MCF51JM32EVLK - 32KB Flash ColdFire V1 MCU | NXP | USB & CAN
Référence : MCF51JM32EVLK ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.5 | $9,50 |
| 10 | $8.55 | $85,50 |
| 100 | $7.6 | $760,00 |
| 500 | $6.84 | $3 420,00 |
| 1 000 | $6.08 | $6 080,00 |
MCF51JM32EVLK Présentation
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripheral interfaces into one device. The MCF51JM32 belongs to the 32-bit ColdFire family, which sits in the hierarchy of embedded microcontrollers (MCU -> 32-bit MCU -> ColdFire architecture -> industrial/consumer-grade MCU -> semiconductor IC). ColdFire V1 combines a RISC instruction set with the Freescale/NXP peripheral ecosystem, easing migration from legacy HC08/HCS08 designs.
Key differentiating features include the integrated USB OTG controller with on-chip transceiver - eliminating external PHY chips for low- and full-speed USB designs - and a CAN 2.0A/B-compliant controller targeting industrial networking. The 50 MHz core delivers 50 MIPS, with hardware multiply/accumulate and a background debug controller for non-intrusive in-circuit development.
The architecture combines a ColdFire V1 core with crossbar switch, 32KB program Flash, 16KB SRAM, and a versatile peripheral set: SCI, SPI, I2C, PWM (6 channels), 12-bit ADC (8-ch), and a real-time counter. The on-chip voltage regulator supports 2.7V-5.5V single-supply operation with internal 1.8V core regulation, simplifying board design.
Typical applications include USB peripherals, CAN-based industrial nodes, point-of-sale terminals, medical monitoring devices, and USB-CAN bridges. The integrated USB OTG makes the part a strong fit for HID devices, CDC virtual COM ports, and firmware upgrade dongles.
When designing with this part, ensure the USB DP/DM traces are 90-ohm differential with a common-mode choke nearby; route the 12 MHz crystal traces short and guard them with a ground ring to meet USB compliance. The internal regulator requires a 1uF decoupling capacitor on the VDDINT pin.
Alternatives de remplacement direct pour MCF51JM32EVLK — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MCF51JM32EVLK (même facteur de forme et même empreinte) — différant par Package, Connectivity, Operating Temperature, Program Memory Size, RoHS Status.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MCF51JM64VLK
✅ Remplacement direct✓ En stock
$6.05 / unité
Voir la fiche technique →MCF51JM128VLK
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MCF51JM32EVLK Valeurs maximales et caractéristiques électriques
| Core Processor | ColdFire V1 |
| Core Size | 32-Bit |
| Fréquence d'horloge maximale | 50 MHz |
| Program Memory Size | 32 KB (32K x 8) |
| Program Memory Type | FLASH |
| RAM Size | 16 KB |
| Number of I/O | 66 |
| Connectivity | CAN, I2C, SCI, SPI, USB OTG |
| Peripherals | LVD, PWM, WDT |
| PWM Channels | 6 |
| ADC | 12-bit, 8-channel |
| Tension d'alimentation | 3.3 V / 5 V (2.7 V to 5.5 V range) |
| Température de fonctionnement | -40C to +105C |
| Boîtier | 80-LQFP (14x14 mm) |
| Type de montage | Surface Mount |
Configuration des broches de MCF51JM32EVLK
| Broche 1 | PTE0/TxD1 — Port E bit 0 / SCI1 transmit |
| Broche 2 | PTE1/RxD1 — Port E bit 1 / SCI1 receive |
| Broche 3 | PTE2 — Port E bit 2 |
| Broche 4 | PTE3 — Port E bit 3 |
| Broche 5 | PTE4 — Port E bit 4 |
| Broche 6 | PTE5 — Port E bit 5 |
| Broche 7 | PTE6 — Port E bit 6 |
| Broche 8 | PTE7 — Port E bit 7 |
| Broche 9 | VSS — Ground |
| Broche 10 | VDD — Supply voltage (2.7V-5.5V) |
| Broche 11 | PTF0 — Port F bit 0 |
| Broche 12 | PTF1 — Port F bit 1 |
| Broche 13 | PTF2 — Port F bit 2 |
| Broche 14 | PTF3 — Port F bit 3 |
| Broche 15 | PTF4 — Port F bit 4 |
| Broche 16 | PTF5 — Port F bit 5 |
| Broche 17 | PTF6 — Port F bit 6 |
| Broche 18 | PTF7 — Port F bit 7 |
| Broche 19 | PTG0 — Port G bit 0 |
| Broche 20 | PTG1 — Port G bit 1 |
| Broche 21 | PTG2 — Port G bit 2 |
