MSP430F147IPAG - 8MHz 16-Bit MCU with 32KB Flash | Texas Instruments
Référence : MSP430F147IPAG ✓ ActifMSP430F147IPAG Présentation
A mixed-signal microcontroller integrates digital processing with analog measurement functions on one device. The MSP430F147 belongs to the MSP430F14x mixed-signal MCU family and supports two built-in 16-bit timers, one USART, a fast 12-bit ADC, a comparator, and code- and hardware-compatible family variants. This combination places the device above a basic general-purpose MCU in measurement capability while retaining low-power embedded-control characteristics.
Key features include an 8 MHz maximum clock, 32 KB of Flash program memory, 1 KB of SRAM, 48 I/O pins, and an integrated 12-bit ADC. Two 16-bit timers support timing, capture, compare, and periodic event generation, while the USART and SPI interfaces connect sensors, transceivers, displays, and external data-conversion components. The 64-pin TQFP package also provides more I/O and peripheral connectivity than the smaller members of the MSP430 family.
The MSP430 architecture uses a 16-bit RISC CPU with 16-bit registers and constant generators, which help reduce the number of instructions required for many operations. Its hardware multiplier accelerates multiplication-intensive routines, while the mixed-signal resources allow an analog input to be measured without adding a separate ADC. The device supports operation from 2.5 V or 3.3 V supply configurations, depending on the specific operating conditions and application requirements.
Typical uses include industrial sensor acquisition, low-power measurement instruments, building-control modules, data loggers, and embedded communication equipment. The 12-bit ADC suits applications requiring more resolution than a basic comparator threshold, while two timers and 48 I/O pins simplify peripheral connection and deterministic control. SPI and UART provide practical paths to external sensors, transceivers, memory, and host systems.
PCB design should preserve clean analog grounding near the ADC and comparator while routing digital clock and switching signals away from sensitive inputs. External bypass capacitors should be placed close to the supply pins, and unused I/O pins should be configured according to the manufacturer datasheet. Firmware and peripheral assignments should be checked against the exact device variant before production release.
This product page combines the key electrical specifications, package information, application guidance, comparison parameters, and practical design considerations needed to evaluate the MSP430F147IPAG. It also distinguishes direct family alternatives from functions that are merely similar, helping engineers make a package-, memory-, and peripheral-compatible selection decision.
Alternatives de remplacement direct pour MSP430F147IPAG — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MSP430F147IPAG (même facteur de forme et même empreinte) — différant par ADC Resolution, Flash Memory, Package, SRAM, Architecture.
MSP430F148IPAG
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MSP430F1481IPAG
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MSP430F1471IPAG
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MSP430F149IPAG
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MSP430F1491IPAG
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MSP430F147IPAG Valeurs maximales et caractéristiques électriques
| Product Type | 16-bit mixed-signal microcontroller |
| CPU Architecture | MS430X RISC |
| Fréquence d'horloge maximale | 8 MHz |
| Flash Memory | 32 KB (32K x 8 + 256 B) |
| SRAM | 1 KB |
| ADC Resolution | 12 bit |
| ADC Architecture | 12-bit successive approximation |
| Comparator Count | 1 |
| Timer Count | 2 x 16-bit timers |
| USART Count | 1 |
| SPI Interface | 1 |
| General-Purpose I/O Pins | 48 |
| Tension d'alimentation | 2.5 V or 3.3 V |
| Plage de température de fonctionnement | -40°C to +85°C |
| Boîtier | 64-pin TQFP (PAG), 10 mm x 10 mm |
| Type de montage | Surface mount |
Guide de configuration des broches du MSP430F147IPAG 64-pin tqfp (pag), 10 mm x 10 mm
Configuration des broches du MSP430F147IPAG (boîtier 64-pin tqfp (pag), 10 mm x 10 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour MSP430F147IPAG.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MSP430F147IPAG convient pour 6 applications: Industrial Sensor Acquisition, Low-Power Measurement Instrument, Building Automation Controller, Data Logger and Portable Recorder, Communication and Serial Interface Module, Embedded Motor and Process Control.
Industrial Sensor Acquisition
The MSP430F147IPAG fits industrial sensor acquisition because its 12-bit ADC can digitize analog inputs while the 8 MHz 16-bit processor handles filtering, scaling, and control functions on the same device. Two 16-bit timers support timed sampling, while 48 I/O pins connect sensors, alarm signals, and discrete actuators. The 2.5 V or 3.3 V supply configurations accommodate compact embedded instrumentation, and the UART provides a direct path to a host or supervisory controller. For accurate measurements, use separate analog and digital grounding strategies, condition high-impedance sensor sources, and verify the ADC input range and acquisition timing against the manufacturer datasheet.
Recommandé
Low-Power Measurement Instrument
The MSP430F147IPAG is suitable for portable measurement instruments that combine low-power operation with an integrated analog front end. Its 16-bit RISC core, 16-bit registers, constant generators, and hardware multiplier support efficient signal-processing routines, while the 12-bit ADC removes the need for a separate converter in many designs. The 1 KB SRAM supports buffering and real-time calculations, and the USART or SPI interface can connect to a display, external memory, or radio module. Power architecture should account for the selected operating mode because the ADC, timers, communication interfaces, and CPU clock determine the actual current draw.
