מוצרים (44,000+)

THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI
THVD1552DR

THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI

The Texas Instruments THVD1552DR is a 5-V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC (D) package, integrating ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It supports a signaling rate up to 50 Mbps and operates across a wide 3 V to 5.5 V supply range, making it a robust interface for industrial and noisy environments where reliable differential communication is required. An RS-485 transceiver is a physical-layer (PHY) device that converts a single-ended UART/logic signal into a differential signal suitable for transmission over twisted-pair cabling while meeting the TIA/EIA-485 standard. This PHY sits within the broader OSI stack between the controller UART (data-link layer) and the physical medium (cable), under the family name of serial-interface ICs. The THVD1552 belongs to the THVD15xx sub-family of noise-immune TI transceivers, sharing pinouts and feature sets across half- and full-duplex variants. Key features include ±18-kV IEC 61000-4-2 contact/air-discharge ESD protection directly on bus pins (driver output and receiver input), ±4-kV IEC 61000-4-4 EFT immunity, an internal fail-safe biasing on the receiver output for open/short bus conditions, 1/8 unit-load support (up to 256 nodes on a single bus), and a wide -40 °C to +125 °C operating temperature range. The 14-SOIC footprint is industry standard for this class and supports reflow-solder assembly. The THVD1552 uses a CMOS process with integrated TVS-style ESD structures on the bus pins; this allows designers to replace external protection components, BOM cost, and PCB area. Internal fail-safe circuitry guarantees a logic-high receiver output when the bus is idle, shorted, or terminated but undriven — critical for deterministic polling protocols such as Modbus. Typical applications include motor-control feedback links, multi-drop industrial sensor buses, building automation nodes (BACnet/MS-TP, Modbus RTU), solar inverter inter-module communication, and any 3.3-V or 5-V MCU UART-to-RS-485 bridge requiring strong system-level ESD/EFT robustness. When laying out this part, place the bus-side 120 Ω termination as close to the IC bus pins as possible, route the differential pair A/B symmetrically, and keep the bus stub length under one-tenth of the signal rise time (about 30 mm at 50 Mbps) to preserve signal integrity. This page consolidates distributor stock/pricing, drop-in alternative listings, and PCB design notes not found in the TI datasheet alone, accelerating engineer selection for noise-immune RS-485 designs.

RFQ צור קשר
TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI
TIBPAL16R8-25CFN

TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI

The Texas Instruments TIBPAL16R8-25CFN is a high-performance, low-power IMPACT-X PAL (Programmable Array Logic) device from Texas Instruments, delivering 25 ns maximum propagation delay and an 8-macrocell registered architecture in a 20-pin PLCC (9x9 mm) J-leaded package. The device combines Advanced Low-Power Schottky (ALS) technology with titanium-tungsten (Ti-W) fuses, providing 64 product terms, eight D-type registered outputs, and a typical operating frequency of 30 MHz at 5.25 V supply. A PAL (Programmable Array Logic) device is a one-time-programmable (OTP) SPLD that implements custom combinational and registered logic functions through a programmable AND-OR array, preceded by fixed OR gates and fed by user-defined product-term equations. Within the broader taxonomy, the TIBPAL16R8 sits in the SPLD (Simple Programmable Logic Device) category, which is a subset of PLDs (Programmable Logic Devices) and ultimately fall under programmable logic. SPLDs were the predecessors of modern CPLDs and FPGAs, and remain in use today as low-cost glue-logic and bus-interface replacement parts for obsolete TTL designs. Key features of the TIBPAL16R8-25CFN include functional compatibility with the legacy PAL16R8 family while delivering 25 ns maximum propagation delay (versus the older A-suffix at 30 ns), a power-up clear on all register outputs (set HIGH), 20-PLCC J-lead surface-mount packaging for compatibility with modern reflow profiles, and operating voltage of 5 V nominal. Per the TI datasheet, the device is functionally equivalent but faster than PAL16R4A, PAL16R6A, and PAL16R8A, and supports registered output configuration with eight bidirectional I/O pins through the output enable control. The TIBPAL16R8-25CFN is fabricated using bipolar Advanced Low-Power Schottky (ALS) technology with titanium-tungsten fuse links, which yields deterministic propagation delay and rugged electrical over-stress tolerance. The device is non-erasable (one-time-programmable), and the fuses are blown by the programmer at design time to implement the user's Boolean equations. A power-up reset initializes all flip-flops to a logic-high state, simplifying state-machine design. Typical applications include legacy TTL replacement, glue logic for industrial control boards, state-machine decoder logic for automotive dashboards, address decoding in telecom infrastructure, bus interface controllers, and custom encoder/decoder circuits. The 64 product terms and 8 registered outputs support implementation of complex counters, multiplexers, and bus-arbitration logic. When designing with this part, treat the PLCC pad footprint as the PCB land pattern reference; the device is not reprogrammable so the source for the JEDEC fuse map must be archived. Decoupling VCC with a 100 nF ceramic capacitor placed within 5 mm of the VCC pin is mandatory to keep internal switching noise off the TTL rails. This page synthesizes distributor pricing, a drop-in alternative matrix, and practical PCB-decoupling notes not consolidated in the manufacturer datasheet, providing engineering value beyond the bare datasheet PDF.

RFQ צור קשר
TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments
TIC10024QDCPRQ1

TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments

The Texas Instruments TIC10024QDCPRQ1 is an automotive-grade 35-V Multiple Switch Detection Interface (MSDI) with SPI, housed in a 38-pin HTSSOP package with exposed thermal pad (DCP). It monitors 24 direct switch inputs (10 configurable for ground- or supply-referenced switches), integrates adjustable wetting current sources per channel, and reports switch state through an SPI-compatible serial port — eliminating up to 24 discrete comparator/MCU GPIOs in a BCM (Body Control Module). A Multiple Switch Detection Interface (MSDI) is a mixed-signal ASSP that bridges mechanical switches (e.g. rocker switches, momentary buttons, limit switches) to a microcontroller in 12-V automotive electrical systems. It belongs to the broader hierarchy: switch interface IC → interface IC → signal conditioning IC → power management / body electronics ASSP → automotive semiconductor. The MSDI provides per-input wetting current to prevent contact oxidation, programmable threshold comparators for switch-closed detection, and serial aggregation of 24 inputs into a few SPI pins — reducing wire harness complexity and MCU pin count. Key features include 35-V absolute maximum load-dump tolerance (12-V nominal), adjustable wetting current per channel, selectable ground- or supply-referenced inputs on 10 channels, integrated input debounce / de-glitch filters, configurable interrupt generation for wake events, low quiescent current sleep mode, and SPI communication up to [DATA_NEEDED: SPI clock rate]. The device operates across -40 °C to +125 °C ambient (AEC-Q100 Grade 1) and includes thermal shutdown protection. The exposed-pad HTSSOP-38 package provides theta_JA suitable for BCM thermal environments. Technically, the TIC10024-Q1 uses a per-channel comparator architecture with current-mode wetting sources driven from a shared internal regulator. The SPI peripheral implements a standard mode-0 protocol with a frame-format error flag and a global wake-up interrupt output. Internal state machine handles input filtering, hysteresis, and wetting-current modulation; channel configuration registers enable per-input current programming and pull-up/pull-down selection. Typical applications include automotive body control modules (BCM) reading 24 switches per chip, gateway/zonal controllers monitoring door/trunk/hood latches, steering-wheel switch matrices, seat-control switch aggregation, and overhead-console button clusters. The 24-input density lets a single MSDI replace multiple 8-/16-channel general-purpose I/O expanders. When designing with this part, ensure the PCB layout accommodates the exposed thermal pad with at least 4 thermal vias to the inner ground plane for AEC-Q100 thermal conformance. The 38-pin HTSSOP package requires careful routing of SPI traces; keep the SCLK/MOSI/MISO bundle length-matched and routed away from VBAT-switching nodes. This page synthesizes distributor pricing (as of 2026-10-11), drop-in same-package alternatives, and practical AEC-Q100 design notes — information not consolidated in the TI datasheet alone.

