PIC32MX330F064L-I/PT - 80MHz, 64KB Flash MCU | Microchip 100-TQFP
Référence : PIC32MX330F064L-I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $6.93 | $6,93 |
| 10 | $6.24 | $62,40 |
| 100 | $5.55 | $555,00 |
| 500 | $5.1 | $2 550,00 |
| 1 000 | $4.62 | $4 620,00 |
PIC32MX330F064L-I/PT Présentation
A 32-bit microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. PIC32MX devices occupy the mid-range of the PIC32 family, sitting between low-cost PIC32MX1/2/3/4/5/6/7 entry-level devices and higher-end PIC32MZ parts. They are widely used as upgrade paths from 16-bit PIC24/dsPIC designs because they share peripheral libraries and pin-compatibility with many 16-bit DIP/PT packages, allowing migration without PCB rework.
Key features of the PIC32MX330F064L include 10-bit ADC with up to 1 Msps conversion rate, multiple UART/SPI/I2C interfaces, and MIPS16e code compression for up to 40% smaller code size. The device operates from 2.3 V to 3.6 V across the industrial -40C to +105C temperature range, supports low-power Idle and Sleep modes, and offers a 5-channel DMA controller for offloading CPU data movement. The 100-TQFP package provides generous I/O count for applications needing parallel buses, multiple serial interfaces, and USB connectivity simultaneously.
Typical applications include industrial control panels, USB audio devices, motor control front-ends, barcode scanners, point-of-sale terminals, and graphical display controllers. The CTMU enables touch sensing and capacitive measurement, while the PMP simplifies interfacing to graphical LCDs and external parallel peripherals such as FIFO memories and ASICs. Engineers migrating from PIC24FJ/PIC24H designs often select this part for its familiar development ecosystem (MPLAB X IDE, XC32 compiler, Harmony framework).
When designing with this part, place decoupling capacitors (100 nF + 10 uF bulk) as close as possible to every VDD/VSS pair, route the 48 MHz crystal traces symmetrically with ground guard rings, and verify USB-OTG board impedance (90 ohm differential) against the USB 2.0 specification. The PPS feature must be configured early in firmware to remap peripheral functions to physical pins, otherwise code will run but peripherals will be inactive.
This page synthesizes distributor pricing, same-brand drop-in alternatives drawn from the PIC32MX3/4/5/6/7 family, and practical design notes not found in the standalone datasheet, helping procurement and firmware engineers evaluate this part efficiently.
Alternatives de remplacement direct pour PIC32MX330F064L-I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC32MX330F064L-I/PT (même facteur de forme et même empreinte) — différant par ADC, Package, DMA Channels, Operating Temperature, MSL Level.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC32MX330F064H-I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX370F064L-I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX430F064L-I/PT
✅ Remplacement direct✓ En stock
$3.45 / unité
Voir la fiche technique →PIC32MX450F256L-I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX470F512L-I/PT
✅ Remplacement direct✓ En stock
$6.32 / unité
Voir la fiche technique →PIC32MX274F256DT-I/PT
✅ Remplacement direct✓ En stock
$3.29 / unité
Voir la fiche technique →PIC32MX330F064L-I/PT Valeurs maximales et caractéristiques électriques
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Speed | 80 MHz |
| Program Flash Memory | 64 KB (64K x 8) |
| Boot Flash | 12 KB (auxiliary) |
| SRAM | 16 KB |
| Operating Voltage Range | 2.3 V to 3.6 V |
| Plage de température de fonctionnement | -40 C to +105 C (Industrial) |
| ADC | 10-bit, up to 1 Msps |
| USB Module | USB 2.0 Full-Speed OTG |
| I2S/SPI Modules | 2 (codec + serial comms) |
| Parallel Master Port (PMP) | Yes (for graphics/parallel peripherals) |
| Charge Time Measurement Unit (CTMU) | Yes (touch sensing, capacitive measurement) |
| DMA Channels | 5 |
| MIPS16e Code Compression | Yes (up to 40% smaller code) |
| Peripheral Pin Select (PPS) | Yes |
| Boîtier | 100-pin TQFP (12x12 mm) |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (per JEDEC J-STD-020) |
| Statut RoHS | Compliant |
Configuration des broches de PIC32MX330F064L-I/PT
| Broche 1 | RG15 — General-purpose I/O |
| Broche 2 | VDD — Supply voltage (3.3V) |
| Broche 3 | RPB0/PWM1 — PPS remappable I/O / PWM output |
| Broche 4 | VSS — Ground |
| Broche 5 | RPB1/PWM2 — PPS remappable I/O / PWM output |
| Broche 6 | RPB2 — PPS remappable I/O |
| Broche 7 | RPB3 — PPS remappable I/O |
| Broche 8 | VSS — Ground |
| Broche 9 | VDD — Supply voltage (3.3V) |
| Broche 10 | OSC1/CLKI — Primary oscillator input |
| Broche 11 | OSC2/CLKO — Primary oscillator output |
| Broche 12 | VSS — Ground |
| Broche 13 | PGED2/RPB4 — ICSP data / PPS I/O |
| Broche 14 | PGEC2/RPB5 — ICSP clock / PPS I/O |
| Broche 15 | VDD — Supply voltage (3.3V) |
| Broche 16 | VBUS — USB VBUS detect |
| Broche 17 | USBID — USB OTG ID |
| Broche 18 | VUSB — USB internal regulator output |
| Broche 19 | D+ — USB D+ data line |
| Broche 20 | D- — USB D- data line |
| Broche 21 | VSS — Ground |
| Broche 22 | RPC1/PMPWR — PMP write strobe / PPS I/O |
| Broche 23 | RPC2/PMPRD — PMP read strobe / PPS I/O |
| Broche 24 | RPC3 — PPS remappable I/O |
| Broche 25 | VDD — Supply voltage (3.3V) |
| Broche 26 | AN0/C2IN+/RPA0 — ADC input / comparator input / PPS I/O |
| Broche 27 | AN1/C2IN-/RPA1 — ADC input / comparator input / PPS I/O |
| Broche 28 | AN2/C1IN+/RPA2 — ADC input / comparator input / PPS I/O |
| Broche 29 | AN3/C1IN-/RPA3 — ADC input / comparator input / PPS I/O |
| Broche 30 | VSS — Ground |
| Broche 31 | AN4/RPA4 — ADC input / PPS I/O |
| Broche 32 | AN5/RPA5 — ADC input / PPS I/O |
| Broche 33 | AN6/RPA6 — ADC input / PPS I/O |
| Broche 34 | AN7/RPA7 — ADC input / PPS I/O |
| Broche 35 | VDD — Supply voltage (3.3V) |
| Broche 36 | AN8/RPB8 — ADC input / PPS I/O |
| Broche 37 | AN9/RPB9 — ADC input / PPS I/O |
| Broche 38 | AN10/RPB10 — ADC input / PPS I/O |
| Broche 39 | AN11/RPB11 — ADC input / PPS I/O |
| Broche 40 | VSS — Ground |
| Broche 41 | AN12/RPB12 — ADC input / PPS I/O |
| Broche 42 | AN13/RPB13 — ADC input / PPS I/O |
| Broche 43 | AN14/RPB14 — ADC input / PPS I/O |
| Broche 44 | AN15/RPB15 — ADC input / PPS I/O |
| Broche 45 | VDD — Supply voltage (3.3V) |
| Broche 46 | RPD0/INT0 — PPS I/O / External interrupt 0 |
| Broche 47 | RPD1/INT1 — PPS I/O / External interrupt 1 |
| Broche 48 | RPD2/INT2 — PPS I/O / External interrupt 2 |
| Broche 49 | RPD3/INT3 — PPS I/O / External interrupt 3 |
| Broche 50 | VSS — Ground |
| Broche 51 | RPD4 — PPS remappable I/O |
| Broche 52 | RPD5 — PPS remappable I/O |
| Broche 53 | RPD6 — PPS remappable I/O |
| Broche 54 | RPD7 — PPS remappable I/O |
| Broche 55 | VDD — Supply voltage (3.3V) |
| Broche 56 | RPF0 — PPS remappable I/O |
| Broche 57 | RPF1 — PPS remappable I/O |
| Broche 58 | RPF2 — PPS remappable I/O |
| Broche 59 | RPF3 — PPS remappable I/O |
| Broche 60 | VSS — Ground |
| Broche 61 | RPF4/PMPD8 — PPS I/O / PMP data 8 |
| Broche 62 | RPF5/PMPD9 — PPS I/O / PMP data 9 |
| Broche 63 | RPF6/PMPD10 — PPS I/O / PMP data 10 |
| Broche 64 | RPF7/PMPD11 — PPS I/O / PMP data 11 |
| Broche 65 | VDD — Supply voltage (3.3V) |
| Broche 66 | RPG0/PMPD0 — PPS I/O / PMP data 0 |
| Broche 67 | RPG1/PMPD1 — PPS I/O / PMP data 1 |
| Broche 68 | RPG2/PMPD2 — PPS I/O / PMP data 2 |
| Broche 69 | RPG3/PMPD3 — PPS I/O / PMP data 3 |
| Broche 70 | VSS — Ground |
| Broche 71 | RPG4/PMPD4 — PPS I/O / PMP data 4 |
| Broche 72 | RPG5/PMPD5 — PPS I/O / PMP data 5 |
