Texas Instruments

DS90LV011AHMFX - 400 Mbps LVDS Driver | Texas Instruments

MPN: DS90LV011AHMFX ✓ פעיל
3 V Vdss Minimized by current-mode output architecture Id SOT-23-5, 5 pins Package Low EMI with typical 350 mV output swing Memory
כמות הזמנה מינימלית: 1 |

DS90LV011AHMFX סקירה

Texas Instruments DS90LV011AHMFX is a 3 V single-channel LVDS differential driver designed for data rates in excess of 400 Mbps (200 MHz), housed in a 5-pin SOT-23 package. It uses a current-mode output architecture to maintain low power dissipation at high frequency while minimizing short-circuit fault current.

An LVDS differential driver is a low-voltage differential-signaling interface IC that converts a single-ended logic signal into a low-voltage differential pair. The DS90LV011AHMFX belongs to the LVDS driver hierarchy within interface ICs and provides the transmitting side of a high-speed differential link. Its typical 350 mV output swing reduces signal amplitude while preserving noise immunity and low electromagnetic interference.

The primary features of the DS90LV011AHMFX include support for more than 400 Mbps data rates, a current-mode LVDS output, low high-frequency power dissipation, minimized short-circuit fault current, and a 3 V supply. The high-temperature variant supports operation from -40°C to +125°C, making it suitable for industrial and extended-temperature equipment where ordinary commercial-temperature interface ICs may be unsuitable.

The differential output arrangement supports compact PCB routing and controlled impedance. Because the driver produces complementary Y and Z outputs, the receiving circuit must interpret differential voltage rather than the logic state of either output independently. The typical 350 mV output swing also helps limit conducted and radiated emissions compared with a larger single-ended transition, provided that the PCB implements the recommended controlled-impedance differential pair.

Typical applications include high-speed point-to-point LVDS links, industrial control and test systems, video and display interfaces, communications equipment, and data-acquisition systems. The device can be paired with the DS90LT012AH single line receiver or with compatible Texas Instruments LVDS receivers. It is particularly useful where the link rate exceeds 400 Mbps but system power and board area must remain low.

PCB implementation should use a short, symmetrical differential trace pair with continuous reference planes and matched termination at the receiver. Keep the LVDS pair away from noisy switching nodes and maintain consistent spacing between the two traces. Decoupling capacitance should be placed close to the supply pin, while the ground connection must return directly to the device ground without interruption through high-current paths.

This product page combines manufacturer specifications, sourcing guidance, drop-in alternatives, application analysis, and practical PCB implementation notes to support faster component evaluation and board-level design.

חלופות תחליף ישיר עבור DS90LV011AHMFX — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

DS90LV011AHMF/NOPB

✅ Drop-In
📦 SOT-23-5
Same 400 Mbps data-rate class and 3 V supply class in the same 5-pin footprint; the /NOPB code identifies the lead-free finish rather than the tape-and-reel configuration.

📋 חלופה להתייחסות (לא בקטלוג)

DS90LV011AQMFX/NOPB

✅ Drop-In
📦 SOT-23-5
Same 400 Mbps and 3 V device class in a 5-pin SOT-23 footprint; the AQM suffix represents a different ordering and temperature-grade variant.

📋 חלופה להתייחסות (לא בקטלוג)

DS90LV011AQMF/NOPB

✅ Drop-In
📦 SOT-23-5
Same 400 Mbps and 3 V device class in a 5-pin SOT-23 footprint; the AQM ordering family differs by approximately 10% in the compatibility rating.

📋 חלופה להתייחסות (לא בקטלוג)

DS90LV011AQMFE/NOPB

✅ Drop-In
📦 SOT-23-5
Same 400 Mbps and 3 V device class in a 5-pin SOT-23 footprint; the AQM ordering family differs by approximately 10% in the compatibility rating.

📋 חלופה להתייחסות (לא בקטלוג)

DS90LV011ATMF/NOPB

✅ Drop-In
📦 SOT-23-5
Same 400 Mbps data-rate class, 3 V supply class, and 5-pin footprint; the AT versus AH temperature-grade characteristics produce an approximately 10% compatibility difference.

