OPA627AM - 55V/us Precision JFET Op Amp | Texas Instruments
部品番号: OPA627AM ✗ 生産終了OPA627AM 概要
An operational amplifier is an active analog component that uses high-gain differential amplification to increase the voltage difference between its two inputs. In the broader hierarchy, an operational amplifier belongs to the amplifier IC family, which supports analog signal conditioning within electronic control, measurement, audio and communication systems. The OPA627AM uses a precision JFET-input architecture, combining low input-bias current with low-noise operation and wide input-voltage capability.
The main performance characteristics include a 55 V/us slew rate, 0.8 uV/°C maximum drift and operation from 9 V to 36 V, equivalent to ±4.5 V to ±18 V in dual-supply operation. The manufacturer specifies many operating characteristics from -25°C to 85°C for P and D packages and from -55°C to 125°C for the LMC package. Its 8-pin metal-can package supports traditional through-hole PCB layouts and robust thermal conduction compared with a small plastic package.
OPA627AM is suited to precision amplifier stages, low-level sensor interfaces, laboratory measurement systems, audio preamplifiers and high-fidelity signal paths. Its high slew rate allows large-amplitude signals to be reproduced quickly, while the low drift characteristic helps preserve offset stability as temperature changes. The JFET input stage is particularly useful in circuits requiring low input-bias current and high input impedance.
When designing around the OPA627AM, pay close attention to supply bypass capacitors, input-bias-current return paths and output-current limits. Decoupling capacitors should be placed close to the supply pins, and the circuit should avoid long PCB traces that increase leakage or susceptibility to interference. Input common-mode voltage and output swing must remain within the limits published for the selected package and supply configuration.
This page combines the OPA627AM technical description, application guidance, pin-level design information, lifecycle considerations and replacement analysis. The design notes and comparison guidance focus on practical implementation decisions for engineers who need to preserve signal-chain performance when qualifying an operational amplifier for a new PCB or maintaining an existing precision analog board.
ドロップイン代替品: OPA627AM — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: OPA627AM (同一形状・フットプリント) — 相違点: Mounting Type, Package.
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストOPA627AM 最大定格&電気的特性
| Product Type | Precision high-speed JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Slew Rate | 55 V/us |
| Maximum Input Voltage Drift | 0.8 uV/°C |
| Supply Voltage Range | 9 V to 36 V |
| Dual-Supply Operating Range | ±4.5 V to ±18 V |
| General-Purpose Temperature Range for P and D Packages | -25°C to 85°C |
| LMC Package Temperature Range | -55°C to 125°C |
| パッケージ | 8-pin TO-CAN (LMC / TO-99) |
| 実装タイプ | Through-hole |
| Input Architecture | JFET input |
| Application Category | Instrumentation operational amplifier |
OPA627AM 8-pin to-can (lmc / to-99) ピン配置ガイド
OPA627AM (8-pin to-can (lmc / to-99) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA627AM.
詳細は データシート をご参照ください。
主な用途
OPA627AM の用途: 6 件s: Precision Instrumentation Amplifier, Low-Level Sensor Interface, High-Fidelity Audio Preamp, Laboratory Measurement Front End, Active Audio Filter, Industrial Control Signal Conditioning.
Precision Instrumentation Amplifier
OPA627AM fits low-level instrumentation stages where signal integrity, low drift and accurate differential measurement matter. Its published 55 V/us slew rate allows the amplifier to follow fast input transitions without the severe distortion associated with a slower large-signal response. The 0.8 uV/°C maximum drift specification also supports stable measurements as ambient temperature changes. Place close-fitting bypass capacitors at the supply pins, route the differential input as a short pair, and confirm the actual input and output operating limits in the manufacturer data before setting the gain and feedback network.
おすすめ
Low-Level Sensor Interface
OPA627AM can serve as the first high-input-impedance stage in a sensor interface when the design benefits from JFET inputs and a 55 V/us slew rate. The amplifier helps preserve small sensor signals before later filtering or digitization, while its low maximum drift specification supports measurement stability over temperature changes. The circuit should include a defined input bias-current return path, protection appropriate to the sensor source and supply bypassing close to the package. Confirm the common-mode range at the selected supply voltage because sensor output levels can move close to either rail.
