מוצרים (44,000+)

PI7C9X1172BLE - I2C/SPI to Dual UART Bridge Controller | Diodes Inc
PI7C9X1172BLE

PI7C9X1172BLE - I2C/SPI to Dual UART Bridge Controller | Diodes Inc

The Diodes Incorporated PI7C9X1172BLE is an I2C-bus/SPI to dual-channel high-performance UART bridge controller rated for data rates up to 33 Mbps, with 64-byte FIFO buffers and up to eight programmable general-purpose I/O pins, housed in a 28-pin TSSOP package (4.40 mm body width) and powered from 1.8 V, 2.5 V or 3.3 V supplies. A UART bridge controller is a serial interface IC that translates a short-reach, chip-to-chip serial protocol into one or more asynchronous serial links. The PI7C9X1172 places an I2C-bus or SPI host port on one side and two independent UART channels on the other, so a microcontroller, SoC or FPGA can add two RS-232/RS-485-style serial ports over a bus it already has. In the wider hierarchy it sits as an interface controller between the embedded processing domain and the communications domain, alongside transceivers, level shifters and protocol converters. Key features include dual UART channels operating up to 33 Mbps, 64-byte transmit and receive FIFOs per channel for host-burst tolerance, eight configurable GPIO that can be routed to interrupt or general use, and low operating and sleeping current for battery-powered designs. The I2C-bus interface is compliant with Standard-mode and Fast-mode specifications, and the SPI port offers an alternative host connection where higher clock rates or more pins are available. Architecturally the device separates a synchronous host-side protocol engine from the two independent UART receivers and transmitters, each with its own FIFO, baud-rate generator and framing control. This lets a single host port service two full-duplex serial links simultaneously, and it is why the part fits compact handheld and battery-operated equipment where board area, standby current and cost dominate the design trade-off. Typical applications include handheld POS and barcode terminals, industrial data-capture and test equipment, USB-to-dual-serial dongles, multifunction printers, and battery-powered portable instruments that need two legacy serial ports bridged onto an I2C or SPI host bus. When designing around this device, keep the I2C pull-ups sized for the bus capacitance and the fastest mode you intend to run, confirm that the host firmware can service both FIFO interrupts, and note that the eight GPIO pins are shared resources that must be assigned in the pin-multiplexing configuration. Provide local decoupling close to the supply pins and respect the level-shift requirements of any external RS-232 or RS-485 transceiver. This page consolidates the manufacturer interface specification, package and supply details, drop-in replacement options and applied design guidance in one place, giving engineers a faster path from part selection to a working schematic than the raw datasheet alone provides.

RFQ צור קשר
PI7C9X1172BZHEX - Dual UART I2C/SPI Bridge | Diodes
PI7C9X1172BZHEX

PI7C9X1172BZHEX - Dual UART I2C/SPI Bridge | Diodes

Diodes Incorporated PI7C9X1172BZHEX is a serial-interface bridge integrated circuit that converts I2C or SPI transactions into two-channel UART communication. The device operates from 1.8 V, 2.5 V, or 3.3 V supply rails and is packaged in a 32-QFN housing measuring 5 mm by 5 mm. Its principal function is to bridge a serial bus used by a host or embedded controller with two independent UART channels used by external equipment. An I2C/SPI-to-UART bridge is an interface IC within the broader serial-interface and communication-controller category. It allows equipment that lacks convenient UART peripherals to exchange serial data through a host-oriented I2C or SPI bus. The PI7C9X1172BZHEX can therefore serve as a protocol-conversion and I/O-expansion element in systems that need to connect serial peripherals, control ports, or communication modules without dedicating multiple UART channels in the main controller. The key documented characteristics include support for I2C and SPI host-side protocols, two UART channels, operation from 1.8 V, 2.5 V, or 3.3 V supplies, and a compact 32-QFN package. The 5 mm by 5 mm QFN construction supports dense PCB layouts, although its exposed-pad thermal and layout requirements must be implemented according to the manufacturer's package information. Because the package has 32 terminals, its footprint requires careful fanout routing between the fine-pitch perimeter pads and the exposed thermal pad. The device is positioned for embedded control, industrial communication, instrumentation, and equipment-connection applications where an existing I2C or SPI processor interface must provide access to two UART channels. The selectable 1.8 V, 2.5 V, and 3.3 V operating options also permit integration with common low-voltage digital systems. Exact UART baud-rate limits, I2C/SPI timing, logic thresholds, electrical characteristics, and channel-configuration details should be confirmed in the manufacturer datasheet before a production design is released. Typical implementations place the bridge beside the controlled peripheral and connect the host controller through I2C or SPI. Software then performs protocol translation while the UART side connects to the target equipment. A key design consideration is matching the bridge's supply voltage, host-bus logic levels, pin multiplexing, and UART signal requirements to the connected devices. Decoupling and exposed-pad handling should follow the manufacturer's recommended layout to limit supply disturbance and maintain reliable operation in compact assemblies. This product page consolidates the confirmed interface function, supply options, package details, sourcing information, and replacement analysis into an engineering-focused reference. The PI7C9X1172BZHEX is most appropriate when a design requires a dedicated I2C/SPI-to-dual-UART bridge in a 32-QFN footprint. Production adoption should include verification of the complete electrical specification, pin assignment, timing limits, and package drawing against the current manufacturer documentation.

RFQ צור קשר
PI7C9X1172CLE - 33Mbps Dual UART Bridge | Diodes Incorporated
PI7C9X1172CLE

PI7C9X1172CLE - 33Mbps Dual UART Bridge | Diodes Incorporated

Diodes Incorporated PI7C9X1172CLE is an I2C-bus and SPI to dual-channel UART bridge controller capable of data rates up to 33 Mbps. It operates from 1.62 V to 3.63 V, provides up to eight programmable GPIO pins, and is packaged in a 28-pin TSSOP. The device also supports hardware and software flow control, automatic RS-485 direction control, fractional baud-rate generation, loopback self-test, soft reset, and a low-power mode. A protocol bridge is an interface IC that translates commands and data between unlike communication buses. The PI7C9X1172 belongs to the interface-controller hierarchy, connecting an I2C-bus or SPI controller on the host side to two independent UART channels on the peripheral side. This arrangement allows a compact embedded system to use a serial processor interface while supporting two conventional serial ports, RS-485 links, or other UART-based equipment. The PI7C9X1172's principal advantages include support for data rates as high as 33 Mbps, separate hardware and software flow-control mechanisms, and automatic control of RS-485 transmitter direction. Its eight programmable GPIO pins provide additional discrete digital signals without requiring a separate general-purpose I/O expander. A low-power operating mode is useful in battery-powered and handheld equipment where continuous high-speed operation would increase energy consumption. Internally, the controller supports fractional baud-rate generation, allowing the programmed UART baud rate to be represented more precisely than with integer-only divider schemes. Hardware flow control uses modem-control signals, while software flow control can be handled through the bridge protocol. Automatic RS-485 direction control simplifies half-duplex transceiver implementations by reducing the amount of host software required to manage the transmit and receive intervals. An internal loopback and self-test mode can assist board bring-up and fault isolation. Typical applications include industrial serial gateways, battery-powered data loggers, portable test equipment, RS-485 concentrators, embedded data-acquisition systems, and host adapters that must expose two UART channels through an I2C or SPI processor bus. These uses benefit from the device's combination of dual-channel UART connectivity, high supported data rate, programmable GPIO resources, and low-voltage operation. Designers should account for signal integrity, voltage levels, flow-control timing, and the electrical requirements of attached UART transceivers when assigning the device. The 28-TSSOP footprint supports compact PCB layouts, but the bridge cannot directly drive a long RS-485 cable; an appropriate line transceiver remains required. Review the manufacturer datasheet for the complete pin-description table, electrical limits, register definitions, and recommended application circuit before releasing a design. This product page combines the manufacturer's architecture and feature information with package details, interface-use guidance, practical design notes, and sourcing support for engineers evaluating the PI7C9X1172CLE. Use the Request a Quote form on this page for current commercial availability and lead-time information.

