מוצרים (44,000+)

TLV2452AIDGKR-Q1 - Dual 220kHz RRIO Op Amp, 23uA | TI
TLV2452AIDGKR-Q1

TLV2452AIDGKR-Q1 - Dual 220kHz RRIO Op Amp, 23uA | TI

The Texas Instruments TLV2452AIDGKR-Q1 is an automotive-grade (AEC-Q100 qualified) dual micropower rail-to-rail input/output operational amplifier consuming only 23 uA per channel while delivering 220 kHz of gain-bandwidth product, supplied in an 8-pin VSSOP (DGK) package. It operates from a single 2.7 V to 6 V supply and is qualified for AEC-Q100 Grade 1 temperature (-40C to +125C). A rail-to-rail input/output operational amplifier is a type of precision op amp within the broader analog amplifier family whose input common-mode range and output voltage swing extend to within millivolts of both supply rails. This maximizes dynamic range in low-voltage, single-supply systems where signal levels approach the rails, a capability conventional op amps cannot provide. Key features include the industry-leading 23 uA/channel quiescent current (far below competitive devices at similar bandwidth), 220 kHz gain-bandwidth product, rail-to-rail input and output (RRIO) operation, and high output drive capability for its power class. The dual-channel integration saves board space and reduces BOM count in multi-channel signal chains. The TLV245x family achieves its performance point through a trimmed CMOS input stage combined with rail-to-rail output buffer architecture, providing stable gain-bandwidth across the full load range. The related TLV245x family also offers shutdown variants (TLV2453/2455) for further average-power reduction in duty-cycled systems. Typical automotive and industrial applications include battery monitoring and current sensing front ends, low-power sensor signal conditioning, portable instrumentation, and microcontroller ADC driver stages, where micropower consumption directly extends battery life and reduces self-heating. Design consideration: because gain-bandwidth is 220 kHz, keep closed-loop gains moderate for signal bandwidths above a few tens of kHz; with 23 uA supply current, output current drive is limited, so avoid heavy capacitive loads without isolation resistors.

RFQ צור קשר
TLV2452CP - Dual 6V RRIO Op Amp | Texas Instruments
TLV2452CP

TLV2452CP - Dual 6V RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2452CP is a dual, rail-to-rail input and output operational amplifier designed for low-voltage, low-power signal-conditioning systems. Its key operating characteristics include a 6 V maximum supply, 220 kHz gain-bandwidth product, and 23 µA quiescent current per channel. The device is offered in an 8-pin PDIP package for through-hole assembly. An operational amplifier is an analog semiconductor that amplifies the voltage difference between its differential inputs while providing high input impedance and low output impedance. The TLV2452CP belongs to the rail-to-rail input and output operational-amplifier family within the broader voltage-feedback amplifier and analog signal-processing hierarchy. Rail-to-rail operation allows input and output voltage swings to approach the supply rails, making this amplifier useful in battery-powered and compact embedded systems. The dual configuration provides two independent amplifier channels in one package, reducing board area when a system needs matched or simultaneous analog functions. The 220 kHz gain-bandwidth product is suitable for low-frequency sensor conditioning, audio pathways, and general-purpose signal processing. Its 23 µA quiescent current per channel reduces supply demand in battery-operated equipment, while rail-to-rail input capability improves dynamic range when the signal approaches either supply rail. The TLV2452 family also includes shutdown functionality, allowing the amplifier channels to be disabled when they are not required. Although the TLV2452CP is a commercial-temperature variant in the PDIP package, shutdown control, offset voltage, common-mode behavior, and output-current capability should be checked against the complete operating requirements before committing a design. The 8-pin PDIP format provides a large lead pitch, useful for prototypes, education, repair, and applications where through-hole assembly is preferred over fine-pitch surface-mount packaging. Typical applications include portable instrumentation, low-voltage sensor interfaces, battery-powered monitoring, audio input conditioning, and industrial control modules. Two channels can implement differential signal conditioning, active filtering, level shifting, transimpedance buffering, or independent gain stages. The low quiescent current is particularly useful when average standby power matters more than high-frequency closed-loop performance. The principal design trade-off is speed. A 220 kHz amplifier favors low-power and compact analog conditioning rather than high-bandwidth signal processing. Designers should verify source impedance, output-load compatibility, settling requirements, noise performance, and stability around the selected gain before finalizing the external resistor and capacitor network. This product record combines the manufacturer's device specifications with practical guidance on package selection, thermal and layout considerations, low-power operation, drop-in family options, and design trade-offs. It also identifies where application-specific electrical details require confirmation from the manufacturer datasheet before production release.

RFQ צור קשר
TLV2453CN - Dual 6V RRIO Op Amp with Shutdown | TI
TLV2453CN

TLV2453CN - Dual 6V RRIO Op Amp with Shutdown | TI

The Texas Instruments TLV2453CN is a dual, 6 V, rail-to-rail input/output operational amplifier with shutdown in a 14-PDIP package. It combines a 220 kHz gain-bandwidth product with low quiescent current of 23 uA per channel, making it suitable for low-power analog signal conditioning. A rail-to-rail input/output operational amplifier is an analog amplifier whose input and output voltage ranges extend toward the positive and negative supply rails. Its place in the signal-chain hierarchy is amplifier IC, analog integrated circuit, semiconductor, and ultimately electronic component. The TLV2453 family serves general-purpose applications where low power, broad output swing, and shutdown control are more important than high bandwidth. Key features include two amplifier channels, 220 kHz gain-bandwidth product, 23 uA per-channel quiescent current, rail-to-rail inputs and outputs, and a shutdown function. The amplifier also provides a typical 20 uV input offset voltage and approximately ±10 mA output drive capability. These characteristics make the device useful for battery-powered instrumentation, sensor interfaces, and low-energy signal-processing systems. The 220 kHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies while keeping quiescent power consumption low. Because the output can operate close to the supply rails, a 6 V system can retain useful signal range without a rail-to-rail output stage. Rail-to-rail input behavior improves common-mode range, although the input common-mode range, output swing limits, stability behavior, and noise characteristics should be checked against the manufacturer datasheet for the intended operating conditions. Typical applications include portable sensor conditioning, low-current data acquisition, battery-powered monitoring, industrial signal interfaces, and embedded analog measurement systems. In each case, the 23 uA per-channel quiescent current reduces standing power demand, while the shutdown pin can disable the amplifier when the system does not require continuous operation. Design around the 6 V maximum supply named for the device and verify input and output signal amplitudes before applying it to a precision measurement path. Keep sensitive input and feedback nodes away from switching nodes and noisy supply traces. When shutdown timing matters, account for the device's transition behavior and ensure the control signal remains within its specified voltage range. This page organizes the TLV2453CN's electrical characteristics, package information, application guidance, design considerations, and verified substitute availability into an engineering-focused selection resource. It also distinguishes documented drop-in alternatives from parts that require a different footprint or a broader design review.

