TLE9461ESV33XUMA1 - OPTIREG Lite SBC, CAN FD, 5V/3.3V LDO | Infineon
Référence : TLE9461ESV33XUMA1 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $3.18 | $3,18 |
| 10 | $2.86 | $28,60 |
| 100 | $2.45 | $245,00 |
| 500 | $2.15 | $1 075,00 |
| 1 000 | $1.91 | $1 910,00 |
TLE9461ESV33XUMA1 Présentation
What is a System Basis Chip? An SBC is a multi-functional power and communication IC that consolidates the functions previously served by separate components: a voltage regulator, a bus transceiver (such as CAN, LIN, or FlexRay), reset generation, watchdog supervision, and sometimes wake-up logic. SBCs sit between the vehicle battery and the microcontroller in the system hierarchy: SBC -> power management IC -> automotive semiconductor. By merging these functions into one die, an SBC reduces PCB area, lowers quiescent current, and simplifies ASIL functional-safety design by providing a single, characterized supply source for the MCU.
Key features include a 5 V LDO delivering up to 250 mA for the host microcontroller, a separate 3.3 V LDO rail, hardware and software watchdog modes, a CAN FD transceiver meeting ISO 11898-1, under-voltage and over-voltage detection, and thermal shutdown. The exposed pad (EP) of the PG-TSDSO-24-1 package gives a low thermal resistance to the PCB, allowing the device to drive 250 mA continuously without a heatsink in typical ambient conditions.
The architecture uses a high-side DMOS power switch for the 5 V LDO, a low-quiescent linear regulator for the 3.3 V rail, and a differential CAN transceiver compliant with ISO 11898-2. The CAN FD interface supports bit rates up to 5 Mbps in the data phase, while the integrated slope control minimizes EMI on the bus.
Typical applications include automotive body control modules, CAN gateway ECUs, HVAC controllers, seat and lighting modules, and BCM power management. It is well suited as a supply-and-transceiver companion to Infineon AURIX and other 5 V microcontrollers used in CAN networks.
When designing with this device, ensure the exposed pad has sufficient copper pour (typically 1 cm x 1 cm on outer layers) and that the bus termination is 120 Ω at the cable ends. Use Infineon’s configuration tool to set watchdog timing, fail-safe behavior, and wake sources before firmware bring-up.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the Infineon datasheet, giving automotive engineers a single point of comparison for OPTIREG Lite SBC selection.
Alternatives de remplacement direct pour TLE9461ESV33XUMA1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec TLE9461ESV33XUMA1 (même facteur de forme et même empreinte) — différant par Package, Product Type, Watchdog.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
TLE9461ESV33XUMA2
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLE9462ESV33XUMA1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLE9471ESV33XUMA1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLE92633BQXXUMA2
✅ Remplacement direct✓ En stock
$3.78 / unité
Voir la fiche technique →TLE95613QXXUMA1
✅ Remplacement direct✓ En stock
$3.78 / unité
Voir la fiche technique →TLE9461ESV33XUMA1 Spécifications
| Product Type | System Basis Chip (SBC) - OPTIREG Lite |
| Boîtier | PG-TSDSO-24-1 (24-pin TSDSO with exposed pad) |
| CAN Transceiver | CAN FD, up to 5 Mbps, ISO 11898-1 compliant |
| 5 V LDO Output Current | 250 mA |
| 3.3 V LDO Output | Yes, integrated |
| Supply Voltage (VBAT) | 5.5 V to 28 V (jump start tolerant per data) |
| Watchdog | Yes (hardware and software modes) |
| Wake Inputs | Yes (CAN and pin wake) |
| Reset Output | Yes, with adjustable threshold |
| Température de fonctionnement | -40 C to +150 C (junction) |
| Type de montage | Surface Mount |
| Niveau MSL | MSL3 (per JEDEC J-STD-020) |
| Statut RoHS | Compliant |
| AEC-Q100 | Qualified (automotive grade) |