RFQ צור קשר
PI7C9X1172CZHEX - 33Mbps I2C/SPI to UART Bridge | Diodes
PI7C9X1172CZHEX

PI7C9X1172CZHEX - 33Mbps I2C/SPI to UART Bridge | Diodes

The Diodes Incorporated PI7C9X1172CZHEX is a dual-channel I2C/SPI-to-UART bridge controller supporting UART data rates up to 33 Mbps in a 32-pin TQFN package measuring 5 mm by 5 mm. It provides an I2C-bus/SPI controller interface, two high-performance UART channels, and up to eight programmable GPIO pins for compact serial-interface designs. An I2C/SPI-to-UART bridge controller is a type of interface IC that translates between a host serial bus and independent UART channels. It sits between a microcontroller or processor and an embedded serial subsystem, allowing one host bus to connect to multiple UART peripherals while reducing the number of host I/O pins required. In the broader hierarchy, the device belongs to the interface-controller family within integrated circuits and embedded communication semiconductors. Key features include a maximum UART data rate of 33 Mbps, support for I2C Standard-mode and Fast-mode operation, dual UART channels, and as many as eight additional programmable GPIO pins. The 32-pin TQFN package also supports compact board layouts in industrial controls, communications equipment, embedded systems, and test systems where several serial functions must share a limited connector or routing area. The PI7C9X1172 family combines an I2C host interface, SPI support, UART framing, and programmable parallel I/O in one controller. The I2C interface uses the standard SDA and SCL lines, while the UART side provides two channels capable of high-speed serial transfer. Low operating and sleeping current are stated design goals, making power-conscious control of the serial subsystem possible when the system is not actively exchanging data. Typical uses include industrial serial gateways, programmable logic and test equipment, embedded control boards, peripheral expansion, and compact communications modules. The dual-channel architecture is especially useful when an embedded controller must monitor or control two independent UART-linked subsystems through one I2C or SPI host connection. Board design should keep I2C traces short, provide the pull-up network required by the selected bus speed, and route UART signals with return-path discipline. Because this version uses a 32-pin TQFN package, verify the exposed-pad connection, land pattern, and thermal strategy against the manufacturer pin-description and package drawings before layout release. This page organizes the controller’s interface capabilities, package constraints, application guidance, comparison data, and sourcing options into a practical engineering reference that supports both initial component selection and PCB implementation.

RFQ צור קשר
PI7C9X118SLFDEX - PCIe-to-PCI Bridge | Diodes Incorporated
PI7C9X118SLFDEX

PI7C9X118SLFDEX - PCIe-to-PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C9X118SLFDEX is a PCIe-to-PCI bridge interface IC that translates one PCI Express x1 link into a 32-bit, 66 MHz PCI bus. It is packaged in a 128-terminal, 14 x 14 mm low-profile quad flat package with an exposed pad. The SlimLine family is engineered for systems that need to add a conventional PCI interface to a compact PCI Express design while preserving a small board footprint. A PCI Express-to-PCI bridge belongs to the interface IC category and sits between high-speed serial computer buses and older parallel peripheral buses. PCIe uses serial point-to-point links, while the PCI side of this device exposes the legacy parallel bus. This bridge allows desktop, workstation, ultra-mobile, and system-module architectures to retain compatibility with PCI peripherals without implementing a separate host adapter. The PI7C9X118SL is performance tuned for x1 PCI Express to 32-bit/66 MHz PCI bridging and is positioned for low-power, space-constrained systems. Its stated 128-LQFP package includes an exposed thermal pad, providing a large-area connection for heat dissipation on multilayer PCBs. The FDEX ordering suffix identifies the specific leaded LQFP package and exposed-pad configuration used in this listing. The component is used as a bus-interface controller rather than as a general-purpose processor, memory device, or transceiver. Its primary design task is protocol conversion, clocking, buffering, and arbitration between the PCI Express endpoint-facing interface and the legacy PCI bus. System firmware and operating-system support remain necessary for a complete bridge implementation, and board-level validation should confirm timing, power sequencing, and peripheral compatibility. Typical uses include PCI Express system modules, industrial and embedded controller platforms, workstation peripherals, legacy PCI expansion systems, and compact computers requiring an x1-to-conventional-PCI pathway. In these applications, the exposed-pad package helps remove heat from the bridge during sustained transfer activity, while the 14 x 14 mm outline preserves more board area than a larger discrete bridge solution. Designers should follow the manufacturer's pin-description table and reference design when assigning the 128 package terminals, configuring local signals, and connecting the exposed pad. Input, output, power, ground, clock, and differential PCI Express routing must follow the exact pin definitions and recommended layout constraints to avoid signal-integrity or protocol-compliance problems. This page consolidates the verified device identity, package information, bridge function, lifecycle sourcing information, and practical implementation guidance. It also distinguishes documented characteristics from parameters that require confirmation from the manufacturer datasheet, helping engineers plan the board-level review without assuming electrical or timing values that are not established.

RFQ צור קשר
PI7C9X119SLFDEX PCIe-to-PCI Bridge | Diodes Incorporated
PI7C9X119SLFDEX

PI7C9X119SLFDEX PCIe-to-PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C9X119SLFDEX is a PCI interface integrated circuit configured as a Slimline PCIe-to-PCI reversible bridge. The device belongs to the PCI interface IC family and is supplied in a 128-pin low-profile quad flat package (LQFP-128) for surface-mount PCB assembly. It is intended for systems that must bridge a PCI Express interface to a conventional PCI bus while retaining the option to reverse the bridge configuration. The PI7C9X119SLFDEX is offered in tape-and-reel packaging with the X suffix, while the related PI7C9X119SLFDE ordering code uses tray packaging. A PCI Express-to-PCI bridge is an interface controller that adapts the serial point-to-point PCIe architecture to the parallel, shared-bus PCI specification. PCIe links use high-speed serial differential pairs, whereas a legacy PCI bus carries multiple parallel address and data signals. A reversible bridge is designed to support the bridge relationship in either system direction rather than functioning as a simple endpoint or repeater. This makes the device relevant to embedded, industrial, communication, and legacy-expansion platforms that must retain PCI equipment while adopting a PCIe host interface. The PI7C9X119 series is identified as a PCIe 2 six-port, eight-lane packet switch in the ExtremeLo family. Six ports and eight lanes provide the switching resources required to organize traffic between a PCIe system interface and PCI-facing resources. Reversible operation adds topology flexibility, allowing the same bridge silicon to be evaluated in either direction of the PCIe-to-PCI connection. Designers should nevertheless confirm lane allocation, port configuration, reference-clock requirements, reset behavior, and electrical routing against the manufacturer datasheet for the specific board design. The LQFP-128 package presents a substantial mixed-signal and high-speed implementation challenge. The design must route multiple high-speed differential pairs with controlled impedance, maintain length matching within the applicable PCIe receiver and transmitter tolerances, and provide low-noise return paths through the reference plane. The bridge also requires multiple supply rails, clocking, configuration, and peripheral interfaces, so careful partitioning of power, digital, and clock domains is essential for reliable operation. Typical uses include industrial controller upgrades that retain PCI expansion cards, communication equipment with mixed-generation backplanes, embedded systems that interface legacy PCI peripherals to a PCIe processor module, and test or transport systems requiring a configurable PCIe-to-PCI conversion stage. Reversible operation can simplify shared platform qualification when either side of the link must act as the controlling endpoint during different product configurations. The critical design consideration is signal integrity. Place the bridge close to the PCIe connector and connector-associated protection devices, follow the manufacturer reference layout for differential pairs, and provide the specified decoupling at every supply pin. Do not substitute generic bulk decoupling for the documented high-frequency network, and validate eye diagrams, compliance, and lane margin on the finished board. This page consolidates interface identification, package information, related ordering codes, practical PCB guidance, and application-oriented design context. It also distinguishes functional alternatives from true pin-to-pin replacements, helping engineers make a board-level decision rather than relying only on a matching interface description.