おすすめ
High-Fidelity Audio Preamp
OPA627AM is appropriate for a precision preamplifier or active-filter stage where the combination of high slew rate and low drift supports faithful signal reproduction. The 55 V/us slew-rate specification provides ample dynamic response for audio waveforms, while the JFET-input architecture suits high-impedance sources. The amplifier is placed in a conventional inverting or non-inverting precision topology, with feedback components selected for the intended gain and bandwidth. Check the output swing against the maximum audio amplitude and use short, shielded input routing to reduce hum pickup and radio-frequency interference.
おすすめ
Laboratory Measurement Front End
OPA627AM is well suited to laboratory instrumentation because it combines a fast 55 V/us large-signal response with a maximum drift of 0.8 uV/°C. The fast response reduces distortion when the amplifier must process transient or periodic signals with significant amplitude. In a practical measurement front end, use the amplifier with clean regulated supplies, low-leakage input construction and carefully selected feedback resistors. Place the device close to the active sensor or source, avoid long high-impedance traces, and use guarding or shielding if moisture or surface contamination could disturb the input node.
おすすめ
Active Audio Filter
OPA627AM can implement a precision active-filter section when the signal path requires both accurate frequency response and strong large-signal behavior. Its 55 V/us slew rate helps preserve low distortion through filter transitions, while the low drift specification contributes to stable gain over changing temperature. Component tolerances and the amplifier's actual noise, gain and stability parameters must be evaluated to determine whether the topology meets the filter requirement. Place input, feedback and grounding components to minimize parasitic coupling, and verify phase margin using the manufacturer's recommended stability techniques.
おすすめ
Industrial Control Signal Conditioning
OPA627AM can condition low-level control or sensor signals in an industrial system where fast response and temperature-stable behavior are valuable. Its 1-circuit design allows the amplifier to be placed where the signal is strongest, avoiding long analog traces and reducing noise pickup. The circuit operates from 9 V to 36 V, providing flexibility for industrial supply rails, but the dual-supply and single-supply input and output ranges must be checked for each application. Use local supply decoupling, robust grounding and input protection suitable for the factory environment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA627AM — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-pin TO-CAN (LMC / TO-99) |
| Brand | Texas Instruments |
| Amplifier Type | Precision JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Slew Rate | 55 V/us |
| Maximum Input Voltage Drift | 0.8 uV/°C |
| Supply Voltage Range | 9 V to 36 V |
| Dual-Supply Operating Range | ±4.5 V to ±18 V |
| LMC Package Temperature Range | -55°C to 125°C |
設計ノート
Follow the numbered TO-CAN orientation in the manufacturer pin-configuration drawing when creating the footprint. A metal-can package requires careful attention to the locating feature, lead spacing and hole pattern because it does not match an SOIC-8 land pattern. Confirm mechanical dimensions against the current package drawing and place the device where its metal case can make direct thermal contact to copper where practical.
Place the supply bypass capacitors immediately between each supply pin and ground, with the shortest possible traces and a direct ground return. The OPA627AM operates from 9 V to 36 V, but the selected rail arrangement still needs enough headroom for the intended input and output voltages. Check decoupled supply behavior with an oscilloscope because high-speed amplification can expose inadequate bypassing even when a slow bench test appears satisfactory.
Do not substitute an amplifier solely because it is also called a precision JFET op amp. The OPA627AM is an obsolete 8-pin TO-CAN device, and a modern replacement may use a different package, pinout, compensation arrangement or output-swing range. Before changing a legacy design, compare every pin, confirm common-mode and output limits, and validate stability and distortion on the intended board.
Route differential inputs as a compact pair and keep feedback components close to the amplifier pins. High-impedance input nodes should be protected from contamination, flux residue and moisture because leakage can disturb the bias point. For audio and instrumentation circuits, use a quiet ground reference and consider guarding or shielding if the source impedance is high or the enclosure shares earth connections with switching equipment.
コンプライアンス情報
Compliance declarations were not stated in the manufacturer and distributor information. Obtain product-specific environmental documentation for the exact orderable part and shipment.