📋 חלופה להתייחסות (לא בקטלוג)

DS90LV011AHMFX מפרטים

Product Type Single-channel LVDS differential driver
מתח אספקה 3 V
Maximum Data Rate >400 Mbps (200 MHz)
Output Architecture Current-mode differential output
Typical Differential Output Swing 350 mV
טווח טמפרטורת פעולה -40°C to +125°C
Short-Circuit Fault Current Minimized by current-mode output architecture
Power Dissipation Low at high frequency
Number of Channels 1 channel
תצורת מוצא Differential Y/Z outputs
Signaling Standard Low Voltage Differential Signaling (LVDS)
מארז SOT-23-5, 5 pins
סוג הרכבה Surface mount
Electromagnetic Interference Low EMI with typical 350 mV output swing
PCB Layout LVDS outputs arranged for easy PCB layout

תצורת פינים של DS90LV011AHMFX

SOT-23-5 Package Pinout Diagram SOT-23-5 5-pin surface mount IC, JEDEC MO-178. Pin 1 by dot. 1 2 3 4 5 SOT-23-5
פין 1 VCC — 3 V power supply connection
פין 2 GND — Ground connection
פין 3 A — Single-ended data input
פין 4 Y — Noninverted differential output
פין 5 Z — Inverted differential output

יישומים טיפוסיים

DS90LV011AHMFX מתאים עבור 6 יישוםs: High-Speed Point-to-Point LVDS Link, Industrial Control and Automation, Video and Display Data Transport, Test and Measurement Systems, Communications Equipment, Data Acquisition and Sensor Interfaces.

🌐

High-Speed Point-to-Point LVDS Link

The DS90LV011AHMFX fits point-to-point links that require one differential channel at more than 400 Mbps, equivalent to over 200 MHz. Its current-mode architecture limits power dissipation as data frequency increases and minimizes short-circuit fault current, making it more suitable for sustained high-rate operation than a simple voltage-mode output. The complementary Y and Z outputs should be routed as a matched differential pair to a compatible receiver, with receiver-side termination selected from the channel design. The driver’s typical 350 mV output swing supports a compact, low-EMI interface while preserving sufficient differential signal amplitude for reliable detection.

🏭

Industrial Control and Automation

Industrial controllers often distribute high-speed timing, control, or sensor data across several circuit boards. The DS90LV011AHMFX supports rates above 400 Mbps while operating across -40°C to +125°C, matching applications with extended environmental requirements. Its current-mode output controls dissipation at elevated data rates, and the typical 350 mV differential swing reduces signal amplitude and EMI on factory-floor equipment. Use short, impedance-controlled traces between the transmitter and receiver, maintain a continuous ground reference, and isolate the differential pair from motor, relay, and switching-power paths.

📺

Video and Display Data Transport

The DS90LV011AHMFX can transmit a high-speed differential video or control lane when the link’s pixel rate, timing budget, and receiver architecture align with its greater-than-400-Mbps capability. The 350 mV typical LVDS swing helps limit electromagnetic emissions, while the current-mode output keeps dissipation low at high activity rates. A compact 5-pin SOT-23 package also saves board area compared with larger multi-channel transceivers. Validate the complete source-to-sink channel, including connector or cable loss, receiver thresholds, and the differential trace geometry, before treating a general-purpose LVDS driver as a display-standard-compliant solution.

🔧

Test and Measurement Systems

Precision test equipment can use the DS90LV011AHMFX to move synchronized measurements, trigger signals, or command data between modules over a compact differential link. Supporting more than 400 Mbps provides headroom for high-throughput acquisition systems while the small SOT-23-5 package simplifies dense front-panel and instrument-board layouts. The low typical 350 mV swing reduces coupling into sensitive analog sections, and the -40°C to +125°C range supports extended-temperature equipment. Keep the differential route away from clock and power-converter nodes, and use a receiver with input thresholds appropriate for the intended cable or PCB distance.

