multimeter or analog front-end input, making it useful in handheld and bench instruments that must select different sources. The less-than-85-ohm on-resistance specification helps preserve signal integrity, and the maximum 9-ohm variation across the analog range limits gain errors caused by resistance flatness. Its normally open channels isolate unselected inputs until control logic selects one path. Layout should minimize resistance and capacitance between the switch, protection network, and analog measurement input.
推荐
Sensor Signal Selection
The MAX362CPE+ can connect one of four sensor outputs to a shared amplifier, ADC, or controller input in industrial sensing systems. Close on-resistance matching within 2 ohms helps maintain more consistent channel attenuation, while flat on-resistance below the 85-ohm maximum supports predictable behavior across the analog signal range. Because the switches are normally open, the inactive sensor paths remain disconnected unless their control inputs are asserted. Select control-logic levels and validate input capacitance before using the device with high-impedance sensors.
推荐
Sample-and-Hold Signal Control
MAX362CPE+ can select the signal presented to a sample-and-hold or track-and-hold stage in precision instrumentation. Four independent normally open paths allow different sources to be connected under digital control, while the specified resistance matching and flatness help reduce channel-dependent settling and gain differences. Keep the common destination trace short and place bypass or hold-capacitor connections according to the analog design to prevent the switch and board parasitics from dominating acquisition accuracy.
推荐
Oscilloscope Multi-Channel Source Selection
The MAX362CPE+ supports selectable source routing in oscilloscope and waveform-measurement systems where multiple nodes must reach a shared vertical input. Its four SPST channels provide compact multiplexing, and the below-85-ohm on-resistance minimizes added attenuation compared with a higher-resistance switch. Matching within 2 ohms helps maintain similar channel response. Engineers should still account for switch capacitance, control timing, and the bandwidth of the surrounding analog path when configuring high-speed or high-impedance measurements.
推荐
Analog Isolation and Signal Gating
MAX362CPE+ can implement analog signal gating in test fixtures, interface boards, and measurement adapters by disconnecting a source from a shared node until its control input is active. The normally open topology is useful when an inactive path must remain electrically separated, while the 85-ohm maximum on-resistance limits insertion loss in the active state. Confirm allowable signal voltage, off leakage, and switching transients in the manufacturer electrical characteristics, and use a ground reference appropriate for the signals being switched.
推荐
推荐产品汇总
工程参考数据: MAX362CPE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX362CPE | MAX362EPE+ | MAX362EP | MAX362EP+ |
|---|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Switches | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels |
| Switch State | Normally open | Normally open | Normally open | Normally open | Normally open |
| Maximum On-Resistance | 85 ohm | 85 ohm | 85 ohm | 85 ohm | 85 ohm |
| On-Resistance Matching Between Channels | Within 2 ohm | Within 2 ohm | Within 2 ohm | Within 2 ohm | Within 2 ohm |
| Maximum On-Resistance Variation Over Analog Signal Range | 9 ohm | 9 ohm | 9 ohm | 9 ohm | 9 ohm |
| Multiplexer Configuration | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
关键差异点
- Four-channel precision routing in one 16-pin package (对比 MAX362CPE)
- Close resistance matching reduces channel-dependent error (对比 MAX362EPE+)
- Flat on-resistance across the analog signal range (对比 MAX362EP)
设计说明
Place the MAX362CPE+ next to the common analog destination and keep each switched trace short. Long PCB traces add parasitic capacitance and inductance that can increase transition time and disturb sensitive measurements. Route the four analog paths away from switching-control and digital timing nets, and use a continuous ground reference to minimize coupling between the selected signal and adjacent channels.
Evaluate switch capacitance and off-state leakage together with the impedance of the selected source. The specified on-resistance below 85 ohms limits resistive insertion loss, but a high-impedance sensor or very high-frequency signal can still be affected by parasitic capacitance. Confirm the complete signal path with the manufacturer electrical characteristics and use the maximum signal amplitude and bandwidth of the intended measurement.
Do not treat MAX362 as a normally closed switch. MAX362 uses four normally open channels, while the related MAX361 family uses normally closed channels. Although the package dimensions can be similar, the inactive signal path is electrically opposite. Review the control truth table, startup state, fault condition, and signal-level requirements before approving either device for a safety-sensitive or fail-state-dependent circuit.
Use a 16-pin through-hole footprint whose drill pattern and pin numbering match the manufacturer package drawing. Confirm the orientation and pin-1 location on the PCB against the actual component marking. Avoid combining a 16-pin PDIP footprint with a surface-mount SOIC variant even when both use 16 terminals, because lead pitch, body size, and assembly method are different.
合规信息
The available product information does not state the requested compliance or material-status classifications. These fields remain unknown rather than being inferred from the package family or producer ordering code.