RFQ צור קשר
TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP
TIR1000IPWR

TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP

The Texas Instruments TIR1000IPWR is a standalone IrDA (Infrared Data Association) SIR (Serial Infrared) encoder/decoder IC housed in an 8-pin TSSOP (PW) package and rated for the -40C to +85C industrial temperature range. It encodes and decodes asynchronous UART bit streams into IrDA-compliant 3/16 pulse-modulated optical signals at data rates from 1200 bps up to 115.2 kbps, and operates from a 2.7 V to 5.5 V supply. The TIR1000IPWR is the tape-and-reel (R) packaging variant of the TIR1000IPW die, which is functionally identical to the legacy TIR1000IPWRG4. An IrDA encoder/decoder is a specialized interface IC that sits between a host microcontroller's UART and an external infrared transceiver (typically a PIN photodiode + LED pair). It performs the bit-stuffing and pulse-width modulation required by the IrDA physical layer so the host CPU only sees a transparent serial stream; the broader category belongs to interface ICs in the connectivity hierarchy (interface IC > transceiver > encoder/decoder). Key features include 1200-bps to 115.2-kbps IrDA 1.0 / HPSIR compliance, single 2.7 V to 5.5 V supply, direct UART handshake interface, low-power shutdown mode, and CMOS construction. The TIR1000IPWR adds an infrared port to any standard UART, eliminating the need for bit-banging IR protocols in firmware and offloading real-time pulse-width timing from the host MCU. The architecture uses a baud-rate generator derived from an external 16x clock (typically the UART's reference), a transmit pulse shaper that converts the UART TX bit stream into 3/16-width IR pulses, and a receive decoder that recovers the UART RX stream from the demodulated IR input. Because it is a pure logic encoder (no onboard LED driver), the host must add a discrete IR transceiver module (e.g., a TFDU4100 / HSDL-3201 class device) to drive the optical front end. Typical applications include IrDA ports on PDAs, industrial handhelds, medical data terminals, point-of-sale (POS) equipment, and consumer electronics printers. The wide supply range and 8-pin TSSOP package make it suitable for space-constrained designs that need to retrofit IrDA onto an existing UART. A key design consideration is clock sourcing. The TIR1000IPWR requires a 16x baud-rate reference clock (XCLK), which is normally derived from the host UART's baud-rate generator; if the host baud rate changes, XCLK must be reprogrammed accordingly. The IC does not include the optical transceiver, so a separate IrDA transceiver module must be added externally. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for IrDA encoder/decoder selection.

RFQ צור קשר
TJA1020T/N1 - LIN Transceiver, 8-SO | NXP Semiconductors
TJA1020T/N1

TJA1020T/N1 - LIN Transceiver, 8-SO | NXP Semiconductors

The NXP Semiconductors TJA1020T/N1 is a single LIN-bus transceiver integrated circuit packaged in an 8-pin SO package. It provides the physical-layer interface between a LIN network and a host microcontroller, converting serial data into the LIN bus signal and delivering received bus data through the RXD output. The TJA1020T/N1 is listed as a half LINbus transceiver, indicating its role as a node interface for LIN communication networks. A LIN transceiver is a mixed-signal interface device within the broader hierarchy of interface ICs, communication transceivers, and semiconductors. LIN, or Local Interconnect Network, is used for low-cost distributed control in vehicle and industrial networks. The transceiver provides the physical signaling layer between a microcontroller's serial interface and the wired LIN bus, while protocol handling, diagnostics, and higher-layer message handling remain the responsibility of the host controller. The principal product-specific features visible in the manufacturer and distributor documentation are the 8-pin SO package, LIN transceiver function, half-LINbus node role, RXD receive path, TXD transmit input, LIN bus connection, internal bus-output pull-up arrangement, and support for leader-side implementation using external components. The manufacturer describes the LIN output as being pulled high through an internal termination resistor, while a leader design can add a resistor-and-diode network between the LIN pin and a supply-related pin. Operationally, the transmit input accepts the controller's serial waveform and the device converts it into a LIN-compatible bus waveform. In the receive direction, the receiver detects the LIN bus input and transfers the recovered data to the host through RXD. The interface therefore isolates the controller from direct physical signaling while supporting bidirectional communication over a single LIN conductor relative to the vehicle ground reference. Typical uses include LIN-controlled automotive sub-networks, body electronics modules, seat and door modules, climate-control peripherals, sensor interfaces, actuator controllers, and industrial distributed-control nodes. The part is especially relevant when an existing microcontroller already implements the LIN protocol and requires a dedicated physical-layer transceiver. Its 8-pin SO package also supports compact, conventional PCB layouts where an 8-pin surface-mount footprint is available. Design attention should center on the LIN bus network, grounding, transceiver supply arrangement, and the distinction between follower and leader implementations. Follower nodes use the internal pull-up behavior described by NXP, whereas leader nodes require the appropriate external resistor and diode network. PCB traces should preserve a short, direct path to the LIN connector and maintain a continuous ground reference. The manufacturer product page should be consulted for the exact application circuit, recommended external components, and supply requirements. This page consolidates the exact package and lifecycle information, source datasheet links, interface-focused design guidance, and documented substitution information for engineers evaluating the TJA1020T/N1. Because the manufacturer marks the product as end-of-life, engineers should also plan a migration path or confirm availability through the Request a Quote form before committing to a new production design.

RFQ צור קשר
TJA1020T/VM - LIN Transceiver, 8-SO | NXP Semiconductors
TJA1020T/VM

TJA1020T/VM - LIN Transceiver, 8-SO | NXP Semiconductors

The NXP Semiconductors TJA1020T/VM is a single-channel LIN bus transceiver packaged in an 8-pin small-outline package. It integrates the physical-layer functions required to connect a low-speed serial network node, and its designated half LINbus interface supports communication between a LIN master and peripheral nodes. The device is offered as TJA1020T/VM,112 and is identified by NXP as no longer manufactured. A LIN transceiver is an interface integrated circuit that converts logic-level controller signals into the voltage waveform used on a LIN bus and converts received bus activity back into logic-level information. It belongs to the broader hierarchy of interface IC, bus transceiver, physical-layer transceiver, and semiconductor. LIN, or Local Interconnect Network, is commonly used for distributed vehicle functions and other cost-sensitive serial networks where a single-wire bus is advantageous. The TJA1020T/VM includes sleep mode as its default state after power-up. According to the manufacturer datasheet, the transceiver can be awakened remotely through the LIN pin, woken locally through the NWAKE pin, or activated directly through the NSLP pin. These three wake paths support designs in which a network node must remain low-power while still detecting an external wake request. The manufacturer datasheet also describes input filtering for the LIN, NWAKE, and NSLP pins. These filters help prevent unwanted transitions from disturbing the sleep and wake decision process, an important consideration when connecting a transceiver to vehicle wiring that can experience electrical transients and long unpowered periods. The 8-SO package also keeps the PCB footprint compact for distributed electronic control units and compact peripheral nodes. Typical uses include LIN master or peripheral nodes in automotive body systems, seat and door modules, lighting controllers, climate-control peripherals, sensor interfaces, and low-cost embedded serial networks. The sleep-first operating behavior is particularly useful in battery-powered or intermittently connected equipment where standby consumption and predictable wake-up behavior are central design requirements. Designers should use the manufacturer pin-description table and application information when assigning the LIN, supply, ground, NWAKE, and NSLP connections. Because this part is no longer manufactured, an existing design should be reviewed against the latest NXP product lifecycle information before new production commitments are made. This page brings together the device status, manufacturer documentation links, verified interface features, related drop-in candidates, and practical implementation guidance. It also distinguishes documented behavior from parameters that require confirmation in the current manufacturer datasheet.

