SI3241-D-GQ Quad ProSLIC SLIC/Codec 3.3V 100-eTQFP | Skyworks
Référence : SI3241-D-GQ ✓ ActifSI3241-D-GQ Présentation
A SLIC, or subscriber line interface circuit, is the analog front-end block that sits between a public switched telephone network line and the digital voice equipment behind it. In the hierarchy of telecommunications semiconductors, a SLIC is a voice-access interface IC, a subcategory of interface ICs that converts analog line signals into digital PCM bit streams while also providing DC feed, ring generation, hook detection and loop supervision. A combined SLIC/codec such as the SI3241 merges those analog functions with a digital voice codec so a single device can terminate four analog lines and deliver four channels of compressed or uncompressed voice to a host processor.
Key characteristics of this device include four integrated voice channels per package, a 3.3 V supply rail, and multiple host-side serial interfaces, so one IC can replace four discrete line-interface front ends. The silicon is a programmable CMOS design: channel gain, impedance, DC feed and filter behavior are configured through registers rather than external components, which simplifies the analog bill of materials and shortens design-in time for voice gateways, DSL access equipment and VoIP media gateways. Because the same silicon supports both classic PCM and GCI/PCM/SPI transport, the device spans legacy TDM designs as well as modern packet-voice designs.
Architecturally, each of the four channels combines a line-side driver and receiver, the voice codec, and the supervision logic behind a common register interface, with a shared digital backplane to the host. The part is offered in a 100-lead eTQFP with a thermally and electrically connected exposed pad, which lowers package thermal resistance and lets the pad be tied to the ground plane on multilayer boards. The exposed pad must be soldered and connected, otherwise both heat dissipation and the device's ground return degrade. Ordering codes such as -D-GQ denote the die revision, grade and tray packaging, and the -R suffix denotes the same die in tape-and-reel form.
Typical applications include multi-channel VoIP analog terminal adapters, voice-over-PON and DSL voice gateways, digital loop carrier and line-card designs, PBX trunk interfaces, and industrial voice monitoring equipment where four lines must be digitized per board. Because each channel is register-programmable, the same hardware can be reconfigured in the field for different line impedances and country-specific DC feed requirements, which is a significant advantage over fixed analog front ends.
A key design consideration is that the exposed pad and the high line-side drive currents make careful layout mandatory: keep the analog line traces short and isolated from the digital backplane, provide solid decoupling on the 3.3 V rail, and follow the manufacturer's reference layout for the pad connection and the line-side network. A second consideration is that the silicon is mature but still widely supported, so firmware drivers for this ProSLIC family are broadly available.
This page consolidates distributor availability, package and ordering-code detail, drop-in ordering options within the SI3241 family, and practical layout and thermal guidance into a single engineering reference that complements, rather than repeats, the manufacturer datasheet.
Alternatives de remplacement direct pour SI3241-D-GQ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
SI3241-D-FQ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SI3241-GQ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SI3241
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SI3241-D-GQR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SI3241-D-GQ Spécifications
| Product Type | Telecom IC - Subscriber Line Interface Concept (SLIC) / Codec, programmable CMOS |
| Number of Channels | 4 channels |
| Number of Circuits | 4 |
| Tension d'alimentation | 3.3 V |
| Gain | 63 dB |
| Host Interfaces | GCI, PCM, SPI |
| Boîtier | 100-pin eTQFP (14 x 14 mm) with exposed pad |
| Nombre de broches | 100 pins |
| Type de montage | Surface mount |
| Packaging | Tray |
| Ordering Code Suffix | -D-GQ (die revision D, grade G, tray packaging) |
| Reel Ordering Variant | -D-GQR (tape and reel) |
| Exposed Thermal Pad | Yes, exposed pad on eTQFP package |
| Analog Line Functions | Line-side driver/receiver, DC feed, ring generation, loop supervision |
| Datasheet Publication | SI3241 datasheet PDF, published 2013-05-21 |
Guide de configuration des broches du SI3241-D-GQ 100-pin etqfp (14 x 14 mm) with exposed pad
Configuration des broches du SI3241-D-GQ (boîtier 100-pin etqfp (14 x 14 mm) with exposed pad). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour SI3241-D-GQ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
SI3241-D-GQ convient pour 6 applications: VoIP Analog Terminal Adapter (ATA), Voice-over-PON and DSL Voice Gateway, Digital Loop Carrier and Line Card, PBX and Trunk Line Interface, Industrial Voice Monitoring and Test Equipment, PBX VoIP Hybrid and Call-Center Line Card.
VoIP Analog Terminal Adapter (ATA)
The SI3241-D-GQ suits a four-line analog terminal adapter because one package terminates four PSTN lines, digitizes them and presents them to a host processor over PCM, GCI or SPI. Each channel delivers 63 dB of gain with register-configurable line impedance and DC feed, so a single 3.3 V IC replaces four discrete analog front ends and their associated external networks. That consolidation shrinks board area in a compact CPE enclosure and lowers the host port count needed for the digital voice backplane, while the register-programmable channels let one hardware design serve different country line conditions.
Recommandé
Voice-over-PON and DSL Voice Gateway
In a voice gateway that terminates subscriber lines from DSL or fiber access equipment, the SI3241-D-GQ provides four channels of analog line interface and voice codec in a single 100-pin eTQFP (14 x 14 mm) package. The 63 dB gain per channel and programmable CMOS filtering make it practical to match line impedance and DC feed characteristics in firmware rather than with discrete components, which matters when a carrier must support multiple line profiles from the same hardware. Operating from 3.3 V and offering SPI as well as PCM and GCI transports lets the same device interface to either a network processor or a microcontroller-class media engine.
