SN74AXC4T774BQBR - 4-Bit Dual-Supply Bus Transceiver | Texas Instruments
Référence : SN74AXC4T774BQBR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.75 | $1,75 |
| 10 | $1.55 | $15,50 |
| 100 | $1.25 | $125,00 |
| 500 | $1.05 | $525,00 |
| 1 000 | $0.95 | $950,00 |
| 3 000 | $0.82 | $2 460,00 |
SN74AXC4T774BQBR Présentation
The SN74AXC4T774 belongs to the bus transceiver / level shifter category (a sub-family of voltage level translators within interface ICs / logic ICs). Level translators are interface ICs that allow digital signals to pass between two parts of a system that operate at different supply voltages. They are an essential building block in mixed-voltage designs where low-voltage processors and ASICs must communicate with legacy 1.8 V, 2.5 V, or 3.3 V peripherals, and they enable designers to maintain backwards compatibility while taking advantage of new low-voltage cores.
Key features of the SN74AXC4T774 include a typical data rate of 110 Mbps, 4.4 ns typical propagation delay, partial-power-down support via Ioff, and a control-pin reference (DIR and OE) tied to VCCA for simple GPIO-driven control. The AXC family offers the industry's lowest static power consumption in this class, helping portable and battery-powered designs extend runtime without sacrificing throughput.
The internal architecture uses TI's AXC CMOS technology with one-shot edge accelerators that detect rising or falling edges on the I/O pins and briefly speed up the output drivers to achieve high data rates with low dynamic power. The DIR pin determines signal direction, while OE enables a high-impedance output mode for bus isolation. Both A and B ports support 3.6-V tolerant I/O on the lower-voltage side, simplifying board design.
Typical applications include I2C / SPI / UART bridging between low-voltage SoCs and 3.3 V peripherals, MIPI / camera-serializer voltage translation, SD-card level shifting, and general-purpose GPIO expansion in industrial controllers, wearables, and portable IoT endpoints.
A key design consideration is to always tie the OE pin to VCCA through a pull-up resistor (or to a dedicated GPIO) so that the I/Os enter high-impedance during power-up or power-down, preventing bus contention and back-powering.
This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives in the WQFN-16 footprint, and practical design notes not collated in the manufacturer datasheet alone.
Alternatives de remplacement direct pour SN74AXC4T774BQBR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
SN74AXC4T774RSVR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SN74AXC4T774PW
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
SN74AVC4T774PW
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SN74AXC4T774BQBR.A
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TXS0104EPWR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
NXS0104PW
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
FXLA104UMX
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SN74AXC4T774BQBR Valeurs maximales et caractéristiques électriques
| Fonction | 4-bit dual-supply bus transceiver with configurable voltage translation |
| Number of Channels | 4 |
| Number of Elements | 1 |
| Type de sortie | 3-State |
| Direction Control | Independent DIR and OE inputs |
| Supply Voltage A (VCCA) | 0.65 V to 3.6 V |
| Supply Voltage B (VCCB) | 0.65 V to 3.6 V |
| Débit de données | Up to 110 Mbps (typical) |
| Propagation Delay | 4.4 ns typical |
| Ioff (Partial Power-Down) | Supported |
| Control Pin Reference | DIR and OE referenced to VCCA |
| Température de fonctionnement | -40C to +125C |
