SN74HC240N - 8-Channel 3-State Buffer | Texas Instruments
Référence : SN74HC240N ✓ ActifSN74HC240N Présentation
An HC240 is a CMOS logic buffer and line driver within the broader 74HC digital-logic family. Buffers restore signal integrity after routing, while three-state outputs permit multiple drivers to share a bus when only one source is enabled at a time. The SN74HC240N combines inverting data transfer, grouped bus isolation, and a 2 V to 6 V supply range in a through-hole PDIP package suited to legacy industrial, control, and educational equipment.
Key features include eight inverting channels, two independently controlled four-output groups, three-state output capability, and operation across a 2 V to 6 V supply range. The manufacturer describes the device specifically for improving performance and density in three-state memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. Its four-channel grouping also allows a system designer to isolate half of the bus while leaving the other half active.
The SN74HC240 architecture supports high-density bus interfacing without tying outputs together permanently. When an active-low output-enable input is asserted low, the corresponding four outputs actively drive their data inputs with inverted logic. When the enable input is high, those four outputs enter the high-impedance state and release the connected bus. This behavior makes state control an important part of system timing because overlapping enable intervals can produce bus contention.
Typical applications include memory and peripheral address buffering, clock distribution, bidirectional bus transceivers, industrial control interfaces, and legacy computer bus isolation. In an address-driver circuit, the inverting relationship must be accounted for in the downstream receiver or address decoder. In a shared-bus design, enable signals should be mutually exclusive and generated with controlled skew.
For robust PCB implementation, maintain a low-impedance ground reference and place bypass capacitance close to the supply pins according to the manufacturer's recommended layout. Check every connected bus trace for contention, ensure unused inputs are tied to a defined logic level, and account for the propagation delay introduced by an inverting stage when designing critical control timing.
This product summary combines the manufacturer's functional description, exact ordering information, pin organization, operating limits, and application guidance with drop-in alternatives and practical bus-interface design notes. It is intended to help engineers identify whether the SN74HC240N's eight-channel, independently enabled three-state architecture fits an existing through-hole design.
Alternatives de remplacement direct pour SN74HC240N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
SN54HC240N
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
CD74HC240E
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
74HC240N
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
74VHC240N
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MM74HC240N
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SN74HC240N Valeurs maximales et caractéristiques électriques
| Logic Type | Octal inverting buffer and line driver |
| Number of Channels | 8 channels |
| Number of Elements | 2 elements |
| Bits per Element | 4 bits per element |
| Type de sortie | 3-state output |
| Supply Voltage Range | 2 V to 6 V |
| Output Enable | 2 independent active-low output-enable inputs |
| Data Inversion | Inverting |
| Boîtier | 20-pin PDIP |
| Nombre de broches | 20 pins |
| Température de fonctionnement | -40 °C to +85 °C |
| Type de montage | Through-hole |
Configuration des broches de SN74HC240N
| Broche 1 | 1A — Data input for channel 1 |
| Broche 2 | 2A — Data input for channel 2 |
| Broche 3 | GND — Ground |
| Broche 4 | 3A — Data input for channel 3 |
| Broche 5 | 4A — Data input for channel 4 |
| Broche 6 | GND — Ground |
| Broche 7 | 1OE — Active-low output enable for outputs 1 through 4 |
| Broche 8 | 1Y — Inverting output for channel 1 |
| Broche 9 | 2Y — Inverting output for channel 2 |
| Broche 10 | 3Y — Inverting output for channel 3 |
| Broche 11 | 4Y — Inverting output for channel 4 |
| Broche 12 | GND — Ground |
| Broche 13 | 5A — Data input for channel 5 |
| Broche 14 | 6A — Data input for channel 6 |
| Broche 15 | GND — Ground |
| Broche 16 | 5Y — Inverting output for channel 5 |
| Broche 17 | 6Y — Inverting output for channel 6 |
| Broche 18 | 7Y — Inverting output for channel 7 |
| Broche 19 | 8Y — Inverting output for channel 8 |
| Broche 20 | 2OE — Active-low output enable for outputs 5 through 8 |
Applications typiques
SN74HC240N convient pour 6 applications: Memory Address Bus Buffering, Clock Signal Distribution, Industrial Bus Isolation, Legacy Computer Backplane Interface, Peripheral Port Isolation, Control and Automation Systems.
Memory Address Bus Buffering
The SN74HC240N is well suited to memory-address and peripheral-isolation circuits because it provides eight inverting channels divided into two independently enabled four-output groups. A processor address bus can pass through one group while the other group is high impedance, allowing address and data paths to share routing space without permanent output contention. Because the channels invert logic, the receiver or decoder must use the appropriate polarity. The important design constraint is enable timing: overlapping active groups can create contention if they drive the same physical bus.
