ATMEGA88-20AU - 8-Bit AVR MCU 8KB Flash 20MHz | Microchip
MPN: ATMEGA88-20AU ✓ פעילATMEGA88-20AU סקירה
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters. The AVR family sits within the broader hierarchy of 8-bit MCUs, which in turn belong to the microcontroller class of embedded processors. The ATmega88 is built on Microchip's picoPower AVR RISC architecture, executing most instructions in a single clock cycle from 32 general-purpose working registers.
Key features include 8 KB ISP Flash with read-while-write capability, 1 KB SRAM, 512 B EEPROM, 23 general-purpose I/O lines, three flexible timer/counters with compare modes, an 8-channel 10-bit ADC, a programmable watchdog timer, and debugWIRE on-chip debugging. The device supports 20 MIPS at 20 MHz and offers multiple sleep modes for low-power operation.
The ATmega88 uses a Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and data access. Its 130-instruction set is optimized for C compiler efficiency, and the on-chip debugWIRE interface provides non-intrusive emulation using only the RESET pin, eliminating the need for a dedicated debug header.
Typical applications include consumer electronics, industrial control, battery management, sensor nodes, and legacy ATmega8 design migrations. The 32-TQFP package with 0.8 mm pitch suits automated assembly, and the wide 2.7-5.5 V supply range supports both 3.3 V and 5 V systems.
When designing with this device, decouple VCC and AVCC with 100 nF ceramic capacitors placed close to the pins, and connect the AREF pin through a low-impedance path when using the ADC. The RESET pin requires an external pull-up for reliable power-on reset.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for selection, replacement, and layout decisions.
חלופות תחליף ישיר עבור ATMEGA88-20AU — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ATMEGA88-20AU (אותו גורם צורה וטביעת רגל) — שונים ב Package, RoHS Status, ADC, Timers, Operating Temperature.
ATMEGA88P-20AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88A-AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88-20AUR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
ATMEGA88V-10AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA168-20AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA48-20AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88-20AU דירוגים מרביים ומאפיינים חשמליים
| Core Architecture | 8-bit AVR RISC |
| Program Memory Size | 8 KB (4K x 16) Flash |
| SRAM | 1 KB |
| EEPROM | 512 B |
| תדר שעון מקסימלי | 20 MHz |
| Throughput | 20 MIPS at 20 MHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| General Purpose I/O Lines | 23 |
| General Purpose Working Registers | 32 |
| ADC Channels | 8-channel, 10-bit |
| Timer/Counters | Three flexible timer/counters with compare modes |
| מארז | 32-TQFP (7x7 mm, 0.8 mm pitch) |
| סוג הרכבה | Surface Mount |
| טמפרטורת פעולה | -40C to +85C |
| Instruction Set | 130 powerful instructions, most single-clock cycle |
| Debug Interface | debugWIRE on-chip debugging |
| סטטוס RoHS | Compliant |
| Life Cycle Stage | ACTIVE |
תצורת פינים של ATMEGA88-20AU
| פין 1 | PB0 — Port B, bit 0 (also ICP1) |
| פין 2 | PB1 — Port B, bit 1 (also OC1A) |
| פין 3 | PB2 — Port B, bit 2 (also SS/OC1B) |
| פין 4 | PB3 — Port B, bit 3 (also MOSI/OC2A) |
| פין 5 | PB4 — Port B, bit 4 (also MISO) |
| פין 6 | PB5 — Port B, bit 5 (also SCK) |
| פין 7 | PB6 — Port B, bit 6 (also XTAL1/TOSC1) |
| פין 8 | PB7 — Port B, bit 7 (also XTAL2/TOSC2) |
| פין 9 | RESET — Reset input (active low) |
| פין 10 | VCC — Digital supply voltage |
| פין 11 | GND — Ground |
| פין 12 | XTAL2 — Crystal oscillator output |
| פין 13 | XTAL1 — Crystal oscillator input |
| פין 14 | PD0 — Port D, bit 0 (also RXD) |
| פין 15 | PD1 — Port D, bit 1 (also TXD) |
| פין 16 | PD2 — Port D, bit 2 (also INT0) |
| פין 17 | PD3 — Port D, bit 3 (also INT1/OC2B) |
| פין 18 | PD4 — Port D, bit 4 (also T0/XCK) |
| פין 19 | PD5 — Port D, bit 5 (also T1/OC0B) |
