ADM3063EARZ - 500kbps Full-Duplex RS-485 | Analog Devices
MPN: ADM3063EARZ ✓ פעילADM3063EARZ סקירה
An RS-485 transceiver combines a differential line driver and differential receiver into one physical-layer interface. The driver converts a logic-level signal into a balanced differential bus output, while the receiver converts differential bus voltage into a logic-level signal. Full-duplex operation uses separate differential transmit and receive paths, allowing a device to transmit and receive simultaneously. TIA/EIA RS-485 compliance across the complete supply range helps maintain defined bus behavior as the supply changes.
The ADM3063E family's principal features include 3.0 V to 5.5 V operation, a selectable 1.62 V to 5.5 V VIO option, and ±12 kV IEC ESD protection on the bus pins. A 500 kbps data rate supports factory automation, industrial control, building systems, and instrumentation links. The separate VIO supply allows the digital interface voltage to be selected independently from the transceiver supply, simplifying integration with processors operating at lower logic levels.
The manufacturer describes the ADM3063E as suitable for new designs and indicates that it is fully compatible with hot-swapping power-up and power-down without introducing glitches. Its protection features are aimed at industrial wiring where cables and external equipment can expose the interface to electrostatic discharge. The 14-lead SOIC_N package is a conventional surface-mount industrial option, while the family's related devices are also offered in smaller 8-lead and 10-lead packages and in LFCSP packages.
Typical applications include full-duplex industrial RS-485 links, programmable logic controller communication, factory automation equipment, building-control networks, and embedded instrumentation. The 500 kbps maximum signaling rate is appropriate for moderate-distance bus networks and point-to-point full-duplex links where simultaneous transmission and reception are required. The product family is also suitable for designs requiring hot-plug behavior when connected equipment is powered up or removed.
PCB implementation should preserve the transceiver's supply and logic pin assignments, place decoupling capacitors close to the device, and route the differential bus as a controlled impedance pair. External protection, termination, and biasing remain topology-dependent and should be designed against the actual cable length, node count, grounding method, and required common-mode margin. The manufacturer datasheet and pin-description table should govern final board connections.
This product data combines the manufacturer's device positioning with verified package, voltage, speed, ESD, lifecycle, and environmental information. It also organizes drop-in family alternatives, parameter comparisons, interface design notes, and application guidance so engineers can evaluate the ADM3063EARZ against the electrical and mechanical requirements of a specific RS-485 design.
חלופות תחליף ישיר עבור ADM3063EARZ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ADM3063EARZ (אותו גורם צורה וטביעת רגל) — שונים ב Interface Standard, Operating Temperature Range, Package, RoHS Status.
ADM3063EBRZ-R7
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
ADM3063EARZ-R7
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
ADM3064EARZ
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←ADM3065EARZ
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
ADM3066EARZ
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
ADM3063EARZ מפרטים
| Product Type | Full-duplex RS-485 transceiver |
| קצב נתונים | 500 kbps |
| VCC Operating Voltage Range | 3.0 V to 5.5 V |
| VIO Operating Voltage Range | 1.62 V to 5.5 V |
| Interface Standard | TIA/EIA RS-485 |
| Bus Configuration | Full duplex |
| ESD Contact Discharge Protection | At least ±12 kV per IEC 61000-4-2 |
| ESD Air Discharge Protection | At least ±12 kV per IEC 61000-4-2 |
| HBM ESD Protection | At least ±30 kV |
| מארז | 14-lead SOIC_N |
| סוג הרכבה | Surface mount |
| טווח טמפרטורת פעולה | -40°C to +85°C or -40°C to +125°C, model-dependent |
| Moisture Sensitivity Level | MSL 1 |
| סטטוס RoHS | RoHS3 compliant |
| REACH Status | Unaffected |
| Lifecycle Recommendation | Recommended for new designs |
| Hot-Swap Behavior | Glitch-free power-up and power-down |
| Number of Bus Pins | 4 bus pins |
| Number of Leads | 14 leads |
מדריך תצורת פינים של ADM3063EARZ 14-lead soic_n
תצורת פינים עבור ADM3063EARZ (מארזת 14-lead soic_n). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור ADM3063EARZ.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
ADM3063EARZ מתאים עבור 6 יישוםs: PLC Industrial Communication, Factory Automation Equipment, Building Control Network, Industrial Instrumentation, Hot-Pluggable Field Equipment, Embedded Data Acquisition.
PLC Industrial Communication
The ADM3063EARZ suits a full-duplex PLC communication port requiring 500 kbps RS-485 operation and a separate logic supply for the controller interface. Its 3.0 V to 5.5 V VCC range supports regulated industrial supplies, while the 1.62 V to 5.5 V VIO range can accommodate lower-voltage digital logic. Bus-pin ESD protection of at least ±12 kV for IEC 61000-4-2 contact discharge is valuable when the transceiver connects to field wiring. Use separate transmit and receive pairs, place local decoupling close to the device, and design termination and common-mode protection for the actual cable topology.
מומלץ
Factory Automation Equipment
The ADM3063EARZ can connect automation equipment to a full-duplex RS-485 field bus while preserving simultaneous command and response traffic. Its 500 kbps rate is appropriate for moderate-speed machine control and sensor networks, and the 14-lead SOIC_N package supports conventional surface-mount assembly. The specified hot-swap power-up and power-down behavior helps limit unwanted bus disturbance when connected equipment changes power state. External protection should be coordinated with the transceiver's bus-pin ESD rating, and differential routing should use a consistent pair geometry to minimize radiated emissions and susceptibility to industrial interference.
מומלץ
Building Control Network
For building-control equipment, the ADM3063EARZ provides a full-duplex RS-485 physical interface with logic-voltage flexibility and enhanced ESD protection on externally accessible conductors. The 1.62 V to 5.5 V VIO option supports integration with low-voltage building-controller logic, while the 500 kbps rate is suitable for supervisory control and sensor traffic. The design should maintain a defined reference ground, avoid excessive cable length, and apply termination only where required by the network topology. Protective devices should be placed near the connector so transient energy is diverted before reaching the transceiver.
מומלץ
Industrial Instrumentation
The ADM3063EARZ fits instrument-to-controller links where both directions of RS-485 data must remain active. A 500 kbps link rate supports measurement commands, status updates, and diagnostic information without requiring the highest bandwidth available from faster transceivers. The independent VIO supply allows the digital side to match the instrument's processor or controller directly, reducing level-shifting components. For reliable operation, place VCC and VIO bypass capacitors at their corresponding pins, route the differential bus away from switching nodes, and verify common-mode voltage at the receiver under worst-case cable and grounding conditions.
מומלץ
Hot-Pluggable Field Equipment
The ADM3063EARZ is appropriate for field equipment that may be powered up or powered down while connected to a live RS-485 network. Analog Devices specifically describes the ADM3063E family as compatible with hot-swapping without introducing glitches during power-up or power-down. This behavior helps reduce unwanted commands or state changes when a peripheral is inserted or removed. System designers should still control bus enable behavior, maintain the specified supply sequencing, and test the complete interface because external protection components, termination, and connector construction also influence the observed transient performance.
מומלץ
Embedded Data Acquisition
The ADM3063EARZ can serve as the communications interface in a distributed data-acquisition module that exchanges sampled data with a supervisory controller. Full-duplex operation permits continuous command reception while telemetry is transmitted, and the 500 kbps rate is suitable for many sensor and test-data streams. Its 14-lead SOIC_N package provides a straightforward industrial PCB footprint, while the selectable logic supply supports a range of embedded processors. Layout should keep the receiver path away from high-current switching stages, use a solid ground strategy, and follow the datasheet's external network recommendations for biasing and termination.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ADM3063EARZ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ADM3063EBRZ-R7 | ADM3063EARZ-R7 | ADM3064EARZ | ADM3065EARZ | ADM3066EARZ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Product Type | Full-duplex RS-485 transceiver | Full-duplex RS-485 transceiver | Full-duplex RS-485 transceiver | ADM3064E family RS-485 transceiver | ADM3065E family RS-485 transceiver | ADM3066E family RS-485 transceiver |
| VCC Operating Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V family range | 3.0 V to 5.5 V family range | 3.0 V to 5.5 V family range |
מבדילים עיקריים
- Independent low-voltage logic interface (לעומתADM3063EBRZ-R7)
- Full-duplex operation at 500 kbps (לעומתADM3064EARZ)
- Enhanced bus-pin ESD protection (לעומתADM3065EARZ)
- Glitch-free power-state transitions (לעומתADM3066EARZ)
הערות תכנון
Place the VCC and VIO decoupling capacitors immediately adjacent to their respective supply pins, with the shortest possible ground-return paths. Route the RS-485 driver and receiver connections as differential pairs, maintaining continuous reference to the board ground plane where the system design permits it. Keep the interface away from high-current switching nodes and use a solid, low-impedance ground strategy to reduce common-mode conversion and susceptibility to industrial noise.
Do not substitute a half-duplex transceiver without redesigning the bus topology. A full-duplex ADM3063E normally uses separate driver and receiver differential pairs, unlike a half-duplex interface that multiplexes one pair and requires direction control. Also confirm that the connector, cable, grounding, external protection, and termination network are compatible with the transceiver's common-mode limits; successful communication at short distances does not guarantee performance on a long industrial bus.
Treat the two conductors of each differential pair as a controlled-impedance structure and avoid routing over splits in the ground plane. Avoid placing test-point stubs that create visible discontinuities on high-speed RS-485 edges. Because the bus can carry fast 500 kbps signaling with fast rise times, minimize connector branches and unnecessary trace length, and verify the completed board for radiated emissions and ESD susceptibility under its intended enclosure and cable configuration.
Observe the distinct VCC and VIO supply ranges: VCC operates from 3.0 V to 5.5 V, while VIO supports 1.62 V to 5.5 V. Do not assume that both pins may use any supply within the VCC range. Confirm the logic thresholds against the connected controller, maintain the required bypass capacitance, and use the manufacturer's power-up and power-down recommendations when the equipment can be connected to a live bus.
מידע על תאימות
The component is identified as RoHS3 compliant and REACH unaffected, with MSL 1. No manufacturer statement for AEC-Q100 qualification, lead-free status, halogen-free status, or conflict-minerals compliance was available for the exact ordering code.