🌐

Communications Equipment

The DS90LV011AHMFX is appropriate for low-power backplane, rack, or module-to-module communication links operating above 400 Mbps. Its current-mode architecture reduces power dissipation at high frequency, and minimized short-circuit current improves robustness if an output is exposed to a fault condition. Differential Y and Z routing lowers EMI susceptibility and emission when implemented with continuous impedance control. For communications equipment, place local decoupling at the 3 V supply pin, maintain equal routing to the receiver, and apply the termination specified by the complete link rather than adding resistance indiscriminately to individual outputs.

🧩

Data Acquisition and Sensor Interfaces

The DS90LV011AHMFX can carry synchronized acquisition data from a sensor or analog front end to a processing section when the required transfer rate exceeds 400 Mbps. Differential signaling reduces sensitivity to common-mode noise compared with a single-ended link, while the low 350 mV output swing helps preserve measurement-system signal integrity. The compact 5-pin package leaves more board area for analog components, and current-mode operation keeps high-frequency dissipation controlled. Route the pair away from ADC clocks and switching regulators, verify the receiver’s input bandwidth and threshold, and include connector or cable losses in the channel budget.

סיכום מוצרים מומלצים

DS90LT012AH Companion single-line LVDS receiver בשימוש ב-: High-Speed Point-to-Point LVDS Link, Industrial Control and Automation, Video and Display Data Transport, Test and Measurement Systems, Communications Equipment, Data Acquisition and Sensor Interfaces
What is the operating voltage of DS90LV011AHMFX?
The DS90LV011AHMFX operates from a 3 V supply. According to the Texas Instruments DS90LV011AH datasheet, the device is a current-mode LVDS differential driver designed for low-voltage, high-speed interface systems. Its typical differential output swing is 350 mV, while its current-mode architecture keeps power dissipation and short-circuit fault current controlled as operating frequency rises.
What is the maximum data rate of DS90LV011AHMFX?
The DS90LV011AHMFX supports data rates in excess of 400 Mbps, equivalent to more than 200 MHz. According to the Texas Instruments DS90LV011AH datasheet, this performance is achieved with a current-mode output architecture that reduces power dissipation at high frequency and minimizes short-circuit fault current. The device is therefore appropriate for compact, high-speed differential signaling links.
Where can I download the DS90LV011AHMFX datasheet PDF?
The official DS90LV011AHMFX datasheet is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90lv011ah.pdf. The document describes the 3 V LVDS differential driver, its current-mode output, operation above 400 Mbps, 5-pin SOT-23 package, 350 mV typical output swing, electrical characteristics, and recommended implementation details.
Where can I find the DS90LV011AHMFX pinout?
The DS90LV011AHMFX pin configuration is shown in the pin-description section of the official Texas Instruments DS90LV011AH datasheet. The device uses a 5-pin SOT-23 package containing the supply, ground, input, and differential output connections. Assign PCB tracks from the datasheet pin-description table rather than relying only on the physical package orientation.
Is DS90LV011AHMFX suitable for industrial temperature environments?
Yes, the DS90LV011AHMFX is specified for a -40°C to +125°C operating-temperature range. According to the manufacturer product information, this high-temperature 3 V LVDS differential driver is intended for demanding interface applications. The range supports industrial, communications, and test equipment where operation outside the standard commercial-temperature interval is required.
What can replace the DS90LV011AHMFX?
The DS90LV011AHMF/NOPB and DS90LV011AQMFX/NOPB are pin-compatible 5-pin SOT-23 LVDS-driver alternatives to the DS90LV011AHMFX. The DS90LV011AHMF/NOPB retains the stated 400 Mbps class and 3 V operating class in the same package. Confirm temperature grade, supply limits, enable or shutdown behavior, and receiver compatibility before approving a substitution.
What is the best drop-in replacement for DS90LV011AHMFX?
The DS90LV011AHMF/NOPB is the closest listed drop-in choice because it uses the same 5-pin SOT-23 footprint and remains in the same 400 Mbps, 3 V LVDS-driver family. The DS90LV011AQMFX/NOPB is another package-compatible family option. Treat exact qualification and operating-temperature requirements as part of the final substitution review rather than relying on package similarity alone.
DS90LV011AHMFX vs DS90LV011ATMF/NOPB — which is better?
The DS90LV011AHMFX is the better choice when the design specifically requires the AH high-temperature ordering variant. The DS90LV011ATMF/NOPB is also a 5-pin SOT-23 LVDS driver, but the AT and AH variants have different electrical or temperature-grade characteristics. Review the manufacturer datasheets for the exact operating limits before using the AT version in an AH-qualified design.
Is DS90LV011AHMFX the same as DS90LV011AHMF/NOPB?
The DS90LV011AHMFX and DS90LV011AHMF/NOPB are functionally equivalent 5-pin SOT-23 LVDS-driver versions from Texas Instruments. The MFX ordering code specifies the tape-and-reel shipping configuration, while /NOPB identifies the lead-free finish option. Both remain in the same 400 Mbps, 3 V device family, but procurement and assembly documentation must use the exact ordered suffix.
When should I choose DS90LV011AHMFX over another LVDS driver?
Choose DS90LV011AHMFX when a design needs one 3 V LVDS differential output, operation above 400 Mbps, low high-frequency power dissipation, and an extended -40°C to +125°C temperature range. It is also appropriate when the board must use a compact 5-pin SOT-23 footprint and when the receiver can support the driver’s differential Y/Z output arrangement.
Is DS90LV011AHMFX suitable for a video interface?
The DS90LV011AHMFX can suit video or display links when the required lane rate, receiver interface, and timing budget match its greater-than-400-Mbps capability. Its differential output and typical 350 mV swing reduce EMI and support controlled-impedance routing. The source, sink, and cable or PCB channel must nevertheless be validated together for video-specific timing and signaling requirements.
How should DS90LV011AHMFX be laid out for low EMI?
Route the differential Y and Z outputs as a short, symmetrical pair over a continuous reference plane and use the termination specified by the receiver and channel design. Keep the pair away from switching power nodes and other high-current paths. Place local supply decoupling close to the supply pin and connect the device ground directly to the ground plane without routing return current through the differential pair.
Where can I buy DS90LV011AHMFX and check its lead time?
Use the Request a Quote form on this page to request the current price, stock position, lead time, and minimum order quantity for DS90LV011AHMFX. The exact suffix identifies the tape-and-reel configuration, so include the complete MPN when requesting a quotation. This avoids ambiguity with the /NOPB ordering option or other package-ordering codes.
How much does DS90LV011AHMFX cost?
The current commercial price for DS90LV011AHMFX is best obtained through the Request a Quote form on this page. The form returns pricing against the exact MPN, quantity, and required shipment configuration. Pricing can change with quantity, availability, and market conditions, so a request quote is more reliable than treating a historical catalog figure as current.
Is DS90LV011AHMFX in stock?
Current inventory for DS90LV011AHMFX should be confirmed through the Request a Quote form on this page. Provide the required quantity and the tape-and-reel shipping configuration identified by the complete MPN. The confirmation can also cover factory lead time, partial shipment availability, and any minimum-order constraints for the exact ordering code.
What are the key specifications of DS90LV011AHMFX that engineers should know?
The DS90LV011AHMFX is a single-channel, 3 V, current-mode LVDS differential driver in a 5-pin SOT-23 package. It supports data rates above 400 Mbps (200 MHz), has a typical 350 mV differential output swing, and operates from -40°C to +125°C. Its low high-frequency dissipation and minimized short-circuit current are the principal technical benefits for high-speed links.

נתוני עזר הנדסיים עבור DS90LV011AHMFX — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the DS90LV011AHMFX when the PCB requires a single 3 V LVDS differential channel capable of more than 400 Mbps, low high-frequency power dissipation, and operation across -40°C to +125°C. Its 5-pin SOT-23 package and 350 mV typical differential swing suit compact, low-EMI point-to-point designs. Select DS90LV011AHMF/NOPB when the same electrical family and footprint are needed but a lead-free /NOPB ordering code is preferred. Consider DS90LV011AQMFX/NOPB, DS90LV011AQMF/NOPB, or DS90LV011AQMFE/NOPB only after checking the exact temperature grade, supply range, and ordering requirements. DS90LV011ATMF/NOPB is appropriate when its AT-specific characteristics meet the system limits, but it should not replace an AH-qualified design without review. In every case, verify differential pinout, receiver thresholds, termination, channel loss, and the manufacturer datasheet before releasing a drop-in substitution.

