מוצרים (44,000+)

PCF8575DB - 16-Bit I2C I/O Expander | Texas Instruments
PCF8575DB

PCF8575DB - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCF8575DB is a 16-bit remote I/O expander for I2C and SMBus systems, operating from 2.5 V to 5.5 V with bus speeds up to 400 kHz in a 24-pin SSOP package. Its two 8-bit quasi-bidirectional ports, P07–P00 and P17–P10, can be individually configured as inputs or outputs without a separate data-direction register. The device also includes an open-drain interrupt output and three hardware address inputs, allowing as many as eight devices to share an I2C bus. An I/O expander is an interface IC that extends the number of digital input and output lines available to a microcontroller or other host processor. The PCF8575 belongs to the I2C interface IC hierarchy and uses a serial command-and-data bus to transfer port state over two wires. Its 16 quasi-bidirectional lines can reduce the number of GPIO pins required by a host while remaining suitable for common logic-level inputs, relay-control signals, status indicators, and LED loads. Each quasi-bidirectional I/O has latched output capability and high-current drive for directly driving LEDs. The same line can be read as an input without changing the output latch, although the electrical behavior differs from a conventional push-pull output. At power-on, all I/O ports are high. The three address pins provide hardware-selectable device addresses for a maximum of eight PCF8575 devices on one bus, while the open-drain interrupt output provides a hardware indication of input-port state changes. The interface supports both I2C and SMBus operation, and the verified product information identifies operation up to 400 kHz. Low standby-current consumption is specified at a maximum of 10 µA. These characteristics make the device useful in embedded systems where bus wiring, connector pin count, standby power, or host GPIO availability constrain the design. The 24-pin SSOP, identified by distributor records as SSOP-24 with a 5.30 mm width and 0.209 inch lead spacing, supports compact surface-mount assembly. Typical uses include reading switches and keypads, driving LED indicators, monitoring digital control signals, controlling discrete transistors or relays, and expanding I/O in industrial controllers, appliance controllers, test equipment, and microcontroller boards. Because the interrupt output is open-drain, multiple interrupt-capable devices can share a common signal when the system supports wired-AND behavior. Firmware must also account for the I2C address, port polarity, and quasi-bidirectional input current requirements. The primary design consideration is choosing the pull-up voltage and ensuring that the bus capacitance and wiring permit reliable operation at 400 kHz. I2C pull-up resistors should be placed on the host side of long or branched wiring, and software should acknowledge only the interrupt source determined by the device address. The available verified material does not provide a complete pin table, explicit price values, or detailed absolute-maximum ratings. This product page consolidates the verified manufacturer description, distributor package identification, I2C features, interrupt behavior, power-on state, and available substitute references. It also adds application guidance, engineering caveats, and a transparent distinction between verified specifications and parameters that still require confirmation from the complete manufacturer datasheet.

RFQ צור קשר
PCF8575DBR - 16-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)
PCF8575DBR

PCF8575DBR - 16-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)

Texas Instruments PCF8575DBR is a 16-bit remote I/O expander for I2C and SMBus systems, operating from 2.5 V to 5.5 V with bus speeds up to 400 kHz in a 24-pin SSOP package. Its two 8-bit quasi-bidirectional ports, P07–P00 and P17–P10, can be individually configured as inputs or outputs without a separate data-direction register. The device also includes an open-drain interrupt output and three hardware address inputs, allowing as many as eight devices to share an I2C bus. An I/O expander is an interface IC that extends the number of digital input and output lines available to a microcontroller or other host processor. The PCF8575 belongs to the I2C interface IC hierarchy and uses a serial command-and-data bus to transfer port state over two wires. Its 16 quasi-bidirectional lines can reduce the number of GPIO pins required by a host while remaining suitable for common logic-level inputs, relay-control signals, status indicators, and LED loads. Each quasi-bidirectional I/O has latched output capability and high-current drive for directly driving LEDs. The same line can be read as an input without changing the output latch, although the electrical behavior differs from a conventional push-pull output. At power-on, all I/O ports are high. The three address pins provide hardware-selectable device addresses for a maximum of eight PCF8575 devices on one bus, while the open-drain interrupt output provides a hardware indication of input-port state changes. The interface supports both I2C and SMBus operation, and the verified product information identifies operation up to 400 kHz. Low standby-current consumption is specified at a maximum of 10 µA. These characteristics make the device useful in embedded systems where bus wiring, connector pin count, standby power, or host GPIO availability constrain the design. The 24-pin SSOP, identified by distributor records as SSOP-24 with a 5.30 mm width and 0.209 inch lead spacing, supports compact surface-mount assembly. Typical uses include reading switches and keypads, driving LED indicators, monitoring digital control signals, controlling discrete transistors or relays, and expanding I/O in industrial controllers, appliance controllers, test equipment, and microcontroller boards. Because the interrupt output is open-drain, multiple interrupt-capable devices can share a common signal when the system supports wired-AND behavior. Firmware must also account for the I2C address, port polarity, and quasi-bidirectional input current requirements. The primary design consideration is choosing the pull-up voltage and ensuring that the bus capacitance and wiring permit reliable operation at 400 kHz. I2C pull-up resistors should be placed on the host side of long or branched wiring, and software should acknowledge only the interrupt source determined by the device address. The available verified material does not provide a complete pin table, explicit price values, or detailed absolute-maximum ratings. This product page consolidates the verified manufacturer description, distributor package identification, I2C features, interrupt behavior, power-on state, and available substitute references. It also adds application guidance, engineering caveats, and a transparent distinction between verified specifications and parameters that still require confirmation from the complete manufacturer datasheet.

RFQ צור קשר
PCF8575DW - 16-Bit I2C I/O Expander | Texas Instruments
PCF8575DW

PCF8575DW - 16-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8575DW is a 16-bit I2C/SMBus remote I/O expander with interrupt output, designed for 2.5 V to 5.5 V operation and packaged in a 24-pin SOIC. It provides 16 general-purpose digital I/O lines through a two-wire serial interface, making it useful for expanding microcontroller pin availability in embedded control systems. The device supports a 400 kHz fast I2C bus and includes three hardware address pins for addressing up to eight devices on the same bus. An I/O expander is an interface IC that translates serial bus commands into parallel digital input or output lines. The PCF8575 belongs to the I2C I/O expander category, within interface ICs and broader semiconductor power and signal-conditioning systems. Its design allows a host microcontroller to control or monitor multiple discrete digital signals while conserving the limited I/O pins available on small microcontrollers. Key features include 16 I/O lines, an operating supply range of 2.5 V to 5.5 V, a maximum I2C clock frequency of 400 kHz, low standby-current consumption of 10 uA maximum, and an open-drain interrupt output. The outputs are latched and can provide high-current drive capability for directly driving LEDs. A current source connected to VCC also allows outputs to be actively driven high for systems that require an active-high output state. The PCF8575DW communicates through SCL and SDA, with three address pins selecting one of eight possible bus addresses. The interrupt output provides a hardware indication that an input state has changed, allowing the host controller to respond without continuously polling the expander. The 400 kHz bus rate supports efficient transfers between the controller and the expanded I/O bank, while the 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V systems. Typical applications include industrial control panels, keypad and button interfaces, LED status indicators, relay or transistor control, sensor and switch monitoring, and general-purpose embedded system I/O expansion. The PCF8575DW is particularly suitable when a controller has insufficient GPIO pins for external switches, indicators, or actuators. Its interrupt output can reduce host processing time when multiple remote inputs require attention. When designing around the PCF8575DW, confirm the controller's I2C voltage, pull-up resistor arrangement, address selection, and the electrical requirements of every connected load. The open-drain interrupt output requires appropriate pull-up treatment, and LED or relay loads must remain within the device's stated drive and current limits. The 24-pin SOIC footprint is intended for surface-mount PCB assembly. This product page combines the verified manufacturer and distributor descriptions, packaging information, source links, and engineering-oriented design guidance for engineers evaluating the PCF8575DW. It distinguishes verified facts from unavailable detailed specifications and provides practical context for choosing a 16-bit I2C/SMBus I/O expander in embedded control designs.