| Moisture Sensitivity | MSL3 |
Configuration des broches de TLE9461ESV33XUMA1
| Broche 1 | VS — Battery supply input (VBAT) |
| Broche 2 | VCC5V — 5 V LDO output |
| Broche 3 | VCC3V3 — 3.3 V LDO output |
| Broche 4 | GND — Ground |
| Broche 5 | CANH — CAN high bus line |
| Broche 6 | CANL — CAN low bus line |
| Broche 7 | WK1 — Wake input 1 |
| Broche 8 | WK2 — Wake input 2 |
| Broche 9 | EN — Enable input |
| Broche 10 | RST — Reset output to MCU |
| Broche 11 | INT — Interrupt output |
| Broche 12 | WDO — Watchdog output |
| Broche 13 | TXD — CAN transmit data from MCU |
| Broche 14 | RXD — CAN receive data to MCU |
| Broche 15 | VDDIO — I/O supply reference |
| Broche 16 | MODE — Mode select (Normal/Sleep) |
| Broche 17 | TIMER — Watchdog timer adjust |
| Broche 18 | NC — Not connected |
| Broche 19 | NC — Not connected |
| Broche 20 | SENSE — Current sense output |
| Broche 21 | GND2 — Ground |
| Broche 22 | VBAT_SENSE — Battery voltage sense |
| Broche 23 | NC — Not connected |
| Broche 24 | NC — Not connected |
Applications typiques
TLE9461ESV33XUMA1 convient pour 6 applications: Automotive Body Control Module (BCM), CAN Gateway ECU, HVAC Climate Control Module, Seat Control and Comfort Module, Interior Lighting Module, Zonal ECU / Domain Controller.
Automotive Body Control Module (BCM)
The TLE9461ESV33XUMA1 fits body control modules because it integrates the 5 V MCU supply, a 3.3 V sensor rail, and a CAN FD transceiver in a single 24-pin TSDSO. The 250 mA 5 V LDO supports an AURIX TC2xx or TC3xx host MCU plus peripheral logic without an external regulator. Compared with a discrete design of CAN IC + 2 LDOs + reset, the SBC saves roughly 60% of the power-section PCB area, and the 5 Mbps CAN FD allows BCMs to handle larger diagnostic message payloads in modern vehicles. The integrated watchdog and reset with selectable threshold also reduce external component count for ASIL-B functional safety.
Recommandé
CAN Gateway ECU
The TLE9461ESV33XUMA1 is a natural fit for CAN-to-CAN or CAN-to-Ethernet gateway ECUs where the host MCU needs a clean 5 V supply and the bus interface is CAN FD. The 5 Mbps CAN FD data rate is required to bridge between modern and legacy CAN segments without bottlenecks. The exposed-pad TSDSO-24 package keeps the thermal footprint under 1 cm^2 even at 250 mA load, which is essential for compact gateway hardware mounted behind the instrument cluster. The hardware watchdog can be configured to reset the gateway if the host MCU firmware hangs during a routing task, supporting ASIL-A safety goals.
Recommandé
HVAC Climate Control Module
HVAC modules need a regulated 5 V supply for the MCU, a 3.3 V rail for sensors and display drivers, and a CAN interface for body-network communication - exactly what the TLE9461ESV33XUMA1 provides. The 5 V LDO delivers 250 mA, more than enough for an HVAC MCU plus a small TFT or segment LCD driver. The integrated watchdog prevents climate control from locking up the bus, and the low quiescent current in sleep mode keeps parking-drain below 100 uA. Compared with a discrete solution, this SBC reduces the BOM count by 3-4 parts and improves EMC behavior by sharing one ground reference across the supply and bus circuits.
Recommandé
Seat Control and Comfort Module
Seat control modules with memory, heating, and ventilation benefit from the TLE9461ESV33XUMA1's combined 5 V and 3.3 V rails plus CAN FD. The 250 mA 5 V output can supply the seat MCU and the LIN/CCP slave transceivers, while the 3.3 V LDO powers the position-sensor ADCs and EEPROM. The watchdog with window mode ensures that any MCU lockup triggers a reset and brings the seat to a safe position. The PG-TSDSO-24-1 exposed-pad package allows the module to be mounted in the seat frame where convection cooling is limited, since the EP sinks heat directly into the chassis ground plane.
