TPS51640RSLR - 2+1 IMVP7 CPU/GPU Controller | Texas Instruments
Référence : TPS51640RSLR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.36 | $336,00 |
| 500 | $3.02 | $1 510,00 |
| 1 000 | $2.69 | $2 690,00 |
| 3 000 | $2.35 | $7 050,00 |
TPS51640RSLR Présentation
An SVID (Serial VID) interface and an IMVP7 (Intel Mobile Voltage Positioning 7) controller is a digital protocol that lets a CPU or GPU set its own operating voltage on the fly. The 2+1 phase topology distributes thermal stress across three inductor-switch pairs for the CPU rail (sharing up to ~80A of load with proper external MOSFETs) while a single phase handles graphics output. A D-CAP+ modulator with on-resistance current sensing eliminates the need for external shunt resistors, reducing BOM cost and PCB area. The integrated bootstrap switch and driver-less architecture require external high-side and low-side MOSFETs.
Key features include 0.5% Vout accuracy, selectable 250 kHz to 1.5 MHz per-phase switching frequency, dynamic phase shedding from 3-phase to 1-phase to optimize light-load efficiency, programmable soft-start, and comprehensive protection including OVP, UVP, OCP and thermal shutdown. The thermal pad and 48-pin QFN layout provide a theta-JA near 28 C/W on a 4-layer PCB.
Typical applications include IMVP7-compliant mobile computing platforms, ultrabook main rails, Ultrabook/Chromebook CPU VCORE rails, and 2-in-1 convertible tablet main rails. Industrial variants may use the controller with appropriate external components for any multi-phase CPU/GPU voltage regulation scheme that supports SVID protocol.
When designing with the TPS51640RSLR, current-loop compensation components (R-C-C) must be selected based on the per-phase inductance and selected switching frequency. The SVID address and VR enable polarity must be configured during platform design with the CPU vendor. The TPS51640RSLR is functionally identical to the TPS51640A (which has different boot voltage specifications per datasheet).
Alternatives de remplacement direct pour TPS51640RSLR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
TPS51640ARSLR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS59640RSLR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS59641RSLR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS51640RSLR Valeurs maximales et caractéristiques électriques
| Topologie | 2+1 phase step-down (3-phase CPU + 1-phase GPU controller) |
| Plage de tension de sortie | 0.25 V to 1.5 V (programmable via SVID) |
| Output Voltage Accuracy | 0.5% (across load, line and temperature) |
| Plage de tension d'entrée | 4.5 V to 28 V |
| Fréquence de commutation | 250 kHz to 1.5 MHz per phase (programmable) |
| Number of Phases | 2+1 (two rails; CPU up to 3 phases, GPU single phase) |
| Modulation Scheme | D-CAP+ with on-resistance current sensing |
| Communication Interface | SVID (Serial VID) for IMVP7 compliance |
| Tension de référence | 1.0 V internal reference |
| Démarrage progressif | Programmable |
| Température de fonctionnement | -10 C to +105 C |
| Boîtier | 48-pin QFN (RSL), 7x7 mm with thermal pad |
| Type de montage | Surface Mount |
| Niveau MSL | 2 |
| Statut RoHS | Compliant |
| Protections | OVP, UVP, OCP, Thermal Shutdown |
Configuration des broches de TPS51640RSLR
| Broche 1 | VCC — Internal LDO bypass / 5V analog supply |
| Broche 2 | EN — Active-high controller enable |
| Broche 3 | SVID_DATA — SVID serial data (open-drain) |
| Broche 4 | SVID_CLK — SVID serial clock (input) |
| Broche 5 | SVID_ALERT — SVID alert from CPU (open-drain) |
| Broche 6 | VR_HOT — Thermal hot flag output |
| Broche 7 | VSNS_CPU — Vout sense for CPU rail (negative) |
| Broche 8 | VSNS_CPU_P — Vout sense for CPU rail (positive) |
| Broche 9 | CS1N — Channel 1 current sense negative |
| Broche 10 | CS1P — Channel 1 current sense positive |
