ATMEGA88-20AI - 8-bit AVR MCU 20MHz 8KB Flash TQFP-32 | Microchip
MPN: ATMEGA88-20AI ✓ פעילATMEGA88-20AI סקירה
An 8-bit AVR microcontroller is a single-chip computer that executes an advanced RISC instruction set, combining program memory, data memory, timers, analog-to-digital conversion, and serial communication peripherals on one die. Within the power-management hierarchy of embedded systems, the ATmega family sits at the entry-to-mid range of Microchip (formerly Atmel) MCU offerings, below the ATmega328 and ATmega2560 families.
Key features include 131 powerful instructions with mostly single-cycle execution, 32 general purpose working registers, 23 general purpose I/O lines, and picoPower technology for low static power consumption. On-chip peripherals comprise three flexible timer/counters with compare modes, a 10-bit 8-channel ADC, a programmable serial USART, a byte-oriented Two-Wire Interface (TWI/I2C), and an SPI serial port.
Technical depth comes from the AVR Harvard architecture with single-level pipelining, allowing one instruction per clock cycle. The device supports DebugWIRE on-chip debugging through the reset line, In-System Programming (ISP) with read-while-write Flash, and offers brown-out detection, power-on reset, and internal calibrated RC oscillator options at 8 MHz and 128 kHz. Operation spans 1.8 V to 5.5 V with 20 MHz performance guaranteed at 4.5 V to 5.5 V.
Typical applications include industrial sensor nodes and motor control boards (the industrial -40C to +85C temperature grade suits factory environments), consumer appliance user interfaces, and battery-powered instrumentation where picoPower sleep modes extend battery life.
A key design consideration: maximum clock frequency scales with VCC - 20 MHz is only guaranteed above 4.5 V, so designs running at 3.3 V must limit the clock to roughly 13.3 MHz or account for derating.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-09-19.
חלופות תחליף ישיר עבור ATMEGA88-20AI — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ATMEGA88-20AI (אותו גורם צורה וטביעת רגל) — שונים ב Package, Throughput, Operating Temperature, Communication Interfaces, Supply Voltage Range.
ATMEGA88-20AU
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88P-20AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88A-20AU
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
ATMEGA48-20AU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88-15AT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88-15AD
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA88-20AI דירוגים מרביים ומאפיינים חשמליים
| Core Processor | AVR 8-bit RISC |
| Core Size | 8-bit |
| Speed | 20 MHz |
| Flash Program Memory | 8 KB (4K x 16) |
| EEPROM | 512 B |
| SRAM | 1 KB |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Max Clock at Full Voltage | 20 MHz at 4.5 V to 5.5 V |
| GPIO Count | 23 |
| ADC Resolution | 10-bit, 8 channels |
| Communication Interfaces | USART, SPI, TWI (I2C) |
| Timers | Two 8-bit, one 16-bit |
| MIPS Throughput | Up to 20 MIPS at 20 MHz |
| טמפרטורת פעולה | -40C to +85C |
| מארז | 32-TQFP (7x7 mm) |
| סוג הרכבה | Surface Mount |
| On-Chip Debug | DebugWIRE |
| Programming | ISP, read-while-write Flash |
| Reset/Brown-out | Power-on Reset, Brown-out Detect/Reset |
תצורת פינים של ATMEGA88-20AI
| פין 1 | PD3 (PCINT19/OC2B/INT1) — Port D bit 3, pin-change interrupt, Timer2 output compare B, external interrupt 1 |
| פין 2 | PD4 (PCINT20/XCK/T0) — Port D bit 4, pin-change interrupt, USART external clock, Timer0 clock input |
| פין 3 | GND — Ground |
| פין 4 | VCC — Digital supply voltage |
| פין 5 | GND — Ground |
| פין 6 | VCC — Digital supply voltage |
| פין 7 | PB6 (PCINT6/XTAL1/TOSC1) — Port B bit 6; crystal oscillator pin 1 or timer oscillator input |
| פין 8 | PB7 (PCINT7/XTAL2/TOSC2) — Port B bit 7; crystal oscillator pin 2 or timer oscillator output |
| פין 9 | PD5 (PCINT21/OC0B/T1) — Port D bit 5, pin-change interrupt, Timer0 output compare B, Timer1 clock input |
| פין 10 | PD6 (PCINT22/OC0A/AIN0) — Port D bit 6, Timer0 output compare A, analog comparator positive input |
| פין 11 | PD7 (PCINT23/AIN1) — Port D bit 7, analog comparator negative input |
| פין 12 | PB0 (PCINT0/CLKO/ICP1) — Port B bit 0, system clock output, Timer1 input capture |
| פין 13 | PB1 (PCINT1/OC1A) — Port B bit 1, Timer1 output compare A (PWM) |
| פין 14 | PB2 (PCINT2/SS/OC1B) — Port B bit 2, SPI slave select, Timer1 output compare B |