| Broche 22 | PTG3 — Port G bit 3 |
| Broche 23 | PTG4 — Port G bit 4 |
| Broche 24 | PTG5 — Port G bit 5 |
| Broche 25 | PTG6 — Port G bit 6 |
| Broche 26 | PTG7 — Port G bit 7 |
| Broche 27 | PTH0 — Port H bit 0 |
| Broche 28 | PTH1 — Port H bit 1 |
| Broche 29 | PTH2 — Port H bit 2 |
| Broche 30 | PTH3 — Port H bit 3 |
| Broche 31 | PTH4 — Port H bit 4 |
| Broche 32 | PTH5 — Port H bit 5 |
| Broche 33 | PTH6 — Port H bit 6 |
| Broche 34 | PTH7 — Port H bit 7 |
| Broche 35 | USB_VDDA — USB analog supply (3.3V) |
| Broche 36 | USB_VSSA — USB analog ground |
| Broche 37 | USB_DP — USB D+ data line |
| Broche 38 | USB_DM — USB D- data line |
| Broche 39 | USB_VBUS — USB VBUS detect (5V) |
| Broche 40 | USB_ID — USB OTG ID pin (host/device detect) |
| Broche 41 | CAN_TX — CAN transmit |
| Broche 42 | CAN_RX — CAN receive |
| Broche 43 | VDDA — ADC supply |
| Broche 44 | VSSA — ADC ground |
| Broche 45 | VREFH — ADC reference high |
| Broche 46 | VREFL — ADC reference low |
| Broche 47 | PTA0 — Port A bit 0 |
| Broche 48 | PTA1 — Port A bit 1 |
| Broche 49 | PTA2 — Port A bit 2 |
| Broche 50 | PTA3 — Port A bit 3 |
| Broche 51 | PTA4 — Port A bit 4 |
| Broche 52 | PTA5 — Port A bit 5 |
| Broche 53 | PTA6 — Port A bit 6 |
| Broche 54 | PTA7 — Port A bit 7 |
| Broche 55 | PTB0 — Port B bit 0 |
| Broche 56 | PTB1 — Port B bit 1 |
| Broche 57 | PTB2 — Port B bit 2 |
| Broche 58 | PTB3 — Port B bit 3 |
| Broche 59 | PTB4 — Port B bit 4 |
| Broche 60 | PTB5 — Port B bit 5 |
| Broche 61 | PTB6 — Port B bit 6 |
| Broche 62 | PTB7 — Port B bit 7 |
| Broche 63 | PTC0 — Port C bit 0 |
| Broche 64 | PTC1 — Port C bit 1 |
| Broche 65 | PTC2 — Port C bit 2 |
| Broche 66 | PTC3 — Port C bit 3 |
| Broche 67 | PTC4 — Port C bit 4 |
| Broche 68 | PTC5 — Port C bit 5 |
| Broche 69 | PTC6 — Port C bit 6 |
| Broche 70 | PTC7 — Port C bit 7 |
| Broche 71 | PTD0 — Port D bit 0 |
| Broche 72 | PTD1 — Port D bit 1 |
| Broche 73 | PTD2 — Port D bit 2 |
| Broche 74 | PTD3 — Port D bit 3 |
| Broche 75 | PTD4 — Port D bit 4 |
| Broche 76 | PTD5 — Port D bit 5 |
| Broche 77 | PTD6 — Port D bit 6 |
| Broche 78 | PTD7 — Port D bit 7 |
| Broche 79 | RESET — Reset input (active low) |
| Broche 80 | EXTAL/XOSC — External clock/crystal oscillator input |
Applications typiques
MCF51JM32EVLK convient pour 6 applications: USB Human Interface Devices (HID), CAN-Based Industrial Nodes, USB-to-UART Bridge Dongles, Point-of-Sale Terminals, Medical Monitoring Devices, Firmware Upgrade Dongles.
USB Human Interface Devices (HID)
The MCF51JM32EVLK's integrated USB OTG controller with on-chip transceiver makes it ideal for HID peripherals like keyboards, mice, and game controllers. Its 50 MHz ColdFire V1 core delivers 50 MIPS - enough headroom for HID class drivers, debouncing, and LED animation while leaving Flash budget for vendor-specific extensions. The 32KB Flash fits a typical USB HID stack with composite device support, while 16KB SRAM handles HID report buffers and protocol state. Place a 90-ohm differential DP/DM pair with a common-mode choke near the connector to meet USB 2.0 FS compliance; the internal 1.5 kohm pull-up on D+ enables bus-powered enumeration without external components.
Recommandé
CAN-Based Industrial Nodes
The MCF51JM32EVLK integrates a CAN 2.0A/B-compliant controller with hardware acceptance filtering, ideal for industrial nodes like sensor aggregators and motor controllers on a CANopen or DeviceNet bus. Its 66 GPIO and 6 PWM channels can drive multiple actuators and read quadrature encoders without external logic. The 32KB Flash accommodates CANopen CiA 401/402 profiles for I/O modules; 16KB SRAM is sufficient for CAN transmit/receive buffers and process data objects. Use the on-chip SCI to bridge CAN to RS-485 for legacy systems, or pair with an external CAN transceiver like the TJA1050 for 1 Mbps industrial networks.