| Boîtier | WQFN-16 (BQB) 2.5 x 3.5 mm |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
| Lead-Free / Halogen-Free | Yes / Yes (per TI datasheet family note) |
Configuration des broches de SN74AXC4T774BQBR
| Broche 1 | 1B — Data I/O port B, channel 1 |
| Broche 2 | VCCB — B-port supply voltage (0.65 V to 3.6 V) |
| Broche 3 | 2B — Data I/O port B, channel 2 |
| Broche 4 | GND — Ground |
| Broche 5 | 3B — Data I/O port B, channel 3 |
| Broche 6 | 4B — Data I/O port B, channel 4 |
| Broche 7 | VCCB — B-port supply voltage (0.65 V to 3.6 V) |
| Broche 8 | OE — Output enable, active low, referenced to VCCA |
| Broche 9 | DIR — Direction control, referenced to VCCA |
| Broche 10 | VCCA — A-port supply voltage (0.65 V to 3.6 V) |
| Broche 11 | 1A — Data I/O port A, channel 1 |
| Broche 12 | GND — Ground |
| Broche 13 | 2A — Data I/O port A, channel 2 |
| Broche 14 | VCCA — A-port supply voltage (0.65 V to 3.6 V) |
| Broche 15 | 3A — Data I/O port A, channel 3 |
| Broche 16 | 4A — Data I/O port A, channel 4 |
Applications typiques
SN74AXC4T774BQBR convient pour 6 applications: MIPI / Camera-Serializer Bridge, SD-Card / UHS-I Voltage Translation, I2C / SPI Bus Isolation in Industrial Controllers, Wearable / IoT Sensor Hub, Server / Network Switch GPIO Bridge, FPGA / SoM Multi-Rail Reference Design.
MIPI / Camera-Serializer Bridge
The SN74AXC4T774BQBR's 0.65 V to 3.6 V dual-supply range and 110 Mbps data rate make it a strong fit for bridging MIPI control or low-speed serializer signals between a 0.8 V / 1.0 V application processor and a 1.8 V or 3.3 V camera module. The DIR pin referenced to VCCA lets the SoC dynamically reconfigure bus direction during MIPI command frames, while 3-state outputs allow multiple peripherals to share the same pins during multi-camera muxing. The WQFN-16 (2.5x3.5 mm) footprint is ideal for placement under the BGA of a mobile-class processor, preserving routing channels.
Recommandé
SD-Card / UHS-I Voltage Translation
Portable designs often run the host SoC at 1.0 V or 1.2 V while the SD card operates at 1.8 V (UHS-I) or 3.3 V (legacy). The SN74AXC4T774BQBR can translate 4 data lines and the CMD line between these rails thanks to its independent DIR per group and VCCA-referenced OE. The Ioff partial-power-down feature prevents back-powering of the SoC when the SD slot is depopulated or unpowered, a critical safety property for removable media. Add external pull-ups on the higher-voltage rail to meet SD signaling requirements.
Recommandé
I2C / SPI Bus Isolation in Industrial Controllers
Industrial PLCs and motor controllers frequently need to bridge GPIO, SPI, or I2C between a 3.3 V processor and 5 V or 1.8 V sensor clusters. The SN74AXC4T774BQBR's 0.65 V minimum VCCA and 3.6 V tolerant I/O allow the SoC to sit at any modern voltage, while the OE high-impedance capability lets multiple SN74AXC4T774 buffers sit on the same shared bus when a multiplexer is needed. Industrial temperature range (-40C to +125C) ensures operation across factory-floor thermal ranges, and the WQFN-16 footprint is small enough for dense backplanes.
Recommandé
Wearable / IoT Sensor Hub
Battery-powered wearables combine a low-voltage BLE SoC (often 0.8 V core) with 1.8 V IMU, 3.3 V LED driver, and 1.2 V display controller. The SN74AXC4T774BQBR's typical quiescent current is in the low uA range, preserving battery life across always-on sensor hubs. The WQFN-16 (2.5x3.5 mm) footprint occupies only ~8.75 mm^2 of board area, leaving room for coin-cell or Li-ion form factors. Ioff is critical during deep-sleep power gating: external 3.3 V rails can collapse without back-driving the SoC.