| Broche 73 | RPG6/PMPD6 — PPS I/O / PMP data 6 |
| Broche 74 | RPG7/PMPD7 — PPS I/O / PMP data 7 |
| Broche 75 | VDD — Supply voltage (3.3V) |
| Broche 76 | RPF8/PMPD12 — PPS I/O / PMP data 12 |
| Broche 77 | RPF9/PMPD13 — PPS I/O / PMP data 13 |
| Broche 78 | RPF10/PMPCS1 — PPS I/O / PMP chip select 1 |
| Broche 79 | RPF11/PMPCS2 — PPS I/O / PMP chip select 2 |
| Broche 80 | VSS — Ground |
| Broche 81 | RPF12/PMPALE — PPS I/O / PMP address latch enable |
| Broche 82 | RPF13/PMPMCLR — PPS I/O / PMP master clear |
| Broche 83 | RPF14/PMPA0 — PPS I/O / PMP address 0 |
| Broche 84 | RPF15/PMPA1 — PPS I/O / PMP address 1 |
| Broche 85 | VDD — Supply voltage (3.3V) |
| Broche 86 | RPG8/PMPA2 — PPS I/O / PMP address 2 |
| Broche 87 | RPG9/PMPA3 — PPS I/O / PMP address 3 |
| Broche 88 | RPG10/PMPA4 — PPS I/O / PMP address 4 |
| Broche 89 | RPG11/PMPA5 — PPS I/O / PMP address 5 |
| Broche 90 | VSS — Ground |
| Broche 91 | PGED3/RPB6 — ICSP data / PPS I/O |
| Broche 92 | PGEC3/RPB7 — ICSP clock / PPS I/O |
| Broche 93 | VDD — Supply voltage (3.3V) |
| Broche 94 | RPG12 — PPS remappable I/O |
| Broche 95 | RPG13 — PPS remappable I/O |
| Broche 96 | RPG14 — PPS remappable I/O |
| Broche 97 | RPG15 — PPS remappable I/O |
| Broche 98 | VSS — Ground |
| Broche 99 | MCLR — Master clear (reset) |
| Broche 100 | RG14 — General-purpose I/O |
Applications typiques
PIC32MX330F064L-I/PT convient pour 6 applications: USB Audio Class Devices, Industrial HMI Touch Panels, USB Barcode Scanners, Point-of-Sale Terminals, Motor Control Front-Ends, Data Loggers with USB Connectivity.
USB Audio Class Devices
The PIC32MX330F064L-I/PT is well suited for USB audio class 1.0 devices such as USB headphones, USB microphones, and USB DACs. Its 80 MHz MIPS32 M4K core delivers sufficient processing headroom for 24-bit/96 kHz audio streaming at full USB bandwidth, while the integrated USB 2.0 Full-Speed OTG controller and two I2S interfaces allow direct connection to external audio codecs (e.g., Microchip LAN9500A, Cirrus CS43L22) without an external PHY. The 16 KB SRAM holds USB audio descriptors plus 4-5 ms of audio buffering, and the CTMU can be used for touch-button volume controls on the device housing. Engineers should allocate at least 32 KB Flash for the USB stack plus Harmony framework drivers, leaving roughly 30 KB for application logic.
Recommandé
Industrial HMI Touch Panels
The PIC32MX330F064L-I/PT integrates a Charge Time Measurement Unit (CTMU) and Parallel Master Port (PMP), making it ideal for industrial HMI touch panels with capacitive buttons or sliders. The CTMU combined with the 10-bit ADC enables reliable capacitive touch sensing for up to 16 buttons with sub-1 mm positional accuracy, while the PMP directly drives 4.3-inch or 5-inch TFT LCDs at WQVGA (480x272) resolution without an external graphics controller. The 80 MHz core can refresh full-screen graphics at 30+ Hz while simultaneously polling USB host mode for firmware updates. The industrial -40 C to +105 C temperature range allows deployment in factory-floor enclosures without thermal derating.
Recommandé
USB Barcode Scanners
Handheld and fixed-mount USB barcode scanners benefit from the PIC32MX330F064L-I/PT's combination of USB HID device support, fast 80 MHz core, and 64 KB Flash. The integrated USB Full-Speed controller enumerates as an HID Keyboard or HID POS Scanner device without external firmware-side drivers, while the MIPS32 M4K core can decode 1D/2D barcode symbologies (Code128, QR, DataMatrix) from camera sensors over the parallel PMP or SPI interfaces within 50-100 ms per frame. The 16 KB SRAM buffers decoded payloads and image preprocessing intermediate state. Low-power Sleep mode (under 1 mA) extends battery life in portable scanner applications.
