AD628ARMZ - High Common-Mode Difference Amplifier | Analog Devices
MPN: AD628ARMZ ✓ פעילAD628ARMZ סקירה
A difference amplifier measures the voltage between two input nodes while rejecting signals common to both inputs. The AD628 combines this differential function with a high common-mode operating range, broad common-mode rejection across frequency, and a wideband feedback loop. That feedback architecture helps reduce distortion caused by the input capacitance of delta-sigma ADCs and improves measurement accuracy in high-impedance signal chains.
The AD628ARMZ supports programmable gain, allowing the same amplifier to scale small differential signals or reduce high input voltages into an ADC-friendly range. The available data identifies a slew rate of 0.3 V/us, a 600 kHz bandwidth, 75 dB common-mode rejection, 1.5 mV input offset voltage, and 1.5 nA input bias current. These parameters make the device appropriate for precision current and voltage sensing where input offset and bias currents can influence measurement error.
The common-mode range and resistor-divider architecture are particularly relevant to power-supply applications. The manufacturer describes the AD628 as suitable for battery chargers and similar equipment in which high voltages must be scaled into standard control voltages or currents. Its wideband feedback loop also supports systems that require accurate acquisition from capacitive sensor or ADC inputs.
Typical uses include battery-pack monitoring, charger feedback, industrial power rails, high-side current sensing, precision differential measurement, and signal conditioning for single-supply analog-to-digital converters. The 8-MSOP format supports compact PCB layouts, although careful common-mode range checking is essential because the allowable input range is application-dependent.
For a new design, verify supply voltage, input common-mode voltage, gain setting, output swing, and ADC input range before committing to the layout. Keep the differential input route short and symmetric, provide stable reference or gain-setting resistors, and use appropriate input filtering without adding excessive differential capacitance that could reduce phase margin.
This page consolidates the manufacturer’s product description, package information, differential-amplifier characteristics, application guidance, and practical replacement considerations to support faster component selection and PCB planning.
חלופות תחליף ישיר עבור AD628ARMZ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותAD628ARMZ דירוגים מרביים ומאפיינים חשמליים
| אין מפרטים זמינים |
מדריך תצורת פינים של AD628ARMZ standard
תצורת פינים עבור AD628ARMZ (מארזת standard). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור AD628ARMZ.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
AD628ARMZ מתאים עבור 6 יישוםs: Battery-Pack Monitoring, Power-Supply Feedback, High-Side Current Sensing, Single-Supply ADC Signal Conditioning, Precision Industrial Sensing, Battery-Charger Control.
Battery-Pack Monitoring
The AD628ARMZ fits battery monitoring because it measures a small differential cell or divider voltage while operating at a substantially higher common-mode voltage. Its 75 dB common-mode rejection helps suppress changes shared by both input nodes, while the 1.5 mV input offset and 1.5 nA bias current limit error in high-impedance sensing networks. A resistor divider can scale the battery voltage into the amplifier’s legal input range and into a level suitable for a single-supply ADC. The design must verify common-mode limits, supply voltage, gain, and output range over temperature.
מומלץ
Power-Supply Feedback
The AD628ARMZ is suitable for power-supply feedback where a regulated output must be divided down, measured differentially, and presented to an ADC or controller. Its precision difference-amplifier topology rejects common supply movement, while programmable gain permits a useful output range from either large or small differential inputs. The manufacturer specifically identifies battery chargers and similar power-supply equipment as suitable applications. Designers should calculate divider ratios and worst-case gain error, then verify the amplifier’s common-mode and output limits under startup and load-transient conditions.
מומלץ
High-Side Current Sensing
The AD628ARMZ can provide differential amplification around a high-side shunt measurement when the shunt voltage is small relative to its common-mode voltage. The 75 dB common-mode rejection reduces sensitivity to supply and ground movement, while 1.5 mV offset and 1.5 nA bias current help define the achievable low-level measurement accuracy. Its 600 kHz bandwidth covers many slower control and monitoring loops. The PCB should use Kelvin routing for the shunt, minimize parasitic resistance, and keep the amplifier within its specified common-mode range at every operating condition.
מומלץ
Single-Supply ADC Signal Conditioning
The AD628ARMZ is designed for scaling high voltages into standard control voltages or currents suitable for single-supply ADCs. Its wideband feedback loop minimizes distortion caused by the input capacitance of delta-sigma converters, a valuable property when the measurement node includes filtering, protection, or cabling capacitance. Programmable gain supports a compact conversion from a high-voltage input to an ADC-compatible level. Before implementation, confirm that the selected gain, resistor network, and output range prevent clipping and that the ADC input remains within its settling and acquisition requirements.
מומלץ
Precision Industrial Sensing
The AD628ARMZ supports industrial measurement systems that must reject a large common-mode voltage while resolving a smaller sensor differential. Its precision offset voltage of 1.5 mV, bias current of 1.5 nA, and 75 dB common-mode rejection provide concrete limits for designing the analog front end. The 600 kHz bandwidth is suitable for many process and equipment monitoring loops that do not require megahertz signal bandwidth. Place input resistors and protection elements to preserve CMRR, isolate sensitive nodes from leakage, and verify operation over the complete industrial temperature range.
מומלץ
Battery-Charger Control
The AD628ARMZ can form the measurement element of a battery-charger control loop by scaling a high battery or stack voltage into a signal that a controller or ADC can evaluate. Difference-amplifier behavior limits the influence of shared voltage changes, and programmable gain supports different battery-voltage ranges. Analog Devices identifies battery chargers as a representative power-supply application for the resistor-divider approach. A robust design must include input protection, account for resistor tolerance and temperature drift, and keep the amplifier’s common-mode input inside the manufacturer-specified operating region.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור AD628ARMZ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Package | 8-lead MSOP |
| Brand | Analog Devices |
| Amplifier Type | Precision difference amplifier |
| Number of Channels | 1 channel |
| Gain | Programmable gain |
| Common-Mode Rejection | 75 dB |
| Bandwidth | 600 kHz |
| Slew Rate | 0.3 V/us |
| Input Offset Voltage | 1.5 mV |
| Input Bias Current | 1.5 nA |
| RoHS Status | Compliant |
הערות תכנון
Confirm the common-mode input range at the actual resistor-divider node before applying gain or connecting an ADC. A differential amplifier can reject common-mode voltage only while that voltage remains within its legal operating range. Also verify the output swing with the selected supply and gain. Testing only at nominal input voltage can miss clipping during startup, battery disconnection, or maximum-line conditions.
Route the positive and negative measurement inputs as a close, symmetric pair to minimize pickup and parasitic mismatch. Use a ground-plane architecture, place configured gain-setting resistors near their associated pins, and keep the analog return path separate from switching-node currents. For a shunt measurement, use Kelvin connections so copper drops do not appear inside the sensed differential voltage.
Include input filtering for protection and noise control, but verify that differential capacitance does not upset the amplifier’s wideband feedback loop. The AD628’s feedback architecture addresses distortion caused by charging delta-sigma ADC inputs, yet excessive cable or protection capacitance can still alter frequency response. Use a controlled termination network, check settling with the actual ADC, and keep the filter close to the measurement source.
מידע על תאימות
The available part information identifies RoHS 3 compliance, REACH unaffected status, and MSL 1 (unlimited). No vehicle-specific AEC-Q100 qualification, halogen-free declaration, or conflict-minerals declaration was identified for this exact order code.