ADF4355BCPZ-RL7 - 6.8 GHz Fractional-N PLL Synthesizer | Analog Devices
MPN: ADF4355BCPZ-RL7 ✓ פעילADF4355BCPZ-RL7 סקירה
A fractional-N frequency synthesizer generates an accurate output frequency by combining a phase-locked loop with an integrated VCO and programmable divider. Its frequency resolution is set by a high-order fractional modulus, while integer-N operation provides a simpler configuration for applications that do not require fractional feedback. The ADF4355 belongs to the PLL synthesizer family within clock and timing integrated circuits, where it serves as a programmable RF clock source for communications, test equipment, and signal-generation systems.
The integrated VCO eliminates the need for an external VCO, reducing board area while supporting RF outputs up to 6.8 GHz. A 38-bit modulus enables fine channel spacing, and the output divider can be programmed from divide-by-1 through divide-by-64. The 3-wire control interface operates with 1.8 V-compatible logic, allowing direct connection to low-voltage control hardware. Analog and digital power are supplied at 3.3 V, while the charge-pump and VCO supply arrangement uses 5.0 V typical operation.
A practical implementation includes an external reference source, reference divider, loop filter, and output-matching network. The external loop filter determines loop bandwidth, phase noise, spur performance, and lock time, so component selection and PCB placement are as important as the synthesizer settings. Register programming controls the channel frequency, fractional value, output division, reference path, and power state. Hardware and software lock-detect functions support reliable frequency acquisition in production systems.
Typical uses include microwave and wideband RF signal generation, wireless communications test equipment, local oscillator generation, radar test systems, and instrumentation requiring programmable frequencies between 54 MHz and 6.8 GHz. The device is particularly useful when one synthesizer must cover multiple output dividers and closely spaced fractional-N channels without using multiple separate VCO assemblies.
For a reliable layout, place the loop-filter components and RF matching network close to their associated pins, maintain short return paths around the exposed pad, and follow the Analog Devices recommended decoupling arrangement. Confirm the external reference level and loop-filter values against the operating channel, divider ratio, and required phase-noise performance before production release.
This product page consolidates the RF frequency range, supply requirements, package information, application guidance, comparison considerations, and drop-in candidate assessment into one engineering-focused reference for ADF4355BCPZ-RL7 designs.
חלופות תחליף ישיר עבור ADF4355BCPZ-RL7 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ADF4355BCPZ-RL7 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Analog and Digital Supply Voltage, Charge Pump and VCO Supply Voltage, Device Type, Maximum RF Output Frequency.
ADF4355-3BCPZ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ADF4356BCPZ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ADF4355BCPZ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ADF4355BCPZ-RL7 מפרטים
| RF Output Frequency Range | 54 MHz to 6800 MHz |
| Synthesizer Architecture | Fractional-N or integer-N |
| Fractional Modulus | 38 bit |
| Integrated VCO | Yes |
| Programmable Output Divider | Divide by 1, 2, 4, 8, 16, 32, or 64 |
| Analog and Digital Supply Voltage | 3.3 V |
| Charge Pump and VCO Supply Voltage | 5.0 V typical |
| Logic Compatibility | 1.8 V |
| Control Interface | 3-wire serial interface |
| Lock Detect | Analog and digital |
| Reference Input Frequency | 10 MHz to 600 MHz |
| טווח טמפרטורת פעולה | -40°C to +85°C |
| מארז | 32-lead WFQFN with exposed pad |
| Package Type | LFCSP-32 with exposed pad |
| סוג הרכבה | Surface mount |
| Shipping Format | 7-inch tape-and-reel |
מדריך תצורת פינים של ADF4355BCPZ-RL7 lfcsp-32 with exposed pad
תצורת פינים עבור ADF4355BCPZ-RL7 (מארזת lfcsp-32 with exposed pad). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור ADF4355BCPZ-RL7.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
ADF4355BCPZ-RL7 מתאים עבור 6 יישוםs: Wideband RF Signal Generators, Communications Test Equipment, Microwave Instrumentation, Radar and Microwave Test Systems, Wireless Baseband and RF Evaluation, Industrial RF Measurement Systems.
Wideband RF Signal Generators
The ADF4355BCPZ-RL7 fits wideband RF signal generators because its integrated VCO covers 54 MHz to 6800 MHz and its output divider supports division from 1 through 64. A designer can use fractional-N operation with the 38-bit modulus for fine frequency spacing while retaining integer-N operation for simpler configurations. The 3-wire control interface also simplifies frequency updates in automated test systems. External loop-filter and RF matching networks remain necessary to establish the intended phase-noise, spur, and output-amplitude performance on the completed board.
