Analog Devices

ADM241LJRS - 120kbps RS-232 Transceiver | Analog Devices

MPN: ADM241LJRS ✓ פעיל
5 V Vdss ≤1 µA Id 28-pin SSOP Package
כמות הזמנה מינימלית: 1 |

ADM241LJRS סקירה

The Analog Devices ADM241LJRS is a 4/5 RS-232 transceiver operating from a single 5 V supply, supporting data rates up to 120 kbps in a 28-pin SSOP package. It integrates four drivers and five receivers, on-board DC-to-DC converters, and charge-pump circuitry that produces approximately ±9 V output swing without requiring external ±12 V power rails. The interface meets EIA-232-E and V.28 requirements.

An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar differential signaling used by RS-232 equipment. It belongs to the interface IC hierarchy, combining line drivers, line receivers, voltage conversion, and port protection into a complete communications interface. This integration is especially useful when the equipment only has a 5 V supply but must communicate with legacy RS-232 ports requiring positive and negative signal voltages.

The ADM241LJRS supports a maximum 120 kbps data rate while consuming small 1 µF charge-pump capacitors. Its integrated converters eliminate separate negative-voltage generation circuitry, reducing board area and external component count. A low-power shutdown mode reduces supply current to 1 µA or less, and the receiver inputs tolerate voltages up to ±30 V. The 28-pin SSOP package provides enough channel capacity for four transmit and five receive functions.

The ADM241LJRS is intended for industrial control, instrumentation, data acquisition, point-of-sale equipment, and embedded serial-port designs. Its four-driver and five-receiver arrangement suits equipment that sends commands and status information while receiving data from several peripherals. The single 5 V rail also simplifies compatibility with modern digital systems that no longer provide the ±12 V rails traditionally associated with RS-232.

PCB design should prioritize short traces between the device and charge-pump capacitors because high-current switching paths can create radiated noise and ground disturbance. Place the interface connector, protection network, transceiver, and connector-side ground connection in a controlled signal-flow arrangement. Review the manufacturer datasheet before finalizing capacitor selection, connector protection, and logic-family compatibility.

This page combines the manufacturer's published interface capabilities with application guidance, practical design considerations, verified source links, and a strict assessment of drop-in replacement options. Engineers can use the comparison and selection information to determine whether the ADM241LJRS matches the required channel count, package, data rate, and RS-232 system architecture.

חלופות תחליף ישיר עבור ADM241LJRS — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

אין חלופות תואמות Drop-in עבור מוצר זה.

בקשת חלופות

ADM241LJRS מפרטים

Product Type 4/5 RS-232 transceiver
מתח אספקה 5 V
Maximum Data Rate 120 kbps
Driver Count 4 drivers
Receiver Count 5 receivers
RS-232 Output Swing ±9 V from a 5 V supply
Charge-Pump Capacitor Value 1 µF
Shutdown Supply Current ≤1 µA
Receiver Input Voltage Tolerance ±30 V
RS-232 Compliance EIA-232-E and V.28
Integrated Voltage Conversion On-board DC-to-DC converters
מארז 28-pin SSOP
סוג הרכבה Surface mount
Latch-Up Protection Latch-up free

מדריך תצורת פינים של ADM241LJRS 28-pin ssop

תצורת פינים עבור ADM241LJRS (מארזת 28-pin ssop). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 28-pin ssop עבור ADM241LJRS

אין נתוני פריסת פינים מפורטים עבור ADM241LJRS.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

ADM241LJRS מתאים עבור 6 יישוםs: Industrial Instrument Control, Point-of-Sale Terminal Interface, Data Acquisition System, Embedded Serial Port Expansion, Network Equipment Management, Test and Measurement Equipment.

🏭

Industrial Instrument Control

The ADM241LJRS fits legacy RS-232 instrument interfaces because it combines four drivers and five receivers with a maximum 120 kbps data rate. It operates from one 5 V rail while its on-board DC-to-DC converters produce approximately ±9 V output swing, reducing the need for a separate negative supply in controller boards. Four command or control channels can be supported alongside five incoming status paths. Confirm logic-family levels, connector protection, and the manufacturer's operating-temperature limits before deploying the interface in production equipment.

