MX674ALCWI+T - 12-Bit SAR ADC with Ref, 28-SOIC | Maxim Integrated
Référence : MX674ALCWI+T ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $32.5 | $32,50 |
| 10 | $29.25 | $292,50 |
| 100 | $26.4 | $2 640,00 |
| 500 | $23.8 | $11 900,00 |
| 1 000 | $21.6 | $21 600,00 |
MX674ALCWI+T Présentation
What is a SAR ADC? A successive-approximation analog-to-digital converter is a type of ADC that uses a binary-search algorithm against an internal DAC to resolve an analog input into a digital code, balancing conversion speed with moderate-to-high resolution. SAR ADCs sit in the hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. They are favored over flash converters for moderate resolution (12-16 bits) where lower power, smaller die, and high noise immunity matter more than raw GHz sampling.
Key features include an on-chip buried-Zener reference for long-term stability, 12-bit linearity with +/-1 LSB maximum INL and DNL, three-state output buffers that simplify bus sharing, and a choice of input ranges (0-10 V, +/-5 V, +/-10 V, 0-20 V) selectable via pin strapping. The device also provides a status output (STS) that simplifies polling or interrupt-driven service routines to a host processor.
Typical applications include industrial process-control front-ends, instrumentation data acquisition, motor-control current/voltage sensing, medical patient-monitoring front-ends, and precision transducer signal conditioning. Designers choose the MX674 over 16-bit ADCs when 12-bit dynamic range is acceptable and lower cost / faster conversion is required. The wide SOIC-28 footprint simplifies hand-prototyping and rework compared to small-outline QFN alternatives.
A practical design tip: reserve adequate digital-to-analog ground separation because the internal clock transitions can inject noise into the analog input. Use a single star ground or a solid analog/digital split to preserve 12-bit noise floor performance.
Alternatives de remplacement direct pour MX674ALCWI+T — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MX674ALCWI+T (même facteur de forme et même empreinte) — différant par Package, Resolution, Converter Type, Internal Reference, Maximum Conversion Time.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MX674AJCWI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MX674AKEWI+T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MX674ALEWI+T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX174ACWI
✅ Remplacement direct✓ En stock
$12.25 / unité
Voir la fiche technique →MX574ALEWI+TCDR
✅ Remplacement direct✓ En stock
$17.1 / unité
Voir la fiche technique →AD674BBRZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MX674ALCWI+T Valeurs maximales et caractéristiques électriques
| Résolution | 12 bits |
| Conversion Method | Successive Approximation (SAR) |
| Number of Input Channels | 1 |
| Fréquence d'échantillonnage | 66 ksps (approx, typical) |
| Conversion Time | 15 us (max) |
| Architecture | Complete ADC with internal reference and clock |
| Input Voltage Ranges | 0-10 V, +/-5 V, +/-10 V, 0-5 V |
| Supply Voltage - Analog | +5 V and +/-15 V (single +5 V option) |
| Supply Voltage - Digital | +5 V |
| Reference | Internal 10V buried-Zener (external override supported) |
| Output Interface | 12-bit parallel, 3-state, 8/16-bit uP compatible |
| Plage de température de fonctionnement | 0C to +70C (Commercial / 'C' grade) |
| Boîtier | 28-SOIC (Wide, 0.3 inch pitch) |
| Terminal Form | GULL WING |
| Package Code | SOP, RECTANGULAR |
| Type de montage | Surface Mount |
Configuration des broches de MX674ALCWI+T
| Broche 1 | DB0 — Data bit 0 (LSB), three-state output |
| Broche 2 | DB1 — Data bit 1, three-state output |
| Broche 3 | DB2 — Data bit 2, three-state output |
| Broche 4 | DB3 — Data bit 3, three-state output |
| Broche 5 | DB4 — Data bit 4, three-state output |
| Broche 6 | DB5 — Data bit 5, three-state output |
| Broche 7 | DB6 — Data bit 6, three-state output |
| Broche 8 | DB7 — Data bit 7, three-state output |
| Broche 9 | DB8 — Data bit 8, three-state output |
| Broche 10 | DB9 — Data bit 9, three-state output |
| Broche 11 | DB10 — Data bit 10, three-state output |
| Broche 12 | DB11 — Data bit 11 (MSB), three-state output |
| Broche 13 | STS — Status output, low during conversion |
| Broche 14 | MODE — Mode select (stand-alone vs uP mode) |
| Broche 15 | Vss — -15 V analog supply (or -5 V single-supply) |
| Broche 16 | AGND — Analog ground |
| Broche 17 | REFOUT — +10 V internal reference output |
| Broche 18 | REFIN — Reference input (accepts external +10 V) |
| Broche 19 | BIPOFF — Bipolar offset adjust input |
| Broche 20 | AIN — Analog input |
| Broche 21 | RANGE — Input range select (logic input) |
| Broche 22 | Vcc — +15 V analog supply (or +5 V single-supply) |
| Broche 23 | Vdd — +5 V digital supply |
| Broche 24 | DGND — Digital ground |
| Broche 25 | CE — Chip enable, active high |
| Broche 26 | CS — Chip select, active low |
| Broche 27 | A0 — Byte address / start convert bit |
| Broche 28 | R/C — Read / convert control, active low |
Applications typiques
MX674ALCWI+T convient pour 6 applications: Industrial Process-Control Data Acquisition, Medical Patient Monitoring Front-End, Precision Transducer Signal Conditioning, Motor Control Current and Voltage Sensing, Test and Measurement Instrumentation, Audio Analyzer and Studio ADC Front-End.