Recommandé
Digital Loop Carrier and Line Card
The SI3241-D-GQ fits digital loop carrier and line-card designs where several analog subscriber lines must be concentrated behind a single processor. Four SLIC/codec channels per 3.3 V IC keep the analog section of a line card compact, and the register-based configuration of DC feed, ring generation and supervision allows the same board to be reconfigured for different line types without a hardware spin. With host-side choices of GCI, PCM and SPI, the device supports both legacy TDM aggregation equipment and newer packet-voice line cards, and the exposed-pad eTQFP keeps thermal performance acceptable in the card's confined airflow.
Recommandé
PBX and Trunk Line Interface
For PBX trunk cards and channelized line interfaces, the SI3241-D-GQ provides four channels of line-side drive, receive, DC feed and voice codec functions from one 100-pin eTQFP device. The 63 dB gain figure and register-controlled filtering let trunk cards normalize a wide variety of analog line conditions, while the SPI or PCM digital backplane delivers the digitized voice to the PBX switching fabric. Consolidating four channels per package reduces the number of components on a crowded trunk card, and the 3.3 V supply simplifies power distribution alongside the switching silicon on the same board.
Recommandé
Industrial Voice Monitoring and Test Equipment
Industrial voice monitoring stations, loop testers and remote line-audio test equipment can use the SI3241-D-GQ to bring four analog lines under software control in one place. Because the channels are register-programmable, a test system can sweep DC feed, ring and supervision conditions and read back loop status without external analog switches, and the diagnostics present in the -F ordering variant of the family extend that visibility to real-time channel status monitoring. The 3.3 V operation and small eTQFP footprint suit dense instrument chassis where each test point needs its own line interface.
Recommandé
PBX VoIP Hybrid and Call-Center Line Card
In a hybrid PBX or call-center line card, the SI3241-D-GQ allows analog PSTN trunks and analog extensions to be digitized alongside SIP endpoints. Four channels per package mean one IC can serve an entire four-port analog module, and the register-programmable line characteristics let the card auto-configure for the extension length, ring cadence and DC feed of each market. Supporting PCM, GCI and SPI makes it equally usable with a dedicated TDM switch fabric or with a host processor that prefers a serial SPI control path, and the 63 dB gain per channel keeps voice levels consistent across mixed analog and digital ports.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour SI3241-D-GQ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SI3241-D-FQ | SI3241-GQ | SI3241 | SI3241-D-GQR |
|---|---|---|---|---|---|
| Package | 100-pin eTQFP (14 x 14 mm) with exposed pad | 100-pin eTQFP (14 x 14 mm) with exposed pad - same | 100-pin eTQFP (14 x 14 mm) with exposed pad - same | 100-pin eTQFP (14 x 14 mm) with exposed pad - same | 100-pin eTQFP (14 x 14 mm) with exposed pad - same |
| Brand | Skyworks Solutions Inc. | Skyworks Solutions Inc. | Skyworks Solutions Inc. | Skyworks Solutions Inc. | Skyworks Solutions Inc. |
| Number of Channels | 4 | 4 | 4 | 4 | 4 |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Product Type | Telecom IC - Subscriber Line Interface Concept (SLIC) / Codec, programmable CMOS | SLIC 4-CH 63dB 3.3V 100-Pin eTQFP | SLIC 4-CH 63dB 3.3V 100-Pin eTQFP | Quad ProSLIC programmable CMOS SLIC/Codec | SLIC 4-CH 63dB 3.3V 100-Pin eTQFP |
Principaux différenciateurs
- Four SLIC/codec channels integrated in one 3.3 V package (vs SI3201-GSR)
- Drop-in option with real-time channel diagnostics (vs SI3241-D-FQ)
- Multiple host-side transport options on the same silicon (vs SI3241 base order code)
- Packaging flexibility within the same footprint (vs SI3241-D-GQR)
Notes de conception
The 100-pin eTQFP exposes a thermal pad on the underside of the package, and that pad is both the primary heat path and the device ground return. Treat it as a mandatory connection: assign a full copper area under the pad, add thermal vias in a via-in-pad or tented pattern per the manufacturer land pattern, and tie the pad to the same ground plane as the ground pins. Leaving the pad unconnected removes the intended heat path and degrades the ground return of the line-side amplifiers, which shows up as noise and hum in the recovered voice signal rather than as an obvious thermal failure.
The line-side section of a ProSLIC is high-gain analog circuitry sitting next to a fast digital backplane, so keep the analog line traces short, avoid routing digital clock and PCM signals beneath the line-side pins, and keep the DC feed and sense resistors away from the digital return path. Place the 3.3 V decoupling capacitors at the supply pins on the same side of the board as the device, and follow the reference layout in the manufacturer datasheet for pin placement, pad geometry and the recommended paste stencil for the exposed pad. Layout to the datasheet land pattern rather than to a generic 100-pin TQFP library footprint.
Two ordering mistakes cause most field problems with this part. First, -GQ is the tray packing code while -GQR is the tape-and-reel code for the same silicon; a reel-fed SMT line that receives a tray-packed reel code will fail at placement. Second, the SI3241 family is register-configured, and a board that is populated with a different die revision or grade suffix than the one validated can change line behaviour, particularly DC feed and supervision thresholds. Record the exact ordering code, die revision and grade on the schematic BOM, and re-verify the line parameters after any substitution.
Informations de conformité
No compliance declarations are stated in the distributor listings for the SI3241-D-GQ. The part is a telecom interface IC rather than an automotive device, so AEC-Q100 qualification does not apply. Check the current manufacturer product page and the material declaration for the exact ordering code before committing to a production release.