Analog Devices

AD7484BST - 14-Bit 3 MSPS SAR ADC | Analog Devices

部品番号: AD7484BST ✓ 生産中
2.7 V Vdss 48-lead LQFP, 7 mm × 7 mm Package Greater than 40 MHz Speed
MOQ: 1 |

AD7484BST 概要

Analog Devices AD7484BST is a 14-bit, single-channel, high-speed successive-approximation register ADC capable of 3 MSPS conversion throughput in a 48-lead LQFP 7 mm × 7 mm package. It accepts analog input signals with frequencies above 40 MHz and provides a parallel interface with no pipeline delay.

A successive-approximation ADC, or SAR ADC, converts an analog voltage into a digital code through a sequence of internal comparisons. The SAR ADC family occupies the practical middle ground between high-resolution delta-sigma converters and very-high-speed flash converters. Unlike a pipelined ADC, the AD7484 does not introduce pipeline delay. This makes it suitable for systems requiring immediate acquisition results, coherent sampling, or deterministic control-loop timing.

The AD7484BST combines 14-bit resolution with a maximum throughput of 3 MSPS. Its low-noise, wide-bandwidth track-and-hold circuit supports input frequencies above 40 MHz, while the single-input architecture simplifies analog routing. The parallel data interface exposes the conversion result directly to digital logic and is appropriate for systems in which a processor, FPGA, or other parallel data-capture device reads the complete 14-bit result.

Operationally, the converter uses a proprietary algorithmic successive-approximation process rather than a pipeline architecture. Each conversion resolves the sampled input through successive internal decisions, and the result becomes available without a pipeline latency. Designers should still observe the required acquisition and conversion intervals from the manufacturer datasheet when establishing control-loop timing or maximum sampling frequency.

Typical applications include industrial process monitoring, instrumentation, communications receivers, vibration and signal analysis, data-acquisition systems, and control equipment. The 3 MSPS rate supports fast transient capture, while the 14-bit word provides useful resolution for general-purpose analog measurement. Its parallel output also makes it practical in FPGA-based acquisition platforms where converter data can be captured directly on a clock boundary.

The primary design consideration is signal conditioning and interface timing. Place input and reference decoupling close to the device, keep sensitive analog traces short, and use a stable reference arrangement that meets the converter’s accuracy requirements. Digital output timing, clocking, and input acquisition must be designed together because source impedance, sample-and-hold acquisition time, and settling behavior determine the usable input bandwidth.

This page combines the manufacturer’s technical overview, exact-package identification, verified commercial listing information, and practical interface guidance. It also documents drop-in replacement findings and distinguishes the AD7484BSTZ lead-free ordering option from a broader cross-brand replacement search.

ドロップイン代替品: AD7484BST — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

AD7484BSTZ

✅ ドロップイン
📦 48-lead LQFP, 7 mm × 7 mm
Same 14-bit, 3 MSPS parallel SAR converter and 48-pin LQFP footprint; ordering suffix differs in lead-free designation with 0% change to stated core performance.

📋 参考代替品(カタログ未掲載)

AD7484BST 最大定格&電気的特性

分解能 14 bit
Maximum Conversion Throughput 3 MSPS
Architecture Successive approximation register (SAR)
Number of Input Channels 1 channel
Input Frequency Capability Greater than 40 MHz
Data Interface Parallel
Pipeline Delay 0 cycles
Technology CMOS
パッケージ 48-lead LQFP, 7 mm × 7 mm
Package Code LFQFP
Terminal Count 48 terminals
Lead Style Gull wing
Temperature Grade Industrial
Input Supply Voltage 2.7 V
Track-and-Hold Architecture Low-noise, wide-bandwidth
Acquisition Conversion Method Proprietary algorithmic successive approximation

AD7484BST lfqfp ピン配置ガイド

AD7484BST (lfqfp パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

AD7484BST の lfqfp パッケージピン配置図

詳細なピン配置データはありません: AD7484BST.

詳細は データシート をご参照ください。

主な用途

AD7484BST の用途: 6 件s: Industrial Process Monitoring, FPGA-Based Data Acquisition, Communications Receiver, Vibration and Transient Capture, Precision Instrumentation, Control-System Feedback.

🏭

Industrial Process Monitoring

The AD7484BST fits fast process-monitoring systems that sample analog sensor or transducer signals while retaining 14-bit resolution. Its 3 MSPS throughput provides temporal headroom for capturing transients, and the wide-bandwidth track-and-hold can accept input frequencies exceeding 40 MHz when the front-end and acquisition network are designed accordingly. A typical arrangement places a buffered sensor signal into the ADC input, uses the manufacturer-recommended reference and decoupling network, and sends the parallel result to an FPGA or embedded controller. The absence of pipeline delay makes acquisition timing easier to relate to the sampled event.