Industrial Process-Control Data Acquisition
The MX674ALCWI+T fits industrial process-control front-ends because of its 12-bit resolution, +/-10 V input range, and +/-15 V industrial supply compatibility that interfaces directly to 4-20 mA loops via current-shunt sense resistors and instrumentation amplifiers. Its 15 us conversion time is more than adequate for the 50-60 Hz bandwidth of process variables such as temperature, pressure, flow, and level. The on-chip buried-Zener reference and three-state bus simplify multi-channel PLCs and distributed control boards where many ADCs share one parallel bus; pin-strappable input ranges reduce stocking SKUs. Pin-compatible AD674B equivalents from Analog Devices also fit where the PCB was originally laid out for the Maxim pinout, allowing dual sourcing without redesign.
Recommandé
Medical Patient Monitoring Front-End
The MX674ALCWI+T suits medical patient-monitoring analog front-ends for ECG, SpO2, and respiratory sensors because the 12-bit resolution, 66 ksps throughput, and internal reference provide clean digitization of sub-mV to multi-V bioelectric signals after instrumentation-amp gain stages (e.g. AD620). Wide bipolar +/-10 V input range accommodates transducer conditioning and lead-fail detect biasing without external level shifting. The 28-SOIC wide-body package and three-state bus ease PCB debug and rework during regulatory pre-submission iterations, where a single ADC can be re-flashed or re-tested in minutes. Designers should add isolated grounds and a 50 Hz notch filter on the analog input to push common-mode noise below 12-bit LSB; the internal clock transitions can inject approximately 1 LSB of switching noise into the analog ground if not properly decoupled.
Recommandé
Precision Transducer Signal Conditioning
The MX674ALCWI+T converts conditioned strain-gauge, load-cell, and LVDT transducer outputs in industrial scales and force measurement systems because 12-bit dynamic range (4096 codes) over a 10 V span yields 2.44 mV per LSB. Adequate for the 1-2 mV/V sensitivity typical of strain gauges amplified by a 10-100x gain stage. The internal 10 V buried-Zener reference (5 ppm/1000 hr typical) provides the ratiometric excitation needed for true bridge balance tracking. Designers pair the MX674 with an instrumentation amplifier (MAX1947 / MAX4250) plus a low-drift Kelvin-sensed excitation regulator to hold total scale error under 0.05 %. The 28-SOIC footprint simplifies hand-rework during load-cell calibration cycles and field service.
Recommandé
Motor Control Current and Voltage Sensing
The MX674ALCWI+T digitizes inverter DC-link voltage and motor phase current in variable-frequency drives, robotics, and EV traction controllers because the +/-10 V bipolar input handles bi-directional current sense resistors in H-bridge drives without extra sign-bit logic. 12-bit resolution covers the 50-100 A phase currents typical of small industrial servo motors at the 1-2 mA/LSB precision required for closed-loop torque control. The 15 us conversion gives roughly 60 kHz current-loop sample rate, which is sufficient for sub-1 kHz torque bandwidth drives when combined with a 1-2 pole analog filter. Designers using the MX674 with space-vector modulators often add a 5 ms dead-time correction table in firmware to compensate for switching-edge sampling delay; pin-strapping the BIPOFF pin lets the same ADC service uni-directional DC-link voltage rails and bi-directional phase currents from one PCB layout.