RFQ צור קשר
PI7C9X130DNDE - PCIe-to-PCI-X Reversible Bridge, 256-BGA | Diodes
PI7C9X130DNDE

PI7C9X130DNDE - PCIe-to-PCI-X Reversible Bridge, 256-BGA | Diodes

The Diodes Incorporated PI7C9X130DNDE is a PCIe-to-PCI-X reversible bridge controller packaged in a 256-ball PBGA measuring 17 x 17 mm, operating from 1.8 V and 3.3 V supply rails and specified over the industrial -40C to +85C temperature range. A PCI Express bridge is a bus-controller integrated circuit that translates transactions between the PCIe serial interconnect and the legacy parallel PCI/PCI-X bus. The PI7C9X130 belongs to the bus-controller and interface-controller product class inside the broader interface-IC and semiconductor hierarchy, and it is specifically designed to let a modern PCIe host platform retain connectivity to legacy PCI-X expansion cards, instrumentation, or industrial add-in modules without redesigning the host board. Key features include fully reversible operation, meaning the bridge can operate with PCIe as the primary side and PCI-X as the secondary side, or in the reverse configuration with PCI-X primary and PCIe secondary. The device supports a maximum payload size of up to 512 bytes, and it implements PCI Bus Power Management Specification Revision 1.1 and Advanced Configuration and Power Interface Specification Revision 2.0b, which allows the bridge to place the legacy secondary bus into a low-power state when no card is active. Architecturally, the PI7C9X130 is a transparent and non-transparent bridging solution: in transparent mode the bridge forwards traffic without modifying it, while in non-transparent mode it provides a subtractive decode path for legacy devices. Configuration register behavior is backward compatible with existing PCI bridge software and firmware, so host drivers and BIOS code written for earlier bridges run without modification for the original operation, which drastically reduces software porting effort on legacy industrial platforms. Typical applications include industrial PCI-X instrumentation and test equipment, migration of PCI-X mezzanine cards onto PCIe hosts, server and workstation legacy expansion support, embedded control systems with legacy peripheral cards, and telecom or medical platforms that must bridge an older PCI-X backplane to a modern processor fabric. When designing around this device, pay close attention to the power-rail sequencing of the 1.8 V and 3.3 V domains and to the fact that the bridge is listed as not recommended for new designs. For new platforms, evaluate current-generation PCIe-to-PCI-X or PCIe-to-PCI alternatives first, and reserve the PI7C9X130 for sustaining existing designs and certified legacy equipment. This page combines manufacturer specification data, lifecycle status, a parameter-by-parameter comparison table against the closest family members, and practical design guidance covering layout, power, and legacy-bus integration that engineers normally have to piece together from several documents.

RFQ צור קשר
PI7C9X2G303ULZPE - 3-Port 3-Lane PCIe 2.0 Switch | Diodes
PI7C9X2G303ULZPE

PI7C9X2G303ULZPE - 3-Port 3-Lane PCIe 2.0 Switch | Diodes

Diodes Incorporated PI7C9X2G303ULZPE is a 3-port, 3-lane PCIe 2.0 packet switch intended for compact systems that require multiple PCI Express links. It is packaged in a surface-mount 136-pin aQFN package and mounted on a tray. The switch provides a practical way to fan out or route PCI Express traffic while supporting the physical-layer functions required by PCI Express links, including receiver detection for attached 50-ohm terminations. A PCI Express packet switch is a specialized interface integrated circuit that routes transactions between multiple PCIe endpoints and a host-facing uplink. Within the broader hierarchy of interface ICs, it sits between endpoint controllers and a PCI Express fabric. Unlike a simple repeater or standard I/O expander, a packet switch manages multiple lanes and multiple downstream ports, allowing equipment designers to add expansion connectivity without distributing PCI Express routing functions across multiple discrete devices. The primary PI7C9X2G303ULZPE configuration is 3 ports and 3 lanes. This architecture is useful where one upstream link must feed several downstream functions, such as a network appliance with multiple controllers, an embedded computing system with storage and peripheral links, or a test platform requiring controlled PCI Express fanout. The device operates in the PCI Express 2.0 ecosystem, making it appropriate for systems designed around Gen1-compatible electrical infrastructure and conventional 5 GT/s-class link requirements. Diodes Incorporated describes the switch as an ExtremeLo PCIe 2.0 packet switch in its PI7C9X2G303EL family documentation. The family’s physical-layer circuits include receiver detection, which identifies the presence of an attached 50-ohm-to-ground termination. This function helps the transmitter establish the correct electrical interface state when a connector or cable is present. The target PI7C9X2G303ULZPE uses the ZPE ordering suffix, while the PI7C9X2G303ELBZXE member is also associated with a 136-aQFN, 8 mm by 8 mm package configuration. Typical uses include industrial controllers, embedded servers, communications equipment, PCIe expansion chassis, storage controllers, and automated test systems. In these applications, the switch can reduce the number of separate PCI Express routing components, centralize port management, and simplify the relationship between an upstream root complex and downstream endpoint devices. System partitioning still depends on operating-system support, device drivers, interrupt routing, BAR assignment, and the electrical compatibility of every attached endpoint. PCB implementation requires careful high-speed signal routing, continuous reference planes, and compliant PCIe impedance geometry. The 136-pin aQFN package also needs an exposed thermal and electrical ground strategy that follows the manufacturer’s land pattern. Verify the exact pin functions, differential-pair assignments, reference clock requirements, power rails, and capacitor placement against the PI7C9X2G303EL datasheet before releasing a new layout. This product record combines the verified 3-port, 3-lane PCIe 2.0 configuration with manufacturer-family guidance, package information, practical PCB considerations, and a qualified replacement analysis. It is intended to accelerate component selection while keeping the final design tied to the manufacturer’s detailed electrical and reference-design requirements.

RFQ צור קשר
PI7C9X2G308GPNJE - PCIe 2.0 3-Port 8-Lane Switch
PI7C9X2G308GPNJE

PI7C9X2G308GPNJE - PCIe 2.0 3-Port 8-Lane Switch

The Diodes Incorporated PI7C9X2G308GPNJE is a GreenPacket PCIe 2.0 packet switch with three ports and eight aggregate lanes, packaged in a 196-LBGA measuring 15 mm by 15 mm. The device provides a PCI Express Gen 2 switching function for embedded, storage, network, and other platform designs. A PCIe packet switch is a semiconductor device that routes PCI Express traffic between a host or upstream endpoint and multiple downstream devices. In the wider hierarchy, it belongs to interface ICs and system-level interconnect silicon. Its three-port topology can consolidate multiple PCIe links while supporting packet processing and low-power behavior associated with GreenPacket technology. The primary features are the three-port architecture, eight-lane capability, PCIe 2.0 operation, and 196-LBGA package. The product brief identifies GreenPacket as Pericom's proprietary power-saving technology and describes the device as intended for embedded, storage, network, and other systems. The PI7C9X2G308GP family is also identified as compliant with lead-free system requirements. Technically, this component combines multiple PCI Express links in one switching fabric. The switching function can reduce the number of host-to-device paths in a system while providing centralized traffic management. Its eight-lane resource allocation should be evaluated against the combined bandwidth requirements of attached endpoints, because lane sharing can reduce per-device performance compared with a dedicated link. Typical uses include embedded computing platforms, storage controllers and enclosures, network appliances, and industrial systems that need more than one PCI Express endpoint behind a common interface. The manufacturer product brief specifically identifies embedded, storage, and network platforms as target applications for this packet-switch family. The most important design consideration is footprint and system compatibility. A 196-LBGA package requires careful ball assignment, multilayer PCB construction, appropriate escape routing, and compliant power distribution. Because the family is marked Not Recommended for New Design, engineers should confirm availability, lifecycle expectations, and any successor recommendations before starting a new design. This page combines the manufacturer product positioning, package and lifecycle information, sourcing guidance, and engineering-focused design considerations into a concise engineering reference for the PI7C9X2G308GPNJE.

RFQ צור קשר
PI7C9X2G404SLBFDE - 4-Port PCIe 2.0 Switch | Diodes
PI7C9X2G404SLBFDE

PI7C9X2G404SLBFDE - 4-Port PCIe 2.0 Switch | Diodes

Diodes Incorporated PI7C9X2G404SLBFDE is a 4-port, 4-lane PCI Express 2.0 packet switch in a 128-pin LQFP exposed-pad package. It supports two channels and is designed as a low-power, lead-free system component for embedded PCIe routing applications. The verified distributor data identifies it as a 4-port, 4-lane PCIe 2.0 packet switch; additional electrical characteristics were not supplied in the retrieved source set and are marked as required data below. A PCI Express packet switch is a semiconductor device that manages traffic between PCIe endpoints and a host or upstream port. It belongs to the packet-switch, interface-IC, and semiconductor hierarchies, using serialized high-speed lanes to distribute PCIe traffic among downstream devices. A four-port, four-lane configuration is useful when a system must consolidate storage, networking, graphics, or add-in-card connections behind a PCIe interface. The available data confirms four downstream ports, four lanes, PCIe 2.0 classification, two channels, a 128-pin LQFP package, and an exposed thermal pad. The package is identified as 14 x 14 mm by distributor data. The manufacturer description identifies embedded systems, Wi-Fi routers or gateways, printers, storage, combo cards, HBAs, and set-top systems as possible use cases. The switch is intended to provide a compact PCIe connectivity solution while keeping system power and board area under control. Its exact lane data rate, auxiliary voltage, operating temperature, reference-clock requirements, lane impedance, and electrical timing are not stated in the verified data, so those parameters remain explicitly unresolved rather than being inferred. PI7C9X2G404SLBFDE is suitable for board designs that require a PCIe switching function and a 128-pin LQFP land pattern. Design work should preserve the exposed-pad thermal and electrical requirements, validate the complete PCIe signal-integrity stack-up, and confirm pin-level functions against the manufacturer datasheet before layout release. This page consolidates verified distributor specifications, manufacturer product positioning, commercial availability information, and carefully qualified replacement findings. Because the provided evidence does not establish enough distinct pin-compatible devices, the alternatives section avoids padding the list with unsupported equivalents. For pricing, LCSC showed a starting price of $9.8100 and in-stock status in the retrieved results, while Mouser, DigiKey, Arrow, and other distributors provided listing or datasheet references. Pricing and availability should be reconfirmed at the time of purchase.

RFQ צור קשר
PI7C9X2G404SLQ - PCIe 2.0 4-Port Packet Switch AEC-Q100 | Diodes
PI7C9X2G404SLQ

PI7C9X2G404SLQ - PCIe 2.0 4-Port Packet Switch AEC-Q100 | Diodes

The Diodes Incorporated PI7C9X2G404SLQ is an automotive-compliant PCI Express 2.0 packet switch providing 4 ports over 4 lanes in a 128-pin LQFP (14x14 mm) package, qualified to AEC-Q100 and manufactured to meet lead (Pb)-free and green system requirements. A PCI Express packet switch is a switching fabric device that expands a single upstream PCIe root-port link into multiple downstream ports, allowing one host controller to communicate with several endpoints simultaneously. Within the system hierarchy, it sits between the PCIe controller (root complex) and endpoint devices, forming part of the interconnect layer of a computing or embedded platform alongside bridges and retimers. Key features of the PI7C9X2G404SLQ include its SlimLine low-power architecture, four-port/four-lane PCIe Gen2 topology, AEC-Q100 automotive qualification, and Pb-free green manufacturing. These attributes make it well suited to designs where lane count is limited but multiple PCIe endpoints must be supported, and where extended temperature and reliability requirements apply. Technically, the device belongs to the Pericom PI7C9X2G404SL packet-switch family (Diodes acquired Pericom Semiconductor). The SL (standard) and SLQ (automotive/qualified) variants share the same silicon architecture and SlimLine package; the SLQ variant is specifically characterized and qualified for automotive deployment. Compliance with the PCI Express Base Specification enables interoperability with standard root complexes and endpoints without custom drivers. Typical applications include automotive infotainment and telematics platforms, Wi-Fi routers and gateways, embedded industrial systems, storage controllers, HBAs, combo cards, and printers, where a cost-effective PCIe fan-out is required. A key design consideration: confirm lane allocation across the four downstream ports, since the device provides four lanes total; heavily loading one port with all four lanes starves the remaining ports. Verify power budget and reference-clock distribution per the manufacturer datasheet. This page synthesizes verified manufacturer data, drop-in alternatives, application guidance, and practical design notes not found in a single datasheet or distributor listing.

RFQ צור קשר
PI7C9X3G1224GPAHFCE - PCIe Gen3 12-Port 24-Lane Switch | Diodes
PI7C9X3G1224GPAHFCE

PI7C9X3G1224GPAHFCE - PCIe Gen3 12-Port 24-Lane Switch | Diodes

The Diodes Incorporated PI7C9X3G1224GPAHFCE is a PCI Express (PCIe) Gen3 packet switch supporting 24 lanes of 8 Gb/s Gen3 SERDES in flexible port configurations from 3 ports up to 12 ports, housed in a 324-ball H-FCBGA (19 x 19 mm) package shipped in tray form (84 pieces per tray). A PCIe packet switch is a switching fabric device that connects a root complex or upstream host port to multiple downstream endpoints, arbitrating and routing PCIe transaction-layer packets between ports. Within the system hierarchy, it sits at the fabric level of the PCIe architecture - above individual endpoint controllers and below the root complex - and is a key building block of server, storage, and expansion platforms that need more PCIe connectivity than a host CPU natively provides. Key features of the PI7C9X3G1224GP family include the flexible tile-based port architecture, where a basic cell called a tile consists of 8 ports and 16 lanes for Tile 0, allowing variable lane-width allocation per port; support for the PCIe Gen3 data rate of 8 GT/s per lane; and 24 total lanes that can be aggregated into wide ports (x4, x8) or split into narrow ports (x1, x2) depending on system topology requirements. Technically, the switch implements the full PCIe packet routing engine: it decodes TLP headers, performs address-based routing in the switch's internal hierarchy of virtual PCI-to-PCI bridges, and manages link training, equalization, and lane reversal on each SERDES interface. The architecture allows the flexible port configuration by allocating variable lane width for each port, so designers can tailor fan-out without changing silicon. Typical applications include server expansion backplanes, NVMe SSD storage controllers with multiple drive bays, PCIe expansion chassis, industrial host adapter cards, and communications platforms aggregating multiple endpoint cards onto a single host root port. When designing with this device, verify the port-to-lane mapping of the chosen package option against your board topology, and plan the power delivery and SERDES layout (controlled-impedance differential pairs, AC coupling, reference clock distribution) early, since 24 Gen3 lanes place significant demands on stackup and trace budget. This page synthesizes distributor availability data, drop-in alternatives within the PI7C9X3G1224GP family, and practical design notes not found in a single manufacturer datasheet.

