DSPIC30F6013A-30I/PT - 30 MIPS 16-Bit DSC, 132KB Flash | Microchip
MPN: DSPIC30F6013A-30I/PT ✓ פעילDSPIC30F6013A-30I/PT סקירה
A Digital Signal Controller (DSC) is a hybrid device that fuses a microcontroller's deterministic control peripherals with a Digital Signal Processor (DSP) engine capable of single-cycle MAC operations. The DSC category sits within the broader taxonomy of microcontrollers -> embedded controllers -> MCUs with DSP extensions, and is optimized for applications that require both closed-loop control (PWM, ADC) and high-speed numerical processing (FFT, FIR, encoder feedback) on a single chip.
Key features include 132 KB of Flash program memory (44K x 24 organization), 30 MIPS execution from a 120 MHz internal clock, dual 40-bit accumulators, zero-overhead hardware DO and REPEAT loops, and 16 x 16-bit signed fractional multiplication in a single cycle. The 80-pin TQFP exposes up to 68 I/O lines, two UART modules, two SPI modules, two I2C modules, two CAN modules, an 8-channel motor-control PWM, a 16-channel 10-bit ADC, and a 12-bit ADC converter for high-resolution analog front-ends.
Architecturally, the DSPIC30F6013A combines a 16-bit native datapath with DSP-engine MAC units and a barrel shifter, allowing efficient implementation of digital filters, motor-control algorithms (field-oriented control, space-vector modulation), and power-conversion control loops. The wide operating range of 4.5 V to 5.5 V (5 V nominal) and -40C to +85C industrial temperature grade make it suitable for harsh environments.
Typical applications include three-phase AC induction and BLDC motor drives, switch-mode power supplies (SMPS), digital UPS systems, automotive body controllers, industrial automation and PLCs, and audio processing. The 132 KB code space and 30 MIPS throughput cover full-featured sensorless FOC and PFC firmware in a single device.
A key design consideration is that the 5 V supply rail must be tightly decoupled with bulk + bypass capacitors, since ADC accuracy and PWM timing margins are sensitive to VDD ripple. Code protection fuse settings should be configured last in production to prevent bricking prototypes during development.
חלופות תחליף ישיר עבור DSPIC30F6013A-30I/PT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DSPIC30F6013A-30I/PT (אותו גורם צורה וטביעת רגל) — שונים ב Package, ADC, Core Architecture, Operating Temperature, Timers.
DSPIC30F6014A-30I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6012A-30I/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6013A-20I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6013AT-30I/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6011A-30I/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6013A-30I/PT דירוגים מרביים ומאפיינים חשמליים
| Product Type | 16-bit Digital Signal Controller (DSC) |
| Architecture | Modified Harvard RISC with DSP engine |
| Program Memory | 132 KB Flash |
| RAM | 4 KB SRAM |
| Data EEPROM | 8 KB |
| Instruction Throughput | 30 MIPS |
| CPU Clock (max) | 120 MHz internal (30 MIPS from 4x PLL) |
| מתח אספקה | 4.5 V to 5.5 V |
| I/O Pins | 68 |
| מארז | 80-pin TQFP (12x12 mm) |
| טמפרטורת פעולה | -40C to +85C (Industrial) |
| ADC | 12-bit SAR, up to 16 channels |
| Motor Control PWM | 8-channel, dedicated PWM module |
| Communication Interfaces | 2x UART, 2x SPI, 2x I2C, 2x CAN |
| Timers | 5x 16-bit timers |
| סוג הרכבה | Surface Mount |
| רמת MSL | 3 |
| סטטוס RoHS | Compliant (lead-free) |
תצורת פינים של DSPIC30F6013A-30I/PT
| פין 1 | AN0 — Analog input 0 / VREF+ |
| פין 2 | AN1 — Analog input 1 |
| פין 3 | AN2 — Analog input 2 |
| פין 4 | AN3 — Analog input 3 |
| פין 5 | AN4 — Analog input 4 |
| פין 6 | AN5 — Analog input 5 |
| פין 7 | AN6 — Analog input 6 |
| פין 8 | AN7 — Analog input 7 |
| פין 9 | AN8 — Analog input 8 |
| פין 10 | AN9 — Analog input 9 |
| פין 11 | AN10 — Analog input 10 |
| פין 12 | AN11 — Analog input 11 |
| פין 13 | AN12 — Analog input 12 |
| פין 14 | AN13 — Analog input 13 |
| פין 15 | AN14 — Analog input 14 |
| פין 16 | AN15 — Analog input 15 |
| פין 17 | AVSS — Analog ground |
| פין 18 | AVDD — Analog supply |
| פין 19 | MCLR — Master clear / reset (active low) |
| פין 20 | OSC1 — Crystal oscillator input |
| פין 21 | OSC2 — Crystal oscillator output |
| פין 22 | VDD — Digital supply |
| פין 23 | VSS — Digital ground |
| פין 24 | PGEC1 — ICSP programming clock 1 |
| פין 25 | PGED1 — ICSP programming data 1 |
| פין 26 | PWM1L — PWM1 low-side output |
| פין 27 | PWM1H — PWM1 high-side output |
| פין 28 | PWM2L — PWM2 low-side output |
| פין 29 | PWM2H — PWM2 high-side output |
| פין 30 | PWM3L — PWM3 low-side output |
| פין 31 | PWM3H — PWM3 high-side output |
| פין 32 | PWM4L — PWM4 low-side output |
| פין 33 | PWM4H — PWM4 high-side output |
| פין 34 | PWM5L — PWM5 low-side output |
| פין 35 | PWM5H — PWM5 high-side output |
| פין 36 | PWM6L — PWM6 low-side output |
| פין 37 | PWM6H — PWM6 high-side output |
| פין 38 | VDD — Digital supply |
| פין 39 | VSS — Digital ground |
| פין 40 | RB0 — Port B bit 0 |
| פין 41 | RB1 — Port B bit 1 |
| פין 42 | RB2 — Port B bit 2 |
| פין 43 | RB3 — Port B bit 3 |
| פין 44 | RB4 — Port B bit 4 |
| פין 45 | RB5 — Port B bit 5 |
| פין 46 | RB6 — Port B bit 6 |
| פין 47 | RB7 — Port B bit 7 |
| פין 48 | RC1 — Port C bit 1 / T1CK |
| פין 49 | RC2 — Port C bit 2 |
| פין 50 | RC3 — Port C bit 3 |
| פין 51 | RC4 — Port C bit 4 |
| פין 52 | RD0 — Port D bit 0 |
| פין 53 | RD1 — Port D bit 1 |
| פין 54 | RD2 — Port D bit 2 |
| פין 55 | RD3 — Port D bit 3 |
| פין 56 | RD4 — Port D bit 4 |
| פין 57 | RD5 — Port D bit 5 |
| פין 58 | RD6 — Port D bit 6 |
| פין 59 | RD8 — Port D bit 8 |
| פין 60 | RD9 — Port D bit 9 |
| פין 61 | RD10 — Port D bit 10 |
| פין 62 | RD11 — Port D bit 11 |
| פין 63 | RD12 — Port D bit 12 |
| פין 64 | RD13 — Port D bit 13 |
| פין 65 | RD14 — Port D bit 14 |
| פין 66 | RD15 — Port D bit 15 |
| פין 67 | RF0 — Port F bit 0 |
| פין 68 | RF1 — Port F bit 1 |
| פין 69 | RF2 — Port F bit 2 |
| פין 70 | RF3 — Port F bit 3 |
| פין 71 | RF4 — Port F bit 4 |
| פין 72 | RF5 — Port F bit 5 |
| פין 73 | RF6 — Port F bit 6 |
| פין 74 | RG0 — Port G bit 0 |
| פין 75 | RG1 — Port G bit 1 |
| פין 76 | RG2 — Port G bit 2 |
| פין 77 | RG3 — Port G bit 3 |
| פין 78 | RG6 — Port G bit 6 |
| פין 79 | RG7 — Port G bit 7 |
| פין 80 | RG8 — Port G bit 8 |
יישומים טיפוסיים
DSPIC30F6013A-30I/PT מתאים עבור 6 יישוםs: Three-Phase BLDC / PMSM Motor Control, Switch-Mode Power Supply (SMPS) Digital Control, Industrial UPS and Inverter Systems, Automotive Body and Chassis Controllers, Audio Effects and Signal Processing, PLC and Industrial Automation Controllers.
Three-Phase BLDC / PMSM Motor Control
The DSPIC30F6013A-30I/PT is purpose-built for three-phase BLDC and PMSM motor control. Its 30 MIPS throughput executes sensorless field-oriented control (FOC) loops with 20 kHz+ PWM frequencies, while the dedicated 8-channel motor-control PWM module with complementary outputs and dead-time insertion drives the inverter directly. The 16-channel 12-bit ADC samples phase currents at the PWM center for back-EMF and current-loop feedback, and the DSP engine handles Park/Clarke transforms and PI control in single-cycle MAC instructions.
מומלץ
Switch-Mode Power Supply (SMPS) Digital Control
In digitally controlled SMPS designs, the DSPIC30F6013A-30I/PT implements PFC, full-bridge phase-shift, or hard-switched PWM control loops at frequencies up to several hundred kHz with the high-resolution PWM module. The DSP engine enables digital average current-mode control and predictive dead-time compensation, while the 12-bit ADC samples inductor current and output voltage. The 132 KB Flash comfortably hosts reference firmware plus application-specific tuning tables for telecom or server PSU designs.
מומלץ
Industrial UPS and Inverter Systems
Uninterruptible power supplies and solar/grid-tie inverters require simultaneous DSP-based waveform generation and MCU-style housekeeping. The DSPIC30F6013A-30I/PT's dual CAN bus interfaces support MODBUS RTU and CANopen industrial networks, while the DSP engine generates pure sine PWM at 50/60 Hz with low THD. The 8 KB EEPROM stores calibration and runtime parameters non-volatilely - critical for solar inverter grid-tie compliance - and the -40C to +85C industrial temperature grade survives harsh cabinet environments.
מומלץ
Automotive Body and Chassis Controllers
Body controllers (BCM), HVAC modules, and chassis subsystems use the DSPIC30F6013A-30I/PT for CAN/LIN gateway logic plus DSP-driven actuator control (stepper motors, brushless fans). The dual CAN modules handle chassis/body CAN buses simultaneously, and the dual UART/SPI/I2C peripherals interface to sensor clusters and display drivers. Note this part is NOT AEC-Q100 qualified - for under-hood AEC-Q100 applications, select the automotive-grade equivalent DSPIC30F6013A-30I/PT family automotive variants.
מומלץ
Audio Effects and Signal Processing
The DSP engine executes real-time audio effects, FIR/IIR filters, FFT spectrum analysis, and active-noise-cancellation kernels with single-cycle MAC throughput. The 12-bit ADC captures audio at 44.1 kSPS per channel with multi-channel multiplexing for beam-forming microphone arrays. The 132 KB Flash holds algorithm lookup tables (window functions, filter coefficients), while the 4 KB SRAM buffers audio frames. Combined with dual I2S-capable SPI interfaces, it forms a compact digital audio processor for consumer amplifiers and hearing-aid development.
מומלץ
PLC and Industrial Automation Controllers
Programmable Logic Controllers (PLCs) and PAC systems leverage the DSPIC30F6013A-30I/PT for PID loop closure on analog process variables (temperature, pressure, flow) at sub-millisecond intervals. The dual CAN interfaces support CANopen DS/CB4xx device profiles, while the UART channels drive RS-485 MODBUS masters. The DSP engine accelerates vibration analysis and predictive maintenance algorithms - critical for Industry 4.0 smart factory retrofits - and the 8 KB EEPROM stores calibration constants for IEC 61131-3 process logic.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DSPIC30F6013A-30I/PT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DSPIC30F6014A-30I/PT | DSPIC30F6012A-30I/PT | DSPIC30F6013A-20I/PT | DSPIC30F6011A-30I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (12x12 mm) | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same |
| CPU Throughput | 30 MIPS | 30 MIPS | 30 MIPS | 20 MIPS | 30 MIPS |
| Flash Memory | 132 KB | 144 KB | 76 KB | 132 KB | 44 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 2 KB |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Drop-in Match | Reference | Yes - upgrade with more Flash | Yes - reduced memory | Yes - same memory, slower | Yes - reduced Flash and peripherals |
מבדילים עיקריים
- Balanced Flash and DSP throughput (לעומתDSPIC30F6012A-30I/PT)
- Higher throughput than 20 MIPS variant (לעומתDSPIC30F6013A-20I/PT)
- Drop-in upgrade path available (לעומתDSPIC30F6014A-30I/PT)
- More memory and peripherals than 6011A (לעומתDSPIC30F6011A-30I/PT)
הערות תכנון
The DSPIC30F6013A-30I/PT requires a clean 5 V (4.5-5.5 V) supply for reliable ADC readings and PWM timing. Place a 10 uF bulk tantalum or ceramic capacitor at each VDD pin pair and a 100 nF ceramic decoupling capacitor within 5 mm of every VDD pin. Add a ferrite bead between the analog AVDD and digital VDD to isolate ADC noise from digital switching transients. Power-on reset (POR) timing requires VDD rise time under 50 ms - if a slow-rising supply is used, hold MCLR low until VDD stabilizes.
The 80-pin TQFP package has theta_JA of approximately 50 C/W on a 2-layer PCB with no thermal vias. At 30 MIPS full CPU load with all peripherals active, internal dissipation is typically 0.5-1 W - well within package ratings. For designs operating at the +85C upper limit, distribute multiple ground pads on the PCB to spread heat and consider minimum 1 oz copper pour on VDD/GND planes.
Route the crystal traces (OSC1/OSC2) symmetrically with a ground guard ring and keep them under 5 mm length. Avoid routing high-current PWM traces under the crystal or near analog inputs. Keep the ICSP clock/data pins (PGEC1/PGED1) accessible for in-circuit programming - do not place capacitors on these lines or programming will fail. The 0.5 mm lead pitch on the 12x12 mm TQFP requires ENIG or OSP surface finish for reliable soldering.
Do not exceed the 5.5 V absolute maximum on any I/O or supply pin - this will latch up the device. Always set configuration fuses (FOSC, FWDT, FPOR) explicitly in source code; do not rely on factory defaults. When migrating between dsPIC30F6012A/6013A/6014A family members, verify the memory map matches - the 6012A has a smaller Flash region and linker scripts must be updated. Brown-out reset must be enabled for reliable field deployment.
Maintain a continuous ground plane under the DSPIC30F6013A-30I/PT to minimize EMI and provide a low-impedance return path for high-speed signals. Place analog input traces away from PWM and digital switching traces - even 10 mm of separation plus a ground keep-out zone dramatically reduces ADC crosstalk. For motor-control designs, place the current-sense amplifiers within 20 mm of the ADC inputs to preserve signal integrity.
מידע על תאימות
RoHS compliant per Microchip product page. Industrial temperature grade (-40C to +85C) but not AEC-Q100 qualified; for automotive applications select AEC-Q100-qualified dsPIC33 family. Halogen-free status not explicitly listed in verified sources.