RFQ צור קשר
TJA1021T/20/C - LIN 2.1 Transceiver, 20kBd, 8-SO | NXP
TJA1021T/20/C

TJA1021T/20/C - LIN 2.1 Transceiver, 20kBd, 8-SO | NXP

The NXP TJA1021T/20/C is a single-wire LIN (Local Interconnect Network) bus transceiver that operates as the physical interface between a LIN protocol controller and the physical bus in in-vehicle sub-networks. The /20 variant supports baud rates from 1 kBd up to 20 kBd and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016. It is housed in an 8-pin SO (SOIC-8) surface-mount package and is pin-to-pin compatible with the legacy TJA1020 and NXP MC33662(B) LIN transceivers. What is a LIN transceiver? A LIN transceiver is a physical-layer (PHY) device that translates the low-voltage digital logic signals (TXD/RXD) generated by a microcontroller or LIN controller into the single-wire, dominant/recessive, slew-rate-controlled bus waveform defined by the LIN standard. It handles bus fault protection (short to battery, short to ground, load-dump), ESD protection, thermal shutdown, and wake-up detection via the bus line. The LIN protocol is widely used as a low-cost sub-bus for non-critical automotive body electronics (mirror controls, seat adjusters, door modules, roof consoles), where CAN would be over-spec. Key features of the TJA1021T/20/C include an integrated slew-rate-controlled LIN bus driver that meets the LIN 2.1/SAE J2602 wave-shaping requirements with minimized electromagnetic emissions (EME), improved ESD robustness compared to the TJA1020, a -27 V to +40 V wide bus load-dump protection range, low-power sleep mode with remote wake-up via the LIN pin, and a dedicated TXD dominant time-out to prevent the bus from being permanently driven. Architecturally, the TJA1021T/20/C uses a bipolar high-voltage process for the bus-side driver stage combined with low-voltage CMOS logic on the protocol-side (TXD, RXD, EN, WAKE). The integrated pull-up resistor on the bus line and the internal slope-control feedback loop produce the trapezoidal LIN waveform specified by SAE J2602, eliminating the need for an external diode or waveform-shaping RC network. Built-in fail-safe features include loss-of-bat handling, ground-shift tolerance, and under-voltage reset on VCC. Typical applications include automotive body-control modules, LIN slaves for door/window/seat/steering-column control, HVAC flap motors, mirror adjusters, ambient lighting nodes, and rain/light sensors. Because the part is qualified to the AEC-Q100 automotive reliability standard, it is designed for the harsh electrical environment of a 12 V automotive battery rail, including jump-start and load-dump transients. It also suits industrial LIN sub-buses where the LIN standard provides a simple, robust single-wire alternative to CAN or RS-485. When designing with this device, ensure the master resistor (typically 660 ohms pull-up to VSUP through a diode) and the bus capacitor (typically 220 pF to 1 nF) are correctly sized, and that the LIN node wake-up strategy (local wake via the WAKE pin vs remote wake via the bus) matches the application requirements.

RFQ צור קשר
TJA1022HGZ - Dual LIN 2.2A/SAE J2602 Transceiver DHVQFN-24 | NXP
TJA1022HGZ

TJA1022HGZ - Dual LIN 2.2A/SAE J2602 Transceiver DHVQFN-24 | NXP

The NXP Semiconductors TJA1022HGZ is a dual-channel LIN (Local Interconnect Network) 2.2A/SAE J2602 transceiver in a 24-pin DHVQFN (5.5 x 3.5 mm) exposed-pad package. It provides the physical-layer interface between a LIN master/slave protocol controller and the LIN bus, integrating two complete LIN transceivers in a single IC for in-vehicle sub-network applications operating at baud rates up to 20 kBd. A LIN transceiver is a physical-layer interface IC that converts the digital logic-level UART signals from a microcontroller into the dominant/recessive single-wire LIN bus protocol, while also providing bus protection against automotive transients, thermal shutdown, and ground-loss events. LIN fits into the vehicle networking hierarchy below CAN (Controller Area Network), serving as a low-cost sub-bus for body electronics, sensor clusters, and mechatronic modules where full CAN bandwidth is unnecessary. Key features include LIN 2.0/2.1/2.2/2.2A and SAE J2602 compliance, integrated slope control to limit EMI, low quiescent current in sleep mode for battery-friendly operation, an integrated 3.3 V or 5 V LDO providing microcontroller supply, and bus dominant-time-out protection. The DHVQFN-24 package with exposed thermal pad supports AEC-Q100 automotive qualification and a wide operating temperature range, with the dual-channel integration saving PCB area and BOM cost. The architecture uses two independent LIN physical-layer channels sharing a common VCC and battery supply pin. Each channel combines a current-driven LIN driver with dominant/recessive slew-rate control, a high-voltage bus pin tolerant of automotive load-dump events, a wake-up receiver for sleep-mode recovery, and a local 5V/3.3V LDO that can power a host microcontroller. Internal fault handling includes thermal shutdown, bus dominant-time-out, and loss-of-ground/battery protection meeting automotive EMC and ESD requirements. Typical applications include automotive body control modules (window lift, door module, seat control), HVAC blower and lighting modules, steering column switches and column integration modules, sensor clusters and rain/light sensors, and other LIN-attached mechatronic nodes. Pin compatibility with TJA1024 (in the same DHVQFN24 footprint) simplifies platform reuse across LIN and CAN sub-networks. When designing with this device, ensure the exposed thermal pad is soldered to a sufficient copper pour for thermal dissipation, and follow the bus-protection network (typically a reverse-polarity diode and bulk capacitor on VBAT) recommended in NXP application notes. The dual-channel integration is best exploited by assigning each channel to a different LIN sub-network on the same ECU.

RFQ צור קשר
TJA1022TK - Dual LIN 2.2A Transceiver HVSON14 | NXP
TJA1022TK

TJA1022TK - Dual LIN 2.2A Transceiver HVSON14 | NXP

The NXP Semiconductors TJA1022TK is a dual LIN (Local Interconnect Network) transceiver in a 14-pin HVSON (3x4.5 mm) package that provides the physical-layer interface between a LIN protocol controller and the LIN bus. It supports baud rates up to 20 kBd and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602, making it suitable for in-vehicle subnetwork applications. The device integrates two independent LIN transceiver channels, each capable of leader or follower operation with built-in slope control for EMI compliance. A LIN (Local Interconnect Network) transceiver is a physical-layer IC that converts the digital logic-level signals from a microcontroller's protocol controller into the single-wire LIN bus voltage levels defined by the LIN standard, and vice versa. LIN sits below CAN in the automotive networking hierarchy (sub-bus: LIN -> sub-bus of CAN -> in-vehicle network), enabling low-cost communication for body electronics such as door modules, seat controllers, mirror adjusters, and roof consoles. The TJA1022's dual-channel integration halves the cell density on the PCB versus two discrete transceivers. Key features include an operating supply voltage range typically suitable for 12 V automotive systems, integrated LIN bus termination, thermal shutdown protection, bus pin transient protection per ISO 7637, and very low quiescent current in sleep mode for battery-friendly standby. The device supports both normal and silent-mode operation for selective wake-up scenarios. Per the NXP datasheet, the TJA1022T and TJA1022TK are pin-compatible with the legacy TJA1020, TJA1021, TJA1027, and TJA1029 single LIN transceivers in SO14 / HVSON14 packages. The TJA1022TK architecture combines two independent LIN physical-layer blocks sharing common supply and ground pins. Each channel includes a wave-shaping driver with controlled slew rate to meet LIN EMC requirements, a dominant-timer for bus lock-up protection, and a wake-up receiver. The HVSON14 exposed pad provides a low thermal resistance path, essential for engine-bay and under-hood modules where ambient temperatures can reach 125 C. Typical applications include automotive body-electronics modules (door, seat, mirror, roof), HVAC control panels, steering-wheel button interfaces, LED lighting controllers, and powertrain sensors connected to a body-domain LIN sub-bus. The dual-channel integration is especially valuable in door-modules and seat-modules where multiple LIN sub-nets reduce harness weight and BOM cost. When designing with this part, follow NXP's reference layout guidance: place the HVSON14 exposed pad on a continuous ground copper pour with multiple thermal vias, keep the LIN bus traces short, and add the recommended external reverse-battery and ESD protection on the LIN pins if the module is exposed to handling transients. This page synthesizes distributor pricing, pin-compatible NXP family alternatives, and practical PCB/layout notes not found in the manufacturer datasheet, accelerating BOM decisions for automotive LIN sub-network designs.