RFQ צור קשר
PI7C9X3G816GP - 8-Port 16-Lane PCIe 3.0 Switch | Diodes
PI7C9X3G816GP

PI7C9X3G816GP - 8-Port 16-Lane PCIe 3.0 Switch | Diodes

The Diodes Incorporated PI7C9X3G816GP is a PCI Express Gen 3 packet switch that supports 16 lanes of Gen3 SERDES in flexible 2-port, 3-port, 4-port, 5-port and 8-port configurations, housed in a 324-ball HFCBGA (19x19 mm) package. A PCIe packet switch is an interface fabric device that sits in the PCI Express hierarchy between a root complex and multiple endpoints. It expands a single upstream PCI Express link into several downstream links, forwarding TLPs (Transaction Layer Packets) between ports based on address routing. Within the system hierarchy, a packet switch belongs to the PCI Express interconnect family: root complex to switch to endpoints, enabling fan-out expansion for storage controllers, network interface cards, and host adapters without saturating the host root port. Key features of the PI7C9X3G816GP include PCI Express Gen3 (8 GT/s) SERDES with 16 lanes total, flexible lane-width allocation per port, and support for 2-port through 8-port partitioning. This flexibility allows a single PCB design to address multiple SKU tiers: a 2-port x8 design for storage, or an 8-port x2 fan-out for dense backplanes. The switch implements standard PCI Express packet-switch functions including non-posted and posted transaction forwarding. Technically, the device integrates high-speed Gen3 SERDES blocks with receiver equalization and transmitter de-emphasis required for reliable 8 GT/s operation over backplane-length channels, while the switch fabric performs cut-through packet routing with address-based and ID-based forwarding per the PCI Express Base Specification. Typical applications include NVMe SSD storage systems, server expansion backplanes, industrial host adapter cards, and networking line cards where a host PCIe Gen3 root port must serve multiple endpoints. Design consideration: allocate one configuration strap set and verify lane-width partitioning early, since flexibly partitioned ports share the fixed 16-lane SERDES pool and the chosen partition determines ball usage. This page synthesizes datasheet facts, drop-in family alternatives, application guidance, and design notes not consolidated in the manufacturer datasheet.

RFQ צור קשר
PI7C9X440SLBFDE PCIe to USB 2.0 Host Controller | Diodes
PI7C9X440SLBFDE

PI7C9X440SLBFDE PCIe to USB 2.0 Host Controller | Diodes

The Diodes Incorporated PI7C9X440SLBFDE is a PCI Express to USB 2.0 host controller designed to add USB host connectivity to systems based on PCI Express. It is packaged in a 128-pin LQFP measuring 14 x 14 mm and supports the USB 2.0 and PCI Express functions associated with embedded systems, servers, storage equipment, industrial automation, medical systems, and peripheral expansion cards. A PCI Express to USB 2.0 host controller is an interface IC that bridges a PCI Express host system with downstream USB 2.0 devices. Within the broader semiconductor hierarchy, this device belongs to the interface-controller class, combining a PCI Express interface with a USB host interface for systems that need external peripheral connectivity without relying on a discrete add-in card. The principal product characteristics are its PCI Express-to-USB 2.0 bridging function, USB 2.0 host-controller implementation, and 128-pin LQFP package. Diodes describes the PI7C9X440SL family as a cost-effective solution that can be used in volume servers, storage systems, embedded equipment, medical products, industrial automation, networking systems, IP television equipment, peripherals, and PC add-in cards. The device also targets low-power, lead-free, and green-system requirements. The controller is useful when a system designer needs to expose conventional USB peripherals through a PCI Express-based architecture. Its implementation is most relevant to embedded and industrial equipment, where a dedicated USB host interface can simplify external data-transfer, configuration, storage, and service connections. Firmware, operating-system support, driver availability, and the surrounding PCI Express and USB signal paths must be validated for the target platform before production release. Use the manufacturer's pin-description table and application circuit when assigning board traces. High-speed PCI Express and USB differential pairs require controlled impedance, continuous reference planes, minimized stub lengths, and placement away from switching power-conversion nodes. The 14 x 14 mm LQFP also requires adequate thermal copper and careful examination of high-speed signal return paths. This page combines manufacturer positioning with purchasing guidance, application analysis, practical board-layout considerations, and an engineering comparison of identified related devices. It is intended to help hardware engineers evaluate interface compatibility before committing the PI7C9X440SLBFDE to a new PCI Express and USB 2.0 design.

RFQ צור קשר
PI7C9X440SLBFDEX PCIe-to-USB 2.0 Host Controller | Diodes
PI7C9X440SLBFDEX

PI7C9X440SLBFDEX PCIe-to-USB 2.0 Host Controller | Diodes

The Diodes Incorporated PI7C9X440SLBFDEX is a PCI Express-to-USB 2.0 host controller in a 128-pin LQFP package measuring 14 mm by 14 mm. It combines a PCIe interface with USB 2.0 host-controller functionality for systems that need to add USB connectivity to a PCI Express platform. The manufacturer datasheet identifies compliance with PCI Express Base Specification Revision 1.1, Open Host Controller Interface Specification Revision 1.0a, and Enhanced Host Controller Interface Specification Revision 1.0. A PCI Express-to-USB 2.0 host controller is an interface bridge that allows a PCI Express host system to manage USB 2.0 peripherals through an internal controller. It sits between PCI Express system fabric and USB devices, combining the PCIe physical and transaction interface with USB host-controller behavior. The PI7C9X440SL belongs to the broader interface-controller hierarchy: PCIe interface IC, host bridge, USB host controller, and interface semiconductor. The PI7C9X440SL family is designed for compact, low-power, lead-free, and green systems. Its supported system categories include volume servers, storage systems, embedded equipment, medical systems, industrial automation, networking, IP television, peripherals, and PCI add-in cards. The manufacturer describes the family as a cost-effective PCIe-to-USB 2.0 implementation, while the orderable PI7C9X440SLBFDEX is supplied in the 128-LQFP industrial package identified by the product listing. Technically, the controller follows PCI Express Base Specification Revision 1.1 and supports both Open Host Controller Interface Revision 1.0a and Enhanced Host Controller Interface Revision 1.0. This combination addresses systems that require USB host support alongside a PCI Express-based platform. The 128-pin LQFP provides a defined lead arrangement for multilayer PCB routing, while the listed package size supports integration with established embedded and add-in-card layouts. Typical implementations place PI7C9X440SLBFDEX between a PCI Express host and internal or external USB 2.0 ports. Server and storage designs can use it to consolidate USB host access in a compact controller implementation. Embedded, medical, and industrial systems can use the same controller family where a PCIe processor platform must service USB 2.0 peripherals without using a discrete USB host controller. PCB planning must follow the pin assignments, reference design, clock requirements, power rails, and layout guidance in the manufacturer datasheet. Because this controller combines differential PCIe signaling with USB 2.0 interface requirements, controlled impedance, clean power distribution, and careful connector or cable routing are essential. The exposed thermal pad information for the target package should be followed with adequate copper area and thermal via placement where required. This product record combines the manufacturer's controller specifications with exact-order-part packaging information, verified lifecycle purchasing references, and application-oriented design guidance. It also distinguishes the orderable PI7C9X440SLBFDEX from related family and package references so engineers can confirm footprint, protocol, and sourcing requirements before committing a design to production.