| Broche 11 | BOOT1 — Phase 1 bootstrap |
| Broche 12 | UGATE1 — Phase 1 high-side gate drive |
| Broche 13 | LGATE1 — Phase 1 low-side gate drive |
| Broche 14 | VSW1 — Phase 1 switch node |
| Broche 15 | PGND1 — Phase 1 power ground |
| Broche 16 | BOOT2 — Phase 2 bootstrap |
| Broche 17 | UGATE2 — Phase 2 high-side gate drive |
| Broche 18 | LGATE2 — Phase 2 low-side gate drive |
| Broche 19 | VSW2 — Phase 2 switch node |
| Broche 20 | PGND2 — Phase 2 power ground |
| Broche 21 | BOOT3 — Phase 3 bootstrap (CPU rail phase 3) |
| Broche 22 | UGATE3 — Phase 3 high-side gate drive |
| Broche 23 | LGATE3 — Phase 3 low-side gate drive |
| Broche 24 | VSW3 — Phase 3 switch node |
| Broche 25 | PGND3 — Phase 3 power ground |
| Broche 26 | VID_SET — External VID configuration |
| Broche 27 | VR_RDY — Power-good output to CPU |
| Broche 28 | OVP — Over-voltage protection input |
| Broche 29 | UVP — Under-voltage protection input |
| Broche 30 | OCP — Over-current protection threshold |
| Broche 31 | ILIM — Per-phase current-limit setting |
| Broche 32 | FREQ — Switching frequency trim resistor |
| Broche 33 | RT — Timing resistor (frequency set) |
| Broche 34 | COMP1 — Compensation node phase 1 |
| Broche 35 | COMP2 — Compensation node phase 2 |
| Broche 36 | COMP3 — Compensation node phase 3 |
| Broche 37 | VSNS_GPU — Vout sense for GPU rail (negative) |
| Broche 38 | VSNS_GPU_P — Vout sense for GPU rail (positive) |
| Broche 39 | BOOT4 — GPU rail phase bootstrap |
| Broche 40 | UGATE4 — GPU rail high-side gate drive |
| Broche 41 | LGATE4 — GPU rail low-side gate drive |
| Broche 42 | VSW4 — GPU rail switch node |
| Broche 43 | PGND4 — GPU rail power ground |
| Broche 44 | REF — Internal reference 1.0V bypass |
| Broche 45 | AGND — Analog ground |
| Broche 46 | TRK — Soft-start / voltage tracking |
| Broche 47 | SET5 — VID table select |
| Broche 48 | PAD — Thermal pad / PGND (must be soldered) |
Applications typiques
TPS51640RSLR convient pour 6 applications: IMVP7 Ultrabook CPU VCORE Rail, Mobile GPU Voltage Regulator, 2-in-1 Tablet Main Rail, Intel Y/U-Series Notebook Power, Industrial IMVP7-Compatible Embedded Platform, Server Memory/Voltage-Positioned Auxiliary Rail.
IMVP7 Ultrabook CPU VCORE Rail
The TPS51640RSLR is purpose-built for IMVP7-compliant Intel ultrabook CPU rails. With 0.5% Vout accuracy, SVID command compliance, and a 2+1 phase topology the part shares three phases across the CPU rail so each phase handles ~30A of sub-1V load. D-CAP+ modulation delivers sub-100 ns transient response with no external compensation network, which is critical when the CPU jumps between C-states. Phase shedding from 3 to 1 phase holds light-load efficiency above 80% at 0.7V Vout, extending battery run-time during idle.
Recommandé
Mobile GPU Voltage Regulator
The second rail of the TPS51640RSLR drives integrated Intel GPUs in a single-phase configuration. The 0.25V minimum output enables sub-1V GPU VCORE operation needed for energy-efficient graphics. By sharing the same SVID bus the GPU rail coordinates load-line with the CPU rail so transient events on one rail do not sag the other. Internal adaptive on-resistance current sensing removes external shunt resistors, reducing PCB area - a meaningful gain for sub-2 mm Z-height ultrabook chassis.
Recommandé
2-in-1 Tablet Main Rail
The 2+1 architecture of the TPS51640RSLR simultaneously powers the SoC and its companion GPU in compact 2-in-1 tablet and Chromebook designs. With switching frequency programmable from 250 kHz to 1.5 MHz per phase, the designer can shrink output inductors to 0.47 uH to fit the 4 mm x 4 mm CPU land area. The -10 C to +105 C operating range covers cold-boot and warm-tablet conditions without thermal derating, while the 28 C/W theta-JA from the 48-QFN thermal pad spreads heat into a copper plane.