Recommandé
USB-to-UART Bridge Dongles
The MCF51JM32EVLK's USB OTG and SCI (UART) peripherals make it a natural fit for USB-to-UART bridge dongles, replacing FTDI FT232 with a programmable NXP solution. The CDC class driver fits comfortably in 32KB Flash, and the on-chip USB transceiver eliminates the external PHY required by discrete bridges. Typical use cases include industrial debug ports, microcontroller firmware upgrade cables, and isolated serial converters. Configure the SCI at 3 Mbps to bridge high-speed UARTs while the USB handles enumeration and suspend/resume with bus-powered operation from VBUS.
Recommandé
Point-of-Sale Terminals
The MCF51JM32EVLK is well-suited for entry-level point-of-sale terminals requiring USB connectivity (for barcode scanners or receipt printers) alongside secure keypad and display interfaces. Its 50 MHz ColdFire V1 core can drive character LCDs and 4x4 keypads while servicing USB interrupt endpoints in real time. The integrated CAN controller supports POS networking to back-office terminals, and the 6 PWM channels can drive buzzer tones for transaction feedback. With 32KB Flash, the part runs a lightweight RTOS or cooperative scheduler handling USB HID + CDC + keypad scanning tasks simultaneously.
Recommandé
Medical Monitoring Devices
The MCF51JM32EVLK suits portable medical monitoring devices that require USB for data upload to a PC (HID or MSD class) plus precision analog measurement. Its 12-bit ADC with 8 channels supports sensor acquisition (temperature, pulse oximetry, or weight sensors) at typical sample rates of 1 kSPS, while the USB OTG transfers patient logs to clinician workstations. The 32KB Flash fits a small embedded OS or state-machine firmware with safety checks, and 16KB SRAM buffers waveform data during USB transfers. The 2.7V-5.5V supply range allows direct battery or USB bus power with no additional regulators.
Recommandé
Firmware Upgrade Dongles
The MCF51JM32EVLK is a strong choice for USB mass storage or HID-based firmware upgrade dongles, where it acts as the bridge between a host PC and a target board's SPI, I2C, or SCI bootloader. The 32KB Flash holds a USB MSD bootloader plus the target communication protocol stack, while the SPI peripheral can directly drive target flash memories at up to half the system clock. Power is supplied entirely from USB VBUS (5V), and the on-chip regulator generates 1.8V for the core, allowing bus-powered operation without external LDOs. Typical throughput reaches 200-300 KB/s for typical SPI flash programming operations.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MCF51JM32EVLK — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MCF51JM64VLK | MCF51JM128VLK | MCF51JM32VFM |
|---|---|---|---|---|
| Package | 80-LQFP (14x14) | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 64-QFP - different |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ColdFire V1, 50 MHz | ColdFire V1, 50 MHz - same | ColdFire V1, 50 MHz - same | ColdFire V1, 50 MHz - same |
| Flash | 32 KB | 64 KB (+100%) | 128 KB (+300%) | 32 KB - same |
| RAM | 16 KB | 16 KB - same | 16 KB - same | 16 KB - same |
| USB OTG | Yes (on-chip transceiver) | Yes (on-chip transceiver) | Yes (on-chip transceiver) | Yes (on-chip transceiver) |
| CAN | Yes (1 controller) | Yes (1 controller) | Yes (1 controller) | Yes (1 controller) |
| GPIO | 66 | 66 - same | 66 - same | 44 (smaller package) |
| Lifecycle | NRND | NRND | Active | NRND |
Principaux différenciateurs
- Integrated USB OTG with on-chip transceiver eliminates external PHY (vs MCF51JM32VFM)
- ColdFire V1 core with hardware MAC and BDM debug (vs MCF51JM128VLK)
- Single-chip CAN + USB OTG combination unique in ColdFire V1 family (vs Cross-brand PIC18F4550)
Notes de conception
Route USB DP/DM as a 90-ohm differential pair with trace length matching within 150 mil. Place a common-mode choke (e.g., ACM2012) within 5 mm of the USB connector, and keep the pair away from switching signals and clocks. Use a ground guard ring around the pair for USB 2.0 FS compliance and EMI margin.
Decouple VDD with a 1uF ceramic + 100nF ceramic pair within 3 mm of the pin. Place a 4.7uF tantalum or ceramic on VDDA to reduce ADC reference noise, and a separate 1uF on USB_VDDA to isolate USB PLL supply. The internal 1.8V regulator on VDDINT requires at least a 1uF low-ESR capacitor; otherwise USB operation may fail at edge temperatures.
Do not exceed 50 MHz bus clock - peripheral timing margins shrink at higher frequencies. The USB_DM/USB_DP pins are 3.3V-only; do not pull them to 5V. The CAN_TX output is TTL-level, requiring an external CAN transceiver (e.g., TJA1050) for actual bus connection - direct CAN bus connection will damage the part.
Informations de conformité
RoHS and lead-free per NXP product documentation. Not AEC-Q100 qualified - not recommended for automotive safety-critical designs. For automotive, contact NXP about Kinetis automotive equivalents.