Recommandé
Interior Lighting Module
Interior lighting modules with LED matrix and ambient-color features use the TLE9461ESV33XUMA1 as a power and bus interface. The 5 V LDO powers the LED driver MCU and the 3.3 V LDO supports addressable LED strings. The CAN FD bus handles dynamic color-command frames at 5 Mbps, supporting the trend toward richer ambient lighting. The exposed-pad package keeps the SBC within the small footprint typical of door-mounted lighting ECUs. Compared with discrete LDOs, the integrated approach reduces standby drain and helps meet < 100 uA dark-current targets required by automakers.
Recommandé
Zonal ECU / Domain Controller
The TLE9461ESV33XUMA1 is well suited to zonal ECUs consolidating multiple CAN segments in modern E/E architectures. The CAN FD transceiver at 5 Mbps handles aggregated sensor data from the zone, and the two LDOs (5 V / 3.3 V) cover the host MCU and the zonal sensor interface. The exposed-pad TSDSO-24-1 package is small enough to fit in the constrained space of a zonal module mounted near the wheelhouse or seat base. The integrated watchdog supports fail-safe behavior in case the host MCU loses communication with the central vehicle computer, which is a key requirement for zonal architectures with ASIL-B goals.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TLE9461ESV33XUMA1 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TLE9461ESV33XUMA2 | TLE9462ESV33XUMA1 | TLE9471ESV33XUMA1 | TLE92633BQXXUMA2 | TLE95613QXXUMA1 |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TSDSO-24-1 | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same | PG-TSDSO-24 (variant) - same family | PG-TSDSO-24-1 - same |
| 5 V LDO Output Current | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA |
| 3.3 V LDO | Yes | Yes | Yes | Yes | Configurable | Yes |
| CAN FD Data Rate | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps |
| Watchdog | HW + SW modes | HW + SW modes | HW + SW modes | HW + SW modes | HW + SW modes | HW + SW modes |
| LIN Transceiver | No | No | No | Yes | No | Yes |
| AEC-Q100 | Qualified | Qualified | Qualified | Qualified | Qualified | Qualified |
Principaux différenciateurs
- Same-family newer revision drop-in (vs TLE9461ESV33XUMA2)
- Selectable CAN wake-up for partial networking (vs TLE9462ESV33XUMA1)
- Adds LIN transceiver without changing footprint (vs TLE9471ESV33XUMA1)
- Multi-rail SBC for body zonal controllers (vs TLE95613QXXUMA1)
Notes de conception
The PG-TSDSO-24-1 package uses an exposed pad to dissipate heat from the 5 V LDO. At 250 mA load with VIN = 12 V and VOUT = 5 V, dissipation is roughly (12 - 5) * 0.25 = 1.75 W. The exposed pad must be soldered to a ground copper pour of at least 1 cm^2 on the top layer, with thermal vias to inner/outer ground planes. Without adequate copper, junction temperature can exceed 150 C and trigger thermal shutdown, especially in door-mounted or seat-mounted modules with limited airflow.
Route the CANH and CANL traces as a differential pair with 120 Ω characteristic impedance, keeping them length-matched within 5 mm. Place a 0603-sized common-mode choke within 10 mm of the CAN connector to pass OEM-conducted emissions tests, and use a split termination (60 Ω + 60 Ω + 4.7 nF to ground) at the bus ends to suppress common-mode noise. Keep the CAN traces away from switching nodes such as the 5 V LDO input inductor area to avoid coupling.
Do not float the MODE pin - it must be tied to a defined logic level to select Normal or Sleep mode. Leaving it open can cause indeterminate behavior at power-up. The WK1/WK2 wake inputs require external debounce; a 100 nF capacitor to ground plus a 10 kΩ pull-up to VCC5V gives reliable wake detection in noisy automotive environments. Finally, the RST pin is open-drain and requires an external pull-up of at least 4.7 kΩ to VCC5V.
The CAN FD bus is a major EMI source in automotive designs. Use shielded twisted-pair cable for the CAN bus and place a ferrite bead on the VBAT supply to the SBC to suppress conducted noise from injecting back into the battery rail. The internal slope control of the TLE9461ESV33XUMA1 helps reduce high-frequency harmonics, but adding a 22 pF capacitor between CANH and CANL further slows the edge rate if the OEM requires CISPR 25 Class 5 compliance.
Informations de conformité
RoHS and REACH compliant per Infineon product page. AEC-Q100 qualified for automotive use. Lead-free finish. Halogen-free per JEDEC JS709.