| פין 15 | PB3 (PCINT3/OC2A/MOSI) — Port B bit 3, Timer2 output compare A, SPI master output |
| פין 16 | PB4 (PCINT4/MISO) — Port B bit 4, SPI master input |
| פין 17 | PB5 (PCINT5/SCK) — Port B bit 5, SPI serial clock |
| פין 18 | AVCC — ADC supply voltage |
| פין 19 | ADC6 — ADC input channel 6 (dedicated analog input) |
| פין 20 | AREF — Analog reference voltage for ADC |
| פין 21 | GND — Ground |
| פין 22 | ADC7 — ADC input channel 7 (dedicated analog input) |
| פין 23 | PC0 (PCINT8/ADC0) — Port C bit 0, pin-change interrupt, ADC channel 0 |
| פין 24 | PC1 (PCINT9/ADC1) — Port C bit 1, pin-change interrupt, ADC channel 1 |
| פין 25 | PC2 (PCINT10/ADC2) — Port C bit 2, pin-change interrupt, ADC channel 2 |
| פין 26 | PC3 (PCINT11/ADC3) — Port C bit 3, pin-change interrupt, ADC channel 3 |
| פין 27 | PC4 (PCINT12/SDA/ADC4) — Port C bit 4, TWI data line, ADC channel 4 |
| פין 28 | PC5 (PCINT13/SCL/ADC5) — Port C bit 5, TWI clock line, ADC channel 5 |
| פין 29 | PC6 (PCINT14/RESET) — Reset input / DebugWIRE line; active-low with internal pull-up |
| פין 30 | PD0 (PCINT16/RXD) — Port D bit 0, USART receiver input |
| פין 31 | PD1 (PCINT17/TXD) — Port D bit 1, USART transmitter output |
| פין 32 | PD2 (PCINT18/INT0) — Port D bit 2, external interrupt 0 |
יישומים טיפוסיים
ATMEGA88-20AI מתאים עבור 6 יישוםs: Industrial Sensor Nodes, Motor Control and Actuator Boards, Consumer Appliance UI Boards, Battery-Powered Portable Instrumentation, Embedded Serial-to-Protocol Bridges, HVAC and Environmental Control.
Industrial Sensor Nodes
The ATMEGA88-20AI fits industrial sensor nodes because its -40C to +85C grade survives factory-floor temperature swings, and its 10-bit 8-channel ADC digitizes multiple analog sensors (pressure, temperature bridges, potentiometers) without external conversion hardware. In a typical node, the MCU samples sensors through the ADC, applies linearization in the 8 KB Flash, and streams readings over the USART or TWI bus to a gateway at up to 20 MIPS throughput. PicoPower sleep modes reduce idle current between periodic samples, and the brown-out detector guards against data corruption during supply sags common in long cable runs. Budget roughly 8 KB for code and 1 KB for buffers and protocol state.
מומלץ
Motor Control and Actuator Boards
Small brushed-DC and stepper motor boards benefit from the ATMEGA88-20AI's three timer/counters (two 8-bit, one 16-bit) that generate independent PWM channels with compare modes, while the 16-bit timer provides precise speed measurement via input capture. At 20 MHz the core delivers 20 MIPS, sufficient for closed-loop PI control at kilohertz loop rates. The 23 GPIO lines drive H-bridge gate circuitry through the port registers, and the 10-bit ADC reads back current-sense shunt voltages for torque limiting. In-system programming allows field firmware updates of control profiles without removing the board, and the industrial temperature rating suits enclosed motor-driver enclosures with limited airflow.
מומלץ
Consumer Appliance UI Boards
Washer, oven, and HVAC front-panel controllers are a classic ATmega88 use case: the MCU scans keypads via GPIO interrupts, drives segment LCDs or LEDs with timer PWM dimming, and manages buzzer feedback, all within 1 KB SRAM and 8 KB Flash. The internal 8 MHz calibrated RC oscillator removes the crystal and its cost from cost-sensitive boards, while the TWI interface talks to external EEPROM or touch controllers. The 1.8-5.5 V range tolerates unregulated transformer-derived supplies, and the brown-out reset prevents corrupted settings during brownout events. Industrial-grade temperature tolerance also adds margin in hot appliance interiors near heating elements.
מומלץ
Battery-Powered Portable Instrumentation
Handheld meters and loggers exploit the ATMEGA88-20AI's 1.8 V minimum supply to run directly from two alkaline cells (3.0 V nominal) to end-of-life at 1.8 V, and its picoPower sleep modes - Power-down in particular - drop current to microamp levels between measurements. The ADC Noise Reduction mode lets conversions run with the CPU clock stopped, improving analog accuracy in noisy motor-driven environments. Designers should clock the part at roughly 8 MHz or less when operating at 3 V, since the 20 MHz rating applies only from 4.5 V to 5.5 V. The 512 B EEPROM preserves calibration constants and logged min/max data across battery changes.