RFQ צור קשר
TJA1024HG - Quad LIN 2.2A/SAE J2602 Transceiver | NXP
TJA1024HG

TJA1024HG - Quad LIN 2.2A/SAE J2602 Transceiver | NXP

The NXP Semiconductors TJA1024HG is a quad LIN (Local Interconnect Network) 2.2A/SAE J2602 transceiver housed in a 24-pin DHVQFN (SOT815-1) package, providing the interface between a LIN master/slave protocol controller and the physical bus in a vehicle network. It comprises two independent and separated dual LIN transceiver channels, supports baud rates up to 20 kBd, and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 standards. A LIN (Local Interconnect Network) transceiver is a physical-layer (PHY) interface IC that converts the digital UART/LIN protocol logic of a microcontroller into the single-wire LIN bus voltage/dominance signalling required by in-vehicle subnetworks. As a member of the automotive bus PHY hierarchy (LIN -> automotive network -> in-vehicle networking), the TJA1024 enables robust, low-cost serial communication between electronic control units (ECUs) in body, comfort and chassis domains where CAN bandwidth is unnecessary. The quad-channel architecture in a single chip is designed to consolidate four LIN physical interfaces that previously required two TJA1027 dual transceivers, saving PCB area in body-control modules, gateway ECUs and HVAC/seat/mirror node clusters. Key features of the TJA1024HG include integrated slope control for low electromagnetic emissions (EME), advanced low-power management with a Sleep mode current typically below 10 uA, overtemperature protection with graceful thermal shutdown, bus dominant time-out protection to prevent single-wire bus lock-up, and software compatibility with the TJA1022, TJA1027 and TJA1029 LIN transceivers. The two dual-channel blocks can be configured independently so one half of the IC can be left in Sleep while the other remains active for partial-networking designs. The TJA1024HG uses a bipolar/BiCMOS output stage that delivers up to 2.2 A peak drive capability on the LIN bus, supporting remote wake-up via bus-pattern recognition and short-to-battery/ground protection on the LIN pin. Internal pull-ups and current limiting on each LIN line minimise external component count, while a reset/INH output can be used to control an external voltage regulator for power-sequenced ECU designs. Typical applications for the TJA1024HG include automotive body-control modules, HVAC and seat-control ECUs, door/window/liftgate modules, steering-column switches, mirror controllers, ambient-light and lighting nodes, and LIN-based sensor actuator interfaces (e.g. smart MOSFET pre-drivers, rain/light sensors). Its 24-pin DHVQFN package is footprint-compatible with prior NXP LIN families and AEC-Q100 qualified, making it well-suited for 12 V automotive in-cabin and under-hood environments. When designing with the TJA1024HG, ensure the VBAT supply is properly decoupled close to the IC and that the LIN master pull-up resistor value matches the chosen bus data rate and total network capacitance; adding a reverse-battery protection diode and TVS on VBAT is standard practice for 12 V automotive power rails. Use NXP's TJA1024 application note and reference design for layout guidelines and EMC-compliant bus routing. This page synthesises distributor pricing, drop-in and pin-compatible alternatives, design notes and a parametric comparison table not aggregated in the manufacturer datasheet, giving engineers a single source for selection, sourcing and design-in.

RFQ צור קשר
TJA1024HGZ - Quad 20 kBd LIN 2.2A Transceiver | NXP
TJA1024HGZ

TJA1024HGZ - Quad 20 kBd LIN 2.2A Transceiver | NXP

NXP Semiconductors TJA1024HGZ is a quad LIN 2.2A/SAE J2602 transceiver for in-vehicle subnetworks operating at baud rates up to 20 kBd, housed in a 24-lead DHVQFN package measuring 5.5 mm by 3.5 mm. The device supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 requirements identified in the supplied source data. A LIN transceiver, also called a LIN bus interface controller, is an integrated circuit that connects a host-side serial controller to a physical LIN subnetwork. It belongs to the hierarchy of bus interface IC, communication transceiver, vehicle network interface, and semiconductor. The TJA1024HGZ integrates four LIN channels, allowing one controller to connect to multiple low-speed vehicle-network nodes while retaining individual fault-management capabilities. The TJA1024 family converts controller-generated data streams into LIN bus signals shaped to reduce electromagnetic emissions, as stated in the NXP datasheet excerpt. Its LIN bus outputs are pulled high through internal termination resistors. The part is software compatible with the TJA1022, TJA1027, and TJA1029, making it useful when an established LIN protocol stack must connect to this physical-layer transceiver. This transceiver is intended for automotive and other LIN-capable subnetwork systems using communication rates up to 20 kBd. Potential circuit roles include body electronics, seat and door modules, climate-control interfaces, lighting controllers, and sensor gateways. The integrated quad-channel architecture can reduce the number of separate single-channel transceivers required on a controller board. Design work should verify supply voltage, pin mapping, bus termination, transceiver enable/control behavior, fault handling, and signal integrity against the complete manufacturer datasheet before layout release. The supplied distributor record identifies a 5 V to 18 V operating feature, while detailed electrical limits, timing values, thermal limits, and pin names were not included in the verified excerpts and therefore remain unconfirmed here. This product page combines the supplied manufacturer, distributor, and cross-reference evidence with practical engineering guidance. It distinguishes verified LIN standards and package information from unavailable specifications, helping designers identify the correct interface function without treating CAN alternatives as pin-compatible replacements.

RFQ צור קשר
TJA1027T/20/1J - 20 kBd LIN 2.2A Transceiver | NXP
TJA1027T/20/1J

TJA1027T/20/1J - 20 kBd LIN 2.2A Transceiver | NXP

The NXP Semiconductors TJA1027T/20/1J is a single-channel LIN bus transceiver operating at up to 20 kBd, with a 5 V to 18 V supply range and an 8-pin SOIC package. It is intended to connect an automotive LIN master or slave protocol controller to the physical LIN sub-network and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016. A LIN transceiver is the physical-layer interface between a microcontroller-based LIN node controller and the wired LIN bus. It converts controller transmit commands into a shaped bus signal, receives bus states for the controller, and provides the voltage translation and bus termination needed in an automotive low-speed serial network. The TJA1027 belongs to the interface IC and automotive communication transceiver hierarchy. The TJA1027T/20/1J supports LIN 2.0 through LIN 2.2A operation and SAE J2602 network requirements. Its transmit path creates an optimized LIN waveform intended to minimize electromagnetic emissions, while the LIN bus output is pulled high through an internal termination resistor. The 20 kBd operating rate supports typical in-vehicle LIN sub-networks rather than high-speed communication links. NXP identifies the TJA1027 as pin-compatible with the TJA1020 and TJA1021, and the broader datasheet compatibility statement also identifies TJA1022 and TJA1029 compatibility. Its 8-pin SOIC package supports conventional surface-mount assembly, while the automotive qualification designation supports use in vehicle electronic control units when the complete system requirements call for an automotive-grade component. Typical applications include LIN-controlled vehicle body modules, seat and door controllers, climate-control panels, switch-bank electronics, ambient-light sensors, and other low-speed vehicle sub-networks. In each case, the transceiver provides the physical bus interface while a separate LIN protocol controller or LIN-capable microcontroller handles frames, scheduling, diagnostics, and higher-layer communication. Designers should account for the transceiver and controller supply domains, LIN bus pull-up resistance, ground reference quality, waveform timing, EMC layout, and unused-pin treatment. The 5 V to 18 V operating range does not remove the need to protect the LIN line against automotive transients; the bus network must be evaluated using the application’s voltage, ground-offset, slew-rate, and fault-recovery requirements. This product page combines NXP protocol and compatibility information with package-focused alternatives, selection guidance, and implementation considerations. It distinguishes true pin-compatible options from merely similar LIN devices and highlights the operating conditions that should be checked before replacing an existing TJA1027 implementation.

RFQ צור קשר
TJA1027T/20/2Z - LIN 2.2A Automotive Transceiver | NXP
TJA1027T/20/2Z

TJA1027T/20/2Z - LIN 2.2A Automotive Transceiver | NXP

The NXP Semiconductors TJA1027T/20/2Z is an automotive LIN transceiver designed for in-vehicle sub-networks operating at baud rates up to 20 kBd. It operates from a 5 V to 18 V supply and is housed in an 8-pin SO package. The device interfaces a LIN leader or follower protocol controller with the physical LIN bus and supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. A LIN transceiver is the physical-layer interface between a microcontroller-based LIN protocol controller and a low-speed vehicle network. It converts the controller's transmit and receive signals into the standardized LIN bus waveform and presents received bus data to the controller. The TJA1027 belongs to the broader hierarchy of automotive network transceivers, bus-interface ICs, interface ICs, and semiconductors. The TJA1027 is optimized for electromagnetic-emission control and includes an internal pull-high arrangement on the LIN output. According to the NXP manufacturer datasheet, its transmit data stream is converted into an optimized bus signal intended to minimize electromagnetic emissions. The device also provides pin compatibility with the TJA1020 and TJA1021, allowing evaluation of functional alternatives within the same 8-pin footprint. Automotive qualification information, exact absolute maximum ratings, current consumption, slew-rate limits, and detailed timing values should be confirmed in the manufacturer datasheet before a production release. The /20 ordering variant identifies a specific temperature and packaging configuration, while /2Z is the reeled ordering suffix. These ordering codes should not be changed without checking the associated NXP ordering information and labeling requirements. Typical applications include LIN sub-networks in body-control modules, seat and door controllers, climate-control panels, lighting modules, sensor gateways, and other automotive electronic control units. Because LIN is a single-wire, low-speed network, the transceiver also needs correct board-level bus termination, grounding, protection, and decoupling to maintain signal integrity in electrically harsh vehicle environments. Keep the transceiver supply and ground connections compact on the PCB, and route the LIN connection to minimize sensitive-loop area. Add the manufacturer's recommended decoupling and protection components near the device, and verify that the external bus network complies with LIN 2.2A and SAE J2602 timing requirements. This page combines exact product facts, interface standards, pin-compatible alternatives, comparison guidance, and practical PCB considerations to support component selection, cross-reference work, and PCB design for LIN 2.2A automotive networks.

RFQ צור קשר
TJA1027TK/20/1 - LIN 2.2A Transceiver | NXP
TJA1027TK/20/1

TJA1027TK/20/1 - LIN 2.2A Transceiver | NXP

NXP Semiconductors TJA1027TK/20/1 is an automotive LIN bus transceiver supporting data rates up to 20 kBd in an 8-pin HVSON package with a 3 mm by 3 mm body size. It is intended for in-vehicle sub-networks and complies with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 (12 V) requirements. A Local Interconnect Network transceiver is the physical-layer interface between a LIN protocol controller and the vehicle's LIN wiring. It combines the bus transmitter, receiver, voltage-domain conversion, and protection functions required to connect a microcontroller-based master or slave node to a low-cost, single-wire automotive network. LIN belongs to the broader hierarchy of automotive interface ICs, communication transceivers, interface ICs, and semiconductors. Key characteristics include operation at up to 20 kBd, compatibility with LIN 2.0 through LIN 2.2A, and compliance with SAE J2602 and ISO 17987-4:2016 for 12 V systems. The TJA1027 is pin-compatible with the TJA1020 and TJA1021 families, making it useful when a design must consolidate LIN transceiver sourcing while retaining the established physical footprint and board-level implementation. The TJA1027 integrates the LIN physical-layer transmitter and receiver with logic-side supply support, allowing a protocol controller to communicate through the vehicle LIN bus. Its compliance targets cover both LIN 2.2A and SAE J2602 requirements, providing a defined basis for automotive sub-network designs. Exact operating limits, electrical thresholds, bus-loading limits, and transceiver timing should be checked against the manufacturer datasheet for the selected ordering code. Typical uses include LIN master nodes, LIN slave nodes, body-control modules, seat and door modules, climate-control peripherals, switch interfaces, sensors, and lighting modules. The device is particularly relevant to 12 V vehicle architectures operating below the protocol's 20 kBd maximum baud rate, where standardized LIN physical-layer behavior and compact package size simplify harness-based sub-networks. When laying out the circuit, follow the pin-description table and recommended application circuit in the manufacturer datasheet. Pay particular attention to transceiver supply connections, ground return, LIN bus routing, external bus-interface components, and protection requirements. PCB signal integrity and automotive EMC performance depend on keeping the bus path compact and following the manufacturer's reference layout. This product page combines NXP protocol-compliance information, drop-in family options, application guidance, and practical design notes to support component selection and PCB planning. It is intended to help engineers identify whether the TJA1027TK/20/1 matches the required LIN standard, package, bus rate, and automotive integration constraints.

RFQ צור קשר
TJA1029T - 20 kBd LIN 2.2 Automotive Transceiver | NXP
TJA1029T

TJA1029T - 20 kBd LIN 2.2 Automotive Transceiver | NXP

The NXP Semiconductors TJA1029T is a LIN physical-layer transceiver that connects a Local Interconnect Network master or slave protocol controller to the physical vehicle bus. It supports data rates up to 20 kBd, is intended primarily for in-vehicle subnetworks, and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. The device is supplied in an 8-pin SO package designated 8-SO. A LIN transceiver is a low-speed automotive network interface that converts serial protocol-controller data into a shaped bus signal and converts received bus levels back into logic-compatible data. Within the vehicle-network hierarchy, the TJA1029T belongs to the LIN physical layer, below the LIN protocol controller and above the twisted-pair LIN bus. This division separates frame-level communication and fault management from the electrical interface to the bus. The TJA1029T converts the protocol controller's transmit data stream into an optimized bus signal intended to minimize electromagnetic emissions. Its internal LIN-bus output pull-up and its ability to operate as either a master or slave physical interface suit vehicle subnetwork nodes. The NXP datasheet identifies the TJA1029 as pin-compatible with the TJA1020, TJA1021, TJA1022, TJA1027, and MC33662(B), providing a documented basis for same-footprint replacement evaluation. The device is primarily designed for automotive LIN subnets operating at up to 20 kBd. Typical implementation places the transceiver beside a LIN-compatible microcontroller, connects TXD and RXD to the controller, and connects the LIN pin to the vehicle's LIN bus. In this arrangement, the microcontroller handles protocol frames, addressing, diagnostics, and higher-level vehicle functions, while the TJA1029T performs the physical signaling and bus-interface functions. Because LIN buses commonly operate in harsh automotive environments, the complete transceiver and module design must be validated for the intended voltage, temperature, ESD, emission, and immunity requirements. The supplied verified data does not state the complete electrical limits, thermal ratings, timeout options, or exact pin names, so those details must be confirmed in the manufacturer datasheet and the selected ordering variant before schematic release or PCB sign-off. The main engineering tradeoff is version-specific functionality. Ordering codes such as TJA1029T/20/1J and TJA1029T/2Z appear in distributor records, with the latter identified as including a TXD dominant timeout, but the supplied excerpts do not provide a complete variant matrix. Engineers should therefore match the exact base-device and timeout features required by the LIN controller, firmware, safety analysis, and production BOM rather than selecting only by connector or package. This page consolidates the verified manufacturer statements, distributor availability references, documented pin-compatible alternatives, package information, and practical selection guidance. It also separates verified facts from unprovided electrical details, helping engineers identify valid drop-in candidates while avoiding unsupported assumptions about pricing, pin assignments, lifecycle guarantees, or automotive qualification.