RFQ צור קשר
TLV2455CD - 220kHz Low-Power RRIO Op Amp | Texas Instruments
TLV2455CD

TLV2455CD - 220kHz Low-Power RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2455CD is a quad, low-power, rail-to-rail input/output operational amplifier with a 6 V maximum supply, 220 kHz gain-bandwidth product, and approximately 23 µA quiescent current per channel. The device is packaged in a 16-pin SOIC and is identified as a standard general-purpose amplifier. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its two inputs. The TLV2455 belongs to the rail-to-rail input/output amplifier family within the broader operational amplifier, analog IC, and semiconductor hierarchies. Rail-to-rail input operation permits common-mode input voltages to approach the supply rails, while rail-to-rail output operation extends useful output swing toward both rails. The TLV2455CD combines four amplifier channels with approximately 23 µA of supply consumption per channel and a 220 kHz gain-bandwidth product. These characteristics make it suitable for portable and low-power signal-processing systems in which a conventional higher-current amplifier would waste available power. The family also includes a shutdown function, allowing connected circuitry to reduce supply consumption when operation is not required. The TLV2455 family operates from a 6 V maximum supply and is described by Texas Instruments as a low-quiescent-current amplifier family. Rail-to-rail input and output behavior is particularly useful when signals remain close to the positive or negative supply rail. Designers should still evaluate output swing, common-mode range, capacitive loading, and stability in the exact gain configuration rather than assuming ideal operation at the supply limits. Typical uses include low-power sensor interfaces, buffered analog measurement circuits, portable instrumentation, battery-powered signal conditioning, and general-purpose analog amplification. The quad-channel configuration can reduce the number of packages required when a design needs several low-frequency or moderate-bandwidth amplifier stages, particularly when the individual channels do not require simultaneous operation. A key design consideration is shutdown-state behavior and board-level power management. The shutdown pin should be driven with levels compatible with the device supply, and unused amplifier inputs must be returned to a valid common-mode potential rather than left floating. Input and output stability should be checked with the intended source impedance, load capacitance, feedback network, and PCB parasitics. This product page combines the manufacturer’s device identity with package, performance, application, and replacement guidance. It also distinguishes electrically similar ordering options from true pin-compatible alternatives and highlights the design checks engineers should complete before assigning TLV2455CD to a new analog board.

RFQ צור קשר
TLV2455CN - 220 kHz Quad Rail-to-Rail Op Amp | Texas Instruments
TLV2455CN

TLV2455CN - 220 kHz Quad Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments TLV2455CN is a four-circuit, general-purpose operational amplifier with rail-to-rail input and output capability, a 220 kHz gain-bandwidth product, and 23 uA typical quiescent current, housed in a 16-pin PDIP package. The device includes a shutdown function and is intended for low-power applications requiring four amplifiers in one package. Its low operating current makes the TLV2455CN useful in portable instrumentation, sensor interfaces, audio signal paths, and general-purpose analog signal conditioning where supply efficiency and compactness are important. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The rail-to-rail input stage accepts signals close to the positive and negative supply rails, while the rail-to-rail output stage can swing close to those limits under suitable load conditions. Within the broader hierarchy, an operational amplifier is a linear amplifier and analog IC used for buffering, amplification, filtering, comparisons, feedback control, and signal conditioning. The TLV2455CN provides four rail-to-rail amplifiers, 220 kHz gain-bandwidth product, and approximately 23 uA typical quiescent current. These characteristics make it appropriate for general-purpose low-power designs that do not require the bandwidth of a high-speed amplifier. A shutdown function allows the circuit to reduce power consumption when the analog section is inactive. Its PDIP package also supports conventional through-hole assembly, prototyping, and manual inspection. Each amplifier is designed for conventional closed-loop operation using external feedback components. The combination of low quiescent current and rail-to-rail signal handling allows the device to operate close to its supply limits, reducing the required headroom in portable systems. Configuration resistors and compensation networks should be selected for the intended closed-loop gain because the bandwidth available for stable operation depends on that gain. Typical uses include low-frequency sensor conditioning, microphone preamplification, current-to-voltage conversion, active filtering, and four-channel buffering. The four independent channels can also implement common analog functions such as two differential amplifiers, two comparators with suitable output saturation limits, or instrumentation-style signal conditioning. The shutdown pin is useful when battery life is more important than maintaining an active analog state. For PCB design, keep input, feedback, output, and decoupling paths short, and place the power-supply bypass capacitor close to the device. Check input and output swing limits against the actual load and supply voltage. Because each channel is independent, unused amplifiers should be configured in a stable state rather than left with floating inputs. This product data combines the manufacturer-family characteristics, package information, sourcing metadata, and engineering design guidance to support amplifier selection, PCB implementation, and replacement planning for the TLV2455CN.

RFQ צור קשר
TLV2455IN - 4-Channel 6V 220kHz RRIO Op Amp | Texas Instruments
TLV2455IN

TLV2455IN - 4-Channel 6V 220kHz RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2455IN is a four-channel, rail-to-rail input/output operational amplifier with shutdown, a 6 V supply rating, 220 kHz gain-bandwidth product, and low 23 µA quiescent current per channel. The device is packaged in a 16-pin through-hole DIP and is intended for low-voltage instrumentation, signal-conditioning, filtering, and portable analog systems. Its four amplifiers share one package, allowing compact implementation of multi-channel signal chains without using four separate monolithic packages. An operational amplifier is an analog signal-processing IC that compares its inverting and non-inverting inputs and amplifies the voltage difference between them. The TLV2455IN belongs to the low-dropout linear-amplifier family of voltage-feedback operational amplifiers, combining rail-to-rail input and output operation with low supply current. Rail-to-rail input capability supports sensing signals near the supply rails, while rail-to-rail output allows the output voltage to approach either supply limit within the device's operating limits. The principal electrical characteristics are a 220 kHz gain-bandwidth product, 23 µA typical quiescent current per channel, a 6 V supply rating, rail-to-rail input and output operation, a shutdown function, and 20 µV typical input offset voltage. The 220 kHz bandwidth supports moderate-frequency amplification and active filtering, while the four-channel configuration is useful for sensor buffers, differential stages, and multi-axis signal processing. Each amplifier can be configured with external resistors for noninverting, inverting, differential, filtering, or gain-control circuits. The low quiescent current is particularly valuable in battery-powered equipment where every amplifier channel contributes continuously to system power consumption. The shutdown feature can also reduce consumption when the analog section is not required, provided the enable logic and supply states meet the manufacturer's operating requirements. Typical uses include portable instrumentation, low-voltage sensor interfaces, audio and control-signal conditioning, active filters, and four-channel acquisition front ends. When designing the board, place each amplifier's feedback components close to its pins, keep input and output traces short, provide suitable bypassing at the supply pins, and avoid placing sensitive high-impedance inputs next to switching or high-current return paths. This product page combines manufacturer specifications, an electrically equivalent same-package option, application guidance, and package-aware design considerations. It helps engineers distinguish the TLV2455IN's shutdown-enabled function from other quad amplifier variants and plan a direct replacement without changing the 16-pin DIP footprint.