🖥️

Point-of-Sale Terminal Interface

Point-of-sale equipment can use the ADM241LJRS to bridge modern control logic with several RS-232 peripherals while keeping the power architecture simple. The single 5 V operation and integrated voltage converters remove the conventional external negative-voltage rail, while 1 µF charge-pump capacitors simplify the surrounding component set. The four transmitters can support independent peripheral buses or multidrop arrangements when the system designer follows RS-232 topology and signal-return requirements. Use the receiver channels for peripheral status and confirmation traffic.

🔧

Data Acquisition System

The ADM241LJRS is appropriate for data-acquisition equipment that must collect status or command information from multiple RS-232 instruments. Its five receivers provide dedicated input paths, while four drivers support configuration commands, triggers, or acknowledgements. A 120 kbps maximum rate is suitable for moderate-speed control and telemetry rather than continuous high-bandwidth sensor streaming. The receiver inputs can tolerate up to ±30 V, adding useful margin when connected through suitable protection networks to external equipment.

🌐

Network Equipment Management

The ADM241LJRS can support management and console connections in network or communications equipment that retains RS-232 service interfaces. The four transmit channels and five receive channels allow multiple management functions to share one interface IC, while the 120 kbps rate is suitable for command consoles and supervisory protocols. The integrated 5 V-to-RS-232 voltage conversion simplifies systems without ±12 V rails. Protection should be selected for the actual connector exposure and cable length rather than relying solely on the IC's internal receiver tolerance.

🔧

Test and Measurement Equipment

The ADM241LJRS is suitable for legacy RS-232 control ports on test and measurement equipment because it combines multiple channels, integrated voltage conversion, and a 120 kbps operating limit. Instrument control traffic, calibration commands, and diagnostic responses can share the transceiver while keeping the system powered from 5 V logic rails. The approximately ±9 V generated swing supports compliant RS-232 signaling, but cable length, ground reference, and connector protection must be handled at the system level. Review the datasheet for timing and shutdown details before fixing the firmware strategy.