RFQ צור קשר
PI7C9X441SLFDEX - PCIe to USB Host Controller | Diodes
PI7C9X441SLFDEX

PI7C9X441SLFDEX - PCIe to USB Host Controller | Diodes

The Diodes Incorporated PI7C9X441SLFDEX is a PCIe-to-USB host controller interface IC designed for systems that require an internal host controller to manage USB connectivity. The exact package type, electrical ratings, supported USB version, lane configuration, operating-temperature range, and power-consumption limits are not stated in the available product records and must be confirmed from the manufacturer datasheet before PCB or firmware design begins. A PCIe-to-USB host controller is an interface integrated circuit that bridges the Peripheral Component Interconnect Express interface and Universal Serial Bus host functionality. Within the broader semiconductor hierarchy, it belongs to the interface-controller category, connects to the USB and PCI Express I/O ecosystem, and serves as an embedded connectivity block rather than a general-purpose processor, memory device, or power-management component. The PI7C9X441SLFDEX is identified specifically as a PCIe-to-USB host controller application part by Diodes Incorporated. Its exact electrical features remain unavailable in the cited product records, including operating and auxiliary supply ranges, USB data-signaling rates, reference-clock requirements, transceiver characteristics, and internal regulator behavior. These parameters determine whether the controller can operate with a target system’s connector, routing, power, and firmware architecture. The part number identifies a specific ordering configuration: PI7C9X441SLFDEX. The “441” device family designation appears in distributor and manufacturer-related listings, while “EX” is part of the exact ordering suffix. Before treating the EX configuration as identical to another family member, engineers should compare its package marking, temperature grade, lead-free status, and revision-specific pin assignments using the appropriate ordering-information table. Typical design contexts for a PCIe-to-USB host controller include industrial computers, embedded servers, data-acquisition systems, media appliances, set-top equipment, and service platforms that need a dedicated USB host interface rather than a device-only USB function. In each case, the controller must be paired with an appropriate connector, USB protection solution, clocking arrangement, firmware driver, and system-level power budget. The most important design step is to obtain the exact manufacturer datasheet and verify the complete pin list, reference schematic, electrical limits, layout guidance, and supported operating system or driver model. PCI Express routing also requires careful lane assignment, reference-clock planning, connector configuration, and signal-integrity review; the device description alone is not enough to freeze the design. This page consolidates the verified product identity, sourcing context, technical-data gaps, package uncertainty, and design questions surrounding PI7C9X441SLFDEX. Its practical value is to prevent assumptions about unreported electrical ratings or package compatibility and to direct engineers toward the datasheet, exact-ordering information, and PCB implementation resources needed for a safe controller integration.

RFQ צור קשר
PI7C9X442SLBFDE PCIe-to-USB 2.0 Switch | Diodes Incorporated
PI7C9X442SLBFDE

PI7C9X442SLBFDE PCIe-to-USB 2.0 Switch | Diodes Incorporated

The Diodes Incorporated PI7C9X442SLBFDE is a PCI Express-to-USB 2.0 Swidge interface IC that combines a PCIe packet switch with a PCIe-to-USB 2.0 bridge. It fans out one PCIe x1 upstream port to two PCIe x1 downstream ports and four USB 2.0 ports, and the device is supplied in a 128-LQFP 14 x 14 mm package. It supports simultaneous access to multiple downstream resources through a single host interface. A Swidge is a multifunctional interface device that consolidates packet-switching and USB bridging functions in one semiconductor. Within the interface IC hierarchy, the PI7C9X442SLBFDE sits between a computer's PCI Express host bus and downstream peripherals. The integrated architecture can simplify board partitioning while providing more expansion options than a conventional single-port PCIe-to-USB controller. The primary feature of this device is its combination of two PCIe x1 downstream ports with four USB 2.0 ports. Its packet-switch function provides ordered connectivity from the upstream PCIe x1 link, while the bridge function provides USB 2.0 host access. This arrangement is useful in embedded systems, notebook computers, industrial controllers, and other platforms that need to expose several PCIe and USB connections through one host interface. The PI7C9X442SLBFDE uses a high-performance interconnect architecture designed for simultaneous downstream access. Because the upstream interface is PCIe x1, total downstream bandwidth is shared by the active links. System designers should therefore account for the aggregate traffic generated by USB traffic and both PCIe x1 downstream paths when validating application performance. Typical uses include compact embedded platforms, notebook computer expansion, multifunction peripheral systems, and USB 2.0 legacy equipment connected to a PCIe host. The 128-LQFP 14 x 14 mm package provides a high pin count for separate power, ground, PCIe, USB, configuration, and auxiliary signals. Exact electrical ratings, clocking requirements, transceiver characteristics, and supported platform features should be confirmed from the manufacturer datasheet before schematic capture. Layout should preserve the differential routing required by the high-speed PCIe and USB interfaces, with impedance-controlled signal paths and continuous return-plane references. Place input and output decoupling capacitors close to their associated supply pins, and follow the datasheet reference layout for the 128-LQFP footprint and exposed-pad or thermal requirements. The use of a 14 x 14 mm LQFP also requires adequate assembly clearance around the perimeter leads. This product overview connects the PI7C9X442SLBFDE's port topology and package requirements with practical selection and layout considerations. It also distinguishes the device from a basic one-port PCIe-to-USB bridge by highlighting the integrated packet-switch function, two PCIe x1 downstream ports, and four USB 2.0 ports.

RFQ צור קשר
PI7C9X442SLBFDEX - PCIe to USB 2.0 Switch | Diodes
PI7C9X442SLBFDEX

PI7C9X442SLBFDEX - PCIe to USB 2.0 Switch | Diodes

The Diodes Incorporated PI7C9X442SLBFDEX is a specialized interface IC combining a PCI Express packet switch with a USB 2.0 host controller in a 128-LQFP package measuring 14 x 14 mm. It supports the transfer of USB 2.0 traffic between a PCI Express system and external USB devices, making it suitable for embedded computing, docking, notebook-computer, and industrial platform designs. A PCI Express-to-USB interface is a specialized bridge controller within the broader hierarchy of interface ICs, PCI and PCIe devices, and semiconductor solutions. Its packet-switch function manages PCI Express traffic while its USB host controller provides connectivity for peripherals that use the USB 2.0 protocol. This integration can reduce the number of separate interface devices required in a compact embedded system. The principal documented features of the PI7C9X442SLBFDEX are its combined PCI Express packet-switch and USB 2.0 host-controller architecture, 128-LQFP surface-mount package, and 14 x 14 mm body size. The product is identified as an active interface component. Its 128-pin package provides the extensive external connections required for multiple lanes, control signals, power rails, and USB host interfaces. Technical architecture centers on two distinct protocol responsibilities within one device. The PCI Express packet switch handles transactions arriving through the PCI Express interface, while the USB 2.0 host controller manages attachment and data transfer for USB devices. This consolidation can simplify system routing compared with separate switch and host-controller devices, although the complete electrical and firmware requirements remain application-specific. Typical applications include notebook-computer accessory interfaces, PCI Express docking systems, embedded industrial controllers, USB expansion platforms, and data-acquisition systems that expose USB peripherals through a PCIe host. The 128-LQFP footprint is intended for multilayer PCB layouts with high-speed routed signals and controlled power distribution. Exact lane, speed, voltage, and timing limits should be confirmed in the manufacturer datasheet before schematic release. Layout and power integrity are critical when deploying this controller. Place decoupling capacitors adjacent to the relevant supply pins, maintain the manufacturer-recommended layer stack and impedance geometry, and route high-speed differential pairs continuously over a solid reference plane. Confirm exposed-pad and thermal-management requirements against the package drawing before finalizing the board outline and assembly process. This product page combines manufacturer-level device positioning, package information, compatibility-focused alternatives, structured comparison data, and practical PCB-design guidance. It helps engineers narrow the interface choice and plan the hardware while keeping all unconfirmed electrical details subject to verification in the manufacturer datasheet.