RFQ צור קשר
TLV2460CD - 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments
TLV2460CD

TLV2460CD - 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments

The Texas Instruments TLV2460CD is a single, 6.4 MHz rail-to-rail input/output operational amplifier with shutdown, supplied in an 8-SOIC package. It is designed for low-voltage signal-conditioning systems requiring input and output swing close to the supply rails, a 6 V maximum supply rating, and a shutdown function for controlled power management. A rail-to-rail input/output operational amplifier is a voltage-feedback amplifier whose input common-mode and output voltage capabilities extend toward the positive and negative supply rails. This rail-to-rail behavior is useful in battery-powered and portable systems where the usable signal range is close to the available supply voltage. The TLV2460 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. The TLV2460CD provides one amplifier circuit, 6.4 MHz gain-bandwidth performance, low-power operation, and rail-to-rail input and output characteristics. Its 6 V maximum supply voltage supports low-voltage designs, while the shutdown control can reduce power consumption when the signal chain does not need to remain active. The 8-SOIC package provides a conventional surface-mount format with 0.154-inch body width and 3.90 mm width. Its 6.4 MHz bandwidth makes the device suitable for general-purpose voltage amplification, buffering, active filtering, and low-to-moderate-frequency signal conditioning. Rail-to-rail input operation permits sensing signals near either supply rail, while rail-to-rail output capability improves usable output range in low-voltage systems. The manufacturer identifies the device as a low-power RRIO amplifier with shutdown for general-purpose instrumentation applications. Typical uses include portable sensor interfaces, low-voltage analog signal chains, active filters, industrial measurement circuits, and embedded control systems. In a portable sensor interface, the amplifier can condition a sensor signal close to a low-voltage rail. In an active filter, its 6.4 MHz bandwidth provides frequency headroom above the intended passband. The shutdown pin is useful when the amplifier must be disabled during idle periods. Designers should verify supply range, input common-mode limits, output swing, stability, and shutdown logic for the operating conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because the exact pin names, electrical limits, and capacitor recommendations are not included in the product-page summary, use the manufacturer datasheet for final schematic and layout decisions. This page organizes the TLV2460CD device information, verified drop-in alternatives, application guidance, package details, and comparison criteria into one engineering-focused reference. It also identifies which technical details require confirmation from the manufacturer datasheet before layout, qualification, or production release.

RFQ צור קשר
TLV2460CP - 6.4MHz RRIO Op Amp with Shutdown | TI
TLV2460CP

TLV2460CP - 6.4MHz RRIO Op Amp with Shutdown | TI

Texas Instruments TLV2460CP is a single, low-power, rail-to-rail input/output operational amplifier with shutdown, 6.4 MHz gain-bandwidth product, and a 6 V maximum supply rating. The device is packaged in an 8-pin PDIP and is intended for portable instrumentation, buffering, and general-purpose signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify a differential input voltage. The TLV2460CP belongs to the rail-to-rail input/output amplifier category, allowing its input and output operation to extend toward the supply rails. Within the broader hierarchy, it is an operational amplifier, analog amplifier IC, and signal-conditioning semiconductor designed for low-voltage systems. The TLV2460CP combines a single amplifier with rail-to-rail input and output capability, a 6.4 MHz gain-bandwidth product, and shutdown support. Its shutdown control can place the amplifier in a low-power state when signal processing is not required, helping reduce system consumption in portable equipment. The device is identified as a single 6 V, 6.4 MHz RRIO amplifier with shutdown by the Texas Instruments product page. Its rail-to-rail input characteristic is important for signal sources whose voltage swings approach either supply rail, while rail-to-rail output improves voltage headroom when driving a load at low supply voltages. The 6.4 MHz bandwidth supports applications requiring higher closed-loop bandwidth than a general-purpose low-frequency amplifier, although stable operation still depends on the selected feedback topology, noise gain, output loading, and compensation network. Typical uses include low-voltage sensor conditioning, portable test equipment, audio and communication signal paths, instrumentation buffering, and active filtering. The shutdown function is useful in battery-powered or intermittently operated systems where the amplifier must be disabled between measurement intervals. Rail-to-rail operation also makes the device applicable to systems in which the signal range occupies a substantial portion of the available supply voltage. Designers should verify the shutdown-pin polarity, input common-mode limits, output swing, stability requirements, and recommended capacitor values in the manufacturer datasheet before finalizing a PCB. Because this is an 8-pin PDIP rather than a surface-mount package, it is best suited to designs that prioritize easy inspection, prototyping, or through-hole assembly over compact board area. This page organizes the TLV2460CP identity, package, verified electrical highlights, sourcing questions, compatible family options, comparison parameters, and practical design guidance into one engineering reference. It also distinguishes confirmed manufacturer information from characteristics that require confirmation in the complete datasheet before production release.

RFQ צור קשר
TLV2460ID - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments
TLV2460ID

TLV2460ID - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments

The Texas Instruments TLV2460ID is a single, 6 V, 6.4 MHz rail-to-rail input and output operational amplifier with shutdown capability, packaged in an 8-pin SOIC. It is designed for low-power, general-purpose signal conditioning and provides rail-to-rail input and output operation for portable instrumentation, sensor interfaces, audio signal paths, and embedded analog systems. The TLV2460ID supports an operating temperature range of -40°C to +125°C. An operational amplifier is an analog active device that uses high open-loop gain to amplify the difference between two input voltages. Rail-to-rail input capability allows the input common-mode voltage to approach the supply rails, while rail-to-rail output capability improves output swing in low-voltage systems. The TLV2460 belongs to the broader hierarchy of integrated circuits, analog amplifiers, voltage amplifiers, and general-purpose operational amplifiers. The main differentiating feature of the TLV2460ID is its shutdown function, which allows the circuit to reduce operating current when the analog section is not required. Its 6.4 MHz gain-bandwidth product supports applications that need higher signal bandwidth than a basic micropower amplifier. The device is identified as a single amplifier with one shutdown control, making it suitable for designs requiring one analog channel rather than a dual or quad amplifier. The TLV2460ID is used where a designer needs a compact, low-power amplifier with flexible input and output range. It can interface with sensors, buffer voltage references, perform active filtering, amplify audio or control signals, and condition inputs for higher-resolution converters. Its rail-to-rail behavior is particularly useful in systems powered from a single low-voltage rail, where conventional input and output ranges would leave insufficient headroom. When using the TLV2460ID, connect bypass capacitors close to the supply pins and keep feedback-resistor networks compact to minimize parasitic capacitance and instability risk. The shutdown pin should be driven with a defined logic level whenever the amplifier state matters. Verify input and output signal limits against the supply voltage, especially during startup, shutdown transitions, and transients. The 8-pin SOIC package supports standard surface-mount assembly and hand-soldering workflows. This page combines manufacturer and distributor references with drop-in replacement guidance, parameter comparisons, application notes, and practical PCB considerations for engineers evaluating the TLV2460ID in low-voltage analog designs.

RFQ צור קשר
TLV2460IP - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments
TLV2460IP

TLV2460IP - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments

Texas Instruments TLV2460IP is a single-amplifier, rail-to-rail input/output operational amplifier with a 6 V supply rating, 6.4 MHz gain-bandwidth product, and shutdown capability, housed in an 8-pin PDIP package. The device combines a 1.6 V/us slew rate with input bias current of 14 nA and an input offset voltage of 500 uV, making it suitable for portable, low-voltage signal-conditioning systems. An operational amplifier is a voltage-controlled differential amplifier used to amplify errors and control feedback loops. The TLV2460 belongs to the rail-to-rail input/output amplifier category, with input common-mode range extending beyond the supply rails and output swing approaching both rails. This places it within the amplifier IC hierarchy of signal-chain and analog-conditioning components used in portable instrumentation, sensor interfaces, audio paths, and low-voltage industrial systems. The 6.4 MHz gain-bandwidth product supports higher closed-loop bandwidth than slower general-purpose amplifiers, while the 1.6 V/us slew rate improves response to fast voltage changes. Rail-to-rail input behavior increases usable signal range in low-voltage systems, and rail-to-rail output swing provides additional headroom. A shutdown function can reduce operating demand when the circuit is not active, although the exact shutdown timing and current values should be confirmed in the manufacturer datasheet. The TLV2460IP uses a conventional single-supply operational-amplifier architecture intended for low-voltage operation. Its 500 uV offset specification is relevant to precision DC conditioning, while the 14 nA bias current limits input-amplifier loading on high-impedance sources. Designers must still account for input bias-current error, offset drift, output-current limits, noise, and stability when applying it around sensors, filters, or feedback networks. Typical uses include portable battery-powered measurement systems, low-voltage sensor interfaces, audio signal conditioning, general-purpose analog filters, and industrial control modules. In each case, the 6 V maximum supply and rail-to-rail behavior are useful for compact systems where the signal can approach the available supply range. The PDIP package also favors through-hole assembly, prototyping, and designs that require a socketable amplifier. For stable operation, place input and feedback components close to the amplifier, decouple the supply pins, and verify output settling before clocked or measurement systems begin acquisition. Use shutdown only after checking timing relationships elsewhere in the circuit, because shutting down the amplifier during a conversion can invalidate the measurement. This page combines the manufacturer's device description with practical application guidance, drop-in family options, comparison parameters, and design guidance. It emphasizes verified package compatibility and practical trade-offs rather than treating differently packaged amplifier variants as direct replacements.