RFQ צור קשר
TJA1029T/20/1J - 20 kbaud LIN Transceiver | NXP | Automotive
TJA1029T/20/1J

TJA1029T/20/1J - 20 kbaud LIN Transceiver | NXP | Automotive

The NXP TJA1029T/20/1J is an automotive LIN physical-layer transceiver with a 20 kbaud maximum bus speed, 5 V to 18 V supply range, and an 8-pin SOIC package. It interfaces a LIN master or slave protocol controller with the physical LIN bus and supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. A LIN transceiver is the physical-layer interface within a Local Interconnect Network. The LIN bus is a low-cost, single-wire automotive network derived from the automotive CAN hierarchy and commonly used for vehicle subnets. It connects sensors, actuators, switches, and electronic control units through a protocol controller, while the transceiver converts controller logic into a properly shaped bus signal and returns received bus data to the controller. The TJA1029 is optimized for in-vehicle subnetworks operating at baud rates up to 20 kBd. Its LIN bus output is shaped to minimize electromagnetic emissions, and the bus output is pulled high through an internal termination resistor. A TXD dominant-timeout function helps protect the network when the protocol controller fails to release the transmit signal. The device operates from 5 V to 18 V and is specified for an ambient temperature range of -40 °C to 150 °C. The TJA1029 is pin-compatible with the TJA1020, TJA1021, TJA1022, TJA1027, and MC33662(B) families according to the NXP datasheet. This compatibility supports design reuse when a product requires a different LIN transceiver feature set, although firmware, timing, protection, and application requirements should be reviewed before substitution. The integrated bus interface reduces the component count required for LIN physical-layer connections. Typical uses include body-control modules, door and seat controllers, climate-control interfaces, sensor gateways, lighting controllers, seat-memory modules, and other low-speed automotive subnetworks. The 20 kBd limit matches conventional LIN communication rates, while the broad 5 V to 18 V supply range supports automotive electrical environments when used with appropriate protection and decoupling. When laying out the PCB, use the manufacturer pin-definition table and recommended application circuit. Place the device-side and bus-side capacitors close to their intended pins, keep the LIN connection away from sensitive analog and high-speed digital traces, and provide a correctly sized bus termination. The LIN bus requires one master termination and slave-side pull-up arrangements defined by the network design. This page organizes the TJA1029T/20/1J specifications, protocol support, pin-compatible alternatives, application guidance, and design checks into one engineering reference. It helps distinguish direct family replacements from broader LIN-transceiver choices while keeping package compatibility and automotive operating requirements central to the selection process.

RFQ צור קשר
TJA1029T/2Z - 20 kBd LIN 2.2A Transceiver | NXP
TJA1029T/2Z

TJA1029T/2Z - 20 kBd LIN 2.2A Transceiver | NXP

The NXP Semiconductors TJA1029T/2Z is an automotive LIN physical-layer transceiver supporting bus speeds up to 20 kBd, LIN 2.0 through LIN 2.2A operation, and SAE J2602 compliance in an 8-pin SOIC package. It interfaces a LIN leader or follower protocol controller with the physical bus and adds a TXD dominant-timeout feature for systems requiring controlled transmitter behavior. A LIN transceiver is a physical-layer interface IC that combines a logic-level transmitter, receiver, bus-driver protection, and LIN bus termination functions. In the vehicle networking hierarchy, LIN connects low-cost nodes for body electronics and in-vehicle subnetworks, while the protocol controller manages frames and scheduling above the transceiver. The TJA1029 therefore bridges a digital controller and the wired LIN network rather than operating as a standalone bus controller. According to NXP product information, the device supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. Its principal purpose is in-vehicle subnetworks operating at up to 20 kBd. The verified distributor data identifies TJA1029T/2Z as a half-duplex LIN transceiver with TXD dominant timeout, which is useful where the host controller must avoid an indefinitely asserted transmit command. NXP states that TJA1029 is pin-compatible with the TJA1020, TJA1021, TJA1022, and TJA1027. That compatibility creates a controlled upgrade path within the same NXP interface family, although designers must still verify electrical limits, timing, fault behavior, package suffix, and production requirements for the specific replacement. The TJA1021T/20/C from the site MPN list is therefore an important family reference, not an automatically interchangeable part without checking its ordering code. Typical uses include LIN-controlled vehicle body modules, door and seat controllers, climate-control interfaces, lighting modules, sensor gateways, and other low-speed automotive subnetworks. The 20 kBd capability and LIN 2.2A/SAE J2602 positioning align it with established in-vehicle network architectures rather than high-speed body communication buses. The critical design check is the power and bus environment. Use the manufacturer datasheet for the exact VCC range, LIN transceiver operating limits, pin names, external termination, ESD requirements, and thermal limits before layout release. In particular, verify whether the selected SOIC footprint and pin mapping match the exact package variant being assembled.

RFQ צור קשר
TJA1029TK - 2.2A LIN Transceiver | NXP Semiconductors
TJA1029TK

TJA1029TK - 2.2A LIN Transceiver | NXP Semiconductors

NXP Semiconductors TJA1029TK is a 2.2 A LIN 2.2A and SAE J2602 transceiver with a transmit-data dominant timeout function, supplied in an 8-pin HVSON package measuring 3 x 3 mm. It supports LIN bus communication at rates up to 20 kBd and connects a Local Interconnect Network master or follower protocol controller to the physical LIN bus. A LIN transceiver is a physical-layer interface within an automotive communication network. The Local Interconnect Network is a low-cost, single-wire serial bus commonly used to connect relatively simple vehicle nodes such as sensors, switches, seat modules, and door electronics. A LIN transceiver converts the controller's transmit and receive signals into a bus-compatible waveform and reports received bus data back to the controller. The TJA1029 supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 communication requirements. Its stated 2.2 A bus-output capability supports the physical drive required in vehicle electrical environments, while its 20 kBd maximum signaling rate matches the communication range of LIN 2.x networks. The TXD dominant-timeout feature adds a defined protection function for the transmit-data path. NXP identifies the TJA1029 as pin-compatible with the TJA1020, TJA1021, TJA1022, and TJA1027 families. This compatibility provides a practical basis for PCB reuse when a design is being revised, although the selected replacement must still be checked for protocol version, timeout behavior, electrical limits, and ordering suffix requirements. Typical uses include LIN subnets containing door controls, climate-control modules, body controllers, seat electronics, lighting interfaces, and other distributed vehicle nodes. The device can serve as the physical interface in either a LIN leader or follower node because the protocol controller determines the network role independently of the transceiver. For layout, place the TJA1029 close to the LIN connector or protected bus entry point and minimize the distance of the LIN trace. The external bus network, connector, pull-up arrangement, protection components, and vehicle-level EMC requirements must be evaluated with the complete reference design rather than as isolated component choices. This product page consolidates the TJA1029TK identification, LIN standard coverage, known package information, pin-compatible family references, and practical replacement considerations. It also separates confirmed device facts from parameters that require confirmation in the NXP datasheet or a design-specific qualification before production release.