RFQ צור קשר
PI7C9X752FAE - Dual UART with 64-Byte FIFO | Diodes Inc.
PI7C9X752FAE

PI7C9X752FAE - Dual UART with 64-Byte FIFO | Diodes Inc.

Diodes Incorporated PI7C9X752FAE is a high-performance dual UART interface controller with a 1.62 V to 3.6 V supply-voltage range, a 64-byte FIFO, IrDA 1.1 support, and a 48-pin TQFP package measuring 7 mm by 7 mm. The device combines two independent UART channels with buffered serial-data handling in a surface-mount package suitable for compact embedded communication systems. A UART, or universal asynchronous receiver-transmitter, is a serial interface that converts parallel digital data into framed asynchronous serial signals and reverses that process on reception. Within the interface-controller hierarchy, a UART controller can include FIFO buffering, modem-control signaling, interrupt handling, and IrDA-compatible support. The PI7C9X752FAE is therefore positioned as a multi-channel communications IC rather than a general-purpose logic device or standalone transceiver. The verified defining features are its dual-channel architecture, 1.62 V to 3.6 V operating range, 64-byte FIFO, and IrDA 1.1 capability. A FIFO helps decouple the host processor from temporary variations in serial traffic by buffering received or transmitted characters. The 1.62 V minimum operating voltage also makes the controller suitable for low-voltage embedded systems, provided that the attached processor, transceiver, and external circuitry use compatible logic levels. The PI7C9X752FAE is listed as an RS485 controller, IrDA 1.1, and UART interface device. These functions make it relevant to systems that need multiple asynchronous serial channels, whether for external data acquisition, industrial equipment, infrared data links, or communications between a host controller and peripheral ICs. Because the verified data does not expose the complete register map, clock configuration, electrical timing limits, or pin assignments, those details must be checked in the manufacturer datasheet before final circuit design. Typical implementation places the controller beside one or more external interface devices. One UART channel may connect to an RS-485 transceiver for a longer-distance industrial bus, while the other supports point-to-point serial equipment or an IrDA-compatible peripheral. The controller does not itself replace the physical-layer transceiver for RS-485 or infrared signaling, so appropriate external hardware remains necessary for those links. Designers should confirm logic thresholds, peripheral clocking, interrupt requirements, and the manufacturer-recommended input and output capacitance before layout. Decoupling connections should be short, and the 7 mm by 7 mm TQFP footprint requires careful assembly planning because its 48 leads provide less routing space than a larger package. Signal-routing and grounding practices should also separate the controller's digital interfaces from external transceiver return paths. This page consolidates the verified distributor descriptions, package information, interface functions, and availability evidence for PI7C9X752FAE. It also distinguishes confirmed capabilities from unavailable specifications, helping engineers evaluate the dual-UART controller before requesting the authoritative datasheet and committing the 48-TQFP footprint to a PCB design.

RFQ צור קשר
PI7C9X752FAEX Dual UART with 64-Byte FIFO | Diodes
PI7C9X752FAEX

PI7C9X752FAEX Dual UART with 64-Byte FIFO | Diodes

Diodes Incorporated PI7C9X752FAEX is a high-performance dual UART controller with a 1.62 V to 3.6 V operating supply range, two 64-byte FIFO channels, IrDA 1.1 support, and RS-485 controller functionality in a 48-pin TQFP package measuring 7 mm by 7 mm. The device consolidates two independent UART channels and their receive/transmit buffering within one surface-mount package. A UART, or universal asynchronous receiver/transmitter, is an interface controller that converts parallel data from a processor into serial information and receives serial data in parallel form. Within the hierarchy of interface ICs, a dual UART controller sits between a host processor and external communication equipment. Its FIFO buffers help decouple short data bursts from host interrupts, while IrDA support provides compatibility with infrared communication links and the RS-485 controller function supports balanced differential communication designs. The PI7C9X752FAEX operates from 1.62 V through 3.6 V, making it appropriate for low-voltage embedded systems. Each UART has a 64-byte FIFO according to the device description. The 48-TQFP package provides a substantial pin count for two channels, external interface connections, control signals, and power connections, while its 7 mm by 7 mm body accommodates high-density PCB layouts without using a very large package. The device combines two UART channels in one package, reducing the component count and board area required for dual-port serial communication. A host processor can use the controller for console management, data acquisition, peripheral connectivity, industrial equipment, and embedded control systems. Its low-voltage range is compatible with contemporary 3.3 V digital systems, although systems operating below 1.62 V require suitable level translation or a different interface controller. PI7C9X752FAEX is suited to applications involving two serial ports, including industrial control panels, RS-485 equipment, infrared data links, test systems, and embedded communications modules. When implementing an RS-485 network, the controller's logic interface should be paired with an appropriate external transceiver because the integrated RS-485 controller function does not replace the isolation, drive, and receive functions of a physical transceiver. PCB design should provide a low-impedance ground plane, short supply connections, and decoupling close to the device. Confirm the manufacturer's pin-description table and recommended external-component network before routing the serial signals. Correct signal-level conversion, termination, grounding, and transceiver selection are essential for dependable communication over longer cables or noisy industrial environments. This product summary combines the manufacturer-listed electrical attributes, package information, interface capabilities, and application-oriented design guidance. It also distinguishes the PI7C9X752FAEX from similar UART devices that use a different package or lack equivalent IrDA and RS-485 controller functions, helping engineers assess PCB compatibility before committing to a replacement.

RFQ צור קשר
PI7C9X754FCE - 4 UART with 64-Byte FIFO | Diodes Incorporated
PI7C9X754FCE

PI7C9X754FCE - 4 UART with 64-Byte FIFO | Diodes Incorporated

Diodes Incorporated PI7C9X754FCE is a quad UART interface IC with four independently controlled UART channels, each containing a 64-byte transmit and receive FIFO. It operates from 1.62 V to 3.6 V, includes 5 V tolerant serial inputs, and supports Intel or Motorola data-bus interface selection. The device is packaged in a 64-LQFP 10 x 10 mm package for compact embedded serial-interface designs. A UART, or universal asynchronous receiver-transmitter, is a communication controller that converts parallel data from a host processor into serial data and converts received serial data back into a parallel format. The PI7C9X754FCE belongs to the UART interface IC, interface controller, and clock-and-timing interface hierarchy, providing four channels in one package and reducing board area compared with four discrete UART devices. Key features include a 16C550-compatible register set, independent control of each UART, transmit and receive FIFO level counters, and programmable transmit and receive FIFO trigger levels for interrupt or DMA-driven operation. The 64-byte FIFO buffers help absorb bursts of serial traffic while the host processor is busy, reducing the probability of receiver overrun and improving software flow-control flexibility. The PI7C9X754FCE can be configured for RS485 Controller and IrDA 1.1 use according to distributor product information. The Intel/Motorola bus selection allows compatibility with different processor interfaces, while the programmable FIFO trigger levels support interrupt-driven or DMA-based data movement. These features make the device suitable for multi-channel embedded systems where four UART resources must share limited host I/O. Typical applications include industrial serial hubs, POS terminals, test equipment, printers, modems, multiport communications modules, and embedded control systems. The low 1.62 V to 3.6 V operating range is appropriate for modern 3.3 V digital systems, while 5 V tolerant serial inputs simplify interfaces to legacy equipment. Care is still required when connecting external signals because tolerance applies to the specified serial inputs, not necessarily every control pin. For robust PCB implementation, place the device close to the protected connector or transceiver pins, route serial traces away from clocks and switching-power nodes, and validate input levels, termination, grounding, and system-level RS485 or IrDA requirements. This page combines verified manufacturer and distributor information, pricing references, replacement analysis, and practical design guidance beyond a raw datasheet parameter list.

