OPA627AM - 55V/us Precision JFET Op Amp | Texas Instruments
Référence : OPA627AM ✗ Fin de vieOPA627AM Présentation
An operational amplifier is an active analog component that uses high-gain differential amplification to increase the voltage difference between its two inputs. In the broader hierarchy, an operational amplifier belongs to the amplifier IC family, which supports analog signal conditioning within electronic control, measurement, audio and communication systems. The OPA627AM uses a precision JFET-input architecture, combining low input-bias current with low-noise operation and wide input-voltage capability.
The main performance characteristics include a 55 V/us slew rate, 0.8 uV/°C maximum drift and operation from 9 V to 36 V, equivalent to ±4.5 V to ±18 V in dual-supply operation. The manufacturer specifies many operating characteristics from -25°C to 85°C for P and D packages and from -55°C to 125°C for the LMC package. Its 8-pin metal-can package supports traditional through-hole PCB layouts and robust thermal conduction compared with a small plastic package.
OPA627AM is suited to precision amplifier stages, low-level sensor interfaces, laboratory measurement systems, audio preamplifiers and high-fidelity signal paths. Its high slew rate allows large-amplitude signals to be reproduced quickly, while the low drift characteristic helps preserve offset stability as temperature changes. The JFET input stage is particularly useful in circuits requiring low input-bias current and high input impedance.
When designing around the OPA627AM, pay close attention to supply bypass capacitors, input-bias-current return paths and output-current limits. Decoupling capacitors should be placed close to the supply pins, and the circuit should avoid long PCB traces that increase leakage or susceptibility to interference. Input common-mode voltage and output swing must remain within the limits published for the selected package and supply configuration.
This page combines the OPA627AM technical description, application guidance, pin-level design information, lifecycle considerations and replacement analysis. The design notes and comparison guidance focus on practical implementation decisions for engineers who need to preserve signal-chain performance when qualifying an operational amplifier for a new PCB or maintaining an existing precision analog board.
Alternatives de remplacement direct pour OPA627AM — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec OPA627AM (même facteur de forme et même empreinte) — différant par Mounting Type, Package.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesOPA627AM Valeurs maximales et caractéristiques électriques
| Product Type | Precision high-speed JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Slew Rate | 55 V/us |
| Maximum Input Voltage Drift | 0.8 uV/°C |
| Supply Voltage Range | 9 V to 36 V |
| Dual-Supply Operating Range | ±4.5 V to ±18 V |
| General-Purpose Temperature Range for P and D Packages | -25°C to 85°C |
| LMC Package Temperature Range | -55°C to 125°C |
| Boîtier | 8-pin TO-CAN (LMC / TO-99) |
| Type de montage | Through-hole |
| Input Architecture | JFET input |
| Application Category | Instrumentation operational amplifier |
Guide de configuration des broches du OPA627AM 8-pin to-can (lmc / to-99)
Configuration des broches du OPA627AM (boîtier 8-pin to-can (lmc / to-99)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour OPA627AM.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
OPA627AM convient pour 6 applications: Precision Instrumentation Amplifier, Low-Level Sensor Interface, High-Fidelity Audio Preamp, Laboratory Measurement Front End, Active Audio Filter, Industrial Control Signal Conditioning.
Precision Instrumentation Amplifier
OPA627AM fits low-level instrumentation stages where signal integrity, low drift and accurate differential measurement matter. Its published 55 V/us slew rate allows the amplifier to follow fast input transitions without the severe distortion associated with a slower large-signal response. The 0.8 uV/°C maximum drift specification also supports stable measurements as ambient temperature changes. Place close-fitting bypass capacitors at the supply pins, route the differential input as a short pair, and confirm the actual input and output operating limits in the manufacturer data before setting the gain and feedback network.
Recommandé
Low-Level Sensor Interface
OPA627AM can serve as the first high-input-impedance stage in a sensor interface when the design benefits from JFET inputs and a 55 V/us slew rate. The amplifier helps preserve small sensor signals before later filtering or digitization, while its low maximum drift specification supports measurement stability over temperature changes. The circuit should include a defined input bias-current return path, protection appropriate to the sensor source and supply bypassing close to the package. Confirm the common-mode range at the selected supply voltage because sensor output levels can move close to either rail.
