PCA9511A - Hot-Swappable I2C/SMBus Buffer 400kHz | NXP
Référence : PCA9511AD,118 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.98 | $1,98 |
| 10 | $1.78 | $17,80 |
| 100 | $1.45 | $145,00 |
| 500 | $1.19 | $595,00 |
| 1 000 | $0.96 | $960,00 |
PCA9511AD,118 Présentation
An I2C bus buffer is a type of interface IC that sits between two segments of an I2C or SMBus serial bus, electrically isolating them while repeating logic levels bidirectionally. In the interface IC hierarchy (bus buffer -> I2C repeater/extender -> interface IC -> semiconductor), buffers solve capacitance and contention limits: I2C bus capacitance is limited to roughly 400 pF, and multi-card backplanes quickly exceed this. Buffers partition the bus so each segment sees only its own load, while hot-swap variants additionally prevent corrupt data during card insertion.
Key features of the PCA9511A include hot-swap control circuitry that keeps the backplane disconnected until a stop command or bus idle occurs without bus contention on the card side; a rise-time accelerator (accelerator) that actively pulls SDA and SCL edges, allowing stronger pull-up current without violating the standard; and support for the full I2C-bus Standard-mode and Fast-mode rate of 400 kHz. According to the NXP datasheet, the control circuitry prevents connection until the backplane is idle, which is the defining hot-swap behavior of this family.
The PCA9511A uses a bidirectional buffer architecture that does not require a direction pin: it senses the direction of data flow dynamically, so no software changes or configuration are needed. The rise-time accelerator sources current into the bus edges only during transitions, reducing RC rise-time constraints of long backplane traces.
Typical applications include live-insertion I/O cards in telecom and server backplanes, CompactPCI and ATCA-style shelving systems, SMBus-based rack management, and any system where cards are added or removed while the chassis remains powered.
Design considerations: because the buffer is powered from 2.3 V to 3.6 V, level shifting to 5 V buses requires a companion translator such as the PCA9306 or TCA9517; also respect maximum bus capacitance per segment.
This page synthesizes distributor data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, as of 2026-10-20.
Alternatives de remplacement direct pour PCA9511AD,118 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PCA9511AD,118 (même facteur de forme et même empreinte) — différant par Function, Package, Number of Channels, Hot-Swap Support, Rise-Time Accelerator.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PCA9511AT,118
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TCA9511A
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TCA4311A
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PCA9515A
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PCA9512AD
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1.4 / unité
Voir la fiche technique →PCA9511AD,118 Spécifications
| Fonction | Hot-swappable I2C-bus and SMBus bus buffer with rise-time accelerator |
| Number of Channels | 1 (SDA + SCL bidirectional pair) |
| Supply Voltage Range | 2.3 V to 3.6 V |
| Maximum Data Rate | 400 kHz (I2C Fast-mode) |
| Type d'interface | I2C-bus / SMBus |
| Hot-Swap Support | Yes (connection on bus idle / stop command without card-side contention) |
| Rise-Time Accelerator | Yes, on SDA and SCL |
| Direction Control | Automatic, no direction pin required |
| Boîtier | SOIC-8 (8-SO) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
| Ordering Suffix | ,118 (standard packing, Tape & Reel) |
Guide de configuration des broches du PCA9511AD,118 soic-8 (8-so)
Configuration des broches du PCA9511AD,118 (boîtier soic-8 (8-so)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour PCA9511AD,118.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
PCA9511AD,118 convient pour 6 applications: Live I/O Card Insertion in Telecom Backplanes, Server and Storage SMBus Management, Industrial Control Backplanes, Power Shelf and Battery Management Systems, CompactPCI and Modular Chassis Systems, Optical Module and Line Card Serviceability.
Live I/O Card Insertion in Telecom Backplanes
The PCA9511A was designed specifically for inserting I/O cards into a live backplane without corrupting the SDA and SCL buses. Its control circuitry withholds the backplane connection until a stop command or bus idle occurs without card-side bus contention, so partially powered card logic cannot glitch the shared bus during insertion. With 400 kHz Fast-mode support and the rise-time accelerator driving heavily loaded backplane traces, one buffer partitions each card slot's capacitance from the main bus, keeping total per-segment capacitance within I2C limits. Place one PCA9511A per slot, with each buffer's backplane side tied to the shelf bus and card side to the slot connector, using segment-local pull-up resistors sized for that segment's capacitance.
Recommandé
Server and Storage SMBus Management
In server chassis and storage shelves, SMBus carries monitoring data from power supplies, fans, and temperature sensors, and maintenance often occurs while the system is powered. The PCA9511A buffers the SMBus between the shelf management controller and replaceable FRU modules: its hot-swap logic ensures that swapping a PSU or fan tray does not latch up or corrupt the management bus. The 2.3 V to 3.6 V supply integrates directly with 3.3 V management rails, and the rise-time accelerator maintains SMBus edge rates across long shelf wiring with substantial capacitance. Because direction sensing is automatic, no firmware changes are needed when FRUs are added, keeping BMC software architecture simple.
Recommandé
Industrial Control Backplanes
Industrial automation shelves and modular control systems frequently allow controller or I/O modules to be replaced without full system power-down to minimize downtime. The PCA9511A isolates each module's I2C segment so insertion transients are confined to the slot being serviced. Its automatic bidirectional buffering at up to 400 kHz transparently supports configuration reads and register writes between the backplane master and module peripherals. In noisy factory environments, buffering also restores drive strength, since the accelerator sources active current into SDA/SCL edges that would otherwise be slowed by long, capacitive backplane wiring. Segment each slot with its own buffer and pull-ups to keep per-segment capacitance within specification.
Recommandé
Power Shelf and Battery Management Systems
Battery packs and rectifier modules in telecom power shelves communicate over SMBus/I2C and are routinely hot-inserted during live operation. The PCA9511A on each battery or rectifier slot prevents insertion glitches from corrupting the shared management bus while the shelf controller polls charge status, voltage, and temperature registers. The rise-time accelerator is particularly valuable here because battery pack wiring adds significant capacitance; active edge assistance preserves rise-time compliance at the 100 kHz SMBus rate with margin to the 400 kHz Fast-mode limit. The 2.3 V minimum supply suits battery-pack local power, and automatic direction sensing means charge/discharge data flows need no direction control.
Recommandé
CompactPCI and Modular Chassis Systems
CompactPCI, MicroTCA-class, and custom modular chassis use I2C for slot identification and FRU information (IPMI-style EEPROM reads). The PCA9511A partitions the chassis management bus so each slot's connector and wiring capacitance is isolated, enabling more slots on one bus segment than the raw I2C 400 pF capacitance limit would otherwise allow. Hot-swap logic supports live replacement of FRU modules; the buffer only connects a slot when the backplane is at a stop/idle state with no card-side contention. Designers should allocate one buffer per slot, keep backplane-side pull-ups strong enough for total shelf loading, and use the accelerator to relax card-side rise-time requirements on long stub wiring.
Recommandé
Optical Module and Line Card Serviceability
Line cards and optical transponder shelves use I2C for module identification, digital diagnostics monitoring (DOM), and microcontroller configuration. Hot replacement of optical modules or line cards during maintenance windows requires a buffer that will not corrupt the bus at insertion - the PCA9511A's contention-aware connection logic provides exactly this. Its 400 kHz capability comfortably covers DOM register reads, and the rise-time accelerator keeps SDA/SCL edges sharp across the long traces of high-count optical shelves. Because the device is a pure buffer with automatic direction, existing firmware for module EEPROM access and DOM polling works unchanged, and each module cage can be isolated with its own buffer for maximum slot count.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PCA9511AD,118 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PCA9511AT,118 | TCA9511A | PCA9515A |
|---|---|---|---|---|
| Package | SOIC-8 | TSSOP-8 | SOIC-8 | SOIC-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | Texas Instruments | NXP Semiconductors |
| Hot-Swap Support | Yes | Yes | Yes | No |
| Rise-Time Accelerator | Yes | Yes | Yes | No |
| Maximum Data Rate | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Automatic Direction Sensing | Yes | Yes | Yes | Yes |
| Target Use Case | Live card insertion into backplane | Live insertion, compact footprint | Live insertion, second-source | Static bus capacitance partitioning |
Principaux différenciateurs
- Hardware hot-swap control with contention awareness (vs PCA9515A)
- Integrated rise-time accelerator (vs PCA9512A)
- Second-source availability in the same footprint (vs TCA9511A)
Notes de conception
Provide independent pull-up resistors on each side of the buffer. The PCA9511A isolates bus segments electrically, so the backplane segment and card segment each need pull-ups sized for their own capacitance - a single shared pull-up across the buffer will not work. On long backplane traces, use lower pull-up values (for example 1 kOhm to 2 kOhm) to exploit the rise-time accelerator's edge assistance, and keep the card-side stub wiring short to limit capacitance added at slot insertion.
Do not apply a 5 V bus directly to the PCA9511A - its supply range is 2.3 V to 3.6 V and the I/O is not 5 V tolerant in buffer mode. If the backplane runs at 5 V, cascade a level translator (PCA9306 or TCA9517) with this buffer: translator handles voltage domains, buffer handles hot-swap and capacitance partitioning. Also verify the ENABLE pin is properly tied in single-buffer designs; leaving it floating can cause indeterminate connection behavior during power-up.
Decouple VCC with a 100 nF ceramic capacitor placed within a few millimeters of the supply pin, with a solid ground return. In chassis designs where many buffers power up simultaneously, ensure the 3.3 V rail inrush from all decoupling capacitors and accelerator activity does not sag below the 2.3 V minimum supply, which could release the hot-swap connection state incorrectly and cause bus glitches during a multi-card power-up event.
Estimated: the rise-time accelerator actively sources current into SDA/SCL edges, so on very short, lightly loaded segments the edges may become faster than necessary. This is generally benign for I2C at 100-400 kHz, but for extremely short traces you may relax pull-up values to standard 4.7 kOhm rather than over-strengthening them. Reserve aggressive pull-ups for long, capacitive backplane wiring where the accelerator is genuinely needed to meet rise-time targets.
Informations de conformité
PCA9511AD,118 standard RoHS-compliant ordering variant per NXP ordering code convention; obtain REACH/halogen-free declarations from the NXP product page material data.
