PCA9534D - 8-Bit I2C GPIO Expander | NXP Semiconductors
Référence : PCA9534D ✗ Fin de viePCA9534D Présentation
An I/O expander is an interface IC that increases the number of GPIO pins available to a host controller through a serial bus. The PCA9534D occupies one I2C address and connects external buttons, LEDs, relays, and other digital circuits to a microcontroller or application processor. Its hierarchy is GPIO expander → I/O expander → bus interface IC → semiconductor.
The device offers three hardware address inputs, A0, A1, and A2, allowing up to eight PCA9534D devices to share one I2C bus. Each port pin can operate as an input or output, while the open-drain interrupt output can notify the host when a programmed input state changes. This reduces polling requirements and helps conserve host processing time.
The PCA9534D does not include internal I/O pull-up resistors. Unlike the PCA9554, this reduces current consumption when the I/O pins are held LOW, but it requires suitable external pull-ups where the application needs a defined input state. The PCA9534 is also pin-to-pin and I2C-address compatible with the PCF8574, although software changes are required for the enhanced register behavior.
Typical uses include industrial control panels, battery-powered instruments, LED status boards, alarm interfaces, and small embedded systems. A microcontroller can configure the ports through the I2C interface, read input states, update outputs, and use the interrupt line for event-driven operation.
PCB design should reserve the address-selection pins for stable logic levels and place pull-ups close to the bus master and expander. Account for the absence of internal I/O pull-ups and verify that the host firmware uses the PCA9534 register map rather than the simpler PCF8574 protocol.
This page combines device capabilities, replacement considerations, comparison data, and practical design guidance. The manufacturer currently identifies PCA9534D as End of Life, so lifecycle planning should include sourcing continuity and evaluation of active replacements.
Alternatives de remplacement direct pour PCA9534D — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PCA9534D (même facteur de forme et même empreinte) — différant par Package, Device Type, Interrupt Output, Mounting Type, Interface.
PCA9534DW
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PCA9554D
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PCA9534D
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PCA9534DBT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PCF8574DW
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PCA9534D Spécifications
| Number of GPIO Ports | 8 ports |
| Device Type | 8-bit I2C-bus and SMBus GPIO expander |
| Interrupt Output | 1 open-drain interrupt output |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Supported I2C Bus Speed | 100 kHz and 400 kHz |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Address Configuration Inputs | 3 hardware inputs, A0 through A2 |
| Maximum Devices on One Bus | 8 devices |
| Internal I/O Pull-Up Resistors | None |
| Process Technology | CMOS |
| Logic Interface | I2C-bus and SMBus |
| Nombre de broches | 16 pins |
| Boîtier | SO16 |
| Type de montage | Surface-mount SO package |
Configuration des broches de PCA9534D
| Broche 1 | A0 — Address input 0 |
| Broche 2 | A1 — Address input 1 |
| Broche 3 | A2 — Address input 2 |
| Broche 4 | P0 — Configurable I/O port 0 |
| Broche 5 | P1 — Configurable I/O port 1 |
| Broche 6 | P2 — Configurable I/O port 2 |
| Broche 7 | P3 — Configurable I/O port 3 |
| Broche 8 | GND — Ground |
| Broche 9 | P4 — Configurable I/O port 4 |
| Broche 10 | P5 — Configurable I/O port 5 |
| Broche 11 | P6 — Configurable I/O port 6 |
| Broche 12 | P7 — Configurable I/O port 7 |
| Broche 13 | INT — Interrupt output |
| Broche 14 | SCL — Serial clock input |
| Broche 15 | SDA — Serial data input and output |
| Broche 16 | VCC — Power supply |
Applications typiques
PCA9534D convient pour 6 applications: Industrial Control Panel Interfaces, Battery-Powered Instrumentation, LED Status and Indicator Boards, Alarm and Security Interfaces, Small Embedded System GPIO Expansion, Communications Equipment Control.
Industrial Control Panel Interfaces
The PCA9534D is well suited to industrial control panels that need more than eight digital inputs or outputs. Its 8-bit port count can drive status LEDs, sense pushbuttons, or supervise relay-control signals while the host communicates through I2C or SMBus. Three address inputs permit up to eight devices on one bus, and the interrupt output can alert the controller when an input changes. Because the device has no internal I/O pull-ups, the design must provide appropriate external biasing where required. The 2.3 V to 5.5 V operating range supports common industrial control rails when electrical limits are verified for the finished equipment.
Recommandé
Battery-Powered Instrumentation
PCA9534D suits portable instruments where conserving standby current is important. Its low-power CMOS design and lack of internal I/O pull-up resistors reduce unnecessary current when lines are held LOW, while eight ports can expand sensor enables, mode controls, and status indicators. The device operates from 2.3 V to 5.5 V, allowing use with low-voltage system rails. The interrupt function can reduce repeated polling by waking the controller only after a configured input event. External pull-up values should be selected carefully because excessive current or slow bus rise times can undermine the low-power objective.
Recommandé
LED Status and Indicator Boards
An 8-bit I/O expander is a practical way to control many LEDs without consuming most of a microcontroller's GPIO pins. PCA9534D can drive discrete status indicators or support a multiplexed display interface through its configurable ports. The host writes output states over I2C, while the interrupt line can report external button or fault events. Operating from 2.3 V to 5.5 V supports both low-voltage and 5 V indicator arrangements. Since the PCA9534D has no internal I/O pull-ups, LED anodes, key inputs, and bus signal biasing must be designed explicitly on the PCB.
Recommandé
Alarm and Security Interfaces
PCA9534D can add isolated-looking digital alarm inputs and local output control to a security controller. Eight configurable ports can monitor door contacts, tamper switches, or zone-change signals, while the interrupt output provides an event-driven path back to the host. The 100 kHz and 400 kHz I2C rates support short internal control-bus connections, and three address inputs permit multiple expansion sections. The 2.3 V to 5.5 V supply range is useful for compact electronic security equipment. Actual deployments may require external isolation, surge protection, and regulatory controls beyond the PCA9534D itself.
Recommandé
Small Embedded System GPIO Expansion
PCA9534D is useful in small embedded systems where a microcontroller has too few pins for control logic, communications enables, and user inputs. The eight ports can be configured individually as inputs or outputs, and the dedicated interrupt output allows the processor to avoid continuous status polling. I2C connectivity keeps the expansion compact, while the SO16 package simplifies routing on a space-constrained PCB. Firmware must use the PCA9534 register map because it is not software-identical to the PCF8574. The device can also coexist with other peripherals through hardware-selectable addresses, subject to bus loading.
Recommandé
Communications Equipment Control
PCA9534D can handle discrete control functions in communications equipment where the main processor or communications controller needs additional status and configuration lines. The eight GPIO ports can supervise module enables, fault inputs, reset signals, or front-panel indicators, and the interrupt output supports event-driven monitoring. Its 2.3 V to 5.5 V operating range accommodates common equipment rails. Three address pins permit several PCA9534D devices to share an I2C management bus, while 400 kHz operation is suitable for board-level control traffic. The design must account for the absence of internal I/O pull-ups and ensure signal levels remain compatible with every connected circuit.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PCA9534D — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PCA9534 | PCA9554D | PCA9534D | PCA9534DBT | PCF8574D |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SO16 | SO16 | SO16 | SO16 | SO16 | SO16 |
| GPIO Port Count | 8 ports | 8 ports | 8 ports | 8 ports | 8 ports | 8 ports |
| Interrupt Output | Yes | Yes | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Lower-power behavior from omitted I/O pull-ups (vs PCA9554D)
- Direct hardware address selection (vs PCF8574D)
- Event-driven host notification (vs PCA9534DBT)
- Compact 16-pin serial expansion (vs PCA9534)
Notes de conception
Route A0, A1, and A2 to fixed logic states and place their components where accidental configuration changes cannot occur. The NXP manufacturer datasheet identifies three address inputs, permitting eight device addresses on one I2C bus. If an address must be selectable, include a documented programming interface or jumper arrangement, but prevent intermediate floating states during reset and power-up.
Do not assume that the PCA9534D contains internal I/O pull-ups. The manufacturer datasheet states that these resistors are absent, unlike the PCA9554. Add external pull-ups where a defined input state or valid bus level is required, and review the resulting current consumption. Changing from PCA9554D to PCA9534D can therefore alter both board behavior and firmware expectations.
Place the interrupt trace away from high-current switching nodes and use the open-drain interrupt arrangement with an appropriate pull-up. Because the PCA9534D is pin-to-pin compatible with the PCF8574, preserve the same physical footprint when moving between those devices, but adapt the software for the PCA9534 register map described in NXP application note AN469.
Decouple the PCA9534D close to its supply pin with a local capacitor selected according to the manufacturer recommendations and the host power-supply characteristics. Keep the supply within 2.3 V to 5.5 V and ensure the I2C pull-up voltage does not exceed the permitted input range. This is especially important in mixed-voltage systems where a 5 V pull-up could otherwise conflict with a lower-voltage controller.
Informations de conformité
The manufacturer product page identifies PCA9534D as End of Life but does not present specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose interface IC because it is not presented as an automotive-qualified variant.