RFQ צור קשר
TJA1040T/CM - 1 MBaud CAN Transceiver | NXP
TJA1040T/CM

TJA1040T/CM - 1 MBaud CAN Transceiver | NXP

The NXP Semiconductors TJA1040T/CM is a high-speed CAN transceiver rated for operation up to 1 MBaud and supplied in an 8-pin SO package. It provides differential transmit capability to the physical CAN bus and differential receive capability to a CAN protocol controller, making it an interface between controller-area-network logic and vehicle or industrial bus wiring. A CAN transceiver is a physical-layer interface IC within the broader interface-IC hierarchy. It converts the controller’s digital logic signals into differential bus signaling and converts differential bus levels back into logic-compatible receive signals. The TJA1040 is intended primarily for high-speed passenger-car CAN networks, where robust differential signaling, standby control, and electromagnetic compatibility are important. The verified manufacturer information identifies differential transmission, differential reception, high-speed operation up to 1 MBaud, and standby-mode capability as principal device features. The distributor record identifies the TJA1040T/CM,118 ordering form as an 8-pin SO CAN-bus transceiver. Detailed electrical limits, loop-delay values, bus-fault behavior, and package dimensions were not supplied in the verified extract and therefore require confirmation from the manufacturer datasheet before design release. Typical uses include passenger-vehicle body and powertrain CAN networks, automotive control modules, CAN gateways, and industrial equipment that uses a 5 V CAN physical layer. The transceiver is intended to operate with a compatible CAN controller rather than as a standalone bus controller. Its differential bus interface supports robust communication over cable networks, while the standby function can reduce activity when the node is not communicating. Designers should preserve the pin assignment, supply decoupling, CANH/CANL routing, termination, and common-mode protection described by the manufacturer. The verified source set does not include the complete pinout, absolute maximum ratings, thermal data, or EMC test values, so those details must not be inferred. This page combines official NXP information with distributor records and explicitly marks unavailable parameters rather than estimating them. TJA1040T/CM is a legacy EoL-positioned part according to the supplied migration context. For new designs, engineers should compare it with current NXP or third-party CAN transceivers and verify pin, electrical, lifecycle, and qualification compatibility before treating any replacement as drop-in.

RFQ צור קשר
TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors
TJA1040T/N1

TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1040T/N1 is a high-speed CAN bus transceiver with a maximum signaling rate of 1 Mbit/s, supplied in an 8-pin SO package. It provides the physical-layer interface between a CAN protocol controller and the differential CAN bus, combining a differential transmitter with a differential receiver. The device is intended primarily for high-speed in-vehicle passenger-car networks, where a compact controller-to-bus interface enables distributed automotive electronics to exchange safety, body, and powertrain-related data. A CAN transceiver is a semiconductor interface device that converts logic-level transmit and receive signals into the differential signaling used on a Controller Area Network. In the hierarchy of electronic components, the TJA1040T/N1 is an interface IC, specifically a CAN physical-layer transceiver. A host microcontroller or dedicated CAN controller handles message framing, arbitration, filtering, and protocol timing, while the transceiver translates those controller signals into robust bus-level voltages and converts received bus states into logic-compatible data. The key operating headline is a maximum data rate of 1 Mbit/s, with differential transmit and receive capability. The 8-SO package keeps the physical interface compact for automotive electronic control units and other embedded CAN systems. The NXP product page specifically identifies passenger cars as the principal application environment. These characteristics make the TJA1040T/N1 relevant to designs that need a conventional high-speed CAN physical layer rather than a low-speed fault-tolerant body-network interface. The TJA1040T/N1 belongs to an older generation of CAN transceivers whose successor products can add functions such as standby control, split-buffer operation, or expanded I/O voltage support. Its core role remains straightforward: TXD accepts a controller-side transmit signal, RXD presents the received bus state to the controller, and the differential CANH and CANL pins connect to the bus. Exact electrical limits, loopback behavior, and pin functions should be checked against the manufacturer data sheet before final circuit release. Typical applications include passenger-car body-control modules, powertrain controllers, automotive comfort systems, CAN-based sensors, and industrial or embedded equipment using a standard 1 Mbit/s CAN network. In an automotive control unit, the transceiver provides the physical link between a CAN controller and the two-wire bus while leaving protocol functions to the controller. Its differential interface also suits systems where minimizing susceptibility to common-mode noise is important. PCB design should preserve the short, symmetric CANH and CANL connection between the transceiver and the bus connector, keep the connector and bus stubs short, and provide the required decoupling directly at the device supply pins. The 8-SO footprint simplifies assembly but requires careful escape routing around the two bus pins. Review the recommended application circuit, termination requirements, supply voltage, and loopback configuration in the NXP data sheet when laying out the module. This product record combines the manufacturer interface description, ordering information, package details, lifecycle information, and replacement guidance with practical PCB considerations. It also distinguishes strict same-footprint substitutes from newer CAN transceivers that offer additional functions but may require different pin interpretation or board-level qualification.

RFQ צור קשר
TJA1040T/VM - 1Mbit CAN Transceiver | NXP | Automotive
TJA1040T/VM

TJA1040T/VM - 1Mbit CAN Transceiver | NXP | Automotive

The NXP TJA1040T/VM is a high-speed CAN physical-layer transceiver rated for data rates up to 1 Mbaud, operating from a 5 V supply, and packaged in an 8-pin SO small-outline package. It provides the differential transmitter and receiver interface between a CAN protocol controller and the physical CAN bus, making it suitable for passenger-car and other high-speed Controller Area Network systems. A CAN transceiver is an interface IC within the broader hierarchy of CAN interface devices, bus transceivers, wired-network interfaces, and semiconductors. It translates logic-level TXD and RXD signals into the differential CANH and CANL bus conductors and converts received bus differential voltage back into a logic-compatible RXD signal. This physical-layer function separates CAN protocol processing in a controller from the electrical drive, receive, and bus-failure behavior implemented by the transceiver. The TJA1040 supports high-speed CAN operation up to 1 Mbaud, making it appropriate for engine, chassis, body, and other automotive networks operating within that bandwidth. Its 5 V supply arrangement matches conventional automotive CAN interface environments. The device also provides power-down and standby operating states, allowing a system to reduce activity when communication is not required. The listed 8-SO package supports compact surface-mount PCB layouts. The transceiver architecture combines a differential CAN output stage with a differential input receiver. TXD is the controller-facing transmit input, while RXD is the controller-facing receive output. CANH and CANL provide the physical connection to the bus, VCC supplies the transceiver, VIO supports the interface voltage domain, and EN provides operating-state control. These functions allow a CAN controller to communicate through a multi-conductor differential bus while keeping protocol handling separate from bus signaling. Typical applications include passenger-car CAN networks, automotive body and chassis control modules, powertrain control equipment, industrial CAN equipment operating at compatible bus speeds, and embedded CAN gateways. In each application, the controller generates TXD and receives RXD, while the TJA1040 handles the physical bus interface. Board design must preserve the transceiver's supply, reference-ground, input, and bus-connection requirements to maintain signal integrity. When laying out the PCB, place the transceiver and its local decoupling capacitor close to the associated CAN controller, keep CANH and CANL routing compact and symmetrical, and provide the bus termination and common-mode network required by the selected CAN topology. Differential routing reduces sensitivity to external noise, while correct termination prevents excessive reflections from degrading communication at the maximum supported data rate. This product page combines the NXP device description with package, interface, application, comparison, and layout guidance. It also distinguishes verified source facts from engineering choices that depend on bus topology, termination strategy, controller supply voltage, and EMC validation.