What are the key specifications of ADM241LJRS that engineers should know?
The ADM241LJRS is a 5 V, 4-driver and 5-receiver RS-232 transceiver rated for data rates up to 120 kbps in a 28-pin SSOP package. According to the Analog Devices manufacturer datasheet, it meets EIA-232-E and V.28 requirements, generates approximately ±9 V from on-board DC-to-DC converters, uses 1 µF charge-pump capacitors, supports shutdown current of 1 µA or less, and tolerates receiver inputs up to ±30 V.
What is the operating voltage of ADM241LJRS?
The ADM241LJRS operates from a single 5 V supply. According to the Analog Devices manufacturer datasheet, its on-board DC-to-DC converters generate the positive and negative voltages required for approximately ±9 V RS-232 output swing. This allows the interface to operate without a separate ±12 V supply, although external logic must still remain compatible with the transceiver's interface levels.
What is the maximum data rate of ADM241LJRS?
The ADM241LJRS supports data rates up to 120 kbps. The Analog Devices manufacturer datasheet identifies the device as a 4/5 RS-232 transceiver designed to meet EIA-232-E and V.28 specifications. This rate is suitable for instrument control, point-of-sale systems, data acquisition, and industrial serial links, but it should not be confused with RS-485 or RS-422 high-speed differential interfaces.
Does ADM241LJRS require external negative voltage?
No. The ADM241LJRS uses on-board DC-to-DC converters to produce approximately ±9 V output swing from its single 5 V supply. According to the Analog Devices manufacturer datasheet, the charge-pump system requires small 1 µF capacitors, eliminating the external negative-voltage rail and most of the discrete components associated with conventional RS-232 interface designs.
Where can I download the ADM241LJRS datasheet PDF?
The official Analog Devices ADM241L product page is the appropriate starting point for the ADM241LJRS datasheet and technical documentation. The linked manufacturer page provides the product overview and downloadable documentation, including the device family information covering the 5 V supply, 120 kbps data rate, on-board converters, ±9 V swing, and EIA-232-E and V.28 compliance.
Where can I find the ADM241LJRS pinout?
Use the pin-description table and package drawing in the Analog Devices ADM241L manufacturer datasheet to assign the ADM241LJRS connections. The component is supplied in a 28-pin SSOP package and includes driver, receiver, supply, ground, enable, shutdown, and charge-pump connections. Because the exact terminal names are not reproduced on this page, use the datasheet as the authoritative source for PCB routing.
Is ADM241LJRS suitable for industrial equipment?
The ADM241LJRS is suitable for industrial serial-interface designs when the application requires RS-232 signaling from a 5 V supply. Its 120 kbps maximum data rate, ±30 V receiver input tolerance, EIA-232-E compliance, and V.28 compliance support legacy equipment interfaces. For harsh installations, confirm the device's specified operating temperature range and implement appropriate connector-level surge protection.
What is the difference between ADM241LJRS and a conventional RS-232 transceiver?
The ADM241LJRS combines four drivers, five receivers, and on-board DC-to-DC converters in one 28-pin SSOP package. According to the Analog Devices manufacturer datasheet, its integrated converters deliver approximately ±9 V from a single 5 V rail, while a conventional implementation may require external charge pumps or a separate negative supply. Its 1 µF charge-pump capacitors also help reduce external component count.
Where to buy ADM241LJRS online?
Use the Request a Quote form on this page to request ADM241LJRS availability, order quantities, and a current quotation. The form is the appropriate commercial channel for this product without relying on potentially stale catalog pricing. For technical confirmation, include the required quantity, delivery destination, and whether you need tape-and-reel production quantities.
What is the price of ADM241LJRS?
The current commercial price for ADM241LJRS is obtained through the Request a Quote form on this page. The form allows quantity, packaging, and delivery requirements to be included in the quotation request. Because market availability and pricing can change, request a current quotation rather than relying on a historical catalog figure for production planning.
What is the lead time for ADM241LJRS?
Current lead time and minimum order quantity for ADM241LJRS should be confirmed through the Request a Quote form on this page. Include the required delivery date and production quantity so the commercial response can reflect realistic scheduling. Engineers should not release a schedule based only on general inventory messaging because component availability may change by package, quantity, and date.
Is ADM241LJRS in stock?
ADM241LJRS stock status should be checked through the Request a Quote form on this page, where the requested quantity and delivery requirements can be evaluated together. A distributor page indicating that orders may ship is not a guaranteed allocation for every quantity. For production planning, request current availability for the exact MPN, package, and required shipment date.
When should I choose ADM241LJRS instead of a discrete RS-232 interface?
Choose ADM241LJRS when a design requires a 5 V RS-232 interface with several channels and minimal external circuitry. Four drivers, five receivers, integrated voltage conversion, 1 µF charge-pump capacitors, and a 120 kbps data rate make it suitable for multi-channel industrial and instrumentation equipment. A discrete solution may be preferable only when its additional cost, size, or customization provides a specific circuit-level benefit.
Can MAX3221IPWR replace ADM241LJRS in the same PCB?
The MAX3221IPWR cannot be treated as a confirmed drop-in replacement for the ADM241LJRS because it uses a smaller 16-pin package and does not preserve the ADM241LJRS four-driver and five-receiver pin arrangement. Although both devices implement RS-232 interfaces, changing between them requires footprint, pinout, channel-count, and supply verification. Use the MAX3221IPWR for a new compatible design rather than assuming a board-level substitution.
What is the best drop-in replacement for ADM241LJRS?
No pin-compatible drop-in replacement for the ADM241LJRS is established by the available manufacturer and cross-reference information. Several comparable RS-232 interface ICs exist, but matching the function is not enough: a valid replacement must also retain the 28-pin SSOP footprint, pin assignments, 5 V operation, driver and receiver counts, shutdown behavior, and 120 kbps-class performance. Request engineering review before approving any substitution.

נתוני עזר הנדסיים עבור ADM241LJRS — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the ADM241LJRS when a design needs a high channel-count RS-232 interface powered from a single 5 V rail. Its four drivers, five receivers, 120 kbps maximum data rate, and integrated DC-to-DC converters are useful in industrial controllers, instrumentation, and legacy equipment interfaces. A smaller MAX3221-family device may be more appropriate when only one transmit and one receive path is required and the PCB can be redesigned around its 16-pin package. Do not use the MAX3221IPWR as a pin-to-pin substitute for an existing ADM241LJRS board. Before selecting the ADM241LJRS, verify that five receiver inputs and four outputs justify the larger package, confirm 5 V logic compatibility, and reserve space for charge-pump capacitors and connector protection.

השוואה עם חלופות

פרמטר מוצר זה
Product Type 4/5 RS-232 transceiver
Brand Analog Devices
Package 28-pin SSOP
Supply Voltage 5 V
Maximum Data Rate 120 kbps
Driver Count 4 drivers
Receiver Count 5 receivers
RS-232 Output Swing ±9 V from a 5 V supply
Charge-Pump Capacitor Value 1 µF
Shutdown Supply Current ≤1 µA
Receiver Input Voltage Tolerance ±30 V
Compliance EIA-232-E and V.28

מבדילים עיקריים

  • Four drivers and five receivers in one interface IC (לעומתNo confirmed pin-compatible drop-in alternative)
  • Single 5 V supply with integrated negative-voltage generation (לעומתNo confirmed pin-compatible drop-in alternative)
  • High channel density in a 28-pin SSOP (לעומתNo confirmed pin-compatible drop-in alternative)

הערות תכנון

Place the 1 µF charge-pump capacitors close to their specified terminals and keep the associated switching-current paths compact. These capacitors and the DC-to-DC converter carry high-frequency charge-pump current; long traces can increase radiated emissions and cause ground bounce. Route the converter and driver return currents directly to the device ground pins instead of through long paths shared with connector or logic return currents.

Arrange the PCB signal flow from logic circuitry through the ADM241LJRS and protection network to the RS-232 connector. Keep the protected connector side physically separate from sensitive logic, and provide a direct chassis or signal-ground connection according to the equipment grounding architecture. The receiver's ±30 V input tolerance is not a substitute for external surge and ESD protection, especially for user-accessible connectors.

Do not treat every RS-232 transceiver as a board-level substitute. A valid drop-in replacement must match the 28-pin SSOP footprint, exact pin assignments, 5 V supply arrangement, four-driver and five-receiver channel count, shutdown behavior, and required data rate. Also verify the logic-side voltage levels, because a compatible RS-232 line interface does not guarantee compatibility with 3.3 V controller I/O.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

EIA-232-E and V.28 interface compliance is documented. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current manufacturer documentation.

הנתונים אומתו בתאריך: 2026-11-14 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

ADM241LJRS datasheet ADM241LJRS pinout ADM241LJRS datasheet pdf ADM241LJRS specifications ADM241LJRS equivalent ADM241LJRS replacement ADM241LJRS cross reference ADM241LJRS price ADM241LJRS stock Analog Devices ADM241LJRS ADM241LJRS 28 SSOP pinout ADM241LJRS RS-232 application circuit

רכיבים ומונחים קשורים

Analog Devices ADM241LJRS ADM241L RS-232 transceiver RS-232 EIA-232-E V.28 interface IC line driver line receiver DC-to-DC converter charge-pump capacitor 120 kbps 5 V power supply ±9 V output swing ±30 V receiver input 28-pin SSOP surface mount industrial control data acquisition instrument control point-of-sale equipment RS-232 shutdown
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר