DS90LV011AHMFX - 400 Mbps LVDS Driver | Texas Instruments
MPN: DS90LV011AHMFX ✓ ActiveDS90LV011AHMFX Overview
An LVDS differential driver is a low-voltage differential-signaling interface IC that converts a single-ended logic signal into a low-voltage differential pair. The DS90LV011AHMFX belongs to the LVDS driver hierarchy within interface ICs and provides the transmitting side of a high-speed differential link. Its typical 350 mV output swing reduces signal amplitude while preserving noise immunity and low electromagnetic interference.
The primary features of the DS90LV011AHMFX include support for more than 400 Mbps data rates, a current-mode LVDS output, low high-frequency power dissipation, minimized short-circuit fault current, and a 3 V supply. The high-temperature variant supports operation from -40°C to +125°C, making it suitable for industrial and extended-temperature equipment where ordinary commercial-temperature interface ICs may be unsuitable.
The differential output arrangement supports compact PCB routing and controlled impedance. Because the driver produces complementary Y and Z outputs, the receiving circuit must interpret differential voltage rather than the logic state of either output independently. The typical 350 mV output swing also helps limit conducted and radiated emissions compared with a larger single-ended transition, provided that the PCB implements the recommended controlled-impedance differential pair.
Typical applications include high-speed point-to-point LVDS links, industrial control and test systems, video and display interfaces, communications equipment, and data-acquisition systems. The device can be paired with the DS90LT012AH single line receiver or with compatible Texas Instruments LVDS receivers. It is particularly useful where the link rate exceeds 400 Mbps but system power and board area must remain low.
PCB implementation should use a short, symmetrical differential trace pair with continuous reference planes and matched termination at the receiver. Keep the LVDS pair away from noisy switching nodes and maintain consistent spacing between the two traces. Decoupling capacitance should be placed close to the supply pin, while the ground connection must return directly to the device ground without interruption through high-current paths.
This product page combines manufacturer specifications, sourcing guidance, drop-in alternatives, application analysis, and practical PCB implementation notes to support faster component evaluation and board-level design.
Drop-in alternatives for DS90LV011AHMFX — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
DS90LV011AHMF/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV011AQMFX/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV011AQMF/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV011AQMFE/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV011ATMF/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV011AHMFX Specifications
| Product Type | Single-channel LVDS differential driver |
| Supply Voltage | 3 V |
| Maximum Data Rate | >400 Mbps (200 MHz) |
| Output Architecture | Current-mode differential output |
| Typical Differential Output Swing | 350 mV |
| Operating Temperature Range | -40°C to +125°C |
| Short-Circuit Fault Current | Minimized by current-mode output architecture |
| Power Dissipation | Low at high frequency |
| Number of Channels | 1 channel |
| Output Configuration | Differential Y/Z outputs |
| Signaling Standard | Low Voltage Differential Signaling (LVDS) |
| Package | SOT-23-5, 5 pins |
| Mounting Type | Surface mount |
| Electromagnetic Interference | Low EMI with typical 350 mV output swing |
| PCB Layout | LVDS outputs arranged for easy PCB layout |
DS90LV011AHMFX Pin Configuration
| Pin 1 | VCC — 3 V power supply connection |
| Pin 2 | GND — Ground connection |
| Pin 3 | A — Single-ended data input |
| Pin 4 | Y — Noninverted differential output |
| Pin 5 | Z — Inverted differential output |
Typical Applications
DS90LV011AHMFX is suitable for 6 applications: High-Speed Point-to-Point LVDS Link, Industrial Control and Automation, Video and Display Data Transport, Test and Measurement Systems, Communications Equipment, Data Acquisition and Sensor Interfaces.
High-Speed Point-to-Point LVDS Link
The DS90LV011AHMFX fits point-to-point links that require one differential channel at more than 400 Mbps, equivalent to over 200 MHz. Its current-mode architecture limits power dissipation as data frequency increases and minimizes short-circuit fault current, making it more suitable for sustained high-rate operation than a simple voltage-mode output. The complementary Y and Z outputs should be routed as a matched differential pair to a compatible receiver, with receiver-side termination selected from the channel design. The driver’s typical 350 mV output swing supports a compact, low-EMI interface while preserving sufficient differential signal amplitude for reliable detection.
Recommended
Industrial Control and Automation
Industrial controllers often distribute high-speed timing, control, or sensor data across several circuit boards. The DS90LV011AHMFX supports rates above 400 Mbps while operating across -40°C to +125°C, matching applications with extended environmental requirements. Its current-mode output controls dissipation at elevated data rates, and the typical 350 mV differential swing reduces signal amplitude and EMI on factory-floor equipment. Use short, impedance-controlled traces between the transmitter and receiver, maintain a continuous ground reference, and isolate the differential pair from motor, relay, and switching-power paths.
Recommended
Video and Display Data Transport
The DS90LV011AHMFX can transmit a high-speed differential video or control lane when the link’s pixel rate, timing budget, and receiver architecture align with its greater-than-400-Mbps capability. The 350 mV typical LVDS swing helps limit electromagnetic emissions, while the current-mode output keeps dissipation low at high activity rates. A compact 5-pin SOT-23 package also saves board area compared with larger multi-channel transceivers. Validate the complete source-to-sink channel, including connector or cable loss, receiver thresholds, and the differential trace geometry, before treating a general-purpose LVDS driver as a display-standard-compliant solution.
Recommended
Test and Measurement Systems
Precision test equipment can use the DS90LV011AHMFX to move synchronized measurements, trigger signals, or command data between modules over a compact differential link. Supporting more than 400 Mbps provides headroom for high-throughput acquisition systems while the small SOT-23-5 package simplifies dense front-panel and instrument-board layouts. The low typical 350 mV swing reduces coupling into sensitive analog sections, and the -40°C to +125°C range supports extended-temperature equipment. Keep the differential route away from clock and power-converter nodes, and use a receiver with input thresholds appropriate for the intended cable or PCB distance.
Recommended
Communications Equipment
The DS90LV011AHMFX is appropriate for low-power backplane, rack, or module-to-module communication links operating above 400 Mbps. Its current-mode architecture reduces power dissipation at high frequency, and minimized short-circuit current improves robustness if an output is exposed to a fault condition. Differential Y and Z routing lowers EMI susceptibility and emission when implemented with continuous impedance control. For communications equipment, place local decoupling at the 3 V supply pin, maintain equal routing to the receiver, and apply the termination specified by the complete link rather than adding resistance indiscriminately to individual outputs.
Recommended
Data Acquisition and Sensor Interfaces
The DS90LV011AHMFX can carry synchronized acquisition data from a sensor or analog front end to a processing section when the required transfer rate exceeds 400 Mbps. Differential signaling reduces sensitivity to common-mode noise compared with a single-ended link, while the low 350 mV output swing helps preserve measurement-system signal integrity. The compact 5-pin package leaves more board area for analog components, and current-mode operation keeps high-frequency dissipation controlled. Route the pair away from ADC clocks and switching regulators, verify the receiver’s input bandwidth and threshold, and include connector or cable losses in the channel budget.
Recommended
Recommended Products Summary
Engineering reference data for DS90LV011AHMFX — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | DS90LV011AHMF/NOPB | DS90LV011AQMFX/NOPB | DS90LV011AQMF/NOPB | DS90LV011AQMFE/NOPB | DS90LV011ATMF/NOPB |
|---|---|---|---|---|---|---|
| Package | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Single-channel LVDS differential driver | LVDS driver | LVDS driver | LVDS driver | LVDS driver | LVDS driver |
| Maximum Data Rate | >400 Mbps (200 MHz) | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps |
| Supply Voltage | 3 V | 3 V | 3 V | 3 V | 3 V | 3 V |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Differential Outputs | Y and Z outputs | Y and Z outputs | Y and Z outputs | Y and Z outputs | Y and Z outputs | Y and Z outputs |
Key Differentiators
- Supports high-rate LVDS operation in a compact package (vs DS90LV011AHMF/NOPB)
- Extended-temperature AH variant (vs DS90LV011ATMF/NOPB)
- Low high-frequency dissipation architecture (vs DS90LV011AQMFX/NOPB)
- Low-amplitude differential output (vs DS90LV011AQMF/NOPB)
Design Notes
Route Y and Z as a short, symmetric differential pair over a continuous reference plane. Keep the traces equally spaced, avoid plane splits and test-point discontinuities, and match the receiver termination to the complete transmission channel. The 350 mV differential swing supports low EMI only when the physical pair is controlled; widely separated or asymmetric traces can substantially degrade common-mode rejection.
Place the local supply-decoupling capacitor immediately beside the VCC and GND connections, with a short and low-inductance ground return. Keep the LVDS pair away from switching-regulator traces, clock outputs, relay contacts, and high-current return paths. Preserve the differential geometry through connector transitions and avoid adding stubs or test pads that create unwanted reflections.
Do not interpret the Y and Z outputs as independent logic signals; they form one differential channel and must be received differentially. Also do not assume that any 5-pin SOT-23 LVDS driver is interchangeable solely because its footprint matches. Confirm the exact ordering suffix, supply limits, data-rate rating, temperature grade, output polarity, and receiver compatibility before approving a substitution.
The DS90LV011AHMFX supports data rates above 400 Mbps, so loss from PCB traces, connectors, and cables must be included in the channel budget. Use a compatible high-speed LVDS receiver and observe its recommended termination arrangement. When the link includes a cable or connector, characterize reflections and differential attenuation across temperature; a low output swing alone does not guarantee reliable operation over every physical channel.
Compliance Information
Compliance attributes are unknown because the manufacturer product information does not explicitly state the required statuses for the exact ordering code.