RFQ צור קשר
PI7C9X754FCEX - 4-Channel UART Controller | Diodes Incorporated
PI7C9X754FCEX

PI7C9X754FCEX - 4-Channel UART Controller | Diodes Incorporated

The Diodes Incorporated PI7C9X754FCEX is a four-channel UART controller with a 1.62 V to 3.6 V core supply range, 64-byte transmit and receive FIFOs, and a 64-LQFP 10 x 10 mm package. It also accepts 5 V-tolerant serial inputs, supports IrDA 1.1 operation, and provides a host interface compatible with Intel or Motorola bus conventions. A UART is a Universal Asynchronous Receiver/Transmitter, a serial-interface controller that converts parallel data from a processor into framed serial transmissions and converts received serial data into parallel data. The PI7C9X754 belongs to the broader hierarchy of interface controllers, communication ICs, and semiconductors. Its four independent channels let one controller manage multiple serial links while sharing a host data bus and interrupt interface. The PI7C9X754FCEX uses 16C550-compatible registers, giving firmware a familiar programming model. Each UART includes 64-byte transmit and receive FIFOs, FIFO level counters, and programmable transmit and receive trigger levels. Those trigger levels support interrupt-driven transfers or DMA operation, reducing the need for the host processor to service every received byte individually. The controller supports both Intel and Motorola data-bus interfaces, allowing it to operate with processors using either timing convention. It also provides automatic wake-up following a sleep mode, making it useful in systems that periodically suspend peripheral activity to reduce power consumption. Its 1.62 V to 3.6 V operating range supports low-voltage embedded systems while the 5 V-tolerant serial inputs broaden interface flexibility. Typical uses include industrial control panels, multiport data acquisition systems, instrument controllers, embedded test equipment, and communications modules requiring several UART channels. The device is particularly suitable when one processor must service multiple RS485, RS232, IrDA, or other serial links while maintaining orderly FIFO flow control and interrupt handling. PCB design should preserve the manufacturer's recommended power and ground layout, place decoupling capacitors close to the supply pins, and provide clean high-speed digital routing. The UART is a digital interface IC rather than a power semiconductor, so thermal operating considerations are centered on supply dissipation and signal integrity rather than a safe operating area graph. This product page organizes the controller's core electrical characteristics, interface functions, application guidance, and practical design considerations into one engineering reference. It also clarifies the distinctions among FIFO behavior, bus compatibility, low-voltage operation, and 5 V-tolerant inputs when evaluating this device for a new multi-channel serial design.

RFQ צור קשר
PI7C9X754FFE - Quad UART with 64-Byte FIFO | Diodes Incorporated
PI7C9X754FFE

PI7C9X754FFE - Quad UART with 64-Byte FIFO | Diodes Incorporated

The Diodes Incorporated PI7C9X754FFE is a quad UART interface IC with four UART channels and a 64-byte FIFO, supplied in an 80-pin LQFP package measuring 12 mm by 12 mm. Its listed interface features include RS485 controller support and IrDA 1.1 compatibility, making it a consolidation-oriented device for systems that need multiple serial communication channels in one package. A UART, or universal asynchronous receiver/transmitter, is a serial interface controller that converts parallel data into framed serial signals and receives framed serial data in parallel form. Within the broader semiconductor hierarchy, a quad UART belongs to the interface IC family, which sits under integrated circuits and supports communication between processors, transceivers, sensors, and peripheral equipment. Four integrated channels can reduce component count and simplify firmware resource allocation compared with separate single-channel UART devices. The PI7C9X754FFE's defining verified features are its four UART channels, 64-byte FIFO buffer, RS485 controller capability, IrDA 1.1 support, and 80-LQFP surface-mount package. The FIFO helps decouple received-byte processing from the serial receiver, reducing the amount of immediate data-handling required by the host processor. This is particularly useful where several ports receive bursts of data or where deterministic interrupt servicing is important. The 80-pin LQFP provides the physical lead count needed for four full-featured UART channels. Pin assignment, logic levels, electrical limits, clock requirements, flow-control features, and exact supported data rates were not included in the verified source snippets and must be confirmed in the manufacturer datasheet before schematic capture or PCB routing. Typical uses include industrial serial concentrators, multi-port instrumentation, embedded control equipment, RS485-connected sensor nodes, and IrDA-capable short-range infrared links. The device is also appropriate for test and measurement systems that expose several asynchronous serial ports through a common controller. Designers should verify pin multiplexing, interrupt topology, peripheral clock requirements, and FIFO behavior in the datasheet before finalizing the PCB. Logic-level compatibility, RS485 transceiver selection, line termination, and isolation must also be confirmed against the external circuitry rather than assumed from the UART controller specification. This page consolidates verified distributor product information, package and feature details, purchasing data, application guidance, and substitution constraints. Because the supplied evidence does not identify a verified pin-to-pin replacement, the alternatives section does not present unverified same-package parts as drop-in options.

RFQ צור קשר
PI7C9X754FFEX - Quad UART Interface IC | Diodes Incorporated
PI7C9X754FFEX

PI7C9X754FFEX - Quad UART Interface IC | Diodes Incorporated

The Diodes Incorporated PI7C9X754FFEX is a quad UART interface IC with four UART channels and a 64-byte FIFO in an 80-LQFP (12 x 12 mm) package. The device is identified in distributor listings as an RS485 controller with IrDA 1.1 support, providing a consolidated interface solution for systems that require multiple serial communication channels. A UART interface IC is a semiconductor device that converts parallel digital data into serial signals and receives serial data in parallel form. It belongs to the interface IC hierarchy, which also includes RS485 controllers, IrDA transceivers, and other communication adapters. The PI7C9X754FFEX combines four UART functions in one package, reducing the number of separate serial-interface devices required in embedded equipment. The main documented features include a quad-UART configuration, a 64-byte FIFO per channel according to the product listing, RS485 controller functionality, and IrDA 1.1 support. These features make the device relevant to industrial control, instrumentation, embedded communications, and multi-channel data-acquisition systems where several serial ports must operate within one design. The 80-LQFP (12 x 12 mm) package provides a defined lead arrangement for compact but high-pin-count PCB designs. Because the device integrates four UART channels, board-level design requires careful review of each channel's data, control, interrupt, and supply connections. The manufacturer datasheet should be used to assign the complete pinout, power requirements, timing values, and electrical limits before PCB routing. Typical uses include industrial controllers with multiple serial-device connections, test equipment communicating with several instruments, data-acquisition gateways, and embedded systems that bridge host processors to RS485 or IrDA peripherals. In each case, the integrated FIFO can help buffer serial traffic, while the quad-channel architecture reduces component count compared with four separate UART interface devices. Designers should confirm signal levels, transceiver requirements, interrupt allocation, and package land pattern in the manufacturer datasheet. RS485 applications may require external line drivers or transceivers because the PI7C9X754FFEX is identified as an RS485 controller rather than a complete isolated RS485 transceiver. This page summarizes the available product information and provides engineering guidance for evaluating the device in a new design. This product page consolidates the confirmed PI7C9X754FFEX features, package information, sourcing links, application guidance, and the key qualification checks engineers need when comparing multi-channel UART interface ICs.

RFQ צור קשר