Recommandé
High-Fidelity Audio Preamp
OPA627AM is appropriate for a precision preamplifier or active-filter stage where the combination of high slew rate and low drift supports faithful signal reproduction. The 55 V/us slew-rate specification provides ample dynamic response for audio waveforms, while the JFET-input architecture suits high-impedance sources. The amplifier is placed in a conventional inverting or non-inverting precision topology, with feedback components selected for the intended gain and bandwidth. Check the output swing against the maximum audio amplitude and use short, shielded input routing to reduce hum pickup and radio-frequency interference.
Recommandé
Laboratory Measurement Front End
OPA627AM is well suited to laboratory instrumentation because it combines a fast 55 V/us large-signal response with a maximum drift of 0.8 uV/°C. The fast response reduces distortion when the amplifier must process transient or periodic signals with significant amplitude. In a practical measurement front end, use the amplifier with clean regulated supplies, low-leakage input construction and carefully selected feedback resistors. Place the device close to the active sensor or source, avoid long high-impedance traces, and use guarding or shielding if moisture or surface contamination could disturb the input node.
Recommandé
Active Audio Filter
OPA627AM can implement a precision active-filter section when the signal path requires both accurate frequency response and strong large-signal behavior. Its 55 V/us slew rate helps preserve low distortion through filter transitions, while the low drift specification contributes to stable gain over changing temperature. Component tolerances and the amplifier's actual noise, gain and stability parameters must be evaluated to determine whether the topology meets the filter requirement. Place input, feedback and grounding components to minimize parasitic coupling, and verify phase margin using the manufacturer's recommended stability techniques.
Recommandé
Industrial Control Signal Conditioning
OPA627AM can condition low-level control or sensor signals in an industrial system where fast response and temperature-stable behavior are valuable. Its 1-circuit design allows the amplifier to be placed where the signal is strongest, avoiding long analog traces and reducing noise pickup. The circuit operates from 9 V to 36 V, providing flexibility for industrial supply rails, but the dual-supply and single-supply input and output ranges must be checked for each application. Use local supply decoupling, robust grounding and input protection suitable for the factory environment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour OPA627AM — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Package | 8-pin TO-CAN (LMC / TO-99) |
| Brand | Texas Instruments |
| Amplifier Type | Precision JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Slew Rate | 55 V/us |
| Maximum Input Voltage Drift | 0.8 uV/°C |
| Supply Voltage Range | 9 V to 36 V |
| Dual-Supply Operating Range | ±4.5 V to ±18 V |
| LMC Package Temperature Range | -55°C to 125°C |
Notes de conception
Follow the numbered TO-CAN orientation in the manufacturer pin-configuration drawing when creating the footprint. A metal-can package requires careful attention to the locating feature, lead spacing and hole pattern because it does not match an SOIC-8 land pattern. Confirm mechanical dimensions against the current package drawing and place the device where its metal case can make direct thermal contact to copper where practical.
Place the supply bypass capacitors immediately between each supply pin and ground, with the shortest possible traces and a direct ground return. The OPA627AM operates from 9 V to 36 V, but the selected rail arrangement still needs enough headroom for the intended input and output voltages. Check decoupled supply behavior with an oscilloscope because high-speed amplification can expose inadequate bypassing even when a slow bench test appears satisfactory.
Do not substitute an amplifier solely because it is also called a precision JFET op amp. The OPA627AM is an obsolete 8-pin TO-CAN device, and a modern replacement may use a different package, pinout, compensation arrangement or output-swing range. Before changing a legacy design, compare every pin, confirm common-mode and output limits, and validate stability and distortion on the intended board.
Route differential inputs as a compact pair and keep feedback components close to the amplifier pins. High-impedance input nodes should be protected from contamination, flux residue and moisture because leakage can disturb the bias point. For audio and instrumentation circuits, use a quiet ground reference and consider guarding or shielding if the source impedance is high or the enclosure shares earth connections with switching equipment.
Informations de conformité
Compliance declarations were not stated in the manufacturer and distributor information. Obtain product-specific environmental documentation for the exact orderable part and shipment.