AD7484BST - 14-Bit 3 MSPS SAR ADC | Analog Devices
MPN: AD7484BST ✓ פעילAD7484BST סקירה
A successive-approximation ADC, or SAR ADC, converts an analog voltage into a digital code through a sequence of internal comparisons. The SAR ADC family occupies the practical middle ground between high-resolution delta-sigma converters and very-high-speed flash converters. Unlike a pipelined ADC, the AD7484 does not introduce pipeline delay. This makes it suitable for systems requiring immediate acquisition results, coherent sampling, or deterministic control-loop timing.
The AD7484BST combines 14-bit resolution with a maximum throughput of 3 MSPS. Its low-noise, wide-bandwidth track-and-hold circuit supports input frequencies above 40 MHz, while the single-input architecture simplifies analog routing. The parallel data interface exposes the conversion result directly to digital logic and is appropriate for systems in which a processor, FPGA, or other parallel data-capture device reads the complete 14-bit result.
Operationally, the converter uses a proprietary algorithmic successive-approximation process rather than a pipeline architecture. Each conversion resolves the sampled input through successive internal decisions, and the result becomes available without a pipeline latency. Designers should still observe the required acquisition and conversion intervals from the manufacturer datasheet when establishing control-loop timing or maximum sampling frequency.
Typical applications include industrial process monitoring, instrumentation, communications receivers, vibration and signal analysis, data-acquisition systems, and control equipment. The 3 MSPS rate supports fast transient capture, while the 14-bit word provides useful resolution for general-purpose analog measurement. Its parallel output also makes it practical in FPGA-based acquisition platforms where converter data can be captured directly on a clock boundary.
The primary design consideration is signal conditioning and interface timing. Place input and reference decoupling close to the device, keep sensitive analog traces short, and use a stable reference arrangement that meets the converter’s accuracy requirements. Digital output timing, clocking, and input acquisition must be designed together because source impedance, sample-and-hold acquisition time, and settling behavior determine the usable input bandwidth.
This page combines the manufacturer’s technical overview, exact-package identification, verified commercial listing information, and practical interface guidance. It also documents drop-in replacement findings and distinguishes the AD7484BSTZ lead-free ordering option from a broader cross-brand replacement search.
חלופות תחליף ישיר עבור AD7484BST — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
AD7484BSTZ
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
AD7484BST דירוגים מרביים ומאפיינים חשמליים
| רזולוציה | 14 bit |
| Maximum Conversion Throughput | 3 MSPS |
| Architecture | Successive approximation register (SAR) |
| Number of Input Channels | 1 channel |
| Input Frequency Capability | Greater than 40 MHz |
| Data Interface | Parallel |
| Pipeline Delay | 0 cycles |
| Technology | CMOS |
| מארז | 48-lead LQFP, 7 mm × 7 mm |
| Package Code | LFQFP |
| Terminal Count | 48 terminals |
| Lead Style | Gull wing |
| Temperature Grade | Industrial |
| Input Supply Voltage | 2.7 V |
| Track-and-Hold Architecture | Low-noise, wide-bandwidth |
| Acquisition Conversion Method | Proprietary algorithmic successive approximation |
מדריך תצורת פינים של AD7484BST lfqfp
תצורת פינים עבור AD7484BST (מארזת lfqfp). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור AD7484BST.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
AD7484BST מתאים עבור 6 יישוםs: Industrial Process Monitoring, FPGA-Based Data Acquisition, Communications Receiver, Vibration and Transient Capture, Precision Instrumentation, Control-System Feedback.
Industrial Process Monitoring
The AD7484BST fits fast process-monitoring systems that sample analog sensor or transducer signals while retaining 14-bit resolution. Its 3 MSPS throughput provides temporal headroom for capturing transients, and the wide-bandwidth track-and-hold can accept input frequencies exceeding 40 MHz when the front-end and acquisition network are designed accordingly. A typical arrangement places a buffered sensor signal into the ADC input, uses the manufacturer-recommended reference and decoupling network, and sends the parallel result to an FPGA or embedded controller. The absence of pipeline delay makes acquisition timing easier to relate to the sampled event.
מומלץ
FPGA-Based Data Acquisition
The AD7484BST is well suited to FPGA acquisition cards because its 14-bit parallel output can feed FPGA input registers directly and its 3 MSPS throughput supports repeated sampling of dynamic signals. The no-pipeline architecture allows the system to avoid correcting a stage-dependent conversion delay. Engineers should synchronize the acquisition clock, respect output setup and hold timing, and constrain the parallel bus for the required clock rate. The result is a deterministic path from the ADC sample command to captured digital data, which is valuable in vibration, waveform, and communications analysis.
מומלץ
Communications Receiver
The AD7484BST can serve as the high-speed sampling element in communications and receiver equipment that requires immediate conversion results and a parallel data path. Its track-and-hold capability above 40 MHz supports higher-bandwidth sampling than a typical low-speed SAR ADC, while 3 MSPS throughput is appropriate for many baseband measurement stages. In a receiver design, the RF or intermediate-frequency path should provide gain and filtering before the ADC, while the digital interface should be implemented with short, timing-constrained routes. Verify input swing, acquisition behavior, and reference accuracy against the application bandwidth.
מומלץ
Vibration and Transient Capture
The AD7484BST is appropriate for vibration, transient, and shock-analysis systems where capturing a waveform quickly is more important than minimizing conversion latency. Its 3 MSPS sampling rate and 14-bit resolution provide a practical balance between temporal resolution and dynamic range, while the track-and-hold supports signal content above 40 MHz. A typical channel uses an accelerometer or transducer, an analog anti-alias filter, and an input driver before conversion. The FPGA then captures the parallel word and applies filtering or spectral analysis using timestamped sample blocks.
מומלץ
Precision Instrumentation
The AD7484BST supports precision laboratory and industrial instruments that need more conversion speed than a slow measurement ADC but do not require the very high rates of a flash converter. The 14-bit SAR architecture offers a direct digital result, and the 3 MSPS rate allows multiple readings to be captured rapidly for filtering or statistical analysis. Front-end design should emphasize low-noise biasing, stable references, and isolation from digital return currents. The parallel interface can be read by an FPGA or connected through carefully timed digital logic, while the no-pipeline result simplifies sample timing.
מומלץ
Control-System Feedback
The AD7484BST can be used in fast control or feedback loops where an immediate conversion result is valuable. Because the SAR architecture has no pipeline delay, the sampled input can be represented without accounting for multiple pipeline stages. The 3 MSPS throughput permits roughly one conversion every 333 ns at its maximum rate, although practical loop timing must include acquisition, conversion, processing, and actuator delay. Analog input conditioning and digital isolation are essential for preventing switching activity from disturbing the measured control variable.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור AD7484BST — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | AD7484BSTZ |
|---|---|---|
| Package | 48-lead LQFP, 7 mm × 7 mm | 48-lead LQFP, 7 mm × 7 mm |
| Brand | Analog Devices | Analog Devices |
| Resolution | 14 bit | 14 bit |
| Conversion Throughput | 3 MSPS | 3 MSPS |
| Architecture | Successive approximation register (SAR) | Successive approximation register (SAR) |
| Input Channels | 1 channel | 1 channel |
| Data Interface | Parallel | Parallel |
| Pipeline Delay | 0 cycles | 0 cycles |
| Track-and-Hold Input Frequency | Greater than 40 MHz | Greater than 40 MHz |
| Temperature Grade | Industrial | Industrial |
מבדילים עיקריים
- Direct 3 MSPS conversion with no pipeline latency (לעומתAD7484BSTZ)
- High-bandwidth track-and-hold capability (לעומתAD7484BSTZ)
- Pin-compatible manufacturer ordering option (לעומתAD7484BSTZ)
הערות תכנון
Keep the AD7484BST analog input, reference, and decoupling connections short, with analog and digital return currents separated as far as the package and board area allow. Place input and reference capacitors close to their associated pins and provide a quiet ground path beneath the analog section when the board stackup permits. The 14-bit resolution and greater-than-40-MHz input capability make layout-sensitive reference and input errors more consequential than they would be in a slow precision-only measurement circuit.
Treat the 14-bit parallel output as a synchronous bus rather than a group of unrelated digital traces. Establish receiver setup and hold timing from the Analog Devices timing diagrams, constrain the relevant clock and data paths, and provide a continuous reference plane beneath the output routes. Account for output timing at the temperature and supply conditions used in the system. The absence of pipeline delay simplifies the digital protocol, but it does not relax the requirement for a clean clock and properly terminated interface.
Do not assume that the AD7484BST can capture any source connected to its input. The source impedance, input network, acquisition time, common-mode range, and reference accuracy must together allow a valid 14-bit conversion at the intended signal frequency. Use the manufacturer application information to select source impedance and decoupling, and avoid placing high-energy digital or switching-converter nodes near the analog input. Also verify the complete AD7484BST ordering code before releasing a PCB or production order.
מידע על תאימות
The AD7484BST is identified as an industrial-temperature-grade component, but exact ordering-code compliance declarations were not established. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status for the exact suffix in the current Analog Devices product documentation before production release.