Recommandé
Building Automation Controller
The MSP430F147IPAG supports building-automation nodes that monitor analog inputs and control discrete outputs in a compact controller. Its 48 I/O pins can accommodate digital sensors, relay-control outputs, status indicators, and communication interfaces, while the integrated 12-bit ADC handles temperature, occupancy, or air-quality sensor inputs. Two hardware timers improve repeatability for periodic measurement and control tasks, and the 64-pin TQFP package simplifies access to the available I/O. In this application, keep relay drivers and inductive loads away from the ADC region, provide local regulation for noisy loads, and validate the controller's watchdog and brownout behavior during power transitions.
Recommandé
Data Logger and Portable Recorder
The MSP430F147IPAG can serve as the controller in a compact data logger that samples analog inputs and transfers records through a serial link. The 12-bit ADC and two timers establish a predictable measurement sequence, while the hardware multiplier accelerates common scaling and filtering operations on the 16-bit CPU. SPI can connect to serial flash or an external sensor, and the USART can provide a simple connection to a host computer or radio module. Because SRAM is limited to 1 KB, use buffering or external storage when acquisition bursts exceed internal memory. Design a low-power retention strategy and use the family datasheet to configure the clock, ADC, and unused pins correctly.
Recommandé
Communication and Serial Interface Module
The MSP430F147IPAG is appropriate for a communication module that must combine local control with serial connectivity. Its USART supports host or peripheral communication, SPI enables connection to sensors, transceivers, or external storage, and two timers can generate timing events or service protocol intervals. The 8 MHz 16-bit processor provides enough performance for framing, checksums, buffering, and supervisory logic, while 48 I/O pins provide status and configuration signals. At 2.5 V or 3.3 V, the controller can operate near low-voltage radio and sensor subsystems, although interface voltage levels must be checked. Use controlled impedance routing for high-speed signals and keep switching-current return paths separate from ADC references.
Recommandé
Embedded Motor and Process Control
The MSP430F147IPAG can supervise low-power process-control or motor-control subsystems when a dedicated motor driver is not required. Two 16-bit timers support PWM generation, input capture, and period-based control, while the 12-bit ADC provides feedback from temperature, pressure, position, or current-sensing networks. Its 48 I/O pins allow direct connection of encoders, fault signals, gate-control lines, and communication peripherals. The hardware multiplier improves the efficiency of proportional-integral-derivative and other multiply-intensive control calculations. Keep high-current switching stages separate from the MCU supply and analog ground, add appropriate gate-driver protection, and verify timing margins because 8 MHz CPU operation and peripheral synchronization determine the achievable control-loop rate.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MSP430F147IPAG — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MSP430F148IPAG | MSP430F1481IPAG | MSP430F1471IPAG | MSP430F149IPAG | MSP430F1491IPAG |
|---|---|---|---|---|---|---|
| Package | 64-pin TQFP (PAG), 10 mm x 10 mm | 64-pin TQFP (PAG), 10 mm x 10 mm | 64-pin TQFP (PAG), 10 mm x 10 mm | 64-pin TQFP (PAG), 10 mm x 10 mm | 64-pin TQFP (PAG), 10 mm x 10 mm | 64-pin TQFP (PAG), 10 mm x 10 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Clock Frequency | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz |
| CPU Architecture | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 64 KB | 64 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 2 KB | 2 KB |
| ADC Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| General-Purpose I/O Pins | 48 | 48 | 48 | 48 | 48 | 48 |
| Timer Configuration | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers |
Principaux différenciateurs
- Provides closely matched family alternatives without changing the PCB footprint (vs MSP430F148IPAG)
- Offers a direct memory-capacity upgrade within the same family architecture (vs MSP430F149IPAG)
- Combines a 12-bit ADC with two hardware timers and 48 I/O pins (vs MSP430F1471IPAG)
- Uses an industrial-temperature 64-pin TQFP package for mixed-signal designs (vs MSP430F1481IPAG)
Notes de conception
Treat the analog and digital sections of the PCB as separate return domains until they meet at the device ground structure. Place input-conditioning components near the ADC pins, keep high-current switching paths away from the measurement area, and route the ADC reference through a quiet section of the board. The 12-bit converter can resolve meaningful data only when supply noise, reference variation, source impedance, and PCB coupling do not dominate the input signal.
Design the 2.5 V or 3.3 V supply for the maximum CPU, ADC, timer, and interface activity rather than a sleep-state estimate. Place local bypass capacitors directly beside the appropriate supply pins and route them with short, low-impedance connections. Check brownout behavior, startup sequencing, and regulator headroom against the family datasheet. The 1 KB SRAM also makes it important to avoid interrupt-driven workloads that create excessive stack depth.
Do not assume that another 64-pin MCU is interchangeable solely because its package dimensions match. MSP430 firmware depends on the RISC instruction set, memory map, interrupt vectors, peripherals, and pin multiplexing. When moving from MSP430F147IPAG to an F14x or F14x1 alternative, review register definitions, ADC behavior, timer assignments, port functions, clock setup, startup code, and any application-specific timer or UART assumptions.
Use the SPI and USART interfaces according to the electrical characteristics and timing specified by the manufacturer. For SPI, keep the clock and data routes short, provide a defined return path, and account for signal integrity at the selected clock rate. For the UART, verify logic levels, baud-rate tolerance, and whether the selected interface pins conflict with ADC inputs. Avoid assigning critical communications to pins that would otherwise support higher-value analog functions.
Informations de conformité
The manufacturer product page identifies the MSP430F147IPAG as an industrial-temperature device, but no explicit environmental or material-compliance declaration is shown for this exact ordering code.