DG405DJ+ - 45Ω Dual High-Speed Analog Switch | Analog Devices
MPN: DG405DJ+ ✓ פעילDG405DJ+ סקירה
A CMOS analog switch is a solid-state semiconductor device that routes analog or digital signals between circuit nodes using voltage-controlled gates. The DG405 family belongs to the broader analog-switch and multiplexer hierarchy, where switch topology, on-resistance, bandwidth, charge injection, and signal-to-noise performance determine whether a device is suitable for precision measurement, communications, instrumentation, or test systems. Unlike mechanical relays, these switches switch without moving contacts and can operate at much higher speeds.
The redesigned DG401, DG403, and DG405 family provides guaranteed on-resistance matching between switches of 2 Ω maximum and guaranteed on-resistance flatness over the signal range of 3 Ω maximum. The typical on-resistance is 20 Ω, while the product listing identifies a 45 Ω maximum on-resistance. These characteristics help reduce channel-to-channel error and distortion when a system switches between multiple signal sources or routes a signal to different measurement and processing circuits.
The DG405DJ+ uses CMOS circuitry to provide low power consumption and high switching speed. Each of its two channels can function as a 2:1 analog switch, enabling signal selection, channel isolation, test-point routing, and redundant signal paths. Its normally open configuration disconnects the common node while the control signal is inactive, helping prevent unwanted signal propagation when a channel is not selected.
Typical uses include audio and communications routing, data-acquisition systems, automated test equipment, sample-and-hold interfaces, and industrial control electronics. The device is particularly appropriate when the signal bandwidth and switching requirements exceed those of basic low-speed analog switches, while the 45 Ω maximum on-resistance remains acceptable for the driven load.
Designers should verify the complete electrical limits, control logic levels, switch configuration, and timing behavior in the manufacturer datasheet before finalizing signal paths. Input and output impedances, capacitance, and off-state leakage must be considered together with the 20 Ω typical on-resistance so that switching transients do not degrade accuracy or disturb adjacent high-impedance nodes.
This page consolidates the key DG405DJ+ electrical ratings, package information, drop-in identity options, application guidance, and design considerations into one engineering-focused reference. It supports faster component identification while keeping the selection grounded in the manufacturer datasheet and documented device characteristics.
חלופות תחליף ישיר עבור DG405DJ+ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
DG405DJ
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DG405DJ-E3
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DG405DJ
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DG405DJ+ דירוגים מרביים ומאפיינים חשמליים
| Number of Circuits | 2 circuits |
| Switch Configuration | 2:1 per channel |
| Maximum On-Resistance | 45 ohm |
| Typical On-Resistance | 20 ohm |
| On-Resistance Matching Between Switches | 2 ohm maximum |
| On-Resistance Flatness Over Signal Range | 3 ohm maximum |
| Technology | CMOS |
| Switch Type | Normally open |
| מספר פינים | 16 pins |
| Package Type | 16-pin PDIP |
| סוג הרכבה | Through-hole |
| Product Family | DG405 |
| Description | Improved dual high-speed analog switches |
| סטטוס RoHS | RoHS compliant |
| Lead-Free Status | Lead free |
מדריך תצורת פינים של DG405DJ+ 16-pin pdip
תצורת פינים עבור DG405DJ+ (מארזת 16-pin pdip). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור DG405DJ+.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
DG405DJ+ מתאים עבור 6 יישוםs: Automated Test Equipment Signal Routing, Data-Acquisition Multiplexing, Communications Signal Isolation, Audio Signal Switching, Industrial Control Signal Routing, Sample-and-Hold Interface.
Automated Test Equipment Signal Routing
The DG405DJ+ fits automated test systems that route one common measurement node to two possible signal sources or destinations. Its dual 2:1 architecture provides independent selection, while the 45 Ω maximum on-resistance gives designers a defined insertion-loss limit. The family’s 20 Ω typical on-resistance and 2 Ω maximum matching between switches help limit channel-dependent error. At the board level, keep the common and switched nodes away from switching control traces, and verify settling time against the highest signal bandwidth used by the fixture.
מומלץ
Data-Acquisition Multiplexing
DG405DJ+ can route analog inputs in a data-acquisition front end where each channel must connect to a common amplifier or converter. The two 2:1 sections support channel selection without mechanical relays, and the guaranteed 3 Ω maximum on-resistance flatness helps maintain predictable behavior across the signal range. When driving a high-impedance input, include amplifier input capacitance and PCB parasitic capacitance in settling calculations. Confirm leakage and off-state isolation requirements in the datasheet before reusing the same switch between adjacent high-impedance sources.
מומלץ
Communications Signal Isolation
The DG405DJ+ is appropriate for switching balanced or single-ended communication paths where two 2:1 channels provide convenient source selection. Its 45 Ω maximum on-resistance can support many moderate-impedance signal paths, while the 20 Ω typical value reduces insertion loss in typical designs. The normally open configuration keeps the common node disconnected during the inactive state. Validate bandwidth, insertion loss, return loss, and channel isolation at the intended operating frequency rather than relying only on the DC on-resistance rating.
מומלץ
Audio Signal Switching
DG405DJ+ can select between two audio paths while preserving a compact, dual-channel implementation. The 20 Ω typical on-resistance is practical for many audio inputs when the downstream amplifier presents an appropriate load, and the guaranteed channel matching of 2 Ω maximum reduces gain imbalance between switches. Use the datasheet’s distortion, off-state isolation, and bandwidth characteristics to confirm suitability for the selected signal level and impedance. Place the IC near the routed nodes to minimize added board capacitance and crosstalk.
מומלץ
Industrial Control Signal Routing
The DG405DJ+ can route control or sensor signals in industrial electronics where solid-state switching and independent dual-channel control are beneficial. Its CMOS implementation supports low power use, while the PDIP package remains convenient for through-hole industrial assemblies and maintenance-friendly prototypes. Designers should verify supply-voltage limits and control thresholds against the industrial system rails, then provide bypassing close to the device. Also evaluate off-state leakage when switching sensor outputs whose impedance may be much higher than the test load.
מומלץ
Sample-and-Hold Interface
DG405DJ+ can form part of a sample-and-hold interface by connecting one of two sources to a holding or measurement node. The two independently controlled 2:1 channels allow the system to manage more than one routing function within a single package. On-resistance flatness of 3 Ω maximum provides useful control over signal-dependent resistance variation, while switching transients remain important at high source impedances. Use the manufacturer timing and charge-injection data to establish acquisition timing, and add the sampling capacitor’s leakage and dielectric behavior to the error budget.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DG405DJ+ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DG405DJ | DG405DJ-E3 |
|---|---|---|---|
| Brand | Analog Devices | Vishay Intertechnology | Vishay Intertechnology |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | 2:1 per channel | 2:1 per channel | 2:1 per channel |
| Maximum On-Resistance | 45 ohm | 45 ohm | 45 ohm |
| Typical On-Resistance | 20 ohm | 20 ohm | 20 ohm |
| On-Resistance Matching Between Switches | 2 ohm maximum | 2 ohm maximum | 2 ohm maximum |
| On-Resistance Flatness Over Signal Range | 3 ohm maximum | 3 ohm maximum | 3 ohm maximum |
| Switch Type | Normally open | Normally open | Normally open |
| Technology | CMOS | CMOS | CMOS |
מבדילים עיקריים
- Guaranteed channel-to-channel on-resistance matching (לעומתDG405DJ-E3)
- Defined on-resistance flatness across the signal range (לעומתDG405DJ)
- Dual 2:1 architecture in a through-hole package (לעומתDG405DJ-E3)
הערות תכנון
Treat the DG405DJ+ as a resistance with parasitic capacitance rather than as an ideal conductor. Its 20 Ω typical and 45 Ω maximum on-resistance can create measurable division with source and load impedances, while the 3 Ω maximum flatness specification limits signal-dependent resistance variation. Keep traces short, terminate them according to the system impedance, and verify settling at the highest input frequency. Place sensitive nodes away from control traces to reduce capacitive coupling during switching.
Route the two switched paths and common nodes directly to their intended destinations, avoiding shared narrow segments between switch pins. Keep the 16-pin PDIP footprint consistent with the package drawing and pin numbering, and maintain adequate spacing between high-impedance signal traces and adjacent control or supply conductors. If the analog source impedance is high, minimize parasitic capacitance by keeping the IC and routed nodes away from connectors, regulators, and digital timing circuits.
Do not select the switch from DC on-resistance alone. Confirm bandwidth, off-state isolation, leakage, charge injection, switching time, supply voltage, and control thresholds in the DG405 datasheet. The normally open configuration is also not interchangeable with a normally closed or break-before-make arrangement without a logic review. For replacement parts, compare every terminal function and control polarity instead of assuming that identical PDIP pin counts guarantee compatibility.
Use the manufacturer-specified bypass capacitors and place them close to the supply and ground pins. Keep return-current paths short so switching activity does not inject additional disturbance into sensitive analog circuitry. Estimate the device dissipation from the actual supply voltage and control state, then verify that the operating temperature and leakage limits remain acceptable. For battery-powered or portable designs, account for both active-state current and leakage when evaluating the overall power budget.
מידע על תאימות
The component listing identifies DG405DJ+ as RoHS compliant and lead free. AEC-Q100 is not applicable to this general-purpose analog switch.