ADM241LJRS - 120kbps RS-232 Transceiver | Analog Devices
MPN: ADM241LJRS ✓ 啟用中ADM241LJRS 概覽
An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar differential signaling used by RS-232 equipment. It belongs to the interface IC hierarchy, combining line drivers, line receivers, voltage conversion, and port protection into a complete communications interface. This integration is especially useful when the equipment only has a 5 V supply but must communicate with legacy RS-232 ports requiring positive and negative signal voltages.
The ADM241LJRS supports a maximum 120 kbps data rate while consuming small 1 µF charge-pump capacitors. Its integrated converters eliminate separate negative-voltage generation circuitry, reducing board area and external component count. A low-power shutdown mode reduces supply current to 1 µA or less, and the receiver inputs tolerate voltages up to ±30 V. The 28-pin SSOP package provides enough channel capacity for four transmit and five receive functions.
The ADM241LJRS is intended for industrial control, instrumentation, data acquisition, point-of-sale equipment, and embedded serial-port designs. Its four-driver and five-receiver arrangement suits equipment that sends commands and status information while receiving data from several peripherals. The single 5 V rail also simplifies compatibility with modern digital systems that no longer provide the ±12 V rails traditionally associated with RS-232.
PCB design should prioritize short traces between the device and charge-pump capacitors because high-current switching paths can create radiated noise and ground disturbance. Place the interface connector, protection network, transceiver, and connector-side ground connection in a controlled signal-flow arrangement. Review the manufacturer datasheet before finalizing capacitor selection, connector protection, and logic-family compatibility.
This page combines the manufacturer's published interface capabilities with application guidance, practical design considerations, verified source links, and a strict assessment of drop-in replacement options. Engineers can use the comparison and selection information to determine whether the ADM241LJRS matches the required channel count, package, data rate, and RS-232 system architecture.
直接替換替代品,適用於 ADM241LJRS — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品ADM241LJRS 規格
| Product Type | 4/5 RS-232 transceiver |
| 供應電壓 | 5 V |
| Maximum Data Rate | 120 kbps |
| Driver Count | 4 drivers |
| Receiver Count | 5 receivers |
| RS-232 Output Swing | ±9 V from a 5 V supply |
| Charge-Pump Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Tolerance | ±30 V |
| RS-232 Compliance | EIA-232-E and V.28 |
| Integrated Voltage Conversion | On-board DC-to-DC converters |
| 封裝 | 28-pin SSOP |
| 安裝類型 | Surface mount |
| Latch-Up Protection | Latch-up free |
ADM241LJRS 28-pin ssop 腳位配置指南
ADM241LJRS(28-pin ssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADM241LJRS.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADM241LJRS 適用於 6 應用s: Industrial Instrument Control, Point-of-Sale Terminal Interface, Data Acquisition System, Embedded Serial Port Expansion, Network Equipment Management, Test and Measurement Equipment.
Industrial Instrument Control
The ADM241LJRS fits legacy RS-232 instrument interfaces because it combines four drivers and five receivers with a maximum 120 kbps data rate. It operates from one 5 V rail while its on-board DC-to-DC converters produce approximately ±9 V output swing, reducing the need for a separate negative supply in controller boards. Four command or control channels can be supported alongside five incoming status paths. Confirm logic-family levels, connector protection, and the manufacturer's operating-temperature limits before deploying the interface in production equipment.
推薦
Point-of-Sale Terminal Interface
Point-of-sale equipment can use the ADM241LJRS to bridge modern control logic with several RS-232 peripherals while keeping the power architecture simple. The single 5 V operation and integrated voltage converters remove the conventional external negative-voltage rail, while 1 µF charge-pump capacitors simplify the surrounding component set. The four transmitters can support independent peripheral buses or multidrop arrangements when the system designer follows RS-232 topology and signal-return requirements. Use the receiver channels for peripheral status and confirmation traffic.
推薦
Data Acquisition System
The ADM241LJRS is appropriate for data-acquisition equipment that must collect status or command information from multiple RS-232 instruments. Its five receivers provide dedicated input paths, while four drivers support configuration commands, triggers, or acknowledgements. A 120 kbps maximum rate is suitable for moderate-speed control and telemetry rather than continuous high-bandwidth sensor streaming. The receiver inputs can tolerate up to ±30 V, adding useful margin when connected through suitable protection networks to external equipment.
推薦
Embedded Serial Port Expansion
推薦
Network Equipment Management
The ADM241LJRS can support management and console connections in network or communications equipment that retains RS-232 service interfaces. The four transmit channels and five receive channels allow multiple management functions to share one interface IC, while the 120 kbps rate is suitable for command consoles and supervisory protocols. The integrated 5 V-to-RS-232 voltage conversion simplifies systems without ±12 V rails. Protection should be selected for the actual connector exposure and cable length rather than relying solely on the IC's internal receiver tolerance.
推薦
Test and Measurement Equipment
The ADM241LJRS is suitable for legacy RS-232 control ports on test and measurement equipment because it combines multiple channels, integrated voltage conversion, and a 120 kbps operating limit. Instrument control traffic, calibration commands, and diagnostic responses can share the transceiver while keeping the system powered from 5 V logic rails. The approximately ±9 V generated swing supports compliant RS-232 signaling, but cable length, ground reference, and connector protection must be handled at the system level. Review the datasheet for timing and shutdown details before fixing the firmware strategy.
推薦
推薦產品摘要
工程參考資料,適用於 ADM241LJRS — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Product Type | 4/5 RS-232 transceiver |
| Brand | Analog Devices |
| Package | 28-pin SSOP |
| Supply Voltage | 5 V |
| Maximum Data Rate | 120 kbps |
| Driver Count | 4 drivers |
| Receiver Count | 5 receivers |
| RS-232 Output Swing | ±9 V from a 5 V supply |
| Charge-Pump Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Tolerance | ±30 V |
| Compliance | EIA-232-E and V.28 |
主要差異化特點
- Four drivers and five receivers in one interface IC (對比No confirmed pin-compatible drop-in alternative)
- Single 5 V supply with integrated negative-voltage generation (對比No confirmed pin-compatible drop-in alternative)
- High channel density in a 28-pin SSOP (對比No confirmed pin-compatible drop-in alternative)
設計說明
Place the 1 µF charge-pump capacitors close to their specified terminals and keep the associated switching-current paths compact. These capacitors and the DC-to-DC converter carry high-frequency charge-pump current; long traces can increase radiated emissions and cause ground bounce. Route the converter and driver return currents directly to the device ground pins instead of through long paths shared with connector or logic return currents.
Arrange the PCB signal flow from logic circuitry through the ADM241LJRS and protection network to the RS-232 connector. Keep the protected connector side physically separate from sensitive logic, and provide a direct chassis or signal-ground connection according to the equipment grounding architecture. The receiver's ±30 V input tolerance is not a substitute for external surge and ESD protection, especially for user-accessible connectors.
Do not treat every RS-232 transceiver as a board-level substitute. A valid drop-in replacement must match the 28-pin SSOP footprint, exact pin assignments, 5 V supply arrangement, four-driver and five-receiver channel count, shutdown behavior, and required data rate. Also verify the logic-side voltage levels, because a compatible RS-232 line interface does not guarantee compatibility with 3.3 V controller I/O.
合規資訊
EIA-232-E and V.28 interface compliance is documented. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current manufacturer documentation.