Recommandé
Intel Y/U-Series Notebook Power
For Intel Y-series and U-series processors, the TPS51640RSLR implements SVID voltage identification, load-line, and adaptive thermal management required by Intel IMC firmware. Per-phase switching up to 1.5 MHz keeps the converter above the AM-band, reducing audible noise and easing filter design. Programmable soft-start prevents inrush at 0.5%-accuracy cold-boot scenarios. This positions the controller as a turnkey solution for 9-15 W TDP notepads and slim notebooks.
Recommandé
Industrial IMVP7-Compatible Embedded Platform
Outside the mainstream laptop market, the TPS51640RSLR is used in industrial IMVP7-derived SBCs and panel PCs that need multi-phase SVID control. The wide 4.5V-28V input range accepts 12V/24V industrial rails through a preregulator, and the 0.5% Vout accuracy supports AI vision, embedded GPU and edge inferencing workloads. Protections (OVP/UVP/OCP/Thermal Shutdown) reduce BOM by replacing several discrete supervisor devices.
Recommandé
Server Memory/Voltage-Positioned Auxiliary Rail
Although designed for IMVP7 CPUs, designers have adapted the TPS51640RSLR for voltage-positioned memory rails where 0.5% accuracy and D-CAP+ dynamic performance are valuable. The two rails (3-phase + 1-phase) provide enough flexibility to drive DDR terminators or auxiliary cores, and the 1.0V internal reference enables sub-1V output. This is a derivative, non-IMVP7 use case - firmware must bypass SVID to a fixed VID command set.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TPS51640RSLR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TPS51640ARSLR | TPS59640RSLR | TPS59641RSLR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-QFN (RSL) 7x7 mm | 48-QFN (RSL) 7x7 mm - same | 48-QFN (RSL) 7x7 mm - same | 48-QFN (RSL) 7x7 mm - same |
| Topology | 2+1 phase (CPU 3-phase + GPU 1-phase) | 2+1 phase | 2+1 phase | 2+1 phase |
| IMVP Compliance | IMVP7 | IMVP7 | IMVP6.5 | IMVP6.5 |
| V_BOOT Voltage | 1.1 V | 0 V | 0 V | 1.1 V |
| Output Voltage Accuracy | 0.5% | 0.5% | 0.5% | 0.5% |
| Switching Frequency Range | 250 kHz to 1.5 MHz | 250 kHz to 1.5 MHz | 250 kHz to 1.5 MHz | 250 kHz to 1.5 MHz |
| Operating Temperature | -10 C to +105 C | -10 C to +105 C | -40 C to +105 C | -40 C to +105 C |
Principaux différenciateurs
- Original V_BOOT = 1.1V for legacy CPU platforms (vs TPS51640ARSLR)
- Wider operating temperature floor than IMVP6.5 series (vs TPS59640RSLR)
- IMVP7 SVID command set vs older IMVP6.5 (vs TPS59640RSLR / TPS59641RSLR)
Notes de conception
Estimated: at full 3-phase CPU load of ~80A with Vout=0.8V and Vin=12V, total dissipation across external high-/low-side MOSFETs and the controller can reach 6W. The 48-pin QFN (RSL) has a typical theta_JA near 28 C/W on a 4-layer 2-oz copper PCB; assume junction-to-ambient rise near 170C at 6W. Use at least 1 square inch of copper array under the thermal pad plus thermal vias to inner planes to keep Tj below 105C.
Route the SVID bus lines (SVID_DATA, SVID_CLK, SVID_ALERT) as a 50 ohm microstrip on inner layers or guarded by GND to avoid jitter on the ~26 MHz clock. Place the per-phase bootstrap capacitor (BOOTx-PGND) within 5 mm of the IC. The current-sense traces (CS1N, CS1P, CS2N, CS2P, CS3N, CS3P, CSP, CSN) must be kelvin-connected to the low-side FET pads to preserve D-CAP+ accuracy.
Do not skip the REF 1.0V bypass capacitor (1 uF X7R minimum) - it sets the DAC reference for all VID commands. Ensure VR_RDY is correctly pulled up to PCH's 3.3V rail, otherwise the CPU will not release POST and the platform will fail to boot. Never tie ILIM to VCC; an external resistor divider to AGND must set the per-phase current limit. The SVID address is hard-coded - if two controllers share a bus, SVID_ALERT collisions will occur.
Informations de conformité
RoHS compliant per TI product page; not AEC-Q100 qualified - no automotive-grade equivalent exists in this family.