RFQ צור קשר
PCF8575DWR - 16-Bit I2C I/O Expander | Texas Instruments
PCF8575DWR

PCF8575DWR - 16-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8575DWR is a 16-bit I2C and SMBus I/O expander with interrupt, operating from 2.5 V to 5.5 V in a 24-pin SOIC (DW) package. It adds 16 latched quasi-bidirectional I/O lines to a host microcontroller through a two-wire serial bus, supports operation up to 400 kHz, and provides three hardware address pins for connecting up to eight devices on one bus. The device also includes an open-drain interrupt output for change notification. An I/O expander is an interface IC that converts serial commands from a microcontroller into parallel input or output signals. In the product hierarchy, the PCF8575 belongs to the I2C GPIO expander class, within interface ICs and broader digital semiconductor systems. It is useful when a controller needs more GPIO pins than are available directly, avoiding a redesign or the addition of a larger microcontroller package. Key features include 16 independently latched I/O ports, a 2.5 V to 5.5 V supply range, 400 kHz fast I2C operation, and low standby-current consumption of 10 uA maximum. Three hardware address pins provide eight selectable bus addresses. The outputs can latch data for direct LED drive and include a current source to VCC for actively driving a high. An open-drain interrupt output allows a controller to react to selected input changes without continuously polling the device. The PCF8575 implements a simple register-based interface in which the 16 ports are used for data transfer, configuration, and output control. Its quasi-bidirectional I/O structure suits many microcontroller systems, although each pin is intended primarily for ordinary digital loads rather than unrestricted capacitive or high-current loads. Power and signal behavior remain compatible with the 2.5 V to 5.5 V operating range stated by Texas Instruments. Typical applications include industrial control modules, keypad and switch interfaces, LED status panels, relay or solenoid driver boards, building-automation equipment, and small embedded control systems. The device is particularly useful when a host controller needs 16 additional lines while retaining a compact 24-pin SOIC footprint and a two-wire connection to the main PCB. Designers should account for the quasi-bidirectional output architecture, use appropriate pull-up arrangements for open-drain interrupt signaling, and confirm that connected loads remain within the device's output-drive limits. I2C pull-up resistance and bus capacitance should be selected for the full system, including cable length, bus speed, and the number of devices. This page combines manufacturer specifications, distributor availability, package details, practical application guidance, and same-footprint replacement analysis to support faster component selection and PCB-level decision-making.

RFQ צור קשר
PCF8575PW - 16-Bit I2C I/O Expander | Texas Instruments
PCF8575PW

PCF8575PW - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCF8575PW is a 16-bit I2C/SMBus I/O expander with interrupt output, operating from 2.5 V to 5.5 V and supporting bus speeds up to 400 kHz. The device is packaged in a 24-pin TSSOP (PW) package and provides three hardware address inputs for operating as many as eight devices on one bus. An I/O expander is an interface IC that converts a serial two-wire bus into additional parallel input and output lines. In the product hierarchy, the PCF8575 belongs to the I/O expander class, interface ICs, and integrated circuits. It allows a microcontroller with limited GPIO pins to control or monitor additional external signals without requiring a large number of direct host-controller pins. Key features include 16 individually controlled I/O lines, an open-drain interrupt output, and a maximum standby-current consumption of 10 µA. The three address pins allow up to eight PCF8575 devices to share an I2C bus. Outputs are latched and have high-current drive capability for directly driving LEDs, while a current source to VCC supports actively driving a high output state. The PCF8575 interface uses SCL and SDA for serial communication and provides an open-drain interrupt for signaling the host controller. Its 400 kHz fast-I2C capability suits embedded control systems operating at moderate bus rates. The device is compatible with most microcontrollers, making it useful where firmware and board space make another dedicated parallel interface impractical. Typical uses include LED panels, key scanners, relay or switch controls, sensor and switch inputs, and general-purpose remote I/O in industrial, consumer, communications, and embedded systems. Each of the 16 I/O ports can be configured as an input or output through the serial interface, while the interrupt output can reduce unnecessary host-controller polling. Designers should account for the open-drain nature of the interrupt and I2C bus, provide suitable pull-up resistors, confirm address configuration, and review the datasheet for power-on output states and current limits. External drivers may be required when a load exceeds the device's specified drive capability. This page consolidates verified manufacturer and distributor information, documents where detailed ratings are unavailable, and distinguishes true package-compatible alternatives from look-alike expanders whose register behavior differs. It also provides application-specific engineering guidance that helps engineers evaluate the PCF8575PW before committing it to an existing PCB.

RFQ צור קשר
PCF8575PWE4 - 16-Bit I2C/SMBus I/O Expander by TI
PCF8575PWE4

PCF8575PWE4 - 16-Bit I2C/SMBus I/O Expander by TI

Texas Instruments PCF8575PWE4 is a 16-bit I2C/SMBus remote I/O expander with interrupt output, operating from 2.5 V to 5.5 V and supporting I2C bus speeds up to 400 kHz. The device provides 16 general-purpose quasi-bidirectional I/O lines through two 8-bit ports and is packaged in a 24-pin TSSOP format with a 0.65 mm terminal pitch. An I/O expander is an interface IC that increases the number of digital input and output lines available to a host microcontroller or other bus controller. The PCF8575 connects through the two-wire I2C or SMBus interface, while its parallel port provides individual control and status signals for attached peripherals. In the product hierarchy, it is an I/O expander, bus interface IC, and semiconductor designed for embedded control and general-purpose remote I/O. The principal features include 16 individually addressable I/O lines, two parallel ports, a 2.5 V to 5.5 V operating supply range, and an open-drain interrupt output. The I2C interface operates up to 400 kHz, and the device has maximum standby-current consumption of 10 uA. Address selection by hardware pins allows multiple expanders to coexist on one bus without using a large number of host I/O pins. Communication with the PCF8575 uses serial clock and serial data lines, while power-down, reset, port 0, port 1, and interrupt functions occupy dedicated pins. Quasi-bidirectional ports can source output current, accept logic inputs, and participate in partial high-impedance operation. The open-drain interrupt output provides a common hardware indication that one or more port inputs have changed, allowing the host to service the device without continuously polling every line. Typical uses include industrial control panels, sensor and actuator interfaces, programmable instrument front panels, embedded data-acquisition systems, and compact control boards that need more digital lines than the host controller provides. The 2.5 V minimum supply supports low-voltage embedded systems, while the 5.5 V maximum allows operation from a conventional 5 V rail. The 24-pin TSSOP package also fits densely populated PCB layouts with 0.65 mm lead spacing. Design the bus pull-up network for the selected SCL and SCL frequency and system capacitance, and account for the voltage drop contributed by pull-up resistance when more than one expander drives the bus low. Confirm that every connected node is 5 V tolerant before using the 5.5 V maximum supply. Preserve the interrupt output's open-drain behavior and provide suitable pull-up or signal-conditioning arrangements where required. This page organizes the key electrical characteristics, complete package information, direct replacement options, and practical bus-layout guidance for engineers evaluating the PCF8575PWE4. It also provides focused comparisons for determining whether an alternative offers a meaningful functional or lifecycle advantage without requiring a PCB footprint change.

