EFM32G842F64G-E-QFP64 - 32MHz Cortex-M3 64KB MCU | Silicon Labs
MPN: EFM32G842F64G-E-QFP64 ✓ פעילEFM32G842F64G-E-QFP64 סקירה
An energy-efficient microcontroller is a semiconductor that executes embedded control functions while minimizing energy consumption during active operation and idle periods. The EFM32G family belongs to the hierarchy of 32-bit MCU, embedded processor, embedded controller, and semiconductor. This positioning makes the EFM32G842 suitable for portable sensing, industrial control, connected instrumentation, and compact automation products where sleep current and recovery time influence the overall duty cycle.
Three principal specifications define the EFM32G842F64: its 32 MHz Cortex-M3 core, 64 kB Flash allocation for firmware, and 16 kB SRAM for working data. The device also provides 53 digital I/O pins, three 16-bit timers, a 4 x 22 LCD controller, and AES hardware, according to the Silicon Labs product listing and EFM32G family datasheet. These resources support responsive control loops, direct segment or matrix LCD displays, and encrypted communication routines without requiring separate peripheral chips.
The EFM32G low-power platform supports energy-saving operating states and rapid wake-up behavior. The EFM32G family datasheet states that devices can consume as little as 0.6 uA in Stop mode and approximately 180 uA/MHz in Run mode. These figures are important in duty-cycled systems because average system power depends on both active processing time and the duration of the low-power state between measurement or communication events.
Typical uses include portable environmental monitors, compact industrial controllers, low-power sensor nodes, security and access modules, and LCD-equipped measurement instruments. The 64 kB Flash capacity is suitable for moderate embedded applications, while the 53 available I/O pins reduce the need for I/O expanders in designs with sensors, switches, indicators, and display connections.
PCB planning should begin with the manufacturer's 64-pin package drawing and land pattern. Route the 1.98 V to 3.8 V supply through a low-impedance plane, place the recommended bypass capacitors near the power pins, and keep sensitive analog or communication traces away from high-current switching nodes. Confirm the exact pin multiplexing and peripheral assignments against the device datasheet before finalizing the board layout.
This page combines device specifications, family-level drop-in alternatives, application guidance, comparison parameters, and PCB design considerations to support faster component selection and first-board design.
חלופות תחליף ישיר עבור EFM32G842F64G-E-QFP64 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם EFM32G842F64G-E-QFP64 (אותו גורם צורה וטביעת רגל) — שונים ב Digital I/O Pins, Package, Security Feature, Timers.
EFM32G842F64-QFP64
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←EFM32G842F64G-C-QFP64
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
EFM32G842F128G-E-QFP64
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
EFM32G880F128G-E-QFP64
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
EFM32G890F128G-QFP64
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
EFM32G840F64G-QFP64
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
EFM32G842F64G-E-QFP64 דירוגים מרביים ומאפיינים חשמליים
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Series | EFM32 Gecko |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 64 kB |
| Flash Organization | 64K x 8 bits |
| RAM | 16 kB |
| Digital I/O Pins | 53 pins |
| Timers | 3 x 16-bit timers |
| LCD Controller | 4 x 22 LCD segments |
| Security Feature | AES hardware encryption |
| Supply Voltage Range | 1.98 V to 3.8 V |
| מארז | 64-TQFP, 10 x 10 mm |
| מספר פינים | 64 pins |
| סוג הרכבה | Surface mount |
| Family Stop-Mode Current | 0.6 uA |
| Family Run-Mode Current | 180 uA/MHz |
מדריך תצורת פינים של EFM32G842F64G-E-QFP64 64-tqfp, 10 x 10 mm
תצורת פינים עבור EFM32G842F64G-E-QFP64 (מארזת 64-tqfp, 10 x 10 mm). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור EFM32G842F64G-E-QFP64.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
EFM32G842F64G-E-QFP64 מתאים עבור 6 יישוםs: Battery-Powered Environmental Sensor Node, Industrial Control and Automation Module, LCD-Equipped Measurement Instrument, Low-Power IoT Gateway and Controller, Access Control and Security Module, Portable Medical or Wellness Monitor.
Battery-Powered Environmental Sensor Node
The EFM32G842F64G-E-QFP64 fits compact environmental sensors that periodically measure temperature, humidity, gas, or particulate conditions and transmit the results over a low-power serial link. Its 32 MHz Cortex-M3 core provides sufficient control performance, while 64 kB Flash accommodates the acquisition logic and protocol stack and 16 kB RAM supports working buffers. The EFM32G family's Stop-mode current can reach 0.6 uA, allowing the design to remain in a deep sleep state between measurements. Use the low-power wake-up path and duty-cycle scheduling to minimize radio and sensor duty cycles, then verify the complete peripheral configuration in the manufacturer datasheet.
מומלץ
Industrial Control and Automation Module
The EFM32G842F64G-E-QFP64 is suitable for compact PLC-adjacent modules, condition-monitoring controllers, and industrial I/O concentrators that need deterministic control with limited board area. Its 53 digital I/O pins can connect discrete sensors, relay-control logic, status indicators, and industrial interfaces without requiring a large pin-count expansion device. Three 16-bit timers support periodic sampling, input capture, or output timing, and the 1.98 V to 3.8 V range accommodates regulated 3.3 V systems. Keep switching-node current away from sensitive signal paths, provide local bypass capacitance, and validate timing margins against the 32 MHz operating limit.