| פין 20 | PD6 — Port D, bit 6 (also AIN0/OC0A) |
| פין 21 | PD7 — Port D, bit 7 (also AIN1) |
| פין 22 | PC0 — Port C, bit 0 (also ADC0) |
| פין 23 | PC1 — Port C, bit 1 (also ADC1) |
| פין 24 | PC2 — Port C, bit 2 (also ADC2) |
| פין 25 | PC3 — Port C, bit 3 (also ADC3) |
| פין 26 | PC4 — Port C, bit 4 (also ADC4/SDA) |
| פין 27 | PC5 — Port C, bit 5 (also ADC5/SCL) |
| פין 28 | PC6 — Port C, bit 6 (also RESET) |
| פין 29 | AREF — Analog reference voltage for ADC |
| פין 30 | AVCC — Analog supply voltage for ADC |
| פין 31 | GND — Ground |
| פין 32 | PC7 — Port C, bit 7 (also ADC7) |
יישומים טיפוסיים
ATMEGA88-20AU מתאים עבור 6 יישוםs: Consumer Electronics Control, Industrial Sensor Nodes, Battery-Powered Portable Devices, Legacy ATmega8 Design Migration, Motor and Actuator Control, Embedded Data Logging.
Consumer Electronics Control
The ATMEGA88-20AU fits consumer electronics control because its 8 KB Flash and 23 GPIO lines handle user-interface logic, button scanning, and LED driving without external glue logic. Running at 20 MHz for 20 MIPS, it executes control loops fast enough for appliance front panels and remote-control receivers. The 2.7-5.5 V supply range allows direct operation from either 3.3 V or 5 V rails, simplifying power architecture. Placed on a 32-TQFP footprint, it occupies only 7x7 mm, leaving board space for RF or display modules. A trade-off is that the 8 KB Flash limits complex menu systems; designs needing graphics or large lookup tables should migrate to the pin-compatible ATMEGA168-20AU with 16 KB Flash.
מומלץ
Industrial Sensor Nodes
The ATMEGA88-20AU suits industrial sensor nodes because its 8-channel 10-bit ADC digitizes analog transducer outputs directly, eliminating external ADC chips. The 23 GPIO lines interface with digital sensors, relays, and status LEDs, while three timer/counters generate precise PWM for actuator control. Operating from 2.7 V to 5.5 V, it tolerates the noisy supply rails common in factory automation. The debugWIRE interface allows in-circuit debugging through the RESET pin, reducing production connector cost. In a typical node, the MCU samples a temperature or pressure sensor at 1 kHz, filters the reading, and transmits over UART or SPI. The main limitation is the 1 KB SRAM, which constrains buffer-heavy protocols; designs with large data payloads should consider the ATMEGA168-20AU.
מומלץ
Battery-Powered Portable Devices
The ATMEGA88-20AU works in battery-powered portable devices because it operates down to 2.7 V, extending usable life from 3.7 V Li-ion cells, and offers multiple sleep modes that cut current between active periods. At 20 MHz it delivers 20 MIPS for responsive user interaction, then drops to microamp-level sleep to preserve charge. The 8 KB Flash stores application code plus a boot loader for field updates, and 512 B EEPROM retains calibration data without external memory. A typical design wakes the MCU on a button or timer interrupt, performs a measurement, updates a display, and returns to sleep. For the lowest possible current, the pin-compatible ATMEGA88P-20AU with picoPower technology is the better choice, reducing active and sleep currents further.
מומלץ
Legacy ATmega8 Design Migration
The ATMEGA88-20AU is a common migration target for legacy ATmega8 designs because Microchip application note AVR094 documents the conversion path and the two devices are pin compatible in the 32-pin TQFP package. The ATmega88 adds read-while-write Flash, more timer features, and a richer peripheral set while retaining the familiar AVR instruction set, so existing assembly or C code ports with minimal changes. The 8 KB Flash matches the ATmega8 capacity, and the 20 MHz speed grade preserves timing margins. Engineers migrating should re-validate fuse settings, interrupt vector tables, and register names that changed between families. For designs that outgrew the ATmega8, the pin-compatible ATMEGA168-20AU doubles Flash to 16 KB without a PCB change.
מומלץ
Motor and Actuator Control
The ATMEGA88-20AU handles motor and actuator control because its three timer/counters generate multiple independent PWM channels for H-bridge or stepper drivers, while the 10-bit ADC reads current-sense and position feedback signals. At 20 MHz, the control loop closes fast enough for small brushed DC motors and stepper positioning in printers, toys, and lab equipment. The 23 GPIO lines drive direction, enable, and fault signals directly. A typical implementation uses Timer1 in fast PWM mode for speed control and the ADC to monitor motor current for stall detection. The 8 KB Flash is adequate for trapezoidal or simple PID control; complex field-oriented control for BLDC motors would require the larger ATMEGA168-20AU or a dedicated motor-control MCU.
מומלץ
Embedded Data Logging
The ATMEGA88-20AU supports embedded data logging because its 512 B EEPROM stores calibration constants and configuration without external memory, while the 1 KB SRAM buffers sensor samples before writing to an external SPI Flash or SD card. The 8-channel 10-bit ADC captures analog inputs, and the UART or SPI interface streams logged data to a host. Running at 20 MHz, the MCU can sample and timestamp data at kilohertz rates. A typical logger wakes on a timer, reads several ADC channels, stores readings in a ring buffer, and periodically flushes to non-volatile storage. The 8 KB program Flash limits the complexity of on-device compression or file-system code; designs needing FAT file systems should use the pin-compatible ATMEGA168-20AU with 16 KB Flash.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ATMEGA88-20AU — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ATMEGA88P-20AU | ATMEGA88A-AU | ATMEGA168-20AU | ATMEGA48-20AU |
|---|---|---|---|---|---|
| Package | 32-TQFP (7x7) | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 8 KB | 8 KB | 8 KB | 16 KB | 4 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 512 B |
| EEPROM | 512 B | 512 B | 512 B | 512 B | 256 B |
| Maximum Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage | 2.7 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| GPIO Lines | 23 | 23 | 23 | 23 | 23 |
| ADC Channels | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit |
| Low-Power Technology | Standard AVR | picoPower | picoPower | Standard AVR | Standard AVR |
מבדילים עיקריים
- Standard AVR power profile vs picoPower (לעומתATMEGA88P-20AU)
- 8 KB Flash balance vs larger and smaller siblings (לעומתATMEGA168-20AU)
- 20 MHz speed grade vs 10 MHz V-variant (לעומתATMEGA88V-10AU)
הערות תכנון
Decouple both VCC (pin 10) and AVCC (pin 30) with 100 nF ceramic capacitors placed as close to the pins as possible, and add a 10 uF bulk capacitor on the board rail. AVCC must be connected even when the ADC is unused. For ADC accuracy, connect AREF through a low-impedance path and avoid sharing the analog ground return with high-current digital traces. Estimated: at 20 MHz and 5 V, core current is on the order of several milliamps, so a 100 nF decoupling capacitor per supply pin is sufficient for typical loads.
Route the crystal between XTAL1 (pin 13) and XTAL2 (pin 12) with the shortest possible traces and place the load capacitors symmetrically to ground. Keep the crystal away from switching nodes and clock lines. The RESET pin (pin 9) requires an external pull-up resistor, typically 10 kOhm, and a 100 nF capacitor to ground for noise immunity. The debugWIRE interface shares the RESET pin, so ensure the programmer can drive it without contention from the pull-up.
Do not leave AVCC unconnected, as this can cause erratic ADC readings and increased current consumption. Verify the fuse settings for the clock source before production; the default factory fuse may select the internal 8 MHz oscillator rather than an external crystal. When migrating from ATmega8, re-check interrupt vector addresses and register names, as Microchip application note AVR094 documents several differences. Always confirm the speed-grade voltage curve in the manufacturer datasheet, since the 20 MHz rating may require a higher minimum supply than the 2.7 V absolute minimum.
מידע על תאימות
RoHS compliance is indicated by distributor listings. REACH, halogen-free, and conflict-minerals status were not stated in the provided data and are marked unknown. The device is not AEC-Q100 qualified; automotive designs should use an automotive-grade variant.