🖥️

FPGA-Based Data Acquisition

The AD7484BST is well suited to FPGA acquisition cards because its 14-bit parallel output can feed FPGA input registers directly and its 3 MSPS throughput supports repeated sampling of dynamic signals. The no-pipeline architecture allows the system to avoid correcting a stage-dependent conversion delay. Engineers should synchronize the acquisition clock, respect output setup and hold timing, and constrain the parallel bus for the required clock rate. The result is a deterministic path from the ADC sample command to captured digital data, which is valuable in vibration, waveform, and communications analysis.

🌐

Communications Receiver

The AD7484BST can serve as the high-speed sampling element in communications and receiver equipment that requires immediate conversion results and a parallel data path. Its track-and-hold capability above 40 MHz supports higher-bandwidth sampling than a typical low-speed SAR ADC, while 3 MSPS throughput is appropriate for many baseband measurement stages. In a receiver design, the RF or intermediate-frequency path should provide gain and filtering before the ADC, while the digital interface should be implemented with short, timing-constrained routes. Verify input swing, acquisition behavior, and reference accuracy against the application bandwidth.

📡

Vibration and Transient Capture

The AD7484BST is appropriate for vibration, transient, and shock-analysis systems where capturing a waveform quickly is more important than minimizing conversion latency. Its 3 MSPS sampling rate and 14-bit resolution provide a practical balance between temporal resolution and dynamic range, while the track-and-hold supports signal content above 40 MHz. A typical channel uses an accelerometer or transducer, an analog anti-alias filter, and an input driver before conversion. The FPGA then captures the parallel word and applies filtering or spectral analysis using timestamped sample blocks.

🔧

Precision Instrumentation

The AD7484BST supports precision laboratory and industrial instruments that need more conversion speed than a slow measurement ADC but do not require the very high rates of a flash converter. The 14-bit SAR architecture offers a direct digital result, and the 3 MSPS rate allows multiple readings to be captured rapidly for filtering or statistical analysis. Front-end design should emphasize low-noise biasing, stable references, and isolation from digital return currents. The parallel interface can be read by an FPGA or connected through carefully timed digital logic, while the no-pipeline result simplifies sample timing.

⚙️

Control-System Feedback

The AD7484BST can be used in fast control or feedback loops where an immediate conversion result is valuable. Because the SAR architecture has no pipeline delay, the sampled input can be represented without accounting for multiple pipeline stages. The 3 MSPS throughput permits roughly one conversion every 333 ns at its maximum rate, although practical loop timing must include acquisition, conversion, processing, and actuator delay. Analog input conditioning and digital isolation are essential for preventing switching activity from disturbing the measured control variable.