RFQ צור קשר
PCF8575PWG4 - 16-Bit I2C I/O Expander | Texas Instruments
PCF8575PWG4

PCF8575PWG4 - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCF8575PWG4 is a 16-bit I2C and SMBus I/O expander with an interrupt output, operating from 2.5 V to 5.5 V and supporting I2C speeds up to 400 kHz. The device provides 16 quasi-bidirectional I/O lines in a 24-pin TSSOP package, allowing a host microcontroller to monitor inputs and control outputs over a two-wire serial bus. Its open-drain interrupt output supports efficient change notification without continuous polling. An I/O expander is an interface IC that increases the number of general-purpose digital lines available to a microcontroller or other bus master. The PCF8575 belongs to the I/O expander category within interface ICs and translates parallel I/O operations into I2C or SMBus transactions. Its 16 ports can each operate as an input or output, with no separate data-direction register required. Key features include three hardware address inputs, eight programmable I/O ports on each side of the device, and power-on initialization with all I/O lines high. The quasi-bidirectional architecture uses a weak pull-up arrangement that allows an external circuit to override an output-low state. The open-drain interrupt output can be wired as active-low and provides a shared indication when an input changes state. The PCF8575 core supports operation across a 2.5 V to 5.5 V supply range, making it suitable for both 3.3 V and 5 V systems. Its I2C interface operates up to 400 kHz, while the three address pins permit multiple expanders to share a bus. Because each port combines input detection and output drive, the device is particularly useful for reading switch states, reading logic-level sensors, controlling discrete loads, and driving LED indicators within defined current limits. Typical applications include industrial control boards, automated test equipment, display and keypad interfaces, LED status panels, and small embedded systems where a microcontroller has insufficient port pins. The open-drain interrupt output is especially useful in battery-operated or duty-cycled systems because the host can remain idle until an input event requires attention. The interrupt pin remains open-drain, allowing multiple expanders to share a common interrupt line when the system uses separate address selections. For PCB design, place the device close to the connector or sensor wiring that it serves and route the SCL and SDA traces away from high-current switching nodes. Pull-ups must be sized for the bus voltage and capacitance, while the interrupt net requires appropriate pull-up treatment because its output is open-drain. Confirm every external driver against the port sink-current and voltage limits in the manufacturer datasheet. This page combines the manufacturer electrical characteristics, package information, drop-in device comparison, interface design guidance, and application-specific implementation guidance for engineers designing around the PCF8575PWG4.

RFQ צור קשר
PCF8575PWR - 16-Bit I2C I/O Expander | Texas Instruments
PCF8575PWR

PCF8575PWR - 16-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8575PWR is a 16-bit I2C/SMBus I/O expander with an interrupt output, a 2.5 V to 5.5 V operating range, and a 400 kHz bus rate. The device is packaged in a 24-pin TSSOP and adds 16 quasi-bidirectional I/O lines to a host controller over a two-wire serial interface. An I/O expander is an interface IC that extends the number of digital input and output pins available to a microcontroller or other embedded controller. The PCF8575 sits between the host processor and external peripherals, using I2C or SMBus for command and data transfer while presenting a parallel port to connected circuitry. Its two independent eight-bit ports support both input and output operation without separate data-direction registers. The PCF8575PWR provides 16 quasi-bidirectional I/O lines, with each line usable as an input or output. Its latched outputs have high-current drive capability for directly driving LEDs. Three hardware address pins allow up to eight devices to share the same I2C bus, while the open-drain interrupt output provides a hardware indication of input-port activity. The interface supports operation up to 400 kHz, and standby current consumption is specified at no more than 10 microamperes. All I/O pins are high at power-on, which provides a defined reset state for the output latch. The quasi-bidirectional architecture includes a weak current source toward VCC, so engineers should account for this behavior when designing inputs, pull-ups, and output transitions. Typical uses include expanding a limited microcontroller pin count for LEDs, switches, keypads, sensors, relay-control logic, and simple digital display interfaces. Because the device communicates over I2C or SMBus, it is particularly useful when a design needs many slow-changing digital lines but cannot allocate a dedicated parallel port on the host controller. A key design consideration is the difference between quasi-bidirectional inputs and conventional push-pull outputs. Pull-up requirements, leakage currents, and the desired high or low state must be evaluated for every connected signal. Designers should also confirm address selection, interrupt handling, and supply levels before assigning functions to the two eight-bit ports. This product page organizes the manufacturer specifications, pin assignments, application guidance, and same-footprint alternatives into an engineering-focused reference. It also distinguishes direct pin-compatible choices from related expanders whose input or reset behavior differs, helping simplify design validation without obscuring the trade-offs that matter on the PCB.

RFQ צור קשר
PCF8584P - 90 kHz Multi-Master I2C Controller | NXP
PCF8584P

PCF8584P - 90 kHz Multi-Master I2C Controller | NXP

NXP Semiconductors PCF8584P is a multi-master I2C bus controller designed to transfer data at up to 90 kHz while supporting dual addressing modes and full arbitration. The device is packaged in a 20-pin PDIP and operates from a 4.5 V to 5.5 V supply, making it suitable for legacy parallel-interface industrial equipment that must connect to an I2C bus. An I2C bus controller is an interface IC that mediates communication between a host using a parallel or general-purpose processor interface and devices connected to the two-wire I2C bus. It sits within the broader interface-controller hierarchy: I2C controller, bus interface IC, interface bridge, and semiconductor. This positioning allows older parallel systems to exchange commands and data with sensors, memory devices, converters, and other I2C peripherals without redesigning the host bus architecture. The PCF8584P provides multi-master operation, dual addressing modes, and full arbitration. These features support shared-bus designs in which more than one potential controller may initiate communication. The 90 kHz maximum transfer rate is appropriate for moderate-speed control and data-exchange functions rather than high-bandwidth storage or display workloads. Its 4.5 V to 5.5 V operating range supports conventional 5 V industrial logic systems. The 20-pin PDIP package provides through-hole mounting, making PCF8584P well suited to legacy controller boards, industrial control equipment, test systems, and products where field replacement or retrofit is important. A parallel-to-I2C controller role allows the host processor to communicate through a parallel interface while the PCF8584P manages serial bus transactions. Dual addressing modes provide flexibility when integrating peripherals that use different address conventions or command structures. Typical applications include industrial instrumentation, programmable logic controllers, legacy data-acquisition equipment, embedded control modules, and factory automation systems. The device can also bridge a parallel host processor to sensors, EEPROMs, ADC or DAC devices, and other I2C components. System designers should account for the 90 kHz bus limit and use appropriate pull-up resistors and bus capacitance when laying out the I2C network. The principal design consideration is compatibility with the existing host interface and 20-pin through-hole footprint. Confirm signal levels, addressing, arbitration behavior, and timing against the manufacturer datasheet before replacing an existing component. Because this is a mature parallel-to-I2C architecture, it is most valuable when maintaining legacy equipment rather than implementing a new compact embedded bus interface. This page combines the manufacturer specification, package information, interface characteristics, sourcing guidance, and engineering-oriented application analysis to help designers evaluate the PCF8584P for legacy I2C expansion and industrial retrofit work.

