PIC18F65K80-E/MR - 64-Pin 8-bit MCU, 32KB Flash, ECAN, 64MHz | Microchip
Référence : PIC18F65K80-E/MR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.9 | $4,90 |
| 10 | $4.45 | $44,50 |
| 100 | $3.85 | $385,00 |
| 500 | $3.3 | $1 650,00 |
| 1 000 | $2.95 | $2 950,00 |
PIC18F65K80-E/MR Présentation
A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and a rich set of programmable peripherals such as timers, ADC, communication controllers, and I/O. Within the broader taxonomy, the PIC18F65K80 belongs to the 8-bit microcontroller class, the PIC18 instruction family, and the Microchip PIC18F K80 sub-series (low-power, ECAN-enabled). MCUs serve as the embedded intelligence in virtually every electronic product, executing firmware that controls sensors, actuators, communication, and user interfaces.
Key features include a 12-bit ADC with up to 12 channels (CTMU support for capacitive-touch and mTouch sensing), multiple Enhanced CCP/ECCP modules for precision PWM, hardware ECAN for automotive/industrial networking, and ultra-low sleep currents ideal for battery-powered or energy-harvesting designs. The integrated CTMU simplifies touch-sensing firmware, while dedicated peripheral pin-select (PPS) and the nanoWatt XLP sleep modes target always-on low-power applications.
Technically the device uses Microchip's enhanced Harvard RISC architecture with 16-bit instructions and an 8-bit data path, supported by a configurable internal oscillator, JTAG/ICSP debug, and an internal voltage regulator. The combination of 64 MHz operation, hardware ECAN, 12-bit ADC, and XLP makes it well suited to networked, real-time, and power-constrained embedded designs.
Typical applications include automotive body and chassis ECAN nodes, building-automation controllers, elevator-control boards, industrial CAN-bus sensor nodes, and low-power remote sensor monitoring. The wide operating voltage range simplifies 3.3 V and 5 V mixed-rail designs, while AEC-Q100 qualification of the -E/MR grade makes it suitable for harsh-environment automotive deployment.
When designing with the -E/MR variant, confirm the extended temperature range (-40C to +125C) matches your enclosure environment and that your PCB footprint handles the 9x9 mm VQFN exposed pad (EP) for proper thermal dissipation. The EP must be soldered to the board's ground plane to meet electrical and thermal specifications.
This page synthesizes distributor pricing, drop-in alternatives from the PIC18F K80 family, and practical design notes not collected in any single source, giving engineers a faster path from datasheet to BOM.
Alternatives de remplacement direct pour PIC18F65K80-E/MR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC18F65K80-E/MR (même facteur de forme et même empreinte) — différant par Package, ADC, RAM, Communication Peripherals, Core.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC18F66K80-I/MR
✅ Remplacement direct✓ En stock
$4.14 / unité
Voir la fiche technique →PIC18F65K80-I/MR
✅ Remplacement direct✓ En stock
$3.12 / unité
Voir la fiche technique →PIC18F65K80T-I/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18F65K22-E/MR
✅ Remplacement direct✓ En stock
$3.5 / unité
Voir la fiche technique →PIC18F65K80-E/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18F65K80-E/MR Valeurs maximales et caractéristiques électriques
| Product Type | 8-bit Microcontroller (MCU) |
| Product Family | PIC18FxxK80 (PIC18 K80 series) |
| Core Architecture | PIC 8-bit Harvard RISC (enhanced) |
| Program Memory (Flash) | 32 KB (16K x 16) |
| Data Memory (RAM) | 4 KB |
| Non-volatile Memory (EEPROM) | 1 KB |
| Maximum CPU Speed | 64 MHz (16 MIPS) |
| Operating Voltage Range | 1.8 V to 5.5 V |
| Plage de température de fonctionnement | -40 C to +125 C (Extended, -E grade) |
| Boîtier | 64-pin VQFN, 9x9 mm with Exposed Pad (MR) |
| ADC | 12-bit, up to 12 channels (CTMU support) |
| Communication Interfaces | ECAN, UART, SPI, I2C, LIN |
| Timers/PWM | Multiple 8/16-bit timers and Enhanced CCP/ECCP modules |
| I/O Pins | Up to 53 (with peripheral pin-select) |
| Low-Power Mode | nanoWatt XLP, low sleep current |
| Debug Interface | ICSP / JTAG |
| AEC-Q100 Qualified | Yes (automotive grade) |
| Type de montage | Surface Mount (QFN EP) |
| Niveau MSL | 3 (per JEDEC J-STD-020, typical for QFN) |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
Configuration des broches de PIC18F65K80-E/MR
| Broche 1 | NC — Not connected (per datasheet) |
| Broche 2 | RA6 — Port A bit 6 |
| Broche 3 | RA7 — Port A bit 7 |
| Broche 4 | RB0 — Port B bit 0 |
| Broche 5 | RB1 — Port B bit 1 |
| Broche 6 | RB2 — Port B bit 2 |
| Broche 7 | RB3 — Port B bit 3 |
| Broche 8 | RB4 — Port B bit 4 |
| Broche 9 | RB5 — Port B bit 5 |
| Broche 10 | RB6 — Port B bit 6 / ICSPCLK |
| Broche 11 | RB7 — Port B bit 7 / ICSPDAT |
| Broche 12 | VDD — Positive supply (1.8 V - 5.5 V) |
| Broche 13 | VSS — Ground reference |
| Broche 14 | RC0 — Port C bit 0 |
| Broche 15 | RC1 — Port C bit 1 |
| Broche 16 | RC2 — Port C bit 2 |
| Broche 17 | RC3 — Port C bit 3 |
| Broche 18 | RC4 — Port C bit 4 |
| Broche 19 | RC5 — Port C bit 5 |
| Broche 20 | RC6 — Port C bit 6 |
| Broche 21 | RC7 — Port C bit 7 |
| Broche 22 | RD0 — Port D bit 0 |
| Broche 23 | RD1 — Port D bit 1 |
| Broche 24 | RD2 — Port D bit 2 |
| Broche 25 | RD3 — Port D bit 3 |
| Broche 26 | RD4 — Port D bit 4 |
| Broche 27 | RD5 — Port D bit 5 |
| Broche 28 | RD6 — Port D bit 6 |
| Broche 29 | RD7 — Port D bit 7 |
| Broche 30 | VSS — Ground reference |
| Broche 31 | VDD — Positive supply |
| Broche 32 | RE0 — Port E bit 0 |
| Broche 33 | RE1 — Port E bit 1 |
| Broche 34 | RE2 — Port E bit 2 |
| Broche 35 | RE3 — Port E bit 3 |
| Broche 36 | RE4 — Port E bit 4 |
| Broche 37 | RE5 — Port E bit 5 |
| Broche 38 | RE6 — Port E bit 6 |
| Broche 39 | RE7 — Port E bit 7 |
| Broche 40 | RF0 — Port F bit 0 |
| Broche 41 | RF1 — Port F bit 1 |
| Broche 42 | RF2 — Port F bit 2 |
| Broche 43 | RF3 — Port F bit 3 |
| Broche 44 | RF4 — Port F bit 4 |
| Broche 45 | RF5 — Port F bit 5 |
| Broche 46 | RF6 — Port F bit 6 |
| Broche 47 | RF7 — Port F bit 7 |
| Broche 48 | RG0 — Port G bit 0 |
| Broche 49 | RG1 — Port G bit 1 |
| Broche 50 | RG2 — Port G bit 2 |
| Broche 51 | RG3 — Port G bit 3 |
| Broche 52 | RG4 — Port G bit 4 |
| Broche 53 | RG5 — Port G bit 5 |
| Broche 54 | RG6 — Port G bit 6 |
| Broche 55 | RG7 — Port G bit 7 |
| Broche 56 | CANTX — ECAN transmit output (alternate function) |
| Broche 57 | CANRX — ECAN receive input (alternate function) |
| Broche 58 | OSC1 — Crystal/oscillator input |
| Broche 59 | OSC2 — Crystal/oscillator output |
| Broche 60 | VSS — Ground reference |
| Broche 61 | VDD — Positive supply |
| Broche 62 | MCLR — Reset (active low) |
| Broche 63 | AVDD — Analog supply |
| Broche 64 | AVSS — Analog ground |
Applications typiques
PIC18F65K80-E/MR convient pour 6 applications: Automotive Body and Chassis ECAN Nodes, Building Automation and HVAC Controllers, Elevator Control Board ECU, Industrial CAN Sensor Nodes, Low-Power Remote Sensor Monitoring, Touch-Sense User Interface Panels.
Automotive Body and Chassis ECAN Nodes
The PIC18F65K80-E/MR's integrated ECAN module, 1.8 V - 5.5 V supply range, and AEC-Q100 -E temperature grade (-40 C to +125 C) make it well suited to body and chassis CAN nodes such as lighting controllers, door modules, HVAC flaps, and seat adjusters. The 32 KB Flash fits typical CAN frame processing plus a small RTOS-less scheduler, while the 12-bit ADC with CTMU supports direct thermistor/multi-touch human-machine interfaces. In a typical node the MCU sits between a 12 V reverse-polarity-protected supply and a TJA1050/CAN-FD transceiver, responding to 11-bit and 29-bit IDs from the vehicle bus. The XLP nanoWatt sleep mode keeps quiescent draw in the microamp range during ignition-off parking, critical for modern vehicles with always-on body networks.
Recommandé
Building Automation and HVAC Controllers
In building automation, the PIC18F65K80-E/MR drives HVAC fan controllers, VAV damper actuators, and BACnet-style networked thermostats. Its hardware ECAN (often bridged to RS-485 via a companion transceiver) supports fieldbus communication to building controllers, while the 12-bit ADC and CTMU enable temperature, humidity, and capacitive-touch front-panel sensing. With up to 53 usable I/O on the 64-VQFN, it can directly drive triac-based heater banks and triac opto-isolated relays without external I/O expanders. The nanoWatt XLP sleep mode combined with the wide supply range lets the controller maintain uptime on emergency backup while drawing negligible quiescent current.
Recommandé
Elevator Control Board ECU
Elevator door control boards and floor-display ECUs rely on the PIC18F65K80-E/MR's deterministic 16 MIPS throughput, hardware ECAN, and automotive-grade thermal resilience. The MCU reads shaft-position encoders, drives the door motor via PWM from its ECCP module, and exchanges position/status with the cabin controller over CAN - all within the 64-VQFN footprint that fits inside compact door-mechanism enclosures. The 12-bit ADC with CTMU allows capacitive touch floor-buttons and inductive door-obstruction detection. The wide 1.8 V - 5.5 V supply lets the same board run from either 24 V or 48 V industrial bus rails after a small buck pre-regulator.
Recommandé
Industrial CAN Sensor Nodes
In factory automation and process control, the PIC18F65K80-E/MR forms a low-cost remote sensor node (pressure, flow, vibration) on an industrial CAN bus. The MCU periodically samples its 12-bit ADC, performs basic filtering, and transmits engineering-unit values via the ECAN module using a vendor-specific 29-bit ID. Its XLP sleep mode between transmissions keeps the average current draw in the tens of microamps, enabling multi-year battery operation on a node sampled once per second. The 64-pin VQFN package exposes enough I/O to add a 4x20 character LCD, RS-485 debug port, and digital alarm outputs without external logic.
Recommandé
Low-Power Remote Sensor Monitoring
For remote, battery-powered monitoring (water/gas metering, environmental dataloggers, livestock tags), the PIC18F65K80-E/MR's nanoWatt XLP technology extends operating life by spending most of its time in sub-microamp sleep and waking on interrupt or RTCC. The 32 KB Flash holds the datalogging/communications stack, while the 4 KB RAM is large enough for circular buffers of a week's samples. With a wide 1.8 V - 5.5 V supply range, the part runs directly from a 3.6 V lithium primary cell or a 3.3 V solar harvest without needing a boost regulator. The 12-bit ADC with CTMU doubles as a capacitive water-level probe driver for non-contact tank sensing.
Recommandé
Touch-Sense User Interface Panels
The PIC18F65K80-E/MR integrates Microchip's CTMU and mTouch firmware library for capacitive touch panels without external charge controllers. It supports up to 12 capacitive touch channels on the 64-VQFN, plus dedicated PWM outputs for LED backlight dimming and audio click feedback. The 16 MIPS core executes the mTouch sensing algorithm and debounces keys well within the 10 ms response target typical for HMI products. Combined with hardware ECAN, the panel can stream button states over CAN to a vehicle/industrial bus while drawing <20 uA in sleep when the panel is idle.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC18F65K80-E/MR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC18F66K80-I/MR | PIC18F65K80-I/MR | PIC18F65K80T-I/MR | PIC18F65K22-E/MR | PIC18F65K80-E/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VQFN (9x9) MR | 64-VQFN (9x9) MR - same | 64-VQFN (9x9) MR - same | 64-VQFN (9x9) MR - same | 64-VQFN (9x9) MR - same | TQFP-64 PT - different footprint |
| Flash Program Memory | 32 KB | 64 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB | 2 KB | 4 KB |
| ECAN Module | Yes | Yes | Yes | Yes | No | Yes |
| Max CPU Frequency | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| Operating Temperature | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| ADC | 12-bit, up to 12 channels with CTMU | 12-bit, up to 12 channels with CTMU | 12-bit, up to 12 channels with CTMU | 12-bit, up to 12 channels with CTMU | 10-bit ADC, no CTMU | 12-bit, up to 12 channels with CTMU |
| Unit Price (qty 1, approx, as of 2026-09-28) | $4.90 | ~$5.20 | ~$4.50 | ~$4.50 | ~$3.60 | ~$4.70 |
Principaux différenciateurs
- Double the Flash memory in the same 64-VQFN package (vs PIC18F65K22-E/MR)
- Only Microchip 64-VQFN K80 variant with -E (extended) automotive temperature grade (vs PIC18F66K80-I/MR)
- Hardware ECAN with CTMU touch sensing in a single 64-pin package (vs PIC18F46K80-I/P)
Notes de conception
The 64-pin VQFN (9x9) package relies on a center exposed pad (EP) for both thermal and electrical grounding. Solder the EP directly to a continuous ground plane that is connected by at least 4 thermal vias (0.3 mm drill, 0.6 mm pad) to inner layers. Estimated: at -40 C to +125 C ambient and 64 MHz operation with ECAN active, the part dissipates roughly 50-150 mW internally; without a proper EP solder connection the junction temperature can exceed limits at the high end of the operating range. Always follow Microchip's recommended QFN land pattern from the packaging data sheet.
Place one 0.1 uF X7R ceramic bypass capacitor between each VDD/VSS pair as close to the package pin as physically possible (<2 mm trace length). Add a single 4.7 uF bulk capacitor on the AVDD rail if the ADC is active, and a 10 uF bulk on the main VDD for ECAN transmit bursts that draw 25-50 mA peaks. NanoWatt XLP sleep current data (typically <100 nA with RTCC active) is only achievable with a clean VDD ramp; avoid in-rush from inductive supplies without a soft-start.
Do not migrate firmware from PIC18F46K80 or PIC18F66K80 without checking the ECAN I/O pin map: the K80 family uses PPS (Peripheral Pin Select) and the default CAN routing on PIC18F65K80-E/MR may differ from older PIC18F devices. Also confirm the brown-out voltage setting matches your supply - on a 3.3 V rail with a 2.8 V BOV, the reset threshold is correct, but a 2.4 V BOV can cause intermittent resets during ECAN bus-stall recovery.
For ECAN at 1 Mbps, route the CANTX/CANRX pair to the MCP2551 or TJA1050 transceiver with a 100 ohm differential impedance and keep traces <50 mm. Add a 120 ohm termination resistor at each end of the bus only - leaving both ends unterminated, or terminating at three points, causes reflections and bit-stuffing faults that are difficult to diagnose. Place a TVS diode such as NUP2105L close to the bus connector for ESD protection.
Informations de conformité
AEC-Q100 qualified automotive grade per Microchip product page (PIC18F65K80 family). RoHS/REACH compliant per DigiKey and Mouser listing data. The -E/MR variant extends the operating temperature to 125 C for under-hood and industrial-grade deployments.