Recommandé
Point-of-Sale Terminals
POS terminals rely on the PIC32MX330F064L-I/PT to integrate USB host and device modes simultaneously for connecting to printers, cash drawers, customer displays, and payment PIN pads. The USB-OTG controller supports dual-role operation, allowing the same port to act as a device when connected to a host PC (for configuration) or as a host when driving peripherals. The 5-channel DMA controller offloads data movement between UART (for cash drawer kick-out), SPI (for NFC reader), and I2C (for secure authentication), leaving the CPU free for transaction processing. The industrial temperature range ensures reliable operation in retail environments.
Recommandé
Motor Control Front-Ends
The PIC32MX330F064L-I/PT can serve as a motor-control front-end for small BLDC and stepper motors in appliances and industrial equipment. The Output Compare and PWM modules generate up to six channels of complementary PWM at 80 MHz resolution, suitable for 20 kHz switching frequency motor drive. The 10-bit ADC samples phase currents at 1 Msps for FOC (field-oriented control) with 10 kHz control loop bandwidth, while the CTMU provides BEMF (back-EMF) timing measurements during zero-cross detection. The PMP can drive external gate drivers directly. For more demanding multi-axis motor control, the PIC32MK or dsPIC33 families are recommended.
Recommandé
Data Loggers with USB Connectivity
Portable and industrial data loggers use the PIC32MX330F064L-I/PT to record sensor measurements to external SPI Flash or microSD cards via the PMP, and to offload data via USB MSD class. The 64 KB Flash holds filesystem libraries (FatFs, LittleFS) plus logging firmware, while the 16 KB SRAM buffers sectors during card write operations. The 5-channel DMA streams ADC samples directly to memory without CPU intervention, enabling continuous multi-channel logging at up to 100 kHz aggregate sample rate. The USB-OTG controller enumerates as a Mass Storage Device when connected to a PC, presenting the SD card as a removable drive for easy file retrieval without custom drivers.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC32MX330F064L-I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC32MX370F064L-I/PT | PIC32MX430F064L-I/PT | PIC32MX450F256L-I/PT | PIC32MX470F512L-I/PT | PIC32MX274F256DT-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-TQFP (12x12 mm) | 100-TQFP (12x12 mm) - same | 100-TQFP (12x12 mm) - same | 100-TQFP (12x12 mm) - same | 100-TQFP (12x12 mm) - same | 100-TQFP (12x12 mm) - same |
| Core | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Max CPU Clock | 80 MHz | 80 MHz | 100 MHz | 80 MHz | 80 MHz | 72 MHz |
| Program Flash | 64 KB | 64 KB | 64 KB | 256 KB | 512 KB | 256 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 64 KB | 128 KB | 64 KB |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG |
| Operating Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Temperature Range | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +85 C |
Principaux différenciateurs
- Same package, 4x more memory for code growth (vs PIC32MX450F256L-I/PT)
- Higher CPU clock in same family (vs PIC32MX430F064L-I/PT)
- Lower-power alternative in MX2 family (vs PIC32MX274F256DT-I/PT)
Notes de conception
The PIC32MX330F064L-I/PT requires decoupling on every VDD/VSS pin pair. Place a 100 nF ceramic (X7R) capacitor within 3 mm of each VDD pin, and add a single 10 uF tantalum or ceramic bulk capacitor near the device. For USB applications, add a 4.7 uF capacitor on the VUSB pin. Avoid routing high-speed digital signals (USB, oscillator) directly over the analog AVSS/AVDD plane if a separate analog supply is used, to prevent digital noise from coupling into ADC readings.
Route the 48 MHz USB clock traces with 90 ohm differential impedance, keeping D+ and D- matched within 1 mm. Place the crystal within 5 mm of the OSC1/OSC2 pins, with a ground guard ring around both traces to prevent noise injection. The ICSP programming pins (PGEC2/PGED2 or PGEC3/PGED3) must be brought out to a header or test pad even if not used in production, for in-field firmware updates. Keep the MCLR pin trace short and add a 10 kohm pull-up to VDD as recommended by the manufacturer datasheet.
A common mistake is forgetting to configure the Peripheral Pin Select (PPS) registers in firmware. On reset, all PPS-mapped peripherals are disconnected from physical pins, so UART/SPI/I2C code will compile and start but produce no signals on the scope. Always call the PPS initialization early in main(). Another pitfall is exceeding 3.6 V on any I/O pin when the device is unpowered, which can cause latch-up via the ESD protection diodes. Ensure no external signals drive the MCU while VDD is below 2.0 V.
Informations de conformité
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - the 330 family targets industrial/consumer, not automotive. Use PIC32 variants with -V or -E suffixes for extended temperature ranges if needed.
