PI7C9X1172CZHEX - 33Mbps I2C/SPI to UART Bridge | Diodes
MPN: PI7C9X1172CZHEX ✓ פעילPI7C9X1172CZHEX סקירה
An I2C/SPI-to-UART bridge controller is a type of interface IC that translates between a host serial bus and independent UART channels. It sits between a microcontroller or processor and an embedded serial subsystem, allowing one host bus to connect to multiple UART peripherals while reducing the number of host I/O pins required. In the broader hierarchy, the device belongs to the interface-controller family within integrated circuits and embedded communication semiconductors.
Key features include a maximum UART data rate of 33 Mbps, support for I2C Standard-mode and Fast-mode operation, dual UART channels, and as many as eight additional programmable GPIO pins. The 32-pin TQFN package also supports compact board layouts in industrial controls, communications equipment, embedded systems, and test systems where several serial functions must share a limited connector or routing area.
The PI7C9X1172 family combines an I2C host interface, SPI support, UART framing, and programmable parallel I/O in one controller. The I2C interface uses the standard SDA and SCL lines, while the UART side provides two channels capable of high-speed serial transfer. Low operating and sleeping current are stated design goals, making power-conscious control of the serial subsystem possible when the system is not actively exchanging data.
Typical uses include industrial serial gateways, programmable logic and test equipment, embedded control boards, peripheral expansion, and compact communications modules. The dual-channel architecture is especially useful when an embedded controller must monitor or control two independent UART-linked subsystems through one I2C or SPI host connection.
Board design should keep I2C traces short, provide the pull-up network required by the selected bus speed, and route UART signals with return-path discipline. Because this version uses a 32-pin TQFN package, verify the exposed-pad connection, land pattern, and thermal strategy against the manufacturer pin-description and package drawings before layout release.
This page organizes the controller’s interface capabilities, package constraints, application guidance, comparison data, and sourcing options into a practical engineering reference that supports both initial component selection and PCB implementation.
חלופות תחליף ישיר עבור PI7C9X1172CZHEX — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותPI7C9X1172CZHEX דירוגים מרביים ומאפיינים חשמליים
| Device Type | Dual-channel I2C/SPI-to-UART bridge controller |
| Maximum UART Data Rate | 33 Mbps |
| UART Channels | 2 channels |
| Host Serial Interfaces | I2C-bus and SPI |
| I2C Modes Supported | Standard-mode and Fast-mode |
| I2C Bus Lines | 2 lines: SDA and SCL |
| Programmable GPIO Count | Up to 8 pins |
| מארז | 32-pin TQFN, 5 mm x 5 mm |
| Family Package Options | QFN-32 and TSSOP-28 |
| סוג הרכבה | Surface mount |
| סטטוס RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
מדריך תצורת פינים של PI7C9X1172CZHEX qfn-32 and tssop-28
תצורת פינים עבור PI7C9X1172CZHEX (מארזת qfn-32 and tssop-28). רכיב הספק זה כולל מסופי שער, ניקוז ומקור. במארזים לא מקוטבים, יש לעיין בגיליון הנתונים של היצרן לכיוון מדויק של פין 1 ולפרטי טביעת רגל. יישומים נפוצים כוללים תכנון ספקי כוח, הנעת מנועים והחלפת עומסים.
אין נתוני פריסת פינים מפורטים עבור PI7C9X1172CZHEX.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
PI7C9X1172CZHEX מתאים עבור 6 יישוםs: Industrial Serial Gateway, Embedded Peripheral Expansion, Programmable Test Equipment, Communications Module, Data Acquisition Controller, Multi-Function Control Board.
Industrial Serial Gateway
The PI7C9X1172CZHEX fits a compact industrial gateway that connects one host processor to two external serial subsystems. A host can manage both UART channels through I2C or SPI while the controller handles UART framing at rates up to 33 Mbps. This architecture reduces the number of host pins required for dual-channel communications and leaves up to eight GPIO pins available for modem-control, reset, interrupt, or status signals. The principal design consideration is ensuring that the gateway’s supply, temperature, grounding, and surge requirements remain within the device’s electrical limits.
מומלץ
Embedded Peripheral Expansion
PI7C9X1172CZHEX can expand a microcontroller with two UART channels without dedicating multiple direct serial pins to the host. The I2C-bus connection uses SDA and SCL, while SPI provides an alternative host interface for systems that already operate in SPI mode. With UART operation reaching 33 Mbps and as many as eight programmable GPIO pins, the device can consolidate several peripheral-control functions into one interface IC. Firmware must correctly initialize the bridge, configure each UART, map interrupts or GPIO events, and maintain deterministic command and response handling.