השוואה עם חלופות

פרמטר מוצר זה DS90LV011AHMF/NOPB DS90LV011AQMFX/NOPB DS90LV011AQMF/NOPB DS90LV011AQMFE/NOPB DS90LV011ATMF/NOPB
Package SOT-23-5 SOT-23-5 SOT-23-5 SOT-23-5 SOT-23-5 SOT-23-5
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Product Type Single-channel LVDS differential driver LVDS driver LVDS driver LVDS driver LVDS driver LVDS driver
Maximum Data Rate >400 Mbps (200 MHz) 400 Mbps 400 Mbps 400 Mbps 400 Mbps 400 Mbps
Supply Voltage 3 V 3 V 3 V 3 V 3 V 3 V
Number of Channels 1 1 1 1 1 1
Differential Outputs Y and Z outputs Y and Z outputs Y and Z outputs Y and Z outputs Y and Z outputs Y and Z outputs

מבדילים עיקריים

  • Supports high-rate LVDS operation in a compact package (לעומתDS90LV011AHMF/NOPB)
  • Extended-temperature AH variant (לעומתDS90LV011ATMF/NOPB)
  • Low high-frequency dissipation architecture (לעומתDS90LV011AQMFX/NOPB)
  • Low-amplitude differential output (לעומתDS90LV011AQMF/NOPB)

הערות תכנון

Route Y and Z as a short, symmetric differential pair over a continuous reference plane. Keep the traces equally spaced, avoid plane splits and test-point discontinuities, and match the receiver termination to the complete transmission channel. The 350 mV differential swing supports low EMI only when the physical pair is controlled; widely separated or asymmetric traces can substantially degrade common-mode rejection.

Place the local supply-decoupling capacitor immediately beside the VCC and GND connections, with a short and low-inductance ground return. Keep the LVDS pair away from switching-regulator traces, clock outputs, relay contacts, and high-current return paths. Preserve the differential geometry through connector transitions and avoid adding stubs or test pads that create unwanted reflections.

Do not interpret the Y and Z outputs as independent logic signals; they form one differential channel and must be received differentially. Also do not assume that any 5-pin SOT-23 LVDS driver is interchangeable solely because its footprint matches. Confirm the exact ordering suffix, supply limits, data-rate rating, temperature grade, output polarity, and receiver compatibility before approving a substitution.

The DS90LV011AHMFX supports data rates above 400 Mbps, so loss from PCB traces, connectors, and cables must be included in the channel budget. Use a compatible high-speed LVDS receiver and observe its recommended termination arrangement. When the link includes a cable or connector, characterize reflections and differential attenuation across temperature; a low output swing alone does not guarantee reliable operation over every physical channel.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

Compliance attributes are unknown because the manufacturer product information does not explicitly state the required statuses for the exact ordering code.

חיפושים קשורים

DS90LV011AHMFX DS90LV011AHMFX datasheet DS90LV011AHMFX datasheet pdf DS90LV011AHMFX pinout DS90LV011AHMFX equivalent DS90LV011AHMFX replacement DS90LV011AHMFX price DS90LV011AHMFX stock DS90LV011AHMFX SOT-23-5 DS90LV011AHMFX LVDS driver DS90LV011AHMFX 400 Mbps DS90LV011AHMFX vs DS90LV011ATMF/NOPB Texas Instruments DS90LV011AHMFX DS90LV011AHMFX high temperature driver SOT-23-5 LVDS driver pinout

רכיבים ומונחים קשורים

Texas Instruments DS90LV011AHMFX DS90LV011AH DS90LV011AHMF/NOPB DS90LV011AQMFX/NOPB DS90LV011AQMF/NOPB DS90LV011AQMFE/NOPB DS90LV011ATMF/NOPB DS90LT012AH LVDS driver LVDS differential line driver interface IC current-mode output SOT-23-5 SOT-23 package family surface-mount technology Low Voltage Differential Signaling differential output Y and Z outputs 350 mV output swing 400 Mbps data rate electromagnetic interference controlled-impedance routing
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר