CD4518BF3 Dual BCD Up-Counter, 16-CDIP | Harris
MPN: CD4518BF3 ⚠ רכישה אחרונהCD4518BF3 סקירה
A BCD counter is a digital counter that represents decimal digits using a four-bit binary-coded decimal output. The dual counter belongs to the broader CMOS logic hierarchy: counter IC, logic IC, digital integrated circuit, and semiconductor. The CD4518 is useful when a design must count decimal events, divide an input frequency, sequence industrial equipment, or generate multi-digit numerical displays without requiring a microcontroller.
Key operating features include medium-speed operation, a typical 6 MHz clock at a 10 V supply, selectable positive- or negative-edge triggering, and synchronous internal carry propagation. The dual architecture supports two independent 4-bit counters in decimal mode or two 4-bit binary counters. Its broad supply range allows operation from 3 V through 18 V, making it suitable for both 5 V and higher-voltage industrial logic systems when signal and input tolerances are checked carefully.
The CD4518BF3 uses CMOS construction to provide low quiescent current and wide operating-voltage capability. Its maximum input current is specified as 1 uA at 18 V, and the device is 100% tested for quiescent current at 20 V over the full package-temperature range. As a legacy ceramic-DIP device, it offers a robust through-hole construction for industrial, laboratory, educational, and maintenance applications rather than a compact surface-mount footprint.
Typical uses include decade counters for panel meters, frequency dividers in timing circuits, programmable sequence controllers, digital time-base modules, and two-digit event counters. Two CD4518 packages can also form an eight-bit cascaded counter when the carry output of the first device clocks the second. Designers should treat all unused CMOS inputs as active logic states and observe the manufacturer's truth table for reset and count-trigger behavior.
For reliable operation, connect the reset inputs to a defined logic level and do not allow unused inputs to float. Decoupling should follow the manufacturer datasheet's recommended supply arrangement, while external clock and reset traces should be kept short and protected from switching-node coupling. The ceramic DIP package permits straightforward breadboard and through-hole construction, but its 0.300-inch, 7.62 mm pin pitch requires a compatible footprint and adequate board spacing.
This product page combines the CD4518BF3 electrical characteristics, pin configuration, verified family references, compatible counter alternatives, comparison parameters, and practical implementation guidance to support component selection, schematic review, PCB footprint confirmation, and legacy-system maintenance.
חלופות תחליף ישיר עבור CD4518BF3 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם CD4518BF3 (אותו גורם צורה וטביעת רגל) — שונים ב Logic Family, Clock Edge Selection, Carry Propagation, Maximum Input Current, Operating Temperature Range.
CD4518BE
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC14518B
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
CD4518BF3A
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
HCF4518B
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
HEF4518B
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
CD4518BF3 דירוגים מרביים ומאפיינים חשמליים
| Product Type | Dual BCD up-counter |
| Number of Counters | 2 counters |
| Counter Resolution | 4 bits per counter |
| Counting Modes | BCD decimal or binary |
| Supply Voltage Range | 3 V to 18 V |
| Typical Clock Frequency | 6 MHz at 10 V |
| Clock Edge Selection | Positive- or negative-edge triggering |
| Carry Propagation | Synchronous internal |
| Maximum Input Current | 1 uA at 18 V |
| Quiescent Current Test | 100% tested at 20 V over full package-temperature range |
| Logic Family | CMOS |
| מארז | 16-CDIP, 0.300-inch (7.62 mm) pitch |
| סוג הרכבה | Through-hole |
| מספר פינים | 16 pins |
| תצורת מוצא | Dual 4-bit BCD/binary counter outputs |
מדריך תצורת פינים של CD4518BF3 16-cdip, 0.300-inch (7.62 mm) pitch
תצורת פינים עבור CD4518BF3 (מארזת 16-cdip, 0.300-inch (7.62 mm) pitch). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור CD4518BF3.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
CD4518BF3 מתאים עבור 6 יישוםs: Industrial Digital Sequence Counter, Panel-Meter Digit Counter, Frequency Divider and Timer, Laboratory Counter and Pulse-Counter, Two-Digit Event Display, Legacy Control and Automation Module.
Industrial Digital Sequence Counter
The CD4518BF3 is suitable for industrial sequence counting because it combines two independent counters, selectable BCD or binary modes, and a 3 V to 18 V supply range. One section can count machine events while the other tracks a second process stage, eliminating the need for two separate counter packages. The 16-CDIP construction supports through-hole assembly and repair. At 10 V, the family is specified for a typical 6 MHz clock, allowing operation above simple event-rate counting when timing margins are verified. Use defined reset levels, avoid floating CMOS inputs, and route clock and reset lines away from high-current switching nodes.
מומלץ
Panel-Meter Digit Counter
The CD4518BF3 can form the counting stage of a decimal panel display because each half operates as a 4-bit BCD up-counter. Two sections permit separate decade digits, while cascaded operation can extend the count range. The BCD outputs reduce the logic required to decode decimal values and drive display-oriented circuitry. A 3 V to 18 V operating range permits integration into legacy industrial instruments operating near 5 V or at higher logic levels. The 16-CDIP package is easy to socket for maintenance, although designers should check LED or display drive currents and keep the counter supply adequately decoupled.
מומלץ
Frequency Divider and Timer
The CD4518BF3 is appropriate for frequency division and time-base generation because it supports both decimal and binary counting, selectable clock-edge triggering, and synchronous carry propagation. The manufacturer CD4518B family reaches a typical 6 MHz clock at 10 V, providing substantial margin for dividing lower-frequency timing inputs into slower system clocks. Configure the mode-control inputs from the four count outputs to establish the divide ratio, then cascade a second package when additional division is required. Confirm switching times across voltage and temperature before using the typical clock figure as a guaranteed system limit.
מומלץ
Laboratory Counter and Pulse-Counter
The CD4518BF3 works well as the core of a laboratory pulse-counter because two independent counter sections can monitor separate inputs without duplicating counter circuitry. Positive- or negative-edge triggering allows selection of the desired response to input transitions, while BCD mode simplifies decimal readout. The 16-CDIP package is convenient for breadboards and legacy educational or service equipment, and its 3 V minimum supply supports operation from a 5 V laboratory rail. A ceramic DIP package adds mechanical robustness, but reset inputs should still be debounced or controlled so switch bounce does not create unintended counts.
מומלץ
Two-Digit Event Display
The CD4518BF3 can count and retain two decimal digits for event displays, product counters, and batch-counting systems. Each 4-bit BCD section represents one decade, and the sections may be advanced independently or cascaded. The family operates from 3 V to 18 V, allowing use in legacy 5 V instrumentation as well as higher-voltage industrial logic where appropriate. Synchronous internal carry propagation helps define when the high-order digit advances. The ceramic DIP footprint requires a 0.300-inch, 7.62 mm pitch layout, and designers should account for output loading when adding display drivers or logic decoders.
מומלץ
Legacy Control and Automation Module
The CD4518BF3 can serve as a compact state-counting element in legacy industrial controls, particularly where a 16-pin through-hole footprint and wide supply range simplify retrofit work. Two counters can track separate steps, count retries, or implement a multi-stage timing sequence without adding a microcontroller. The device's CMOS inputs require valid logic levels, so unused terminals must not float and long wiring should be shielded from inductive or switching interference. Its 6 MHz typical clock at 10 V supports moderately fast event processing, but thermal, timing, and reset behavior must be checked against the original control system requirements.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור CD4518BF3 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | CD4518BE | MC14518B | CD4518BF3A | HCF4518B | HEF4518B |
|---|---|---|---|---|---|---|
| Package | 16-CDIP | 16-PDIP | 16-DIP | 16-CDIP | 16-DIP | 16-DIP |
| Brand | Harris Corporation | Texas Instruments | Motorola | Texas Instruments | STMicroelectronics | NXP Semiconductors |
| Counter Type | Dual BCD up-counter | Dual BCD up-counter | Equivalent dual 4518 BCD up-counter | Dual BCD up-counter | Equivalent 4518 CMOS counter | Equivalent 4518 CMOS counter |
| Number of Counters | 2 | 2 | 2 | 2 | 2 | 2 |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
מבדילים עיקריים
- Legacy ceramic-DIP construction for established through-hole assemblies (לעומתCD4518BE)
- Exact target-family configuration with a 6 MHz typical clock at 10 V (לעומתMC14518B)
- Broad 3 V to 18 V supply operation for legacy instrumentation (לעומתCD4518BF3A)
הערות תכנון
Do not leave unused CMOS inputs floating. Tie each unused clock, reset, and mode-control terminal to a valid inactive logic level so input leakage, coupling, and supply noise cannot create false transitions. Confirm the reset truth table before connecting external switches; a slow or noisy reset release may cause repeated or asynchronous count behavior. Use a defined pull-down or pull-up arrangement appropriate to the active state shown in the manufacturer datasheet.
The CD4518BF3 occupies a 16-pin, 0.300-inch, 7.62 mm pitch footprint. Confirm ceramic-DIP body width, row spacing, and drill size against the physical device before releasing artwork. Place the device away from high-current switching stages and route clock and reset traces as short nets. If the board also contains a CD4518BE plastic-DIP alternative, verify that the package body and drill geometry remain acceptable for the assembled board rather than checking pin count alone.
Supply decoupling must be located close to the CD4518BF3 power and ground terminals. Apply the manufacturer datasheet's recommended bypass capacitance and keep the ground return short to reduce clock-edge current in the supply rails. The family operates from 3 V to 18 V, but output rise time and maximum clock rate vary with supply voltage, so use the lowest valid supply only when its corresponding timing characteristics satisfy the design requirement.
מידע על תאימות
The CD4518BF3 is a legacy Harris Corporation ceramic-DIP logic IC. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact device.