מומלץ
Programmable Test Equipment
The PI7C9X1172CZHEX is useful in automated test equipment that must connect a controller to two independent serial instruments. I2C or SPI provides a compact connection to the test controller, while dual UART channels handle higher-speed instrument traffic and protocol-specific exchanges. The available GPIO pins can support triggers, interlocks, resets, or status indicators. Because test systems often mix RS-232, RS-422, and TTL signaling, engineers should determine whether the UART-side levels can be used directly or whether external line drivers and protection are required.
מומלץ
Communications Module
PI7C9X1172CZHEX can organize a compact communications module around one host-side I2C or SPI link and two high-performance UART outputs. The 33 Mbps maximum UART rate supports demanding data paths, while programmable GPIO signals can provide modem-control or equipment-state functions. The 5 mm by 5 mm TQFN-32 package saves board area compared with larger multi-channel interface solutions. Layout should preserve controlled return paths for the high-speed UART signals, provide suitable I2C pull-ups, and keep the exposed-pad connection compliant with the manufacturer package instructions.
מומלץ
Data Acquisition Controller
The PI7C9X1172CZHEX can bridge a data-acquisition controller to two serial instruments or sensor subsystems through its I2C-bus or SPI host side. Dual UART channels permit concurrent command traffic and measurement data transfer, while the GPIO outputs can trigger acquisition equipment or monitor ready signals. Its support for Standard-mode and Fast-mode I2C operation makes it adaptable to embedded control architectures. System designers should calculate bus loading, avoid long unprotected I2C branches, and verify UART baud-rate tolerance across temperature and clock tolerances.
מומלץ
Multi-Function Control Board
PI7C9X1172CZHEX suits a control board that needs several serial functions but has limited processor I/O. Two UART channels can connect motor controllers, display peripherals, or service interfaces, while I2C or SPI maintains communication with the main processor and up to eight GPIO pins handle discrete control tasks. This consolidation can simplify firmware and reduce routing congestion in a 5 mm by 5 mm footprint. Designers should reserve the correct QFN-32 land pattern, validate all voltage-domain connections, and include appropriate pull-up, decoupling, and protection components.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PI7C9X1172CZHEX — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Device Type | Dual-channel I2C/SPI-to-UART bridge controller |
| Package | 32-pin TQFN, 5 mm x 5 mm |
| Brand | Diodes Incorporated |
| Maximum UART Data Rate | 33 Mbps |
| UART Channels | 2 channels |
| Host Interface | I2C-bus and SPI |
| Programmable GPIO | Up to 8 pins |
| I2C Support | Standard-mode and Fast-mode |
| Family Package Options | QFN-32 and TSSOP-28 |
| Mounting Type | Surface mount |
מבדילים עיקריים
- Consolidates a host serial bus, dual UART channels, and programmable GPIO (לעומתMAX3221IPWR)
- Higher stated UART throughput (לעומתSP3232EHEY-L)
- Space-efficient QFN implementation (לעומתMAX3221IPWR)
הערות תכנון
Route the I2C SDA and SCL lines as a compact, matched pair and place their pull-up resistors close to the bus master or designated end point. The device supports Standard-mode and Fast-mode operation, but the usable frequency still depends on bus capacitance, pull-up strength, clock stretching, and the electrical characteristics of every connected device. Avoid adding unnecessary stubs to the serial bus.
Use the manufacturer QFN-32 land pattern and package drawing before releasing the PCB. Confirm whether the exposed pad is electrically designated as ground or otherwise connected, follow the stated thermal-pad soldering guidance, and place the required interface components near their associated pins. Incorrect exposed-pad treatment can affect assembly, heat transfer, and system reliability.
Treat UART connections as high-speed communication links even though they are asynchronous. Route signals over a continuous reference plane, minimize stub lengths and vias, and maintain a nearby return path. Validate timing and voltage levels with the connected UART transceiver, especially when operating near the stated 33 Mbps maximum rate or when long cables are present.
Do not assume that an I2C/SPI-to-UART bridge can replace a dedicated RS-232 transceiver. The bridge manages serial protocol conversion through the host, while a transceiver performs physical-level conversion. Confirm that each UART endpoint uses compatible voltage levels, and add a suitable line driver or receiver when the required electrical interface is RS-232, RS-422, or another physical standard.
מידע על תאימות
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this ordering code. Review the current manufacturer product documentation before using the device in regulated or automotive equipment.