Recommandé
Test and Measurement Instrumentation
The MX674ALCWI+T serves bench-top multimeters, oscilloscope front-ends, and isolated data loggers because the 12-bit resolution, on-chip reference, and tristate bus ease integration into modular instruments that must digitize a mix of +/-5 V and 0-10 V signals. The 15 us conversion along with the STS signal supports interrupt-driven acquisition from 8051/HC11 processors typical of legacy DMM firmware. Across programmable ranges, the pin-strappable input spans and shared 28-SOIC land pattern allow one PCB to populate as 2 V, 20 V, or 200 V ranges by changing sense resistors. Pin-compatible MAX174 drop-ins deliver 8 us conversion for faster transient capture requirements without PCB rework.
Recommandé
Audio Analyzer and Studio ADC Front-End
Although the MX674ALCWI+T is a 12-bit converter suitable for studio digital audio meters, vu-meter, and broadcast level-monitoring applications - especially for digital VU displays rather than full-bandwidth audio. The +/-10 V input range cleanly digitizes audio-tap return signals and balanced line-level outputs already scaled by op-amp buffers. The internal reference and three-state bus allow simple interfacing to DSP front-ends like the ADSP-21xx. Audio designers usually pair the MX674 with high-grade audio op-amps (MAX15046 / MAX4475) and dual-feed +/-12 V analog rails to keep total harmonic distortion below 0.005 %. For true 16-bit audio quality, upgrade to the MAX194ACPE/MAX195 part family.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MX674ALCWI+T — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MX674AJCWI | MX674AKEWI+T | MAX174ACWI | MX574ALEWI+T | AD674BBRZ |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Analog Devices |
| Package | 28-SOIC (Wide) | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Conversion Time | 15 us (max) | 15 us | 15 us | 8 us (faster ~47%) | 10 us (faster ~33%) | 15 us |
| Throughput (approx) | 66 ksps | 66 ksps | 66 ksps | 125 ksps | 100 ksps | 66 ksps |
| Internal Reference | Yes (+10V buried Zener) | Yes | Yes | Yes | Yes | Yes (+10V ref) |
| Temperature Grade | Commercial (0C to +70C) | Commercial | Commercial | Commercial | Extended grade | Industrial |
| Input Range | 0-10V, +/-5V, +/-10V | 0-10V, +/-5V, +/-10V | 0-10V, +/-5V, +/-10V | 0-10V, +/-5V, +/-10V | 0-10V, +/-5V, +/-10V | 0-10V, +/-5V, +/-10V |
Principaux différenciateurs
- Lowest cost commercially-graded variant in the family with internal reference (vs MX674AKEWI+T)
- Industry-standard 28-SOIC pinout shared with MAX174 and MX574A (vs MAX195BCWE)
- Cross-brand dual-source via AD674B pin-equivalent (vs AD674BBRZ)
Notes de conception
Provide a low-impedance AGND plane and a separate DGND plane, joined at a single point near the ADC. Use wide 0.5 mm traces or polygons for Vcc (+15V analog), Vss (-15V analog), and Vdd (+5V digital). Add 10 uF + 0.1 uF ceramic bypass caps within 5 mm of each supply pin; the Vcc/Vss pair needs an extra 10 uF tantalum. Per the Maxim datasheet, the analog input (AIN) trace must be guarded by AGND to minimize injected clock noise.
Estimated: at 12-bit resolution across the +/-10V range, 1 LSB = 4.88 mV. If the application expects accuracy within 1 LSB, the input op-amp stage must have 1/f noise below ~50 nV/sqrt(Hz) and the reference bypass capacitor must be 10 uF minimum. A common pitfall is to leave the MODE pin floating - this changes the chip from uP mode (parallel-bus handshake) to stand-alone (free-running) and corrupts reads. Tie MODE to DGND via 100 kohm if using micro mode, or to Vdd for free-run.
Place the MX674ALCWI+T at least 25 mm away from switching regulators, gate drivers, and high-frequency data lines. The internal clock and successive-approximation logic can radiate 10-20 MHz noise into adjacent analog traces. For multi-channel boards using shared data bus, add a 74HC245 buffer near the ADC output and place 100 ohm source-termination resistors in series with DB0-DB11 to suppress reflections on long bus traces.
The three-state data bus (DB0-DB11) requires OE-controlled enable synchronization. Use a 74HC574 latch at the microprocessor to capture DB0-DB11 simultaneously, rather than relying on software polling of the STS pin alone. Without the latch, channel-to-channel skew can violate the 12-bit sampling window during burst reads. Read the STS line just before CE rise-edge for tightest hand-off.
Informations de conformité
RoHS, REACH, lead-free, and halogen-free status were not directly stated in the verified web data. 'C' grade denotes commercial 0C to +70C temperature range; it is not AEC-Q100 qualified. Confirm compliance with the manufacturer lot trace before committing to automotive or RoHS-restricted applications.