RFQ צור קשר
TLV2461CP - 6.4MHz RRIO Op Amp | Texas Instruments
TLV2461CP

TLV2461CP - 6.4MHz RRIO Op Amp | Texas Instruments

Texas Instruments TLV2461CP is a single-circuit, 6 V, 6.4 MHz rail-to-rail input/output operational amplifier packaged in an 8-pin PDIP. It combines a 6.4 MHz gain-bandwidth product with rail-to-rail input and output capability, making it suitable for portable instrumentation, low-voltage signal conditioning, and general-purpose analog systems. An operational amplifier is an active analog circuit block that amplifies the voltage difference between its inverting and non-inverting inputs. Rail-to-rail input operation allows signals to approach the supply rails, while rail-to-rail output operation gives designers additional output swing near the limits of the available supply voltage. In the broader device hierarchy, the TLV2461CP belongs to the operational-amplifier and analog-signal-chain categories rather than the digital IC or power-management categories. The TLV2461 family is identified by Texas Instruments as a family of low-power, rail-to-rail input/output operational amplifiers with shutdown capability. The TLV2461CP provides one amplifier circuit in a through-hole PDIP package, which supports prototyping, educational platforms, and industrial assemblies where leaded components are preferred. Its stated 6.4 MHz bandwidth provides substantially more signal-path flexibility than low-frequency general-purpose amplifiers. A 6 V maximum supply rating supports operation from low-voltage portable systems, while the single-amplifier configuration avoids unused circuitry in applications needing one signal channel. Rail-to-rail inputs are useful when sensing small signals near a lower supply rail, and rail-to-rail outputs help preserve dynamic range when driving a subsequent analog stage. The 8-pin PDIP format also simplifies socket-based construction and hand-soldered prototype assembly compared with a fine-pitch surface-mount package. Typical uses include low-voltage sensor interfaces, portable measurement equipment, audio and communication signal conditioning, buffer stages, and active filtering. In a portable sensor circuit, the amplifier can sit close to the sensor and process a weak bipolar or unipolar signal before further conditioning. In an active-filter design, its 6.4 MHz bandwidth provides the transition-frequency and phase-margin margin needed for moderate-bandwidth filtering stages. Design should account for common-mode range, output swing, input bias current, noise, stability, and load capability under the actual supply voltage. Decoupling capacitors should be placed close to the supply pins, and signal routing should minimize parasitic capacitance. Because the TLV2461CP is a leaded PDIP device, board designers should also preserve adequate hole spacing and verify the orientation mark before soldering. This product page combines the manufacturer identity, ordering package, primary electrical headline, lifecycle context, sourcing guidance, and practical design considerations. It also distinguishes genuine same-package alternatives from parts that merely perform a similar function, helping engineers evaluate replacement decisions without assuming that package compatibility alone guarantees equivalent performance.

RFQ צור קשר
TLV2461ID - 6V 6.4MHz RRIO Op Amp | Texas Instruments
TLV2461ID

TLV2461ID - 6V 6.4MHz RRIO Op Amp | Texas Instruments

Texas Instruments TLV2461ID is a single-circuit operational amplifier designed for low-power, rail-to-rail input and output operation from a 2.7 V to 6 V supply. Its 6.4 MHz gain-bandwidth product, 80 mA output capability, 66 dB instrumentation gain, and 0.075 µA quiescent current make it suitable for portable instrumentation, sensor interfaces, battery-powered equipment, and general signal-conditioning systems. The device is packaged in an 8-pin SOIC. An operational amplifier is an analog IC that amplifies the voltage difference between its differential inputs. A rail-to-rail input/output, or RRIO, amplifier can accept input signals near the positive and negative supply rails and produce output swings close to those rails. This makes the TLV2461 useful in systems whose signal range would exceed the usable input or output range of a conventional amplifier tied closely to its supply rails. The TLV2461ID combines a 6.4 MHz gain-bandwidth product with a low 0.075 µA quiescent current. According to the Texas Instruments product page, it is a single amplifier operating from 2.7 V to 6 V. Its input bias current of 1.3 nA is suited to high-impedance sources, while the listed 80 mA per-channel output current provides useful drive capability for typical analog stages. The amplifier also supports input and output operation across the supply rails. With a reported instrumentation gain of 66 dB, the device can be used in instrumentation and measurement circuits requiring moderate signal amplification. Its 6.4 MHz bandwidth supports higher-frequency feedback networks than a low-frequency precision amplifier. The SOIC-8 package is suitable for conventional PCB assembly, and the single-amplifier configuration provides a straightforward implementation for buffer, amplifier, comparator-style, and general-purpose analog applications. Typical applications include portable sensor conditioning, battery-operated measurement instruments, industrial low-power interfaces, audio and communication control paths, precision current-voltage conversion, and low-leakage photodiode front ends. The 1.3 nA input bias current is particularly relevant when the source impedance is high enough that amplifier input current materially changes the measured voltage. Designers should verify signal amplitude, output swing, input common-mode range, noise, and stability at the intended gain. Decoupling capacitors should be placed close to the supply pins, while high-impedance input nodes require short traces and guarded layouts to reduce leakage and interference pickup. This page combines the Texas Instruments device specifications with package guidance, application-oriented engineering notes, and same-package replacement options for engineers planning a TLV2461ID-based analog circuit.

RFQ צור קשר
TLV2461IP - 6V RRIO 6.4MHz Op Amp | Texas Instruments
TLV2461IP

TLV2461IP - 6V RRIO 6.4MHz Op Amp | Texas Instruments

The Texas Instruments TLV2461IP is a single, 6 V, 6.4 MHz rail-to-rail input/output operational amplifier packaged in an 8-pin plastic DIP. It combines a low-noise amplifier core with rail-to-rail input and output stages for portable instrumentation, sensor signal conditioning, and low-voltage analog systems. The TLV2461IP provides one amplifier circuit in an 8-PDIP package. A rail-to-rail input/output operational amplifier is an analog signal-conditioning IC whose input common-mode range and output swing extend toward the positive and negative supply rails. This capability is useful when a signal approaches either supply limit, where a conventional fixed-range amplifier would clip or become nonlinear. Within the broader hierarchy, the TLV2461IP is an operational amplifier, an analog amplifier IC, and a semiconductor for low-voltage power management and signal processing. The principal device characteristics are a 6 V supply rating, 6.4 MHz gain-bandwidth product, and rail-to-rail input/output operation. The single-amplifier configuration supports space-efficient designs where one analog channel is sufficient. Its 8-PDIP construction also facilitates prototyping, educational circuits, and through-hole industrial assemblies where surface-mount rework would be inconvenient. The TLV2461 family targets portable and low-voltage applications where rail-to-rail signal handling is important. According to the Texas Instruments TLV2461 product information, the device is specified as a single 6 V, 6.4 MHz RRIO operational amplifier. Its architecture places the amplifier in the signal-conditioning hierarchy between a sensor or source and an ADC, transducer driver, or analog processing stage. Exact current, noise, offset, and temperature specifications should be confirmed in the manufacturer datasheet for the selected operating conditions. Typical uses include portable measurement systems, battery-powered sensor interfaces, low-voltage audio paths, industrial controls, and general-purpose analog filtering. In a sensor-conditioning circuit, the amplifier can accept signals near the supply rails while presenting low-versus-high input impedance to the source. In an active filter or level-shifting stage, rail-to-rail output behavior can reduce clipping when the calculated output approaches the available supply range. Designers should review the pin-description table, recommended operating conditions, electrical characteristics, and application information in the manufacturer datasheet before layout. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be handled according to the datasheet guidance rather than left floating when the configuration permits it. This page combines the TLV2461IP device identity, package information, verified manufacturer and distributor references, application guidance, and same-footprint alternatives into a focused engineering selection resource. It helps buyers evaluate the TLV2461IP for the Texas Instruments TLV2461 6 V RRIO operational-amplifier family while keeping board-level compatibility and application fit in view.

RFQ צור קשר
TLV2462CD - Dual 6.4MHz RRIO Op Amp | Texas Instruments
TLV2462CD

TLV2462CD - Dual 6.4MHz RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2462CD is a dual, low-power, rail-to-rail input/output operational amplifier with a 6.4 MHz gain-bandwidth product, 1.6 V/µs slew rate, and 80 mA output-drive capability in an 8-pin SOIC package. The device operates from a 2.7 V to 5.5 V supply and consumes approximately 500 µA per amplifier channel, making it suitable for portable and low-voltage systems. An operational amplifier is an analog signal-conditioning IC that provides high open-loop gain and negative feedback to amplify or buffer a voltage signal. The TLV2462 belongs to the RRIO operational-amplifier family, where RRIO denotes rail-to-rail input and rail-to-rail output. This places the device in the broader hierarchy of analog ICs, signal-chain ICs, amplifiers, and general-purpose amplifiers. The TLV2462CD provides rail-to-rail input capability for a wide common-mode range and rail-to-rail output swing for improved dynamic range in low-voltage systems. Its 6.4 MHz bandwidth supports higher-frequency signal processing than a conventional micropower amplifier, while the 1.6 V/µs slew rate improves large-signal response. Two amplifiers in one SOIC package reduce board area, and the 500 µA-per-channel supply current supports battery-conscious portable equipment. The dual architecture allows the two channels to perform related or independent functions. Common uses include signal buffering, gain stages, active filtering, sensor-interface amplification, and low-voltage logic-level signal conditioning. Because both amplifiers share a common supply in one package, designers must also account for shared supply current, thermal behavior, ground routing, and channel-to-channel interaction. Typical applications include portable instrumentation, battery-powered monitors, sensor conditioning, audio and communication interfaces, and portable test equipment. The 80 mA output-drive capability is useful when driving moderate loads, while the rail-to-rail output allows useful output voltage to be obtained near the positive and negative supply limits. When designing around the TLV2462CD, verify output-current demand and capacitive-load stability for the selected feedback network. Keep input and feedback traces short, maintain a low-impedance ground reference, and use decoupling close to the supply pins. The available verified material does not provide a complete order-specific pin table, so the pinout field is conservatively marked as unavailable rather than inferred. This page combines verified manufacturer and distributor information with practical selection guidance, application analysis, honest data-gap notes, and same-family drop-in candidates. It distinguishes documented electrical attributes from specifications that require confirmation from the manufacturer datasheet before release to production.

RFQ צור קשר
TLV2462ID - 6.4 MHz Dual RRIO Op Amp | Texas Instruments
TLV2462ID

TLV2462ID - 6.4 MHz Dual RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2462ID is a dual, low-power, rail-to-rail input/output operational amplifier with a 6.4 MHz gain-bandwidth product, 1.6 V/µs slew rate, and operation from a single 2.7 V to 6 V supply in an 8-pin SOIC package. The TLV2462ID uses one amplifier per package and is designed for portable and general-purpose signal-conditioning applications requiring low power, wide bandwidth, and rail-to-rail operation. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose closed-loop behavior is determined primarily by external feedback components. The rail-to-rail input and output architecture places the TLV2462ID within the low-voltage power-management hierarchy as an analog signal-conditioning IC. It can operate on a single supply or with dual supplies, making it useful where signals occur near either supply rail. The TLV2462 family provides a 6.4 MHz gain-bandwidth product and 1.6 V/µs slew rate. Its 6 V maximum supply voltage supports low-voltage portable equipment, while the dual configuration reduces the number of packages required for stereo, differential, filtering, or instrumentation circuits. The rail-to-rail input common-mode range and rail-to-rail output capability help preserve signal headroom in compact systems. The TLV2462ID is offered in an 8-pin Small Outline Integrated Circuit package. The manufacturer describes the TLV2462 as a low-power dual operational amplifier intended for portable applications. Its combination of moderate speed, low-voltage operation, and dual-channel integration supports signal buffering, sensor conditioning, audio paths, and general-purpose analog processing when the system does not require a higher-speed or lower-noise precision amplifier. Typical applications include portable sensor interfaces, low-voltage audio signal conditioning, battery-powered measurement systems, active filters, and dual-rail or single-rail analog front ends. Designers should verify the complete electrical limits, common-mode behavior, output swing, shutdown configuration, stability requirements, and package details against the manufacturer datasheet before production release, particularly where input signals approach the supply rails. For low-noise or high-impedance sensor interfaces, compare the TLV2462ID against a precision low-noise amplifier because its 6.4 MHz bandwidth favors speed and general-purpose signal handling. Maintain adequate bypass capacitance near the supply pins and keep sensitive input and feedback paths short to minimize parasitic pickup, oscillation, and sensitivity to board-level interference. This product record combines the verified 6.4 MHz bandwidth, 1.6 V/µs slew rate, 6 V supply limit, 8-pin SOIC construction, operating-temperature range, pricing floor, and distributor availability with practical design guidance. It also distinguishes directly identified ordering variants from true drop-in alternatives and flags electrical parameters that still require confirmation from the manufacturer datasheet.

RFQ צור קשר
TLV2462QD - Dual RRIO 6.4MHz Op Amp | Texas Instruments
TLV2462QD

TLV2462QD - Dual RRIO 6.4MHz Op Amp | Texas Instruments

Texas Instruments TLV2462QD is a dual, low-power operational amplifier with rail-to-rail input and output capability, a 6.4 MHz gain-bandwidth product, and a 6 V maximum supply rating. The device is packaged in an 8-pin SOIC and is designed for portable applications where two amplifier channels are needed within a compact, low-power circuit. An operational amplifier is a voltage-gain component used to amplify small signals, buffer voltage sources, compare analog thresholds, and support feedback-based signal conditioning. The TLV2462 belongs to the operational-amplifier, analog-signal-conditioning, and power-management-IC hierarchy. Rail-to-rail input capability allows the amplifier to accept input voltages near the supply rails, while rail-to-rail output capability supports operation with limited output-voltage headroom. The TLV2462QD provides two amplifier channels in one package, reducing board area compared with separate single-channel devices. Its 6.4 MHz gain-bandwidth product supports signal paths requiring moderate bandwidth, and its specified 80 mA output-drive capability is useful for driving moderate loads. The manufacturer describes the family as low power, with a quoted supply current of 500 µA per channel, making it applicable to portable instrumentation and other compact battery-operated systems. Both channels share the same supply pins, but each channel can be configured independently as an amplifier, buffer, comparator, or active-filter element. The common package and dual-channel organization also simplify power distribution and reduce the number of external components required for dual-signal conditioning. Configuration depends on the feedback network, input impedance, source impedance, output loading, and required stability. Typical uses include portable sensor interfaces, low-level analog signal amplification, voltage buffering, threshold detection, audio preamplification, and general-purpose analog conditioning. The 6 V rating supports low-voltage systems, while the 8-pin SOIC package allows conventional surface-mount assembly. Care is still required when operating near the supply rails, driving capacitive loads, or selecting feedback values for stable closed-loop response. For design planning, verify the complete electrical limits and pin assignments in the manufacturer datasheet before layout release. Decoupling capacitors should be placed close to the supply pins, input and output routing should minimize parasitic capacitance, and unused amplifier inputs must be tied to a defined potential rather than left floating. This page combines package, performance, application, and replacement guidance to support early design decisions.

RFQ צור קשר
TLV2464CD - Quad 6.4MHz RRIO Op Amp, 6V, SOIC-14 | Texas Instruments
TLV2464CD

TLV2464CD - Quad 6.4MHz RRIO Op Amp, 6V, SOIC-14 | Texas Instruments

The Texas Instruments TLV2464CD is a quad, general-purpose, rail-to-rail input/output (RRIO) CMOS operational amplifier with a 6.4 MHz gain-bandwidth product, a 1.6 V/µs slew rate, and 2.7 V to 6 V single-supply operation, housed in a 14-pin SOIC (D) package rated for 0 °C to +70 °C. An operational amplifier is an analog building block that amplifies the difference between two input voltages. A rail-to-rail input/output amplifier is a specific class whose input common-mode range and output swing extend to the supply rails, so the signal can be processed without clipping even when it approaches the limits of the supply. TLV2464 belongs to TI's family of low-power rail-to-rail input/output operational amplifiers, and the quad configuration integrates four amplifiers in one package, reducing board area and per-channel cost in multi-channel designs. Key features include 6.4 MHz unity-gain bandwidth for a wide closed-loop bandwidth at moderate gains, 1.6 V/µs slew rate for full-scale step response, rail-to-rail inputs that extend beyond the supply rails for maximum dynamic range in low-voltage systems, and rail-to-rail outputs that swing close to both rails. The low-power CMOS design targets portable, battery-powered instrumentation where supply current matters as much as bandwidth. Technically, the device pairs rail-to-rail input stages with a CMOS output stage capable of driving capacitive and resistive loads close to the supply rails. Because the amplifiers are specified from 2.7 V up to 6 V, the same part covers 3 V and 5 V systems. With a 6.4 MHz gain-bandwidth product, closed-loop gain of 10 still yields roughly 640 kHz of usable bandwidth, while the 1.6 V/µs slew rate sets the large-signal limit on fast edges. Typical applications include low-cost data acquisition and sensor signal conditioning, portable medical and instrumentation front ends, audio and communication line-level stages, active filtering, and battery-powered portable equipment where four channels are needed on a single board. When designing with the TLV2464CD, keep the input common-mode voltage inside the rated range, use decoupling capacitors close to the supply pins, and confirm that the load impedance and capacitive loading stay within the stability envelope described in the manufacturer datasheet. Driving heavy capacitive loads directly at high gain can require an isolation resistor. This page consolidates the manufacturer device description, distributor categorization, and cross-reference findings into one engineering view, adding practical design notes, pin-level guidance, and a parameter-by-parameter comparison that the raw datasheet pages do not present side by side.

RFQ צור קשר
TLV2464CN - Quad 6V RRIO Op Amp | Texas Instruments
TLV2464CN

TLV2464CN - Quad 6V RRIO Op Amp | Texas Instruments

Texas Instruments TLV2464CN is a quad, 6 V, 6.4 MHz, rail-to-rail input and output operational amplifier packaged in a 14-pin PDIP. The four integrated amplifiers support low-power portable systems while providing approximately 500 µA of supply current per channel, 80 mA of output-drive capability, and a 6.4 MHz gain-bandwidth product. These specifications place the TLV2464CN in the low-power RRIO operational-amplifier category. A rail-to-rail input/output operational amplifier is a voltage-feedback amplifier whose input common-mode range and output swing can approach its supply rails. The TLV2464 family uses this capability to process signals near the limits of a low-voltage supply. Its role within the hierarchy is operational amplifier → rail-to-rail amplifier → low-power analog signal-conditioning IC, making it useful where amplifier channels must operate from limited supply voltage and headroom is constrained. Four amplifiers are integrated into one TLV2464CN package, reducing the number of packages required for multichannel analog designs. The 6.4 MHz gain-bandwidth product supports higher-frequency signal paths than a conventional low-power slow-slew-rate amplifier. Rail-to-rail input operation helps preserve signal integrity when common-mode input levels approach either supply rail, while rail-to-rail output operation increases usable output range at low supply voltages. The approximately 500 µA per-channel supply current and 80 mA output-drive capability provide a practical balance between power efficiency and drive capability. The 80 mA figure is relevant when the amplifier must charge external capacitive loads, drive ADC input networks, or operate with resistive loading. Actual usable bandwidth and output amplitude depend on closed-loop gain, load impedance, output voltage, and the device’s stability configuration. Typical uses include portable instrumentation, sensor-signal conditioning, battery-powered measurement systems, low-voltage analog front ends, communications equipment, and general-purpose buffering. Multiple channels can process related signals, such as sensor outputs, transducer feedback, analog monitoring nodes, or small-signal conditioning stages without requiring four separate amplifier packages. When designing around the TLV2464CN, verify the complete datasheet for input bias current, offset voltage, input protection behavior, output swing, and stability before fixing capacitor values or gain settings. Preserve the required bypass capacitance close to the supply pins and route feedback paths away from high-impedance input nodes. Consider whether the 6 V maximum supply and low-power operating point satisfy the system’s noise, slew-rate, and load requirements. This page consolidates verified manufacturer and distributor information, observed pricing, same-package alternatives, and practical design guidance for engineers evaluating the TLV2464CN. It also distinguishes documented electrical characteristics from values that require confirmation in the complete manufacturer datasheet.

RFQ צור קשר
TLV2464ID - Quad 6V 6.4MHz RRIO Op Amp | Texas Instruments
TLV2464ID

TLV2464ID - Quad 6V 6.4MHz RRIO Op Amp | Texas Instruments

Texas Instruments TLV2464ID is a quad, 6 V, 6.4 MHz rail-to-rail input/output operational amplifier packaged in a 14-pin SOIC. The device provides four amplifier channels, 80 mA output-drive capability, and approximately 500 uA of supply current per channel. Its low-power design and rail-to-rail input/output architecture make it suitable for portable and low-voltage systems requiring four signal-conditioning channels in one package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. The TLV2464 belongs to the operational-amplifier hierarchy within analog ICs and combines high gain, common-mode input range, output swing capability, and output drive in a compact quad package. The rail-to-rail input stage supports signals approaching the supply rails, while the rail-to-rail output stage allows the output voltage to swing closer to both rails than a conventional non-RRIO amplifier. The TLV2464 family is specified for operation from a 6 V supply and provides a gain-bandwidth product of 6.4 MHz. Each channel is designed for low-power operation, with the verified family data indicating approximately 500 uA of supply current per channel. The listed 80 mA output-drive capability supports higher-capacitance loads and faster transitions than a lightly loaded general-purpose amplifier can provide. These features are relevant in filtering, buffering, level translation, and sensor-interface circuits. The input common-mode voltage range extends beyond the supply rails, increasing usable signal range in low-voltage systems. Rail-to-rail output swing improves signal utilization where conventional amplifier headroom would clip the waveform. Four independent channels reduce component count in multichannel analog front ends, although each amplifier still requires suitable bypassing and stable feedback compensation. The available TLV2464ID package is a surface-mount 14-pin SOIC rated from -40 C to +85 C. Typical uses include portable instrumentation, low-voltage sensor conditioning, active filters, audio and communication interfaces, control loops, and general-purpose buffering. The 6.4 MHz bandwidth is appropriate for moderate-frequency precision signal paths rather than high-speed video or RF applications. When all four channels do not need identical configurations, unused amplifier inputs should be tied to a defined potential close to the common-mode operating point rather than left floating. PCB design should place the supply bypass capacitor close to the device and preserve a low-impedance ground return. Decoupling requirements, stability criteria, input/output capacitance limits, and shutdown-pin details must be confirmed in the manufacturer datasheet because those values were not included in the supplied search data. Designers should also verify source and sink output-current limits against the actual load, especially when driving capacitive or nonlinear loads. This page consolidates the verified manufacturer and distributor information, separates known TLV2464ID characteristics from unavailable parameters, and documents same-brand drop-in options without presenting them as verified cross-brand substitutes. It also provides application guidance, comparison fields, and design cautions that help engineers evaluate this quad amplifier for an existing 14-pin SOIC design as of 2026-10-30.

RFQ צור קשר
TLV2465ID - Quad 5.2MHz RRIO Op Amp | Texas Instruments
TLV2465ID

TLV2465ID - Quad 5.2MHz RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2465ID is a quad, low-power, rail-to-rail input/output operational amplifier with a 6 V supply rating, 5.2 MHz gain-bandwidth product, and 16-SOIC package. The family is designed for portable and low-voltage systems where four amplifiers are needed in a compact footprint. Its rail-to-rail input and output behavior supports signal conditioning close to the supply limits, while the low-power architecture targets battery-powered equipment and portable instrumentation. According to the Texas Instruments TLV2465 product page, the device is a quad, 6 V operational amplifier, and the product-page description identifies the TLV2465 family as a low-power rail-to-rail input/output amplifier family. An operational amplifier is an analog integrated circuit that uses differential feedback to amplify the difference between two input voltages. The TLV2465ID belongs to the operational-amplifier hierarchy, also called op amp or voltage-feedback amplifier, within analog and mixed-signal integrated circuits. A quad package contains four amplifiers in one IC, reducing board area and simplifying multi-channel designs. Rail-to-rail input means the input common-mode range extends beyond the conventional supply-rail limits, while rail-to-rail output allows the output voltage to approach either supply rail under suitable load and frequency conditions. The main electrical characteristics include a 5.2 MHz gain-bandwidth product for the TLV2465 family, a 1.35 V to 6 V operating supply range as indicated by the distributor product description, and rail-to-rail input and output operation. The family is also described as supporting shutdown operation in the TLV246x family documentation. These characteristics make the device suitable for sensor interfaces, low-level signal amplification, voltage buffering, active filtering, audio and communication signal conditioning, portable measurement systems, and general-purpose analog signal chains. The 16-SOIC package provides a conventional surface-mount form factor compatible with standard PCB assembly processes. Because the TLV2465ID is a quad amplifier, each channel can perform a different function, such as buffering an ADC input, amplifying a sensor signal, driving an intermediate gain stage, or filtering a control-loop signal. The shared package is useful when a board requires several similar analog functions and when minimizing component count is more important than using the smallest available package. Designers should verify the exact pinout, shutdown behavior, input and output ranges, load capability, and stability requirements against the TLV2465ID manufacturer datasheet before layout release. The SOIC footprint is also a mechanical consideration: the exposed package width and lead pitch must match the PCB land pattern. When selecting this part for a new design, confirm that the required signal bandwidth, supply voltage, output swing, input offset, noise, and channel shutdown requirements match the specific family variant and operating conditions. This page combines the manufacturer product-page description, distributor package and feature information, and practical guidance for evaluating the TLV2465ID. It is intended to help engineers identify whether a quad, low-power, rail-to-rail operational amplifier in a 16-SOIC package is appropriate for portable, industrial, or general-purpose analog designs.

RFQ צור קשר
TLV2470CD - 2.8MHz RRIO Op Amp with Shutdown | Texas Instruments
TLV2470CD

TLV2470CD - 2.8MHz RRIO Op Amp with Shutdown | Texas Instruments

The Texas Instruments TLV2470CD is a single, 6 V, 2.8 MHz, rail-to-rail input and output operational amplifier with shutdown capability, offered in an 8-SOIC package. It combines a 2.7 V to 6 V supply range, 35 mA per channel output capability, 2.5 pA typical input bias current, and 64 dB instrumentation performance. The device is designed for low-power precision signal-conditioning systems where rail-to-rail operation and compact analog integration are important. An operational amplifier, or op amp, is a voltage-gain amplifier that uses external feedback to control closed-loop behavior. Within the semiconductor hierarchy, a rail-to-rail input and output amplifier is an analog amplifier and an integrated circuit. The TLV2470 family combines low-power CMOS operation with broad input and output swing, allowing signals to approach the supply rails without requiring separate negative-rail biasing. This makes it useful for portable, industrial, and instrumentation designs. The TLV2470CD's principal features include 2.8 MHz gain-bandwidth product, approximately 600 uA per channel supply current, rail-to-rail inputs and outputs, shutdown support, and a maximum supply voltage of 6 V. Its 35 mA per channel output capability is suitable for conventional low- and moderate-load analog stages. The 2.5 pA input-bias-current figure helps preserve accuracy when high-impedance sensors or bias networks are involved, while 64 dB instrumentation performance supports precision measurement applications. Technically, the TLV2470 belongs to TI's LiNCMOS operational-amplifier family. Its low quiescent-current operating point makes it especially useful in battery-powered and always-on systems. The combination of a 2.8 MHz bandwidth and approximately 600 uA per channel creates a useful balance between response speed and power efficiency. Because the amplifier operates from as little as 2.7 V, it can also be used in systems whose supply rails fall below the conventional 5 V operating point. Typical applications include portable sensor interfaces, low-current monitoring, buffered sensor conditioning, low-voltage data acquisition, portable test equipment, and power-saving analog subsystems. The TLV2470CD can sit close to sensors to limit signal corruption from board traces and provide gain before a higher-bandwidth ADC or controller. It is also appropriate where shutdown is needed to reduce power during inactive periods. A critical design consideration is the shutdown pin behavior. Pull the shutdown control into its active state when the amplifier must remain off, and ensure the pin is never left floating because the device can consume more current or enter an undefined operating state if the control input is unresolved. Place the amplifier close to high-impedance inputs and use a low-leakage PCB surface to preserve the benefit of the 2.5 pA bias current. This page combines manufacturer specifications, practical application guidance, package information, and clearly qualified drop-in alternatives for engineers evaluating the TLV2470CD for low-voltage analog designs.

RFQ צור קשר
TLV2470CP - 6V, 2.8MHz RRIO Op Amp | Texas Instruments
TLV2470CP

TLV2470CP - 6V, 2.8MHz RRIO Op Amp | Texas Instruments

The Texas Instruments TLV2470CP is a single-rail operational amplifier with a 6 V maximum supply, 2.8 MHz gain-bandwidth product, rail-to-rail input and output operation, and shutdown capability. The device consumes 600 µA per channel and is offered in an 8-pin PDIP package. Its combination of low supply current, short operation, and broad input/output common-mode range supports compact, low-power signal-conditioning systems. A rail-to-rail input/output operational amplifier is an analog amplifier whose input common-mode voltage and output swing can extend toward the positive and negative supply rails. This makes it useful when a sensor, converter, or mixed-signal node operates close to the available supply voltage. Within the broader hierarchy of analog and mixed-signal ICs, the TLV2470CP is a low-voltage CMOS operational amplifier intended for portable, industrial-control, instrumentation, and general-purpose signal-conditioning applications. The TLV2470CP provides 2.8 MHz gain-bandwidth product, rail-to-rail input and output behavior, shutdown support, and approximately 600 µA per channel supply current. The 6 V maximum supply voltage allows operation from low-voltage rails commonly used in portable and embedded equipment. Its low-current operating point is particularly useful for battery-powered monitoring systems, while the 2.8 MHz bandwidth supports moderate-frequency amplification, active filtering, and buffering. The 8-pin PDIP package provides through-hole assembly compatibility and a conventional DIP footprint. The shutdown function can reduce power consumption when the amplifier is not needed, although the complete logic truth table and timing limits must be taken from the manufacturer datasheet. Because operating current and common-mode behavior depend on supply voltage and configuration, the datasheet characteristic curves should be consulted before setting gain, output loading, or input bias assumptions. Typical uses include low-power sensor conditioning, buffered transducers, portable measurement systems, audio input stages, motor or actuator monitoring, and industrial control modules. The amplifier can operate near its supply rails, making it appropriate for systems whose signals occupy much of the available input range. Designers should still verify output swing at the required load and frequency before relying on full rail-to-rail performance. Decoupling, input biasing, and shutdown sequencing are the principal implementation considerations. Place the supply bypass capacitor close to the device, keep sensitive input traces short, and avoid allowing input or output pins to exceed the electrical limits stated in the manufacturer datasheet. This page combines package, electrical, lifecycle, replacement, and application guidance to support initial design selection and PCB planning.

RFQ צור קשר
TLV2470ID - 6V, 2.8MHz RRIO Op Amp | Texas Instruments
TLV2470ID

TLV2470ID - 6V, 2.8MHz RRIO Op Amp | Texas Instruments

Texas Instruments TLV2470ID is a single, low-power, rail-to-rail input/output operational amplifier with shutdown, designed for a 6 V maximum supply and packaged in an 8-pin SOIC. Its three headline characteristics are a 2.8 MHz gain-bandwidth product, 600 µA/channel supply current, and rail-to-rail input and output operation. These characteristics place the TLV2470ID in the operational-amplifier hierarchy of analog ICs, signal-chain ICs, and general-purpose amplifiers. A rail-to-rail input/output operational amplifier is designed to accept input voltages near either supply rail and to produce output voltages close to the positive or negative rail. This is useful in battery-powered and low-voltage systems where usable signal range is limited by the supply voltage. The TLV2470ID combines that input and output range with a shutdown function, allowing a system designer to reduce supply consumption when the amplifier is not needed. The principal performance features include a 2.8 MHz gain-bandwidth product, 600 µA/channel supply current, and a CMOS input stage with a 2.5 pA bias current. Its high-drive capability supports applications where the amplifier must drive a relatively demanding capacitive or resistive load. Rail-to-rail operation also reduces the need for separate input and output range calculations when signals can approach either supply rail. The TLV2470ID belongs to the TLV247x family of single and dual rail-to-rail operational amplifiers. According to the Texas Instruments TLV2470 family description, the family combines low power consumption with comparatively high AC performance for its operating class. The single amplifier in the 8-pin SOIC is suitable for general-purpose precision signal conditioning when a design needs one amplifier rather than a dual package. Typical applications include portable sensor interfaces, low-voltage filter stages, audio input conditioning, battery-powered instrumentation, and general analog signal amplification. The shutdown pin is particularly useful in portable equipment because it can disable the amplifier when the system is inactive. Rail-to-rail inputs help preserve signal fidelity when sensor outputs approach the supply rails. Designers should verify the required output-current capability, capacitive-load stability, input common-mode range, and operating temperature range for the selected ordering code. Place bypass capacitance close to the supply pins and keep feedback routing short because high-speed amplifiers can amplify trace resistance and parasitic capacitance into stability problems. This page combines the TLV2470ID's core technical characteristics with package guidance, sourcing answers, application analysis, and same-family replacement considerations. It also identifies where a direct substitute requires verification of pinout, electrical limits, temperature grade, and shutdown behavior before PCB reuse.

RFQ צור קשר
TLV2470IP - 6V 2.8MHz RRIO Op Amp with Shutdown | TI
TLV2470IP

TLV2470IP - 6V 2.8MHz RRIO Op Amp with Shutdown | TI

The Texas Instruments TLV2470IP is a single-channel, 6 V, 2.8 MHz rail-to-rail input/output operational amplifier with shutdown capability, offered in an 8-pin DIP package. It is designed for general-purpose applications that require low supply current, wide input and output voltage range, and moderate bandwidth. The manufacturer identifies the TLV2470 family as a CMOS rail-to-rail input/output amplifier family that consumes approximately 600 µA per channel while providing 2.8 MHz of gain-bandwidth product. An operational amplifier is an analog integrated circuit that uses differential feedback to amplify the difference between two input voltages. The TLV2470 family belongs to the broader hierarchy of op amp -> operational amplifier -> analog IC -> semiconductor. Rail-to-rail input and output operation allows the amplifier to operate near the supply rails, making it useful in battery-powered instrumentation, sensor interfaces, signal conditioning, audio, and industrial control systems. The principal listed specifications are a 6 V maximum supply voltage, 2.8 MHz gain-bandwidth product, approximately 600 µA per channel supply current, and rail-to-rail input/output capability. The TLV2470 product family also includes a shutdown function, allowing the amplifier to be placed in a low-power state when the system does not require continuous amplification. The exact input offset, output-current, noise, and temperature-range details for the TLV2470IP should be confirmed against the manufacturer datasheet before final design release. The TLV2470IP is specified as an 8-PDIP, or 8-pin dual in-line package, making it suitable for through-hole prototyping and legacy industrial or instrumentation boards where a surface-mount package is not required. Its single amplifier per package permits flexible allocation of analog channels across a larger system. The 2.8 MHz bandwidth is more than adequate for many sensor, buffer, and general signal-conditioning stages, while the approximately 600 µA per-channel consumption supports power-conscious designs. Typical uses include low-voltage sensor conditioning, buffered instrumentation inputs, audio signal paths, portable measurement equipment, and industrial control modules. When designing around this amplifier, verify input and output common-mode limits at the selected supply voltage and confirm the required output swing against the load. Account for shutdown-state behavior, input bias currents, noise, and stability when driving capacitive loads. This page combines the exact manufacturer and distributor identifiers for TLV2470IP with package information, lifecycle context, pricing extraction, cross-reference alternatives, and practical design guidance. Use the manufacturer datasheet as the controlling document for pin assignment, electrical limits, recommended operating conditions, and application-specific design guidance.

RFQ צור קשר