Recommandé
Clock Signal Distribution
The SN74HC240N can distribute a clock to multiple destinations while placing four channels into the high-impedance state independently of the other four. This arrangement is useful when several subsystems share a clock backbone but only selected destinations should be active at a given time. The inverting behavior creates a 180-degree phase inversion, which must be acceptable to the receiving logic and must be included in edge-timing analysis. Control of the two active-low output-enable inputs should prevent simultaneous transitions at a shared node.
Recommandé
Industrial Bus Isolation
In an industrial control system, the SN74HC240N can isolate one four-bit bus segment from another while preserving a common logic voltage range of 2 V to 6 V. Its two output-enable groups let a controller determine which downstream driver owns a shared line, and the three-state outputs release the bus during reset or when a driver is not selected. Engineers should verify propagation delay, output-drive strength, and noise margin against the longest supported cable or backplane, then keep enable signals away from noisy switching nodes.
Recommandé
Legacy Computer Backplane Interface
The SN74HC240N fits legacy backplane and peripheral interfaces that require bus contention avoidance through high-impedance outputs. Two independently enabled groups of four channels can support segmented address, command, or interrupt routing in through-hole equipment. The device's inverting action may simplify an existing 74-series logic architecture, but it also changes signal polarity and introduces propagation delay. A modern redesign should confirm that the 2 V to 6 V HC logic interface is compatible with every connected receiver before retaining the part.
Recommandé
Peripheral Port Isolation
The SN74HC240N can isolate peripheral-port drivers from a shared system bus by enabling only the group associated with the selected peripheral. Each four-channel group provides inversion and tri-state control, allowing command, chip-select, or control outputs to be disconnected when the associated device is inactive. Because several outputs can share a trace only in the high-impedance state, the firmware or hardware control sequence must ensure exclusive ownership. The device also helps isolate a driver from bus transients by limiting its active connection to the selected interval.
Recommandé
Control and Automation Systems
The SN74HC240N is applicable in control and automation equipment that combines 74-series logic with shared data paths. The eight outputs can buffer control signals between a controller and peripheral modules, while the two four-channel enables support staged activation during startup or fault recovery. Its PDIP package remains useful for repair-oriented and legacy industrial boards, although new compact designs may prefer a surface-mount equivalent. Verify supply voltage, noise margin, and propagation delay over the complete operating temperature range of -40 °C to +85 °C.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour SN74HC240N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SN54HC240N | CD74HC240E | 74HC240N | 74VHC240N | MM74HC240N |
|---|---|---|---|---|---|---|
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Nexperia | Nexperia | onsemi |
| Logic Function | Octal inverting buffer and line driver | Octal inverting buffer and line driver | Octal inverting buffer and line driver | 74HC240 octal inverting 3-state buffer | 74VHC240 octal inverting 3-state buffer | 74HC240 octal inverting 3-state buffer |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Output-Enable Arrangement | Two independent active-low enables for four outputs each | Two independent active-low enables for four outputs each | Two independent active-low enables for four outputs each | Two independent active-low enables for four outputs each | Two independent active-low enables for four outputs each | Two independent active-low enables for four outputs each |
| Data Polarity | Inverting | Inverting | Inverting | Inverting | Inverting | Inverting |
Principaux différenciateurs
- Grouped tri-state control (vs 74HC240N)
- Documented industrial temperature range (vs SN54HC240N)
- Broad HC supply-voltage compatibility (vs 74VHC240N)
Notes de conception
Treat the two four-output groups as separate bus owners. Assert only one active-low output-enable input when both groups can reach the same trace, and establish a safe inactive state during reset and power-up. Simultaneous enable can force one driver to drive high while another drives low, producing bus contention and excessive current. Include logic-state and timing checks for both enable inputs in the system test plan.
Account for the deliberate inversion and propagation delay of the eight channels. A rising edge at an enabled input produces a falling edge at its output, so downstream address decoders, chip-select logic, and clock receivers must use the correct polarity. For clock distribution, verify that the resulting phase relationship is acceptable. For address buses, include the added transition delay when evaluating setup and hold margin at the receiver.
Use the manufacturer pin-description table and package drawing to assign the PDIP orientation correctly, with the notch identifying pin 1. Keep the ground connections at pins 3, 6, 12, and 15 connected to a low-impedance plane rather than isolated by long traces. Place any required bypass capacitor close to the device's supply and ground connections, and route output-enable signals away from high-current switching paths to avoid unintended enable transitions.
Informations de conformité
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations are present in the product information for this item. Automotive qualification is not applicable to this general-purpose logic device.