מומלץ
Communications Test Equipment
ADF4355BCPZ-RL7 is suitable for programmable communications test equipment requiring a local oscillator or RF reference with broad frequency coverage. Its 54 MHz to 6800 MHz output range supports multiple radio-frequency test bands, while the 38-bit fractional modulus provides fine channel selection. The programmable divide-by-1 through divide-by-64 output stages allow one RF chain to serve several measurement ranges. For production instruments, use the analog and digital lock-detect functions to prevent measurements from being taken before the PLL reaches its commanded frequency.
מומלץ
Microwave Instrumentation
The ADF4355BCPZ-RL7 can serve as the integrated RF source in microwave instrumentation where a compact, programmable synthesizer is required. Covering outputs up to 6800 MHz, it eliminates the need for a discrete VCO and its associated matching components. The 32-lead exposed-pad package supports compact RF layouts, although its exposed thermal pad still requires adequate copper and via distribution. Engineers should tune the external loop filter against the required phase-noise floor and settling time, then validate output level across the selected divider ratios.
מומלץ
Radar and Microwave Test Systems
ADF4355BCPZ-RL7 is well matched to radar and microwave test systems that need a programmable RF excitation or local-oscillator source over a wide frequency span. The fractional-N architecture permits narrow synthesized steps, and the selectable output dividers support several RF test ranges from one device. Its 1.8 V-compatible control logic can be driven by low-voltage test-control hardware. System-level performance depends on the chosen reference source, external loop filter, RF output matching, and thermal layout, which must be characterized under the intended operating channel and load conditions.
מומלץ
Wireless Baseband and RF Evaluation
ADF4355BCPZ-RL7 supports wireless RF evaluation platforms that need programmable oscillator coverage without a separate VCO assembly. Its output reaches 6800 MHz, while selectable division and fractional-N settings allow designers to create multiple test tones or local-oscillator conditions. The 3-wire interface simplifies integration with FPGA-based or microcontroller-based control systems. Because the synthesizer still requires an external reference and loop filter, the evaluation board should provide clean supplies, short RF paths, and controlled impedance routing to obtain repeatable phase-noise and output-power measurements.
מומלץ
Industrial RF Measurement Systems
ADF4355BCPZ-RL7 fits industrial RF measurement systems that require repeatable programmable frequency generation across a wide operating band. Its integrated VCO reduces external RF-component count, and the -40°C to +85°C specification supports demanding equipment environments. The 38-bit fractional modulus allows precise channel placement, while analog and digital lock indication can coordinate measurement timing. Design the loop filter for the desired settling time and phase-noise balance, and confirm the RF output performance over temperature before deploying the system in factory or field test equipment.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ADF4355BCPZ-RL7 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ADF4355-3BCPZ | ADF4356BCPZ | ADF4355BCPZ |
|---|---|---|---|---|
| Package | 32-lead LFCSP with exposed pad | 32-lead LFCSP with exposed pad | 32-lead LFCSP with exposed pad | 32-lead LFCSP with exposed pad |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Fractional-N and integer-N PLL frequency synthesizer with integrated VCO | Fractional-N PLL frequency synthesizer with integrated VCO | Fractional-N PLL frequency synthesizer with integrated VCO | Fractional-N and integer-N PLL frequency synthesizer with integrated VCO |
מבדילים עיקריים
- Broad integrated-VCO coverage (לעומתADF4355BCPZ)
- Multi-supply compatibility with the established ADF4355 architecture (לעומתADF4355-3BCPZ)
- 7-inch reel ordering configuration (לעומתADF4355BCPZ)
- Programmable output flexibility (לעומתADF4356BCPZ)
הערות תכנון
Implement the loop filter and RF matching networks close to their associated pins, using short ground returns and a continuous ground reference beneath the exposed pad. The 32-lead exposed-pad package requires thermal vias or equivalent copper paths to distribute heat while maintaining the manufacturer's recommended component spacing. Treat the RF output path as a controlled-impedance layout and keep the reference, charge-pump, and VCO return-current paths short.
Decouple the 3.3 V analog and digital domains and the 5.0 V typical charge-pump and VCO domains according to the reference schematic. Place bypass capacitors directly beside their relevant supply pins to suppress high-frequency coupling between the VCO, charge pump, and digital control sections. Do not assume the supply pins can share a single unrestricted plane connection; verify each rail's return path and voltage limits on the finished board.
Choose loop-filter values for the required reference frequency, channel spacing, lock time, and phase-noise target rather than copying a generic filter without recalculation. Use the analog and digital lock-detect functions to gate downstream measurements or RF-enable actions. Confirm settling at the lowest expected load and across temperature because reference phase noise, loop bandwidth, and PCB parasitics can alter practical performance.
מידע על תאימות
The device is not identified as an automotive-qualified part in the available manufacturer information. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or shipment declaration.