הודעת רכישה אחרונה: PCA9534D מתקרב לסוף חיי המוצר. תאריך הזמנה אחרון: צור קשר. צפייה בחלקים חלופיים זמינים →
NXP Semiconductors

PCA9534D - 8-Bit I2C GPIO Expander | NXP Semiconductors

MPN: PCA9534D ✗ סוף ייצור
2.3 V to 5.5 V Vdss SO16 Package 400 kHz Speed
כמות הזמנה מינימלית: 1 |

PCA9534D סקירה

The NXP Semiconductors PCA9534D is an 8-bit CMOS I2C-bus and SMBus GPIO expander with an interrupt output, packaged in a 16-pin SO package. It provides eight configurable general-purpose input/output ports, operates from 2.3 V to 5.5 V, supports I2C and SMBus communication at 100 kHz and 400 kHz, and is specified for temperatures from -40 °C to +85 °C.

An I/O expander is an interface IC that increases the number of GPIO pins available to a host controller through a serial bus. The PCA9534D occupies one I2C address and connects external buttons, LEDs, relays, and other digital circuits to a microcontroller or application processor. Its hierarchy is GPIO expander → I/O expander → bus interface IC → semiconductor.

The device offers three hardware address inputs, A0, A1, and A2, allowing up to eight PCA9534D devices to share one I2C bus. Each port pin can operate as an input or output, while the open-drain interrupt output can notify the host when a programmed input state changes. This reduces polling requirements and helps conserve host processing time.

The PCA9534D does not include internal I/O pull-up resistors. Unlike the PCA9554, this reduces current consumption when the I/O pins are held LOW, but it requires suitable external pull-ups where the application needs a defined input state. The PCA9534 is also pin-to-pin and I2C-address compatible with the PCF8574, although software changes are required for the enhanced register behavior.

Typical uses include industrial control panels, battery-powered instruments, LED status boards, alarm interfaces, and small embedded systems. A microcontroller can configure the ports through the I2C interface, read input states, update outputs, and use the interrupt line for event-driven operation.

PCB design should reserve the address-selection pins for stable logic levels and place pull-ups close to the bus master and expander. Account for the absence of internal I/O pull-ups and verify that the host firmware uses the PCA9534 register map rather than the simpler PCF8574 protocol.

This page combines device capabilities, replacement considerations, comparison data, and practical design guidance. The manufacturer currently identifies PCA9534D as End of Life, so lifecycle planning should include sourcing continuity and evaluation of active replacements.

חלופות תחליף ישיר עבור PCA9534D — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם PCA9534D (אותו גורם צורה וטביעת רגל) — שונים ב Package, Device Type, Interrupt Output, Mounting Type, Interface.

Texas Instruments
Package: 16-SOIC
Device Type: 8-bit I2C/SMBus I/O expander
Interrupt Output: Yes
השווה עם PCA9534D →
NXP Semiconductors
Package: SO16, 16 pins
Device Type: 8-bit I2C-bus/SMBus I/O expander with interrupt
השווה עם PCA9534D →
Texas Instruments
Package: 16-SOIC
Interrupt Output: Open-drain
Mounting Type: Surface mount
השווה עם PCA9534D →

PCA9534DW

✅ Drop-In
Texas Instruments
📦 SO16
8-bit I2C/SMBus I/O expander · 8 · 2.3 V to 5.5 V · 400 kHz · I2C/SMBus · Push-pull · Yes · Yes

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

PCA9554D

✅ Drop-In
NXP Semiconductors
📦 SO16
8-bit I2C-bus/SMBus I/O expander with interrupt · 8 bits · I2C and SMBus · 400 kHz · SO16, 16 pins · CMOS · Serial I2C/SMBus interface for host communication · 8 configurable general-purpose I/O lines

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

PCA9534D

✅ Drop-In
NXP Semiconductors
📦 SO16
8 ports · 8-bit I2C-bus and SMBus GPIO expander · 1 open-drain interrupt output · 2.3 V to 5.5 V · 400 kHz · 100 kHz and 400 kHz · -40 °C to +85 °C · 3 hardware inputs, A0 through A2

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

PCA9534DBT

✅ Drop-In
📦 SO16
Same 8-bit GPIO and 16-pin footprint as PCA9534D; device-rating and packaging differences are 0% in port count and 0% in bus width.

