Texas Instruments

OPA2227U - Dual 8 MHz Low-Noise Precision Op Amp | TI

Référence : OPA2227U ✓ Actif
8-SOIC (0.154 inch, 3.90 mm width) Package
MOQ : 1 |

OPA2227U Présentation

Texas Instruments OPA2227U is a dual high-precision, low-noise operational amplifier designed for instrumentation and precision signal-chain applications. The device provides two amplifier channels, an 8 MHz gain-bandwidth product, and an 8-SOIC package. Its combination of low noise, precision DC performance, and wide bandwidth makes it suitable for sensor amplification, current measurement, data conversion, and precision control systems.

An operational amplifier is a voltage-gain circuit used in the broader amplifier and analog IC hierarchy. OPA2227U belongs to the precision operational-amplifier family, where accurate input-offset behavior, low-noise performance, and stable operation under real-world feedback networks are more important than maximum bandwidth alone. Each of its two channels can operate independently, allowing two related analog functions to share one package.

Key features include two precision amplifier channels, an 8 MHz gain-bandwidth product, and operation from negative to positive supply rails. The wide common-mode and output ranges make the device suitable for bipolar and single-supply signal chains when supply levels and input ranges permit. Low-noise operation improves the usable resolution of low-level sensor signals, while the 8 MHz bandwidth supports accurate dynamic signal handling.

OPA2227U belongs to the TI OPAx227 family of high-precision, low-noise operational amplifiers. The family combines low-noise input stages with precision DC characteristics and wide bandwidth. That balance is useful when one amplifier must perform both slow, accurate measurements and moderate-frequency signal amplification without moving to a separate precision and fast-amplifier architecture.

Typical uses include bridge-sensor front ends, low-level current sensing, analog-to-digital converter drive circuits, precision filter stages, laboratory instrumentation, and industrial control. In each case, resistor matching, input bias current, noise, and output swing determine whether the circuit achieves its intended accuracy. Stable reference and feedback components are particularly important when the design seeks microvolt-level or high-resolution measurement performance.

PCB implementation requires short feedback paths and careful grounding to preserve low-noise performance. Place input and feedback components close to the relevant amplifier pins, keep high-impedance nodes away from switching nodes, and provide adequate output-current margin when driving capacitive loads. The SOIC-8 outline supports conventional surface-mount assembly, but exposed thermal performance is not the primary constraint for this linear device.

This product page combines the OPA2227U ordering information, package details, sourcing guidance, compatible-part assessment, and application-oriented design guidance. It also organizes comparisons and replacement questions around the practical constraints engineers face when reusing an existing 8-SOIC precision-amplifier layout.

Alternatives de remplacement direct pour OPA2227U — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

OPA2227UA

✅ Remplacement direct
📦 8-SOIC
Same dual OPA2227 family and 8-SOIC footprint; ordering/qualification suffix differs, so temperature grade and exact electrical limits require confirmation

📋 Alternative de référence (hors catalogue)

OPA2227U Valeurs maximales et caractéristiques électriques

Amplifier Type Dual precision operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 8 MHz
Boîtier 8-SOIC (0.154 inch, 3.90 mm width)
Plage de température de fonctionnement -40 °C to +85 °C
Type de montage Surface mount

Guide de configuration des broches du OPA2227U 8-soic (0.154 inch, 3.90 mm width)

Configuration des broches du OPA2227U (boîtier 8-soic (0.154 inch, 3.90 mm width)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 8-soic (0.154 inch, 3.90 mm width) pour le OPA2227U

Aucune donnée de brochage détaillée disponible pour OPA2227U.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

OPA2227U convient pour 6 applications: Bridge Sensor Signal Conditioning, Precision Current Measurement, High-Resolution ADC Driver, Laboratory Instrumentation, Precision Active Filtering, Industrial Process Control.

🏭

Bridge Sensor Signal Conditioning

OPA2227U suits bridge-sensor front ends where low-level differential signals must be amplified accurately without adding excessive noise. Its two precision channels can form the two halves of an instrumentation arrangement or handle two related sensor channels, while the 8 MHz gain-bandwidth product provides more bandwidth than a strictly DC-oriented amplifier. The gain network should use low-temperature-coefficient resistors, and the input arrangement must account for input bias current and source impedance to prevent offset errors.

⚡

Precision Current Measurement

OPA2227U can amplify the small voltage generated across a low-value shunt resistor in power-monitoring and laboratory systems. Its low-noise operational-amplifier characteristics help preserve resolution, while the two channels allow complementary measurement or gain stages when their functions are compatible. The shunt resistance, amplifier input offset, and Kelvin routing determine the smallest detectable current; keep the shunt and amplifier inputs away from switching currents to avoid common-mode and ground disturbances.

📡

High-Resolution ADC Driver

OPA2227U is appropriate for drive and buffering stages ahead of high-resolution converters when the selected ADC input requires a low-noise, high-impedance amplifier. Its 8 MHz gain-bandwidth product supports signal bandwidth beyond basic precision-DC operation, and the dual configuration can drive or monitor two converter channels. Correct drive stability depends on the ADC input network, including isolation resistance and capacitance, so validate the complete transient response rather than relying only on the 8 MHz figure.

🧰

Laboratory Instrumentation

OPA2227U fits laboratory amplifiers, programmable-gain stages, and precision measurement instruments requiring low-noise signal conditioning. Two channels can reduce component count in instruments that measure one quantity while monitoring a reference or control signal. The device's precision-focused family characteristics are useful for slow-to-moderate bandwidth signals, but input protection, offset nulling strategy, reference quality, and resistor matching must be designed around the actual source impedance and measurement range.

🔧

Precision Active Filtering

OPA2227U can implement active low-pass or band-pass stages where accurate gain and low added noise are important. Its 8 MHz gain-bandwidth product allows useful operating bandwidth for moderate-frequency filtering, while precision DC behavior helps maintain filter accuracy near the passband. Component tolerances dominate passive-filter accuracy in many implementations, so select matched resistors and capacitors and evaluate the closed-loop response across temperature and output-loading conditions.

🏭

Industrial Process Control

OPA2227U is suitable for low-level process-signal conditioning in industrial monitoring and control systems, including pressure, temperature, and strain inputs. The dual package provides two channels for closely related measurements while keeping the analog path compact. Industrial systems can present large transients and shared-ground disturbances, so add input protection, maintain high-impedance routing, isolate analog and digital return currents, and verify supply behavior during actuator transitions before using the amplifier near switching equipment.

What is the operating voltage range of the OPA2227U?
The OPA2227U is a dual precision operational amplifier intended for operation from negative and positive supply rails, but the exact minimum and maximum supply voltages should be confirmed in the manufacturer datasheet before design release. The OPAx227 family is specified for operation over -40 °C to +85 °C, and the OPA2227U is packaged in an 8-SOIC outline. Use the Recommended Operating Conditions table to verify rail limits for the selected operating temperature.
What is the bandwidth of the OPA2227U?
The OPA2227U has an 8 MHz gain-bandwidth product. This figure describes the closed-loop bandwidth for a given noise-gain setting and should not be treated as independent of feedback topology. According to the Texas Instruments OPA2227 family description, the series combines low noise, wide bandwidth, and high precision. The 8 MHz specification supports moderate-frequency instrumentation while preserving the DC accuracy needed by precision measurement circuits.
Is the OPA2227U a single or dual operational amplifier?
The OPA2227U contains two independent operational-amplifier channels in one 8-SOIC package. DigiKey identifies the exact ordering code as a two-circuit, 8-SOIC amplifier, while the Texas Instruments product page describes the OPA2227 as a dual high-precision, low-noise operational amplifier. This makes it suitable for two related analog channels that can share common supply and ground connections.
Where can I download the OPA2227U datasheet PDF?
The official OPA2227 documentation is available from Texas Instruments at https://www.ti.com/lit/gpn/OPA2227, and the manufacturer product page is https://www.ti.com/product/OPA2227. The datasheet contains the pin configuration, electrical characteristics, typical performance curves, ordering information, and package drawings. Download the manufacturer document before assigning PCB pads or relying on a third-party copy for production design controls.
Where can I find the OPA2227U pinout?
The OPA2227U pinout is shown in the pin-configuration section of the Texas Instruments OPA2227 datasheet. The component uses an 8-SOIC package with two complete operational-amplifier channels. Assign the footprint from the manufacturer package drawing rather than inferring connections from a generic SOIC outline, and verify the exposed electrical connections against the ordering-code suffix used on the assembled board.
What can replace the OPA2227U on the same 8-SOIC footprint?
The closest identified drop-in option is the Texas Instruments OPA2227UA, which uses the same 8-SOIC device family and appears in direct replacement comparisons. However, fewer than five defensible drop-in alternatives were identified without padding the list with reel-code or packaging-only variants. Before substitution, compare the complete electrical tables, especially supply range, offset voltage, bias current, input bias-current compensation, noise, and common-mode range.
Is the OPA2227U suitable for low-level sensor measurement?
Yes, the OPA2227U is suitable for low-level sensor measurement because it is a high-precision, low-noise dual operational amplifier with an 8 MHz gain-bandwidth product. Its two channels can amplify related bridge, current, or differential sensor signals while sharing one package. The final measurement resolution also depends on sensor source impedance, reference accuracy, resistor tolerance, input bias current, and PCB leakage, so the complete analog chain must be analyzed.
How does the OPA2227U compare with OPA227U?
The OPA227U is a single-channel member of the same TI precision, low-noise amplifier family, while the OPA2227U provides two channels in an 8-SOIC package. They are therefore not pin-for-pin equivalents in an existing dual-amplifier layout despite sharing family characteristics. The OPA2227U is the appropriate choice when both amplifier channels must fit one 8-pin footprint; the single OPA227U requires a different package arrangement.
When should I choose the OPA2227U over a general-purpose dual op amp?
Choose the OPA2227U when the signal path requires a deliberate balance of low noise, precision DC behavior, and an 8 MHz gain-bandwidth product. A general-purpose dual amplifier may be appropriate for ordinary logic-level signal conditioning, but it can introduce more noise or offset error than desired in high-resolution measurement paths. The OPA2227U is preferable when two precision channels can share an 8-SOIC footprint and its operating range fits the design.
What design considerations matter for the OPA2227U low-noise performance?
The OPA2227U should be placed close to the source and feedback components so that interference is minimized before reaching sensitive amplifier inputs. Keep high-impedance input and feedback nodes away from switching-regulator traces, clocks, and digital return currents. Use a clean analog ground strategy and stable, low-noise references. Because the package has no exposed thermal pad, thermal limits relate primarily to total device dissipation and board copper rather than heat-sink mounting.
Where can I buy the OPA2227U and check its current availability?
Use the Request a Quote form on this page to request the OPA2227U, current availability, lead time, and order quantities from XAIPART. The exact manufacturer ordering code is OPA2227U in an 8-SOIC package. Because inventory and commercial terms can change quickly, obtain a written quotation for the required quantity rather than relying on a static listing snapshot.
How much does the OPA2227U cost?
Current OPA2227U pricing is presented through the Request a Quote form on this page. The commercial response should account for the exact 8-SOIC ordering code, requested quantity, and packaging requirements. Request a formal quotation for production planning and avoid treating an isolated marketplace price as a guaranteed volume price, since component pricing and availability can change by quantity and market condition.
Is the OPA2227U in stock and what is its lead time?
Current stock and lead time for OPA2227U should be requested through the Request a Quote form on this page. One distributor listing reported 38,376 pieces immediately available, but that snapshot does not guarantee allocation, future stock, or a delivery commitment. Provide the required quantity and target date in the request so the response can reflect current procurement conditions.
What are the key specifications of the OPA2227U that engineers should know?
The OPA2227U is a dual high-precision, low-noise operational amplifier with two channels, an 8 MHz gain-bandwidth product, an 8-SOIC package, and an operating-temperature specification of -40 °C to +85 °C. It belongs to the TI OPAx227 family, which combines precision DC performance with low noise and wide bandwidth. Supply limits, offset voltage, bias current, noise density, slew rate, and output swing must be taken from the manufacturer electrical-characteristics tables.
What is the best Texas Instruments equivalent for the OPA2227U?
The best identified Texas Instruments drop-in candidate is the OPA2227UA because it is the same dual OPA2227 family in an 8-SOIC package and is explicitly compared with OPA2227U as a replacement candidate. It does not represent a separate competitor design; it is an ordering and qualification variant of the same device family. Confirm its exact orderable status, temperature grade, and complete electrical limits before approving it for production.

Données de référence d'ingénierie pour OPA2227U — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose OPA2227U when the design needs two high-precision, low-noise amplifier channels in an 8-SOIC package and the closed-loop bandwidth remains comfortably below the 8 MHz gain-bandwidth product. It is well suited to bridge sensors, low-level current measurement, laboratory instrumentation, precision filters, and ADC signal conditioning where added noise or offset would reduce measurement quality. OPA227U is not a drop-in choice for that arrangement because it is a single amplifier. OPA2227UA is the closest identified same-family alternative and can be considered when its exact ordering grade and electrical limits satisfy the application. For designs needing wider bandwidth, rail-to-rail operation, lower offset, or different noise-versus-power performance, select a different amplifier family after comparing the complete electrical tables rather than assuming that a matching package guarantees equivalent behavior.

Comparaison avec les alternatives

Paramètre Ce produit OPA2227UA
Brand Texas Instruments Texas Instruments
Package 8-SOIC (0.154 inch, 3.90 mm width) 8-SOIC
Amplifier Configuration Dual Dual
Number of Channels 2 channels 2 channels
Mounting Type Surface mount Surface mount

Principaux différenciateurs

  • Combines two precision channels in one 8-SOIC package (vs OPA227U)
  • Provides an 8 MHz gain-bandwidth product for precision signal conditioning (vs OPA2227UA)
  • Supports two related measurement functions in one footprint (vs OPA227U)

Notes de conception

Place feedback resistors, input resistors, and compensation capacitors directly beside their associated OPA2227U pins. Keep the two channels physically separated when one channel handles a sensitive low-level input and the other drives a faster or switching-related signal. Route high-impedance input and feedback nets as short traces over a quiet ground plane, and avoid placing them beneath digital clock lines, regulator switches, or connectors with rapidly changing return currents.

Do not assume that two amplifiers in one package have identical DC behavior. For matched channels, verify offset-voltage and bias-current matching in the manufacturer tables and include resistor and reference tolerances in the error budget. The common eight-SOIC package also limits available pins, so nulling or external compensation options must match the chosen configuration. Confirm the selected OPA2227 ordering suffix before applying a circuit designed around another member of the family.

The 8 MHz gain-bandwidth product does not guarantee a flat 8 MHz response at every closed-loop gain. High closed-loop gains reduce available bandwidth, and capacitive loading can impair stability. Place an isolation resistor between the amplifier and unusually capacitive loads, evaluate the complete feedback network with an oscilloscope, and reserve additional layout space for input filtering or compensation when driving long cables, multiplexers, or successive-approximation ADC inputs.

Use a low-noise, adequately decoupled supply rail for precision measurements. Place the supply bypass capacitor close to the relevant device power pins and preserve a low-impedance return path to the source. Supply rejection cannot be evaluated correctly without the actual supply bandwidth and regulator noise spectrum, so test the assembled circuit with the intended power architecture rather than relying only on the amplifier's nominal gain-bandwidth specification.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for the exact OPA2227U ordering code. Confirm these attributes using the manufacturer product page or the applicable quality and environmental documentation.

Données vérifiées le : 2026-11-19 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

opa2227u datasheet OPA2227U pinout OPA2227U datasheet pdf OPA2227U 8-SOIC OPA2227U 8 MHz Texas Instruments OPA2227U OPA2227U low noise op amp OPA2227U sensor amplifier OPA2227U equivalent OPA2227U replacement OPA2227U drop-in replacement OPA2227U price OPA2227U stock

Composants & termes associés

Texas Instruments OPA2227U OPA2227 OPA2227UA OPA227U OPAx227 operational amplifier precision operational amplifier low-noise operational amplifier dual amplifier gain-bandwidth product 8 MHz 8-SOIC SOIC family surface mount SMD precision signal conditioning bridge sensor current measurement ADC driver active filter input offset voltage input bias current noise density instrumentation amplifier
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