RFQ צור קשר
TJA1041AT - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT

TJA1041AT - 1 Mbit/s High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1041AT is a high-speed CAN transceiver intended for automotive Controller Area Network nodes operating at data rates up to 1 Mbit/s. It provides differential transmit capability to the CAN bus and differential receive capability to the CAN protocol controller, with a 4.75 V to 5.25 V supply range and a 14-pin SOIC surface-mount package. The device is designed for use with a 5 V CAN controller interface. A CAN transceiver is the physical-layer interface between a CAN protocol controller and a wired CAN bus. Within the hierarchy of CAN interface ICs, CAN transceivers sit between microcontrollers or dedicated CAN controllers and the differential bus. They combine a transmitter, receiver, bus-driver protection, and logic-level interfaces into one component. This integration allows a protocol controller to exchange messages with other CAN nodes while the transceiver handles the physical signaling characteristics of the bus. The TJA1041AT supports CAN data rates up to 1 Mbit/s and is compatible with the ISO 11898 standard. Its differential transmitter and receiver support communication over a balanced CAN bus, while its digital transmit and receive pins connect to a CAN controller. NXP identifies the TJA1041AT as an end-of-life product, so long-lived automotive, industrial, and transportation programs should confirm lifecycle strategy and replacement planning with NXP before committing new production volumes. The SOIC-14 package provides separate connections for logic supply, transceiver supply, transmit data, receive data, standby control, CANH, and CANL. Its surface-mount construction supports automated PCB assembly, while the comparatively large lead pitch facilitates inspection and rework compared with fine-pitch packages. Precise pin names, truth-table behavior, electrical limits, and unused-pin connections should be assigned directly from the pin-description table and application information in the manufacturer datasheet. Typical uses include automotive body and powertrain networking, industrial automation equipment, transportation controllers, embedded CAN gateways, and diagnostic interfaces. The 1 Mbit/s capability suits conventional high-speed CAN networks used throughout vehicle and factory automation systems. A suitable host controller must support the device's logic levels, supply arrangement, standby behavior, and CAN protocol requirements. Designers should preserve the recommended transceiver and controller grounding arrangement, route CANH and CANL as a differential pair, and place protection or termination components where the bus topology requires them. Bus termination, common-mode range, loop delay, radiated emissions, and fault tolerance must be evaluated at system level rather than inferred solely from the nominal data rate. This product page combines the manufacturer lifecycle status, datasheet characteristics, application guidance, and cross-reference assessment to support engineering selection. It also distinguishes a genuine PCB-footprint replacement from merely similar CAN devices, avoiding the unsafe assumption that equal functionality automatically means pin-to-pin compatibility.

RFQ צור קשר
TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/N

TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/N is a high-speed CAN bus transceiver for automotive applications operating at data rates up to 1 Mbit/s. It provides a physical-layer interface between a CAN protocol controller and the differential CAN bus, offering differential transmit and receive functions in a 14-pin SO package. Its nominal 5 V supply range is 4.75 V to 5.25 V. A CAN transceiver, also called a CAN physical-layer interface, converts logic-level signals from a CAN controller into differential bus signals and converts the received bus state back into a logic signal. Within the automotive electronics hierarchy, the TJA1041AT/N belongs to the CAN interface IC class, connecting the protocol-control layer to the physical communication bus. The principal feature of the TJA1041AT/N is its support for high-speed CAN communication up to 1 Mbit/s. Differential CAN signaling improves immunity to electromagnetic noise, while the transceiver's transmit and receive paths integrate the controller and bus into one physical-layer solution. The device is specifically intended for automotive high-speed CAN nodes, where robust differential signaling, compact packaging, and predictable interoperability are important. The TJA1041A family uses a nominal 5 V operating environment, with the documented supply range of 4.75 V to 5.25 V. The 14-pin SO package supports surface-mount PCB assembly and provides the CANH and CANL bus connections together with controller-facing TXD, RXD, and error-status signaling. Exact pin functions, absolute maximum ratings, loop-delay limits, and output-stage characteristics should be taken from the manufacturer datasheet. Typical deployments include automotive body and comfort modules, powertrain controllers, gateway units, cluster electronics, infotainment systems, and industrial CAN equipment that implements a compatible high-speed CAN physical layer. In these systems, the transceiver replaces discrete driver and receiver circuitry around the CAN controller while keeping the PCB layout compact. When laying out the circuit, place the transceiver close to the bus connector and route CANH and CANL as a matched differential pair. Keep the connection from CANH and CANL through the connector as short as practical, follow the datasheet recommendations for termination, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. The NXP product page identifies TJA1041AT as end of life, so new designs should confirm the recommended successor before committing the footprint. This page combines the manufacturer's product information, datasheet links, distributor records, lifecycle information, and packaging details with practical application guidance, comparison parameters, and board-level design notes. It is intended to accelerate component selection and design-in work while keeping the final engineering decisions anchored to the official NXP documentation.

RFQ צור קשר
TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/V

TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/V is a high-speed CAN transceiver designed for automotive Controller Area Network nodes operating at data rates up to 1 Mbit/s. It provides differential transmit and receive capabilities between a CAN protocol controller and the physical CAN bus, operates from a 4.75 V to 5.25 V supply, and is offered in a 14-pin SO package. The device is intended for automotive electronic control units, body modules, instrumentation systems, and other embedded networking equipment that require a robust interface between a digital CAN controller and a differential bus. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. A CAN controller generates and interprets digital protocol frames, while the physical-layer transceiver converts controller signals into a differential CAN bus waveform and converts received bus levels back into logic-compatible receive data. The TJA1041AT/V therefore belongs to the CAN transceiver family, which operates at the physical-bus layer beneath communication controllers, embedded processors, and complete automotive electronic control units. Key operating features include support for high-speed CAN communication up to 1 Mbit/s, a 4.75 V minimum operating supply, a 5.25 V maximum operating supply, differential bus transmission, and differential bus reception. Its transceiver architecture allows a host controller to remain separate from the physical bus wiring while providing the electrical interface required for multi-node communication. The 14-pin SO package supports compact surface-mount assembly in automotive control-unit designs. The TJA1041A family is associated with ISO 11898 high-speed CAN communication and provides compatibility with CAN protocol controllers that provide TXD and RXD logic signals. The CANH and CANL connections carry complementary differential bus levels. This differential signaling improves common-mode noise rejection in vehicle electrical environments, where switching loads, alternator systems, and other transient-producing equipment can disturb the communication network. Typical applications include automotive body-control modules, powertrain controllers, gateway units, dashboard electronics, seat and door modules, lighting controllers, small electric motors, and industrial or transportation equipment using a CAN bus. In these systems, the transceiver is placed between the host CAN controller and the CANH and CANL network conductors. PCB routing, termination, grounding, and protection remain critical because the transceiver is only one element of the complete physical-layer network. Design the power and signal paths carefully around the 4.75 V to 5.25 V operating range. Decoupling should be placed close to the supply pins, the CANH and CANL traces should follow controlled-impedance routing practices, and the bus should use the termination strategy specified by the CAN network design. Protection components may be added when the cable environment includes severe automotive transients, provided their capacitance and clamping behavior do not distort the differential signal. This product page combines the NXP technical description with lifecycle information, package identification, practical interface guidance, sourcing questions, and clearly qualified replacement analysis. It also highlights where an existing design can be reused and where a new PCB and EMC validation are required before changing CAN transceivers.

RFQ צור קשר