Recommandé
Server / Network Switch GPIO Bridge
Datacenter switches and NIC cards run management controllers (BMCs) at 1.0 V or 1.2 V while coordinating with 3.3 V management LEDs, SFP+ I/O, and I2C EEPROMs at 5 V (via pull-up). The SN74AXC4T774BQBR can bridge 4 of these rails simultaneously, with DIR controlled by a 1.8 V-tolerant GPIO. Industrial temperature grade supports the server Inlet Thermal range, and the WQFN-16 package enables placement adjacent to high-density BMC pin headers. The 110 Mbps capability is comfortably above any GPIO or I2C management requirement.
Recommandé
FPGA / SoM Multi-Rail Reference Design
Modern FPGA SoMs (System-on-Module) integrate core rails at 0.85 V or 0.9 V with bank I/O at 1.2 V, 1.8 V, 2.5 V, and 3.3 V depending on the FPGA family. The SN74AXC4T774BQBR gives the carrier board designer a single small-footprint option to translate four signals between any two of these rails, simplifying BOM management. The DIR-referenced-to-VCCA architecture means only the lower-voltage side CPU needs to drive control bits; the higher-voltage side is automatically biased. RoHS compliance and high-volume availability make it ideal for production carrier boards.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour SN74AXC4T774BQBR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SN74AXC4T774RSVR | SN74AVC4T774PW | TXS0104EPWR | NXS0104PW | FXLA104UMX |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | onsemi |
| Package | WQFN-16 (BQB) 2.5x3.5 mm | UQFN-16 (RSV) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-14 (PW) | UMLP-16 (UQFN) |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Min VCCA | 0.65 V | 0.65 V | 1.2 V | 1.65 V | 1.65 V | 0.9 V |
| Max Data Rate | 110 Mbps | 110 Mbps | 380 Mbps | 24 Mbps | 20 Mbps | 100 Mbps |
| Direction Control | DIR + OE (VCCA ref) | DIR + OE (VCCA ref) | DIR + OE (VCCA ref) | Auto-bidirectional | Auto-bidirectional | Auto-bidirectional |
| Output Type | 3-State | 3-State | 3-State | Open-drain + pull-up | Open-drain + pull-up | 3-State |
| Ioff / Power-Down | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +85C |
Principaux différenciateurs
- Lowest minimum VCCA in its class (vs SN74AVC4T774PW)
- Smallest TI footprint option for this function (vs SN74AXC4T774PW)
- 10x higher data rate than open-drain competitors (vs TXS0104EPWR)
Notes de conception
Always tie OE to VCCA through a pull-up resistor (typically 100 kohm) so that during power-up or power-down the outputs enter high-impedance. According to TI's SN74AXC4T774 datasheet application section, the OE pin is referenced to VCCA; if VCCA is off, OE floats low - which is desirable for high-Z - but explicit external pull-up ensures deterministic behavior across all power-up sequencing scenarios. Add 0.1 uF decoupling on each VCCA and VCCB pin within 2 mm of the package.
The AXC family supports VCCA down to 0.65 V, but the DIR and OE control pins are also referenced to VCCA. Never drive DIR or OE from a higher-voltage rail than VCCA, or excessive current flows into the reference structure. Estimated: if DIR is driven at 3.3 V while VCCA is at 1.8 V, the absolute-difference rating of VCCA + 0.5 V is exceeded, risking parametric drift or latch-up. Use a divider or a buffer if your control source is on a different rail.
The WQFN-16 (BQB) has an exposed thermal pad that MUST be soldered to the PCB for mechanical reliability. Recommended PCB layout: 4 thermal vias in a 0.3 mm-pitch grid under the EP connected to the ground plane, and route all 16 signals with 50-ohm controlled impedance if the topology supports it. Place the device near the SoC pads to minimize stub length - long stubs on the lower-voltage side are the dominant source of signal-integrity violations at 110 Mbps.
Informations de conformité
Standard -40C to +125C industrial grade; for AEC-Q100 automotive qualification choose SN74AXC4T774-Q1 variant. RoHS and REACH compliance confirmed by TI product family documentation.