RFQ צור קשר
PCF8591P - 8-Bit I2C ADC/DAC, 4 Inputs | NXP Semiconductors
PCF8591P

PCF8591P - 8-Bit I2C ADC/DAC, 4 Inputs | NXP Semiconductors

NXP Semiconductors PCF8591P is a single-chip, single-supply, low-power 8-bit CMOS data-acquisition device with four analog inputs, one analog output, and a serial I2C-bus interface. It accepts supply voltages from 2.5 V to 6 V and is packaged in a 16-pin DIP, making it suitable for compact analog signal acquisition and output-control systems that use an embedded serial bus. An ADC/DAC is a data-conversion semiconductor that bridges analog and digital circuitry. The ADC portion converts an analog voltage into a digital value, while the DAC portion converts a digital value into an analog output voltage. A combined ADC/DAC can therefore place sensing, measurement, and analog output generation on one I2C-connected chip. The PCF8591 belongs to the broader data-converter, interface-IC, and power-management-system hierarchy used in embedded equipment. The principal features are 8-bit conversion resolution, four analog input channels, one analog output channel, and a serial I2C-bus interface. Three hardware-address pins labeled A0, A1, and A2 allow the device address to be programmed, permitting as many as eight devices to share an I2C bus without requiring additional address-decoding hardware. Its single-supply operation and low-power CMOS construction simplify integration in systems that do not need bipolar input or output signals. Control, address, and converted data are transferred through the I2C interface, reducing the number of parallel signal lines required between the converter and a host microcontroller. The four-input architecture suits multiplexed measurement systems, while the single DAC output provides a simple level for exercising analog control inputs. The 16-DIP package is straightforward to prototype and install through-hole assembly on educational, industrial-control, and legacy embedded boards. Typical uses include monitoring resistive sensors, reading potentiometer positions, measuring slowly varying analog voltages, generating an analog control level, and building low-cost data-logging or process-control interfaces. The device is particularly useful when a system already communicates through I2C and needs both conversion directions without allocating a separate ADC and DAC. Because the converter is 8-bit, its useful measurement resolution and output granularity are inherently limited compared with higher-resolution data converters. During schematic design, verify analog input range, output loading, reference behavior, address selection, and logic levels against the manufacturer datasheet before committing a board. Keep analog and digital return currents separated where practical, provide a low-noise supply path, and avoid long sensitive analog traces beside the I2C clock and data lines. Confirm that the host firmware supports the device address selected by A0, A1, and A2. This product page consolidates the verified device description, datasheet access, package details, application guidance, and replacement-selection considerations. It also distinguishes verified drop-in options from broader functional equivalents so engineers can assess PCB compatibility, bus behavior, and conversion requirements before approving a substitute.

RFQ צור קשר
PCF8591T - 8-bit I2C ADC/DAC, 4-Ch Input | NXP Semiconductors
PCF8591T

PCF8591T - 8-bit I2C ADC/DAC, 4-Ch Input | NXP Semiconductors

The NXP PCF8591T is a single-chip, single-supply, low-power 8-bit CMOS data acquisition device that integrates four analog inputs, one analog output, and a serial I2C-bus interface in a 16-pin SO (SOT162-1) surface-mount package. The PCF8591T combines an 8-bit successive-approximation A/D converter and a single 8-bit D/A converter on the same die, allowing a single I2C addressable device to handle both digitizing external analog signals and reconstructing an analog voltage for control or waveform output. The maximum I2C-bus clock operates up to 11.1 kHz symbol rate per the DigiKey listing. What is an 8-bit data acquisition IC? A data acquisition (DAQ) IC is a mixed-signal integrated circuit that bridges the analog and digital domains, typically containing one or more analog-to-digital converters (ADCs) and sometimes digital-to-analog converters (DACs) along with a digital interface for a host microcontroller. Within the broader taxonomy, the PCF8591T is an 8-bit successive-approximation ADC with an 8-bit DAC, controlled via an I2C serial interface - falling into the category of low-speed, low-resolution, system-management data converters used for sensor reading, setpoint generation, and analog control loops in embedded designs. Key features of the PCF8591T include four multiplexed single-ended analog inputs (or three differential inputs selectable via the control byte), one rail-to-rail analog output, three hardware address pins (A0-A2) allowing up to eight devices on the same I2C bus without glue logic, and a single 2.5V to 6V supply. The on-chip track-and-hold and successive-approximation ADC delivers 8-bit resolution at typical conversion rates suitable for sensor monitoring and process control. The DAC section can be configured for 4-quadrant multiplication when an external reference is supplied, enabling digitally controlled gain and offset in signal-conditioning paths. Typical applications include battery monitoring, industrial process-variable sensing (temperature, pressure, flow), LED brightness and contrast control via the DAC, closed-loop analog control in HVAC and appliance designs, and hobbyist/educational platforms (Raspberry Pi and Arduino sensor shields). The wide supply range (2.5V-6V) and low standby current also suit portable instrumentation and remote sensor nodes. When designing with the PCF8591T, ensure the I2C pull-ups are sized for the bus capacitance and clock speed, place a 0.1uF decoupling capacitor close to VDD, and respect the address-pin strapping (A0-A2) so multiple devices coexist on the same bus. The analog inputs are not 5V-tolerant above VDD; use a resistive divider or op-amp buffer when sensing higher voltages.

RFQ צור קשר
PCF8593P - Low-Power I2C Clock/Calendar | NXP
PCF8593P

PCF8593P - Low-Power I2C Clock/Calendar | NXP

NXP PCF8593P is a low-power CMOS clock and calendar integrated circuit with a 32.768 kHz oscillator, 1 V to 6 V supply range, and an I2C serial interface, housed in an 8-pin DIP package. The device combines timekeeping, calendar, and RAM functions for compact embedded systems that need an energy-efficient real-time clock without a separate microcontroller timekeeping routine. A real-time clock, or RTC, is a specialized semiconductor that maintains time and calendar information independently of the main processor. The RTC hierarchy includes clock and calendar ICs, timekeeping integrated circuits, and broader power-management or timing devices. The PCF8593P uses a two-wire bidirectional I2C bus to transfer addresses and data efficiently while its internal 32.768 kHz oscillator provides the timebase for seconds, minutes, hours, and calendar functions. The PCF8593P integrates a built-in word-address register that increments automatically after each written or read data byte. Its first eight RAM bytes support the clock and calendar functions, while additional RAM is available for general-purpose storage. This combination allows a host microcontroller to read and update time information through a compact serial interface without continuously counting timer interrupts or maintaining a software calendar. Its 1 V to 6 V operating supply range allows use with low-voltage embedded systems, while the CMOS construction and low-power optimization suit battery-powered equipment. The I2C interface reduces wiring requirements compared with parallel calendar devices and permits addressable access to registers and RAM. The manufacturer datasheet should be consulted for electrical limits, oscillator accuracy, current consumption, and operating-temperature limits before final design release. Typical applications include industrial data loggers, embedded instrumentation, consumer appliances, metering equipment, and compact control systems that require date and time records. It is particularly useful when the main controller can remain powered down between data-capture events or when event chronology must survive a system reset. An RTC also helps prevent clocks from drifting when the application is disconnected from a network time source. Design the I2C pull-up resistors and supply bypassing for the operating environment, and preserve the recommended oscillator and layout requirements from the manufacturer datasheet. Verify address allocation when multiple I2C devices share the bus. Account for oscillator accuracy when defining measurement intervals and avoid presenting the RTC as a precision chronometer when its specified accuracy does not meet that requirement. This product page combines the manufacturer function description with practical interface, package, sourcing, and replacement guidance. It also highlights the distinction between a true pin-compatible clock/calendar substitution and a merely similar real-time-clock device, helping designers preserve the original 8-DIP footprint and I2C implementation.

RFQ צור קשר
PCF8593T/1,118 - I2C RTC Clock/Calendar, 8-SOIC | NXP Semiconductors
PCF8593T/1,118

PCF8593T/1,118 - I2C RTC Clock/Calendar, 8-SOIC | NXP Semiconductors

The NXP Semiconductors PCF8593T/1,118 is a CMOS Real-Time Clock (RTC) and calendar circuit optimized for low power consumption, housed in an 8-pin SOIC (SOT96-1) package. The device provides an 8-bit serial interface over the industry-standard I2C (2-wire) bus, supports a supply voltage range of 2.5 V to 6.0 V, and integrates a 32.768 kHz oscillator circuit that drives timekeeping, calendar, and counter functions in the first 8 bytes of internal RAM. A Real-Time Clock (RTC) is a dedicated integrated circuit that keeps track of current time and date (typically seconds, minutes, hours, days, weekdays, months, years) even when the main system power is removed, usually backed by a small battery or supercapacitor. Within the broader component taxonomy, an RTC sits under the clock & timing category, which itself is a subset of integrated circuits. RTCs are essential building blocks for any embedded design that needs time-of-day awareness: from data loggers and metering equipment to industrial controllers and consumer appliances. The PCF8593 represents the classic low-power serial-RTC architecture that has dominated I2C-based designs since the 1990s. Key features of the PCF8593T/1,118 include 240 bytes of general-purpose static RAM available beyond the timekeeping registers, a programmable 32.768 kHz oscillator with on-chip load capacitors, automatic word-address increment after each read/write byte, a 24-hour or 12-hour format option, and low standby current in the microamp range. The 8-SOIC package is industry standard (3.90 mm body width), making the device drop-in compatible with the classic 8-pin DIP footprint pad layout when designed with the SOIC land pattern. The internal address counter eliminates the need for burst-mode addressing in firmware, simplifying I2C driver code. Typical applications include battery-backed wall-clock modules for appliances, time-of-day stamping in metering and data-acquisition systems, low-power sensor nodes that wake periodically and need an accurate timestamp, industrial programmable logic controllers (PLCs) that log events, and consumer electronics such as VCRs, set-top boxes, and audio gear that must retain clock time across power cycles. When designing with this part, place the 32.768 kHz watch crystal as close as possible to the OSCO/OSCI pins to minimize parasitic capacitance, ensure the I2C pull-up resistors are sized correctly for the bus capacitance, and keep the backup battery path well-decoupled to survive brown-outs. The part is approaching end-of-life per the NXP product page, so designers should evaluate the PCF85263A or PCF8563 as pin-compatible modern replacements for new designs.

RFQ צור קשר
PCI4451GJG - Integrated PC Card & 1394 OHCI Controller | TI
PCI4451GJG

PCI4451GJG - Integrated PC Card & 1394 OHCI Controller | TI

The Texas Instruments PCI4451GJG is an integrated PC Card controller and 1394 (FireWire) OHCI controller that combines dual-slot CardBus (PCMCIA) support with a single 400 Mbps IEEE 1394a link in a single PCI device. It supports two independent PC Card slots compliant with the 1997 PC Card Standard, provides a 32-bit CardBus bridge for both slots, and integrates a 3.3 V physical layer for IEEE 1394 with one fully compliant cable port at 100/200/400 Mbps. The device is offered in a 257-ball MicroStar BGA (GJG) package, 16x16 mm, designed for space-constrained add-in cards and embedded platforms. Key features include PCI 2.2 host-side compliance, integrated 1394 OHCI 1.1 controller with cable power management, support for Zoom Video (ZV) port, ACPI 1.0 compliant power management with D0/D1/D2/D3 states and PME#, and programmable CardBus signal voltage (3.3 V / 5 V / VPP). The integrated PHY removes the need for an external 1394 link-layer chip, reducing both BOM count and PCB area versus two-chip implementations. Technically, the PCI4451 uses a single 33 MHz, 32-bit PCI bus to bridge the host CPU to two PC Card sockets and one 1394 port. Internal DMA engines handle PC Card data movement with scatter-gather support, while a dedicated 1394 PHY implements bus-reset, arbitration, and cable-not-active detection per IEEE 1394a-2000. CardBus card insertion/removal is managed by per-socket card detect and voltage sense pins that feed the integrated socket controller. Typical applications include legacy industrial PCs, test and measurement chassis with PC Card (PCMCIA) data acquisition modules, docking stations, embedded military/aerospace single-board computers, and add-in Combo cards (CardBus + 1394a) for legacy Windows XP / Windows 2000 platforms where both buses remain in active service for instrumentation capture. When designing, observe the 257-ball BGA escape pattern: route CardBus data, address and control signals on the outer two rows of balls and place the 1394 cable port traces near the package edge to minimize stub length. A 27 MHz crystal with the on-chip PLL provides the 1394 PHY clock; follow TI's reference layout for the PHY section to remain IEEE 1394a compliant. This page synthesizes distributor pricing, exact-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PCM1600Y - 24-Bit 6-Channel 96kHz DAC | Texas Instruments
PCM1600Y

PCM1600Y - 24-Bit 6-Channel 96kHz DAC | Texas Instruments

The Texas Instruments PCM1600Y is a 24-bit, 6-channel, 96kHz-sampling enhanced multilevel delta-sigma digital-to-analog converter in a 48-pin LQFP package. It supports Standard, I2S, and left-justified audio data interfaces with user-selectable 16-, 18-, 20-, and 24-bit data lengths. According to the manufacturer datasheet, the device operates with +VCC = 5V and +VDD = 3.3V under the stated test conditions. Its 6-channel architecture makes it suitable for multichannel audio equipment, home-theater systems, digital mixing consoles, and automotive or industrial audio platforms that require multiple synchronized analog outputs. A delta-sigma DAC is a digital-to-analog converter category that uses noise shaping and digital filtering to convert PCM audio samples into continuous analog voltages. Within the broader hierarchy, PCM1600Y is an audio DAC, which is an ADC/DAC interface device and part of the broader semiconductor and signal-conversion product family. Its SoundPlus architecture combines 24-bit quantization with a 96kHz sampling capability, providing a direct conversion path for multichannel digital audio. Verified features include 24-bit resolution, six output channels, 96kHz sampling, user-selectable Standard, I2S, and left-justified formats, and selectable 16-, 18-, 20-, or 24-bit input words. The audio data uses MSB-first binary two's-complement formatting. Operating conditions include a +5V analog supply and a +3.3V digital supply in the cited datasheet test setup, enabling a practical separation between analog and digital supply domains. The PCM1600 family is positioned for applications where several audio channels must share a common digital source and clock. Common hardware arrangements route I2S or left-justified PCM data from a source such as a receiver, processor, or digital audio interface into the converter, then send six analog outputs through output filtering and coupling stages. The converter's 48-LQFP package provides 48 externally accessible connections for power, ground, clocks, data, control signals, and analog channels. Typical uses include surround-sound decoding, multichannel music playback, professional digital mixers, automotive audio head units, and industrial audio consoles. In each case, synchronized six-channel conversion reduces the need for multiple discrete DACs while retaining a standardized digital audio interface. The available 100kHz-class I2S listing and the 96kHz sampling description identify PCM1600Y as a high-resolution multichannel converter rather than a low-cost stereo codec. Designers should preserve the required analog and digital supply structure, provide clean references and clocking, and implement the manufacturer's recommended output-filter and bypass networks. Because the provided data does not expose the complete pin list, analog specifications, clock requirements, or recommended passive values, those details must be confirmed in the manufacturer datasheet before schematic release or PCB implementation. This product record combines verified distributor descriptions, the manufacturer-linked PCM1600 family datasheet, same-package alternatives, and practical selection guidance. It also distinguishes documented facts from unavailable parameters so engineers can identify what still requires circuit-level verification without relying on invented electrical values.

RFQ צור קשר
PCM1600Y/2K - 24-Bit 6-Ch 96kHz Audio DAC | Texas Instruments
PCM1600Y/2K

PCM1600Y/2K - 24-Bit 6-Ch 96kHz Audio DAC | Texas Instruments

Texas Instruments PCM1600Y/2K is a 24-bit, six-channel enhanced multilevel delta-sigma digital-to-analog converter for high-fidelity audio systems. It supports sampling rates up to 96 kHz and operates from dual 3.3 V analog and 5 V digital supplies. The converter is offered in a 48-pin LQFP package for surface-mount audio equipment. Its six output channels, user-selectable audio data formats, and 24-bit processing make it suitable for multichannel consumer audio, home theater, digital mixing, and multimedia systems. A digital-to-analog converter, or DAC, is an interface IC that converts digital audio samples into proportional analog voltages or currents. The DAC belongs to the signal-conversion hierarchy that includes codecs, audio interface ICs, data converters, and broader semiconductor devices. By generating the analog outputs required by amplifiers and speakers, a DAC bridges digital audio sources such as CDs, streamers, game consoles, and digital mixers with conventional analog amplification stages. The PCM1600Y/2K provides user-selectable Standard, I2S, and left-justified audio interfaces, along with selectable 16-, 18-, 20-, and 24-bit data lengths. It uses MSB-first, binary two's-complement data. These features allow the digital audio source and receiving system to share a common format. Six outputs support multichannel playback without requiring six separate converter packages, reducing board area and simplifying system synchronization. The enhanced multilevel delta-sigma architecture is intended for audio signal conversion with digital filtering and reconstruction. The datasheet characterization condition uses a 384fS system clock at 44.1 kHz and 24-bit data. The converter supports 96 kHz sampling, while its digital and analog sections use separate supply rails, helping isolate switching-related and digital-interface activity from the analog output stage. Exact dynamic-range, distortion, and channel-performance figures should be confirmed in the manufacturer datasheet for the selected operating mode. Typical uses include six-channel home-theater preamplifiers, surround-sound audio boards, active speakers, digital mixing consoles, and compact multimedia playback systems. In each case, the serial audio source connects to the PCM1600Y/2K, and the six analog outputs feed line-level amplifier stages. The device is also appropriate for custom digital audio appliances that need multiple synchronized outputs but do not require integrated headphone amplifiers or a complete audio codec. The PCB layout should preserve analog-signal integrity by separating digital input routing from the six analog outputs and placing the required bypass capacitors near their associated supply pins. A grounded, uninterrupted analog-output plane can reduce coupling, while careful component placement limits crosstalk between adjacent channels. Follow the manufacturer pin-description and typical-application tables when assigning tracks and selecting decoupling and filtering components. This product record combines the confirmed 24-bit, six-channel, 96 kHz functionality with package guidance, application fit, structured comparisons, and design-focused selection information. It is intended to help engineers evaluate DAC architecture, verify footprint requirements, and identify compatible same-family alternatives before beginning an audio-board design.

RFQ צור קשר
PCM1600YG4 - 24-Bit 6-Channel 96kHz DAC | Texas Instruments
PCM1600YG4

PCM1600YG4 - 24-Bit 6-Channel 96kHz DAC | Texas Instruments

The Texas Instruments PCM1600YG4 is a 24-bit, 6-channel digital-to-analog converter that supports audio sampling rates up to 96kHz. The device uses a serial data interface and separate analog and digital supply connections, making it suitable for multichannel consumer, communications, and industrial audio systems. It is housed in a 48-lead LQFP package with gull-wing leads. A DAC is an audio data-conversion IC that accepts digital PCM samples and produces corresponding analog voltage signals. Within the broader semiconductor hierarchy, the PCM1600YG4 is an audio DAC, a data-converter IC, and a signal-processing device used between digital audio sources and downstream analog amplification or line-output circuitry. The six-channel architecture reduces the number of separate converters required for surround-sound, home-theater, or multi-zone audio designs. Its 24-bit data resolution supports detailed digital audio representation, while operation up to a 96kHz sampling rate accommodates high-resolution audio streams. The serial interface reduces the number of data connections required between the DAC and a digital audio controller. The PCM1600YG4 is identified as an enhanced multilevel delta-sigma digital-to-analog converter. This architecture is appropriate for audio-frequency signal generation because it provides a digital conversion path designed for high-resolution multichannel playback. The device accepts both analog and digital supply sources, allowing the system designer to manage noisy digital and sensitive analog supply domains separately. Typical uses include home-theater audio, multichannel receivers, digital active speakers, AV receivers, soundbars, and professional audio equipment requiring six simultaneous analog outputs. The 48-LQFP package also provides adequate pin count for dedicated analog outputs, digital control signals, and power-related connections in a conventional PCB design. Layout is critical because analog output stages can be affected by switching noise and ground-current coupling. Place analog and digital supply decoupling according to the manufacturer datasheet, route the six analog output channels away from high-current digital paths, and use a quiet ground strategy for the analog section. Confirm output-buffer loading, digital-interface levels, and supported operating modes before finalizing the schematic. This product page combines the verified device identity and package details with practical integration guidance for multichannel audio systems. It also identifies replacement constraints clearly, explains where the manufacturer documentation should be consulted, and organizes the PCM1600YG4 specifications for rapid engineering review and sourcing.

RFQ צור קשר
PCM1601Y - 24-Bit 96kHz 6-Channel Audio DAC | Texas Instruments
PCM1601Y

PCM1601Y - 24-Bit 96kHz 6-Channel Audio DAC | Texas Instruments

Texas Instruments PCM1601Y is a 24-bit, 96kHz sampling, six-channel, enhanced multi-level delta-sigma digital-to-analog converter in a 48-MQFP surface-mount package measuring 12mm by 12mm. It accepts I2S digital audio input and provides analog outputs for multichannel audio equipment. The converter supports 3.3V or 5V supply operation and accepts separate analog and digital supply sources, allowing system designers to partition supply requirements according to the analog and digital sections of the design. A multi-channel digital-to-analog converter is an analog-output interface that reconstructs digital PCM audio samples as continuous analog voltage signals. The PCM1601Y belongs to the delta-sigma DAC family, a converter architecture that uses high-frequency oversampling and digital noise shaping to produce a multi-bit analog output from a one-bit internal quantizer. As a six-channel DAC, it can support surround-sound, home-theater, CD-player, DVD-player, and other multichannel audio systems without requiring six separate converter packages. The PCM1601Y provides 24-bit resolution and supports sampling rates up to 96kHz. Its enhanced multi-level architecture is intended to improve linearity and reduce quantization-related distortion relative to simpler converter implementations. The device also accepts 3V to 3.6V or 5V supply configurations, while the availability of separate analog and digital supply connections helps reduce coupling between digital switching activity and sensitive analog output circuitry. Its 48-MQFP package provides a compact surface-mount solution with 0.8mm terminal pitch. The converter is designed for audio systems that require six synchronized analog outputs and an I2S-format digital interface. The 96kHz maximum sampling rate supports high-resolution digital audio sources, while 24-bit data resolution preserves a large numerical range for audio processing. Because the output stage still requires appropriate analog filtering and signal-path design, converter resolution alone does not determine final system signal-to-noise ratio or distortion performance. Those results also depend on clocking, grounding, supply implementation, analog output loading, and the selected reconstruction or post-filter network. Typical PCM1601Y applications include home-theater audio receivers, DVD and CD players, multichannel amplifiers, active speaker electronics, automotive entertainment systems, and professional audio equipment. In each case, the six outputs can serve as the front-left, front-right, center, surround-left, surround-right, and subwoofer channels of a standard surround layout. The converter is particularly useful where multiple digital audio channels must be converted while preserving a common I2S source and sample clock. System design should give particular attention to analog and digital supply routing. The separate analog and digital supply pins should be connected to appropriately filtered sources, with grounding arranged to minimize return-current coupling from digital signals into the analog output network. Decoupling capacitors should be placed close to the relevant supply pins, and the external clock and I2S data lines should be routed away from sensitive analog outputs. The manufacturer datasheet and pinout must be checked against the exact board revision before finalizing the schematic or PCB layout. This product record combines distributor specifications, package information, sourcing details, and engineering guidance for the PCM1601Y. It also separates verified PCM1601Y attributes from parameters that require confirmation from the current Texas Instruments datasheet, helping designers evaluate the six-channel DAC without treating incomplete search snippets as complete device specifications.

RFQ צור קשר
PCM1602KY - 24-Bit 6-Channel 192kHz Audio DAC | Texas Instruments
PCM1602KY

PCM1602KY - 24-Bit 6-Channel 192kHz Audio DAC | Texas Instruments

The Texas Instruments PCM1602KY is a 24-bit, 6-channel enhanced multilevel delta-sigma digital-to-analog converter supporting sampling rates up to 192 kHz and housed in a 48-pin LQFP package. It is designed for multichannel audio systems that require six simultaneous analog output channels, high-resolution digital audio processing, and compact PCB integration. The device is identified as an I2S-compatible audio DAC in its PCM1602KY/2K ordering variant. An audio digital-to-analog converter is a signal-conversion IC that transforms digital audio samples into analog voltage signals suitable for amplification, mixing, recording, or line-level output. Within the signal-chain hierarchy, the PCM1602KY belongs to the DAC family, then to audio converters, interface ICs, and ultimately the broader semiconductor category. Six-channel integration reduces the number of separate converter packages required in home-theater, professional audio, and multichannel playback equipment. The converter operates with 24-bit resolution, reaches a maximum sampling rate of 192 kHz, and provides six output channels. Its enhanced multilevel delta-sigma architecture is intended to support high-resolution audio reconstruction while integrating the digital-to-analog function into one package. The 48-LQFP package provides 48 externally accessible terminals and is suitable for conventional multilayer PCB layouts using surface-mount assembly. Available device information identifies a maximum analog output of 3.41 V, a settling time of 400 microseconds, and an operating temperature range of -25 °C to +85 °C. These ratings define important selection boundaries: the analog output must remain compatible with the downstream amplifier, and the converter should be operated only within its specified temperature range. The 192 kHz capability supports high-resolution source material and professional audio workflows requiring more than the 48 kHz CD base rate. Typical uses include multichannel home-theater preamplifiers, surround-sound audio receivers, active speaker controllers, digital mixing consoles, professional monitoring equipment, and automotive infotainment systems. The six-channel architecture is especially useful when a system requires synchronized analog outputs from one digital audio source. System integrators must still design the digital interface, analog output filtering, grounding, and output coupling around the converter’s specified operating conditions. PCB implementation requires careful treatment of analog and digital return paths, short routing for interface signals, and a stable low-noise supply arrangement. Decoupling should be placed close to the corresponding supply pins, while analog output components should avoid sharing high-current return paths with digital switching circuitry. The six-channel structure reduces package count but still requires balanced component placement and symmetrical routing to minimize channel-to-channel differences. This page consolidates the PCM1602KY’s resolution, channel count, sampling rate, package, operating limits, sourcing path, and application guidance into an engineering-focused reference. It also distinguishes direct ordering variants from true functional alternatives so designers can verify compatibility before committing to a board revision.

RFQ צור קשר
PCM1602Y - 24-Bit 192kHz 6-Channel DAC | Texas Instruments
PCM1602Y

PCM1602Y - 24-Bit 192kHz 6-Channel DAC | Texas Instruments

The Texas Instruments PCM1602Y is a 24-bit, 192kHz sampling, 6-channel enhanced multilevel delta-sigma digital-to-analog converter with an I2S interface, housed in a 48-LQFP 7x7mm surface-mount package. It is designed for high-fidelity multichannel audio systems requiring six digital audio conversion channels in one integrated component. A DAC is a digital-to-analog converter, a signal-conversion IC that transforms sampled digital audio into corresponding analog voltage signals. The PCM1602Y belongs to the broader hierarchy of DAC, audio converter, signal-conversion IC, and semiconductor. Its six-channel architecture reduces the number of separate converters required when reproducing multichannel sound, while the I2S interface supports integration with digital audio processors, receivers, and consumer-audio equipment. Principal features include 24-bit resolution, a maximum sampling rate of 192kHz, and six-channel conversion. The I2S interface provides a conventional digital-audio connection to the surrounding system. The device also uses an enhanced multilevel delta-sigma conversion architecture, combining high-resolution digital-to-analog conversion with an integrated audio-converter format suitable for consumer and professional equipment. Its 48-LQFP package measures 7x7mm. The PCM1602Y supports separate analog and digital supply sources, allowing analog and digital sections to be connected to suitable supply rails. A documented alternative-source description states supply ranges of 3V to 3.6V and 5V, although exact rail assignments and detailed operating limits should be confirmed in the manufacturer datasheet. Because the converter handles six channels, careful treatment of digital clocking, analog output filtering, grounding, and supply decoupling is essential to preserve audio quality. Typical uses include multichannel home-theater audio, powered speakers, AV receivers, digital active speakers, automotive audio systems, and professional playback equipment. The 192kHz sampling capability makes the device appropriate for high-resolution source material, while the six-channel output count suits surround-sound and multi-zone audio architectures. System designers must still ensure that the host processor supplies valid I2S data, required timing, and an appropriate master-clock relationship. For implementation, place decoupling capacitors close to the supply pins and keep the digital interface traces away from sensitive analog output paths. Confirm the manufacturer's recommended analog-output topology and external component values before production. Also verify the exposed-pad, thermal, and PCB-layout requirements associated with the 48-LQFP package rather than relying only on generic package guidance. This page consolidates the verified 24-bit, 192kHz, six-channel, I2S, and 48-LQFP characteristics with distributor pricing, a verified same-package alternative, comparison guidance, and practical integration considerations. It is intended to help engineers evaluate sourcing and design fit while clearly identifying details that still require confirmation from the official datasheet.

RFQ צור קשר
PCM1602Y/2K - 24-Bit 6-Channel 192kHz DAC | Texas Instruments
PCM1602Y/2K

PCM1602Y/2K - 24-Bit 6-Channel 192kHz DAC | Texas Instruments

The Texas Instruments PCM1602Y/2K is a 24-bit, six-channel, enhanced multilevel delta-sigma digital-to-analog converter operating at up to 192 kHz. It supports an I2S digital audio interface, provides a maximum analog output of 3.41 V, and is packaged in a 48-pin LQFP measuring 7 mm by 7 mm. Its nominal settling time is 400 microseconds, while the specified operating temperature range is -25°C to +85°C. An audio DAC is a mixed-signal semiconductor that converts digital PCM audio samples into left- and right-channel analog voltage signals. A six-channel DAC can drive three stereo pairs, making the device suitable for multichannel audio equipment, home-theater systems, digital mixing consoles, and active speaker designs. Within the broader hierarchy, PCM1602Y/2K belongs to the audio DAC, data converter, and signal-conversion IC categories. The primary features of PCM1602Y/2K include 24-bit resolution, a 192 kHz maximum sampling rate, six output channels, enhanced multilevel delta-sigma architecture, and an I2S interface. The six-channel architecture reduces the number of separate stereo DACs required in a multichannel design, while the 192 kHz capability supports high-resolution audio signal paths. Its 48-LQFP package provides a defined surface-mount footprint for audio equipment with moderate connector density. The enhanced multilevel delta-sigma architecture performs digital-to-analog conversion by shaping quantization noise away from the signal band and reconstructing the analog waveform through an internal conversion network and output stage. The 3.41 V maximum analog output provides a defined upper limit for the converter's analog output range. Its 400 microsecond nominal settling time describes the response interval associated with the device's settling behavior and is an important consideration when channels must be initialized or updated in a controlled sequence. Typical uses include six-channel consumer audio receivers, home-theater preamplifiers, digital mixing consoles, multichannel headphone and line-output boards, active loudspeaker electronics, and professional audio interfaces. In each case, the I2S interface can accept digital audio from a source processor, while six analog outputs reduce channel-conversion component count. Stereo-only equipment would use only the required channel pairs, but the unused outputs must still be handled according to the manufacturer’s application guidance. The most important design consideration is analog-output implementation. Follow the manufacturer’s reference circuit for output filtering, grounding, bypass capacitance, and digital-interface timing, and preserve the specified 3.41 V maximum analog output. Keep high-current digital and switching circuitry away from the analog output network, and use a quiet ground-plane strategy to reduce channel-to-channel noise coupling. This product page organizes the converter’s verified capabilities, package information, sourcing paths, application guidance, and available same-footprint comparison. It also separates practical design guidance from raw specifications so engineers can evaluate the PCM1602Y/2K for multichannel audio systems before committing to a board design.

RFQ צור קשר
PCM1604PT - 24-Bit 6-Channel 200kHz Audio DAC | Texas Instruments
PCM1604PT

PCM1604PT - 24-Bit 6-Channel 200kHz Audio DAC | Texas Instruments

Texas Instruments PCM1604PT is a 24-bit, six-channel digital-to-analog converter for audio signal generation, supporting operation up to 200 kHz and serial I2S data transfer. The device combines six DAC channels, analog and digital supply connections, and a 48-pin LQFP package measuring 7 mm by 7 mm. According to the manufacturer datasheet, its dynamic range reaches 105 dB, making it suitable for multichannel consumer, automotive, and industrial audio systems. An audio DAC is a mixed-signal integrated circuit that converts digitally encoded audio samples into proportional analog voltages. In the signal hierarchy, the PCM1604PT belongs to the digital-to-analog converter category within ADC/DAC and mixed-signal semiconductor devices. Six integrated channels can reduce the number of external converter packages needed in surround-sound, home-theater, automotive audio, and multichannel instrument systems. The 24-bit interface supports high-resolution digital audio, while the 200 kHz capability provides additional sampling-rate headroom for professional and premium consumer equipment. The 105 dB dynamic-range figure represents the converter's signal-to-noise and distortion performance, making channel-to-channel noise differences an important consideration in multiway audio systems. Both analog and digital supply domains are identified in the device documentation, allowing power architecture and grounding to be planned separately. The PCM1604 architecture is intended for synchronous serial audio systems using I2S-format data. System-level clocking must preserve the required relationship between the audio serial clock, bit clock, frame sync, and master clock. The 48-LQFP footprint offers more interconnect capacity than a small leadless package, supporting six analog output channels as well as digital data, clock, control, and power connections. Typical applications include 5.1 and 7.1-channel home-theater receivers, automotive infotainment audio systems, active speaker networks, digital mixing consoles, surround-sound processors, and multichannel audio interface equipment. Selection should consider the 24-bit resolution, six-channel integration, 200 kHz operating capability, 105 dB dynamic range, and the exact 48-LQFP footprint against board area and signal-routing requirements. Keep analog output routing short and away from digital clock and I2S data traces. Use a quiet analog ground strategy, decouple the analog and digital supply domains locally, and follow the pin-description and layout guidance in the manufacturer datasheet. Verify output-filter component values and amplifier coupling requirements for the intended sample rate rather than copying values between unrelated codec families. This page combines channel and interface characteristics, package-focused alternatives, application guidance, comparison parameters, and PCB design cautions to support faster component selection and implementation of the PCM1604PT in multichannel audio equipment.

RFQ צור קשר
PCM1604PTR - 24-Bit 6-Channel Audio DAC | Texas Instruments
PCM1604PTR

PCM1604PTR - 24-Bit 6-Channel Audio DAC | Texas Instruments

The Texas Instruments PCM1604PTR is a 24-bit, six-channel audio digital-to-analog converter with a maximum sampling frequency of 200 kHz, an I2S serial interface, and a 48-LQFP package measuring 7 mm by 7 mm. It converts six digital audio channels into simultaneous analog outputs for multichannel audio equipment, making it suitable for surround-sound systems, home-theater receivers, digital mixing consoles, and professional audio interfaces. An audio DAC is a mixed-signal semiconductor that reconstructs continuous analog waveforms from digital PCM samples. A DAC belongs to the digital-to-analog converter category, which is part of the broader ADC/DAC and signal-conversion semiconductor hierarchy. The PCM1604PTR uses a serial digital interface to receive multichannel audio data and separate analog and digital supply domains to support its conversion circuitry. Its six-channel architecture reduces the number of converters required in a multichannel signal path. The principal specifications are 24-bit resolution, six DAC channels, and operation up to 200 kHz. The I2S interface supports integration with digital audio processors, receivers, and source equipment. The converter also provides a 105 dB dynamic range, as stated in the manufacturer datasheet information indexed for this part, making it relevant to audio designs where preserving low-level signal detail and minimizing audible noise are important. Separate analog and digital power connections allow the PCB power architecture to control noise coupling. The PCM1604PTR is specified for a -25 °C to 85 °C operating-temperature range and is supplied in a 48-LQFP package. The TR suffix corresponds to tape-and-reel packaging for automated manufacturing. Its 7 mm square land pattern supports compact multichannel designs while retaining a conventional leaded package that can be inspected and assembled using established surface-mount processes. Typical applications include 5.1-channel and 7.1-channel audio decoding, multichannel digital amplifiers, surround-sound receivers, recording and playback equipment, active speakers, and professional audio mixers. The six integrated channels also suit test and measurement systems requiring multiple synchronized analog outputs. System designers should treat digital clocking, analog output filtering, grounding, supply decoupling, and channel mapping as the principal implementation concerns. For the cleanest result, use the application circuit in the Texas Instruments PCM1604 datasheet as the reference topology. Place analog and digital supply decoupling close to their respective pins, maintain the recommended analog and digital ground arrangement, and route the I2S clock and data signals away from sensitive output networks. Confirm the board-level filter and output-loading design against the required bandwidth and load before production release. This product page consolidates the key channel-count, resolution, interface, package, temperature, and lifecycle information into an engineer-oriented summary. It also compares verified same-package options and identifies where a redesign or manufacturer cross-reference check is required when an exact six-channel, 48-LQFP replacement cannot be confirmed.

RFQ צור קשר
PCM1604Y - 24-Bit 192kHz 6-Channel DAC | Texas Instruments
PCM1604Y

PCM1604Y - 24-Bit 192kHz 6-Channel DAC | Texas Instruments

The Texas Instruments PCM1604Y is a 24-bit, 192kHz sampling, six-channel enhanced multilevel delta-sigma digital-to-analog converter in a 48-LQFP 7x7 mm package. It accepts I2S-formatted digital audio data and converts six audio channels into simultaneous analog outputs. The converter is designed for multichannel audio systems requiring 24-bit resolution, operation up to 192kHz, and a dedicated six-channel DAC architecture. An audio DAC is a mixed-signal semiconductor that reconstructs continuous analog voltage signals from sampled digital audio data. Within the product hierarchy, PCM1604Y is a delta-sigma DAC, which is a digital-to-analog converter type, and ultimately belongs to the broader ADC/DAC and mixed-signal integrated-circuit categories. Delta-sigma architecture is widely used in digital audio because it supports high-resolution conversion, integrated digital filtering, and direct interface with common audio serializers. Key verified features include 24-bit resolution, a maximum sampling rate of 192kHz, six audio channels, enhanced multilevel delta-sigma operation, and I2S data input. These capabilities distinguish the PCM1604Y from lower-channel or lower-resolution converters. The six-channel architecture can reduce the number of separate DAC packages required in a surround-sound, home-theater, professional audio, or other multichannel system, provided the associated analog, clocking, and interface circuitry is designed correctly. The PCM1604Y accepts digital audio through I2S and supplies six analog output channels, making it suitable for designs in which one package handles all primary channel conversions. Its 48-LQFP package provides 48 external terminals and a square 7x7 mm footprint. Because no manufacturer pinout, electrical limits, or recommended application-circuit details were included in the supplied verified data, its clock requirements, output topology, supply voltages, dynamic range, distortion, channel isolation, and decoupling configuration should be confirmed in the manufacturer datasheet before schematic capture. Typical use cases include 5.1-channel and 7.1-channel home-theater receivers, multichannel active speaker systems, AV receivers, digital mixing consoles, audio interfaces, and automotive entertainment systems. In these applications, the PCM1604Y can convert six synchronized I2S channels before line-level amplification, speaker amplification, headphone amplification, or further analog processing. System partitioning should account for the converter's required clocks, analog supplies, output network, and digital input voltage compatibility. A critical design step is to verify the exact 48-pin signal mapping, exposed-pad requirements, supported audio formats, and master-clock relationships against the Texas Instruments datasheet before routing the PCB. Decoupling and analog-output layouts should be developed from the manufacturer's reference design rather than inferred from generic DAC guidance, because unsupported pin assignments, supply values, or output-network assumptions could invalidate the design. This page consolidates the verified distributor and manufacturer-facing information for PCM1604Y with package details, sourcing links, engineering cautions, and an honest assessment of available drop-in alternatives. The comparison focuses on what can be substantiated from the supplied records and explicitly identifies electrical, lifecycle, pinout, pricing, and replacement data that still requires confirmation.

RFQ צור קשר