מומלץ
LCD-Equipped Measurement Instrument
The EFM32G842F64G-E-QFP64 works well in handheld meters, panel instruments, and calibration equipment that combine local measurement control with a display. Its integrated 4 x 22 LCD controller can drive segment-based displays while reducing the need for an external driver, and the 64-TQFP package leaves the perimeter available for switches, a sensor interface, and communication circuitry. The 64 kB Flash supports display and calibration algorithms while 16 kB RAM holds acquisition samples and menu state. Consider resistor sizing and LCD bias requirements from the manufacturer application guidance, and account for the display's idle current when evaluating battery life.
מומלץ
Low-Power IoT Gateway and Controller
The EFM32G842F64G-E-QFP64 can serve as the local controller in an IoT gateway that aggregates sensor inputs, manages a display or keypad, and maintains a low-power serial connection to a remote network. Its 32 MHz Cortex-M3 performance supports protocol handling and event scheduling, while the Gecko energy-saving modes help separate short active bursts from long idle periods. AES hardware is useful for protecting link or application data without occupying the CPU with repetitive encryption tasks. Because low-power performance depends on firmware and peripheral configuration, enable only the required peripherals during sleep and confirm wake sources in the device reference material.
מומלץ
Access Control and Security Module
The EFM32G842F64G-E-QFP64 fits electronic locks, credential readers, and small access-control nodes that require cryptographic support alongside general-purpose control. The integrated AES hardware accelerates symmetric encryption routines, and the 53 available digital I/O pins can serve keypad scanning, indicator control, relay drive, and peripheral status inputs. Its low-power operating characteristics are valuable in battery-backed installations where maintenance access is infrequent. Use a hardware-backed key-management strategy, keep debug access controlled during production, and follow the manufacturer recommendations for supply filtering and decoupling near the security-sensitive device.
מומלץ
Portable Medical or Wellness Monitor
The EFM32G842F64G-E-QFP64 can support compact wellness and diagnostic-adjacent products that sample low-bandwidth sensors and maintain local control logic. The 32 MHz Cortex-M3 core handles sequencing and signal conditioning, while 64 kB Flash accommodates algorithms and 16 kB RAM holds sample histories. Its low-power modes and fast wake-up behavior suit products that must remain responsive without continuously running the processor. For any medical application, validate the complete signal chain, accuracy, safety controls, and regulatory obligations independently; this component specification alone does not establish clinical or diagnostic suitability.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור EFM32G842F64G-E-QFP64 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | EFM32G842F64-QFP64 | EFM32G842F64G-C-QFP64 | EFM32G842F128G-E-QFP64 | EFM32G880F128G-E-QFP64 |
|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) - same footprint | TQFP-64 (10x10 mm) - same footprint | TQFP-64 (10x10 mm) - same footprint | TQFP-64 (10x10 mm) - same footprint |
| CPU Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 64 kB | 64 kB | 64 kB | 128 kB (+100%) | 128 kB (+100%) |
מבדילים עיקריים
- Direct memory and peripheral fit for Gecko designs (לעומתEFM32G842F64-QFP64)
- Memory expansion without changing the board footprint (לעומתEFM32G842F128G-E-QFP64)
- Low-power architecture for duty-cycled products (לעומתEFM32G840F64G-QFP64)
הערות תכנון
Design the supply around the 1.98 V to 3.8 V operating range and place the recommended bypass capacitors directly beside the corresponding power pins. For battery systems, include a regulator whose quiescent current is small relative to the MCU's Stop-mode consumption; otherwise regulator leakage can dominate the sleep budget. Keep analog, digital, and switched-capacitor return paths separated where the pin table permits, and verify the core voltage during startup and low-battery operation.
Use the manufacturer's 64-TQFP 10 x 10 mm land pattern and follow the package drawing for pad dimensions, solder-mask clearance, and copper-defined pads. Place input and output decoupling at the pins rather than at a distant power entry point, and keep the exposed perimeter route free of unnecessary copper if the assembly process requires a defined clearance. Confirm each signal's alternate-function mapping because several 64-pin MCU pads can serve multiple peripheral functions.
Do not treat a same-package 64-TQFP MCU as an automatic cross-brand substitute. Although footprint dimensions match, pin multiplexing, peripheral registers, interrupt priorities, analog characteristics, bootloader behavior, and programming tools can differ. For a redesign, create a pin-to-pin function matrix covering power, ground, reset, debug, clock, communications, and every used GPIO. For an EFM32 family replacement, also update startup code, linker configuration, flash wait-state settings, and peripheral drivers.
Estimated: at a 3.3 V supply and 20 mA average operating current, the estimated device power is 3.3 V x 0.020 A = 0.066 W. This calculation excludes external load power and does not replace the manufacturer's maximum ratings. The resulting junction temperature is normally dominated by PCB copper and ambient conditions rather than the MCU itself, but temperature rise should still be checked when the package is surrounded by heat-generating components or enclosed in a non-ventilated enclosure.
מידע על תאימות
The manufacturer product and datasheet links identify the EFM32G842 as an EFM32 Gecko microcontroller, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated on the cited product page.