📋 חלופה להתייחסות (לא בקטלוג)

PCF8574DW

✅ Drop-In
Texas Instruments
📦 SO16
8-bit I2C I/O expander · 8 · 100 kHz · 2.5 V to 6 V VCC · 2.5 V to 5.5 V · I2C two-line bidirectional bus · Quasi-bidirectional I/O · Open-drain

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

PCA9534D מפרטים

Number of GPIO Ports 8 ports
Device Type 8-bit I2C-bus and SMBus GPIO expander
Interrupt Output 1 open-drain interrupt output
Supply Voltage Range 2.3 V to 5.5 V
Maximum I2C Bus Frequency 400 kHz
Supported I2C Bus Speed 100 kHz and 400 kHz
טווח טמפרטורת פעולה -40 °C to +85 °C
Address Configuration Inputs 3 hardware inputs, A0 through A2
Maximum Devices on One Bus 8 devices
Internal I/O Pull-Up Resistors None
Process Technology CMOS
Logic Interface I2C-bus and SMBus
מספר פינים 16 pins
מארז SO16
סוג הרכבה Surface-mount SO package

תצורת פינים של PCA9534D

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
פין 1 A0 — Address input 0
פין 2 A1 — Address input 1
פין 3 A2 — Address input 2
פין 4 P0 — Configurable I/O port 0
פין 5 P1 — Configurable I/O port 1
פין 6 P2 — Configurable I/O port 2
פין 7 P3 — Configurable I/O port 3
פין 8 GND — Ground
פין 9 P4 — Configurable I/O port 4
פין 10 P5 — Configurable I/O port 5
פין 11 P6 — Configurable I/O port 6
פין 12 P7 — Configurable I/O port 7
פין 13 INT — Interrupt output
פין 14 SCL — Serial clock input
פין 15 SDA — Serial data input and output
פין 16 VCC — Power supply

יישומים טיפוסיים

PCA9534D מתאים עבור 6 יישוםs: Industrial Control Panel Interfaces, Battery-Powered Instrumentation, LED Status and Indicator Boards, Alarm and Security Interfaces, Small Embedded System GPIO Expansion, Communications Equipment Control.

🏭

Industrial Control Panel Interfaces

The PCA9534D is well suited to industrial control panels that need more than eight digital inputs or outputs. Its 8-bit port count can drive status LEDs, sense pushbuttons, or supervise relay-control signals while the host communicates through I2C or SMBus. Three address inputs permit up to eight devices on one bus, and the interrupt output can alert the controller when an input changes. Because the device has no internal I/O pull-ups, the design must provide appropriate external biasing where required. The 2.3 V to 5.5 V operating range supports common industrial control rails when electrical limits are verified for the finished equipment.

🔧

Battery-Powered Instrumentation

PCA9534D suits portable instruments where conserving standby current is important. Its low-power CMOS design and lack of internal I/O pull-up resistors reduce unnecessary current when lines are held LOW, while eight ports can expand sensor enables, mode controls, and status indicators. The device operates from 2.3 V to 5.5 V, allowing use with low-voltage system rails. The interrupt function can reduce repeated polling by waking the controller only after a configured input event. External pull-up values should be selected carefully because excessive current or slow bus rise times can undermine the low-power objective.

💡

LED Status and Indicator Boards

An 8-bit I/O expander is a practical way to control many LEDs without consuming most of a microcontroller's GPIO pins. PCA9534D can drive discrete status indicators or support a multiplexed display interface through its configurable ports. The host writes output states over I2C, while the interrupt line can report external button or fault events. Operating from 2.3 V to 5.5 V supports both low-voltage and 5 V indicator arrangements. Since the PCA9534D has no internal I/O pull-ups, LED anodes, key inputs, and bus signal biasing must be designed explicitly on the PCB.

🔒

Alarm and Security Interfaces

PCA9534D can add isolated-looking digital alarm inputs and local output control to a security controller. Eight configurable ports can monitor door contacts, tamper switches, or zone-change signals, while the interrupt output provides an event-driven path back to the host. The 100 kHz and 400 kHz I2C rates support short internal control-bus connections, and three address inputs permit multiple expansion sections. The 2.3 V to 5.5 V supply range is useful for compact electronic security equipment. Actual deployments may require external isolation, surge protection, and regulatory controls beyond the PCA9534D itself.

🧩

Small Embedded System GPIO Expansion

PCA9534D is useful in small embedded systems where a microcontroller has too few pins for control logic, communications enables, and user inputs. The eight ports can be configured individually as inputs or outputs, and the dedicated interrupt output allows the processor to avoid continuous status polling. I2C connectivity keeps the expansion compact, while the SO16 package simplifies routing on a space-constrained PCB. Firmware must use the PCA9534 register map because it is not software-identical to the PCF8574. The device can also coexist with other peripherals through hardware-selectable addresses, subject to bus loading.

🌐

Communications Equipment Control

PCA9534D can handle discrete control functions in communications equipment where the main processor or communications controller needs additional status and configuration lines. The eight GPIO ports can supervise module enables, fault inputs, reset signals, or front-panel indicators, and the interrupt output supports event-driven monitoring. Its 2.3 V to 5.5 V operating range accommodates common equipment rails. Three address pins permit several PCA9534D devices to share an I2C management bus, while 400 kHz operation is suitable for board-level control traffic. The design must account for the absence of internal I/O pull-ups and ensure signal levels remain compatible with every connected circuit.

What is the PCA9534D and what does it do?
The PCA9534D is an 8-bit CMOS GPIO expander that adds eight configurable I/O ports to an I2C-bus or SMBus host. According to the NXP manufacturer datasheet, it includes a programmable I/O port, an interrupt output, and a low-power design intended to reduce consumption when I/O pins are held LOW. It is used when a microcontroller or processor needs more digital inputs and outputs than its own package provides.
What is the operating voltage of PCA9534D?
The PCA9534D operates from 2.3 V to 5.5 V. This range allows the same expander to interface with common 2.5 V, 3.3 V, and 5 V systems when the associated bus levels and pull-up arrangement are compatible. The NXP manufacturer datasheet identifies the device as a low-power CMOS GPIO expander, while device-specific input and output voltage limits should be checked against the selected system rail.
What are the key specifications of PCA9534D that engineers should know?
The principal PCA9534D specifications are 8 GPIO ports, a 2.3 V to 5.5 V supply range, 100 kHz and 400 kHz I2C operating speeds, three hardware address inputs, and one interrupt output. The NXP manufacturer datasheet also states that the I/O ports lack internal pull-up resistors, an important distinction from the closely related PCA9554. The device is offered in a 16-pin SO package.
Where can I download the PCA9534D datasheet PDF?
The official PCA9534D datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9534.pdf. The document defines the pin configuration, electrical characteristics, register map, address selection, and application information. Engineers replacing a PCF8574 should also consult NXP application note AN469 because the PCA9534 adds register functions that require software changes.
Where can I find the PCA9534D pinout?
The PCA9534D pinout is documented in the manufacturer datasheet and follows a standard 16-pin SOIC arrangement. Pins 1 through 3 are A0, A1, and A2; pins 4 through 7 are P0 through P3; pin 8 is GND; pins 9 through 12 are P4 through P7; pin 13 is INT; pins 14 and 15 are SCL and SDA; and pin 16 is VCC. Use the datasheet pin-description table when assigning PCB tracks.
Does PCA9534D have internal pull-up resistors?
No, the PCA9534D does not include internal I/O pull-up resistors. The NXP manufacturer datasheet specifically contrasts it with the PCA9554, which has internal pull-ups; removing them reduces power consumption when the I/O pins are held LOW. Add external pull-ups only where the connected circuit requires a defined logic level, and select their values according to the bus voltage and signal-rate requirements.
Can PCF8574D replace PCA9534D?
The PCF8574D is pin-to-pin and I2C-address compatible with the PCA9534, but it is not a firmware-compatible replacement. According to the NXP manufacturer datasheet and application note AN469, the PCA9534 adds enhanced register functions that require software changes. Existing boards may retain their physical routing, but the host driver must be rewritten or adapted before substituting the devices.
What can replace PCA9534D?
The PCA9534D can be replaced by a device with the same 16-pin SO footprint, compatible I2C address arrangement, and equivalent GPIO and interrupt behavior. Potentially relevant options include the NXP PCA9534 family, TI PCA9534 variants in compatible SO packages, and the NXP PCA9554D, although the latter adds internal I/O pull-ups. NXP identifies PCA9534D as End of Life, so confirm lifecycle status and firmware requirements before approving a substitute.
PCA9534D vs PCA9554D: which is better for a low-power design?
The PCA9534D is generally preferable for a low-power design whose I/O pins are actively held LOW because it omits internal I/O pull-up resistors. The PCA9554D is electrically useful when internal pull-ups are desired, but those resistors can increase current consumption depending on the pin state. The choice also depends on register compatibility and whether the existing firmware already targets one of the two devices.
When should I choose PCA9534D over PCA9554D?
Choose the PCA9534D when the board intentionally holds I/O lines LOW and needs the lower power behavior associated with having no internal I/O pull-ups. Choose the PCA9554D when internal pull-ups simplify the input biasing or when its register behavior already matches the firmware. Both devices provide eight-bit I2C I/O expansion, so bus and package compatibility should also be checked.
How many PCA9534D devices can share one I2C bus?
Up to eight PCA9534D devices can share one I2C bus by using the A0, A1, and A2 address inputs to assign different addresses. The NXP manufacturer datasheet identifies three hardware address pins, producing eight address combinations. The host processor must select the correct address for each peripheral, and the complete bus pull-up network must support the intended bus capacitance and communication speed.
Is PCA9534D suitable for industrial control and instrumentation?
The PCA9534D is suitable for many industrial control and instrumentation designs that require a low-power 8-bit GPIO expansion at 2.3 V to 5.5 V. Its specified operating range of -40 °C to +85 °C covers many commercial and industrial environments, while the interrupt output supports event-driven handling of switches and alarm signals. Final suitability should include environmental qualification, isolation, and protection requirements specific to the installation.
How should PCA9534D pull-ups and address pins be designed?
Connect A0, A1, and A2 to stable logic levels before the device begins operating so that each PCA9534D receives a unique I2C address. Do not rely on internal I/O pull-ups for the external bus because the device does not include them. Place any required bus pull-ups close to the relevant bus endpoints and follow the manufacturer recommendations for capacitance, rise time, and signal integrity.
What is the lead time for PCA9534D?
Lead time for PCA9534D depends on remaining supply and the quantity required. NXP identifies the device as End of Life, so new production is not assured. Request the current quantity, lead time, and sourcing status through the Request a Quote form on this page. Engineers should also assess an active replacement early because firmware and external pull-up differences can affect redesign work.
Where to buy PCA9534D online and is it in stock?
Use the Request a Quote form on this page to request PCA9534D availability, current pricing, and lead time. NXP identifies the PCA9534D as End of Life, meaning inventory may be limited and future supply cannot be assumed. For production planning, request exact lot and traceability information and evaluate the listed alternatives for package, pin, register, and lifecycle compatibility.