What are the key specifications of AD7484BST that engineers should know?
The AD7484BST is a 14-bit, single-channel SAR ADC with throughput up to 3 MSPS, a parallel interface, no pipeline delay, and a 48-lead LQFP 7 mm × 7 mm package. According to the Analog Devices AD7484 data sheet, Rev. C, its low-noise, wide-bandwidth track-and-hold can handle input frequencies exceeding 40 MHz. The combination is intended for high-speed acquisition, instrumentation, process monitoring, and FPGA-based measurement systems.
What is the conversion speed of AD7484BST?
The AD7484BST supports a maximum throughput of 3 million conversions per second, or 3 MSPS. Analog Devices describes it as a 14-bit, high-speed, low-power successive-approximation ADC in the manufacturer data sheet, Rev. C. It uses a proprietary algorithmic SAR process and introduces no pipeline delay, allowing a newly completed conversion to be read without the latency found in pipelined converters.
Where can I download the AD7484BST datasheet PDF?
The official AD7484 documentation is available from the Analog Devices product page at analog.com/en/products/AD7484.html, where the manufacturer links the AD7484 data sheet, Rev. C. That document is the primary reference for the AD7484BST ordering information, electrical characteristics, pin assignments, timing diagrams, reference requirements, and application guidance. Use the manufacturer document rather than a third-party transcription when assigning PCB pins or designing the analog interface.
Where is the AD7484BST pinout located?
The AD7484BST pinout is located in the pin-configuration and pin-description tables of the Analog Devices AD7484 data sheet, Rev. C. The device is a 48-lead LQFP, so the package drawing and pin table cover all 48 terminals, including analog inputs, reference connections, supplies, clock signals, control signals, and parallel digital outputs. Do not infer the complete mapping from a distributor summary because several ADC pins have functional dependencies that must be checked in the datasheet.
What is the difference between a SAR ADC and a pipeline ADC?
A SAR ADC resolves an analog input through successive comparisons and typically updates its result directly, while a pipeline ADC uses multiple internal stages and therefore introduces pipeline latency. The AD7484BST is a 14-bit SAR ADC with throughput up to 3 MSPS and no pipeline delay, according to the Analog Devices AD7484 data sheet, Rev. C. This makes it attractive when the system needs immediate or deterministic sample-to-output timing.
What input frequencies can the AD7484BST track and hold?
The AD7484BST track-and-hold circuit can handle input frequencies in excess of 40 MHz, as specified in the Analog Devices AD7484 overview and data sheet, Rev. C. The usable bandwidth of a complete measurement path also depends on source impedance, the input network, acquisition time, reference stability, and PCB routing. High-frequency capability therefore does not remove the need for controlled impedance and careful analog layout.
Is AD7484BST suitable for FPGA-based data acquisition?
The AD7484BST is suitable for FPGA-based data acquisition because it combines a 14-bit resolution, throughput up to 3 MSPS, and a parallel data interface. The parallel outputs can connect to FPGA input registers when timing is designed for the converter’s clock and output-valid characteristics. Use the manufacturer timing diagrams to establish setup and hold requirements, and route the digital outputs with matched length and return-path discipline.
When should I choose AD7484BST over a slower SAR ADC?
Choose the AD7484BST when the acquisition system requires throughput up to 3 MSPS and needs input bandwidth above the conversion rate’s conventional low-frequency range. Its track-and-hold can handle frequencies exceeding 40 MHz, while its no-pipeline architecture provides immediate conversion results. A slower SAR ADC may be preferable only when lower speed, lower power, or a smaller package better matches the application and neither high-speed capture nor input bandwidth is required.
What is the best drop-in replacement for AD7484BST?
AD7484BSTZ is the directly identified drop-in option for AD7484BST. The cross-reference describes it as a completely replaceable 48-pin LQFP with consistent performance characteristics, functional behavior, terminals, and package. According to the Analog Devices AD7484 ordering documentation, both order codes belong to the same converter family; verify the exact suffix ordering code, temperature grade, and lead-free requirements against the current data sheet before production release.
Can AD7484BSTZ replace AD7484BST without PCB changes?
Yes, AD7484BSTZ can replace AD7484BST without PCB changes when the required temperature grade and ordering qualifications are satisfied. The cross-reference identifies matching 48-pin LQFP terminals, package, and functional characteristics, making it a drop-in option rather than a merely similar converter. Review the Analog Devices ordering guide and package marking to confirm that AD7484BSTZ is the exact approved configuration for the production build.
Is AD7484BST the same as AD7484BSTZ?
AD7484BST and AD7484BSTZ are closely related order codes for the same 14-bit, 3 MSPS AD7484 converter in a 48-pin LQFP package, and the documented cross-reference identifies AD7484BSTZ as a complete replacement. The suffix distinction should still be checked against the manufacturer ordering guide for lead-free status, package marking, and intended availability. Treat the ordering code, rather than a distributor family heading, as the controlling identifier.
What is the best Analog Devices equivalent for AD7484BST?
AD7484BSTZ is the best identified Analog Devices equivalent for AD7484BST because it retains the 14-bit SAR architecture, 3 MSPS throughput, parallel interface, and 48-lead LQFP footprint. The cross-reference explicitly describes it as a complete replacement with consistent terminals and package. No cross-brand drop-in alternative with verified pin compatibility was established, so changing manufacturers would require a separate engineering review rather than a blind substitution.
Where can I buy AD7484BST and check its current lead time?
Use the “Request a Quote” form on this page to request AD7484BST availability, current lead time, and a quotation. The form is the appropriate purchasing route for this catalog part and avoids stale commercial information. Before requesting an order, confirm that the quotation refers to the exact AD7484BST ordering code rather than the AD7484 family or the closely related AD7484BSTZ suffix.
Is AD7484BST in stock?
Current AD7484BST inventory should be confirmed through the “Request a Quote” form on this page because stock status changes across the supply chain. The manufacturer lists the AD7484 as a production device, while individual package suffixes can have different stocking and lifecycle conditions. Include the required quantity, date code, target packaging, and industrial temperature-grade requirements in the request.
What is the price of AD7484BST?
Use the “Request a Quote” form on this page for the current AD7484BST quotation and volume-break structure. Commercial pricing depends on quantity, date code, package suffix, inventory position, and delivery requirements, so a static unit figure should not be used for purchasing approval. Ensure the quotation identifies AD7484BST exactly and states whether the delivered part is new, traceable, and packaged for the intended assembly process.
Is AD7484BST compliant with RoHS and suitable for automotive use?
The AD7484BST is an industrial-temperature-grade converter, but RoHS, REACH, AEC-Q100, lead-free, and halogen-free classifications must be confirmed for the exact ordering code in the current Analog Devices documentation. Do not infer automotive qualification from the industrial temperature grade. For an automotive design, use an explicitly qualified ordering option and complete the manufacturer’s change-control and qualification review.

エンジニアリング参考データ: AD7484BST — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose AD7484BST when the design needs a 14-bit, single-channel SAR ADC with throughput up to 3 MSPS, parallel data transfer, and input bandwidth above 40 MHz. Its lack of pipeline delay is particularly useful in FPGA acquisition, instrumentation, vibration analysis, and feedback systems where sample timing must remain straightforward. AD7484BSTZ is the preferred drop-in alternative when the required ordering suffix includes the lead-free designation; it keeps the same 48-lead LQFP footprint and core performance. No cross-brand drop-in replacement has been established because equivalent resolution, throughput, timing, reference behavior, and 48-pin connectivity must all be confirmed before substitution. If the application needs only slow, low-power measurements, a smaller or slower ADC may be a better engineering choice even though it will not match the AD7484BST’s 3 MSPS throughput.

代替品との比較

パラメータ この製品 AD7484BSTZ
Package 48-lead LQFP, 7 mm × 7 mm 48-lead LQFP, 7 mm × 7 mm
Brand Analog Devices Analog Devices
Resolution 14 bit 14 bit
Conversion Throughput 3 MSPS 3 MSPS
Architecture Successive approximation register (SAR) Successive approximation register (SAR)
Input Channels 1 channel 1 channel
Data Interface Parallel Parallel
Pipeline Delay 0 cycles 0 cycles
Track-and-Hold Input Frequency Greater than 40 MHz Greater than 40 MHz
Temperature Grade Industrial Industrial

主な差別化要因

  • Direct 3 MSPS conversion with no pipeline latency (vs AD7484BSTZ)
  • High-bandwidth track-and-hold capability (vs AD7484BSTZ)
  • Pin-compatible manufacturer ordering option (vs AD7484BSTZ)

設計ノート

Keep the AD7484BST analog input, reference, and decoupling connections short, with analog and digital return currents separated as far as the package and board area allow. Place input and reference capacitors close to their associated pins and provide a quiet ground path beneath the analog section when the board stackup permits. The 14-bit resolution and greater-than-40-MHz input capability make layout-sensitive reference and input errors more consequential than they would be in a slow precision-only measurement circuit.

Treat the 14-bit parallel output as a synchronous bus rather than a group of unrelated digital traces. Establish receiver setup and hold timing from the Analog Devices timing diagrams, constrain the relevant clock and data paths, and provide a continuous reference plane beneath the output routes. Account for output timing at the temperature and supply conditions used in the system. The absence of pipeline delay simplifies the digital protocol, but it does not relax the requirement for a clean clock and properly terminated interface.

Do not assume that the AD7484BST can capture any source connected to its input. The source impedance, input network, acquisition time, common-mode range, and reference accuracy must together allow a valid 14-bit conversion at the intended signal frequency. Use the manufacturer application information to select source impedance and decoupling, and avoid placing high-energy digital or switching-converter nodes near the analog input. Also verify the complete AD7484BST ordering code before releasing a PCB or production order.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The AD7484BST is identified as an industrial-temperature-grade component, but exact ordering-code compliance declarations were not established. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status for the exact suffix in the current Analog Devices product documentation before production release.

データ検証日: 2026-11-18 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

AD7484BST datasheet AD7484BST pinout AD7484BST datasheet pdf AD7484BST specifications AD7484BST 3 MSPS AD7484BST 14 bit ADC AD7484BST LQFP-48 AD7484BST equivalent AD7484BST replacement AD7484BST vs AD7484BSTZ AD7484BST application circuit Analog Devices AD7484BST AD7484BST price AD7484BST stock where to buy AD7484BST

関連部品&用語

Analog Devices AD7484BST AD7484BSTZ AD7484 SAR ADC successive approximation register analog-to-digital converter ADC data acquisition track-and-hold 14-bit resolution 3 MSPS throughput parallel data interface no pipeline delay 48-lead LQFP LQFP package family surface-mount package FPGA industrial instrumentation process monitoring communications receiver vibration analysis CMOS Analog Input Digital Data Bus
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示