מומלץ
Embedded Serial-to-Protocol Bridges
The ATMEGA88-20AI converts between serial protocols using its hardware USART, SPI, and TWI interfaces running concurrently. A common bridge topology accepts RS-232/RS-485 frames on the USART, parses them in the 1 KB SRAM buffer, and relays register data to TWI peripherals (RTC, DAC, port expanders) or SPI devices (Flash, sensors) at 20 MIPS execution speed. Hardware flow control and framing-error detection in the USART improve link robustness in electrically noisy cabinets. Self-programming Flash supports bootloader-based firmware field upgrades over the serial link itself, letting deployed bridges receive protocol updates without physical access - a key advantage in installed industrial wiring harnesses.
מומלץ
HVAC and Environmental Control
Thermostat and ventilation controllers pair the ATMEGA88-20AI's 10-bit ADC with NTC thermistor dividers for multi-zone temperature sensing, while timer PWM drives tripper or triac outputs for damper motors and fan speed control. The Power-save sleep mode with the asynchronous timer allows the MCU to wake on a 32.768 kHz crystal timebase for timed schedules, conserving power between wake events. TWI connects external humidity or CO2 sensors, and the industrial -40C to +85C rating covers rooftop equipment enclosures. With only 8 KB of Flash, control logic and a simple UI state machine must be coded efficiently, but no RTOS overhead is needed.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ATMEGA88-20AI — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ATMEGA88-20AU | ATMEGA88P-20AU | ATMEGA48-20AU |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP (7x7 mm) | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same |
| Flash Memory | 8 KB | 8 KB | 8 KB | 4 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 512 B |
| EEPROM | 512 B | 512 B | 512 B | 256 B |
| Max Clock Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Sleep-Mode Power | Standard AVR sleep modes | Standard AVR sleep modes | picoPower - lowest sleep current | Standard AVR sleep modes |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
| Operating Temperature | -40C to +85C (industrial) | Industrial grade | Industrial grade | Industrial grade |
מבדילים עיקריים
- Full 8 KB Flash with self-programming bootloader support (לעומתATMEGA48-20AU)
- Lowest long-term power option is the P-variant (לעומתATMEGA88P-20AU)
- 20 MHz speed grade for headroom-critical control loops (לעומתATMEGA88-15AT)
- Industrial temperature grade as standard (לעומתCommercial-grade TQFP variants)
הערות תכנון
Respect the clock-versus-voltage derating: the ATMEGA88-20AI guarantees 20 MHz only from 4.5 V to 5.5 V. At 3.3 V the safe ceiling is roughly 13.3 MHz (estimated: linear 0.9-20 MHz/V interpolation from the datasheet speed-grade curves). Running a full 20 MHz crystal on a 3.3 V rail risks out-of-spec execution and flash-write errors. If your design must run 3.3 V at high speed, either lower the crystal to 12-13 MHz or level-shift to a 5 V supply. Verify against the current Microchip ATmega88 datasheet speed curves before finalizing.
Place a 100 nF ceramic decoupling capacitor across each VCC/GND pin pair (pins 4-3 and 6-5) within 2 mm of the pins, plus a 100 nF cap on AVCC (pin 18) with a 10 uH series inductor or ferrite bead from VCC to AVCC to isolate ADC noise. Tie AREF (pin 20) to ground through 100 nF when using internal reference, or filter the external reference. Connect AVCC to VCC even if the ADC is unused - the datasheet requires AVCC present for correct digital operation.
PC6/RESET (pin 29) doubles as the DebugWIRE interface - enabling DebugWIRE via the DWEN fuse disables external reset, and recovering requires a high-voltage parallel programmer. Always keep ISP header access (PB3/MOSI, PB4/MISO, PB5/SCK, RESET) on production boards for field firmware updates. When using PB6/PB7 as GPIO instead of a crystal, confirm the CKOUT/fuse settings; wrong fuse programming of the clock source is the most common cause of 'bricked' ATmega88 boards.
At 5 V and 20 MHz with GPIO loads of 20 mA per pin, estimated worst-case power dissipation stays under 0.5 W, and the 32-TQFP theta_JA of approximately 100 C/W (typical 7x7 TQFP on 4-layer board - verify in package datasheet) yields under 50 C junction rise, safe at +85 C ambient. Avoid loading many I/O pins to their 40 mA absolute maximum simultaneously; the total device current limit governs, not the per-pin rating.
מידע על תאימות
RoHS and lead-free status per standard Microchip commercial MCU offering; verify REACH and conflict-minerals declarations on the Microchip product compliance portal for this exact ordering code.