נתוני עזר הנדסיים עבור PCA9534D — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the PCA9534D for an existing NXP-based design that uses an 8-bit I2C GPIO expander, has a 2.3 V to 5.5 V supply, and benefits from the absence of internal I/O pull-ups. It is particularly appropriate when lower current consumption with lines held LOW is important and the firmware already supports the PCA9534 register map. Select PCA9554D when internal pull-ups simplify the circuit or match existing firmware, but recheck current use across all port states. The Texas Instruments PCA9534D and PCA9534DBT are functional alternatives in the same SO16 footprint, subject to manufacturer-specific electrical ratings and lifecycle review. PCF8574D preserves the physical and I2C-address arrangement, yet application note AN469 confirms that software changes are required. Because NXP labels PCA9534D End of Life, validate long-term availability and approve an active lifecycle strategy before committing to new production.

השוואה עם חלופות

פרמטר מוצר זה PCA9534 PCA9554D PCA9534D PCA9534DBT PCF8574D
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors Texas Instruments Texas Instruments Texas Instruments
Package SO16 SO16 SO16 SO16 SO16 SO16
GPIO Port Count 8 ports 8 ports 8 ports 8 ports 8 ports 8 ports
Interrupt Output Yes Yes Yes Yes Yes Yes

מבדילים עיקריים

  • Lower-power behavior from omitted I/O pull-ups (לעומתPCA9554D)
  • Direct hardware address selection (לעומתPCF8574D)
  • Event-driven host notification (לעומתPCA9534DBT)
  • Compact 16-pin serial expansion (לעומתPCA9534)

הערות תכנון

Route A0, A1, and A2 to fixed logic states and place their components where accidental configuration changes cannot occur. The NXP manufacturer datasheet identifies three address inputs, permitting eight device addresses on one I2C bus. If an address must be selectable, include a documented programming interface or jumper arrangement, but prevent intermediate floating states during reset and power-up.

Do not assume that the PCA9534D contains internal I/O pull-ups. The manufacturer datasheet states that these resistors are absent, unlike the PCA9554. Add external pull-ups where a defined input state or valid bus level is required, and review the resulting current consumption. Changing from PCA9554D to PCA9534D can therefore alter both board behavior and firmware expectations.

Place the interrupt trace away from high-current switching nodes and use the open-drain interrupt arrangement with an appropriate pull-up. Because the PCA9534D is pin-to-pin compatible with the PCF8574, preserve the same physical footprint when moving between those devices, but adapt the software for the PCA9534 register map described in NXP application note AN469.

Decouple the PCA9534D close to its supply pin with a local capacitor selected according to the manufacturer recommendations and the host power-supply characteristics. Keep the supply within 2.3 V to 5.5 V and ensure the I2C pull-up voltage does not exceed the permitted input range. This is especially important in mixed-voltage systems where a 5 V pull-up could otherwise conflict with a lower-voltage controller.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The manufacturer product page identifies PCA9534D as End of Life but does not present specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose interface IC because it is not presented as an automotive-qualified variant.

חיפושים קשורים

PCA9534D datasheet PCA9534D pinout PCA9534D datasheet pdf PCA9534D equivalent PCA9534D replacement PCA9534D cross reference PCA9534D vs PCA9554D PCA9534D vs PCF8574D PCA9534D SO16 GPIO expander PCA9534D 8-bit I2C expander NXP PCA9534D PCA9534D price PCA9534D stock PCA9534D application circuit

רכיבים ומונחים קשורים

NXP Semiconductors PCA9534D PCA9534 PCA9554D PCF8574D Texas Instruments PCA9534DBT I/O expander GPIO expander interface IC I2C-bus SMBus CMOS SO16 SOIC family surface-mount package SMD interrupt output A0 A1 A2 2.3 V 5.5 V 400 kHz low-power I/O port
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר