INA131AP-1 - Precision Gain-100 Instrumentation Amplifier | TI
MPN: INA131AP-1 ✓ פעילINA131AP-1 סקירה
An instrumentation amplifier is a specialized amplifier that combines differential input handling, high input impedance, accurate gain setting, and strong common-mode rejection into one device. Within the signal-chain hierarchy, it belongs to the amplifier IC family and supports precision measurement, sensor conditioning, and industrial interface systems. Unlike a general-purpose operational amplifier, the INA131AP-1 provides a defined internal gain of 100 and is intended for applications where common-mode noise can overwhelm a small differential measurement.
The INA131AP-1 offers 0.25 uV/°C maximum input offset voltage drift and input overvoltage protection to ±40 V. These characteristics make it suitable for low-level sensor outputs, bridge transducers, current-shunt measurements, and analog front ends where offset and drift affect measurement accuracy. Its 8-pin PDIP package also supports conventional through-hole assembly and prototype boards.
The device uses a three-op-amp instrumentation-amplifier architecture with an internal gain of 100. This architecture provides differential inputs, high input impedance, and balanced amplification while limiting the effect of common-mode voltage. The maximum input bias current of 2 nA is especially relevant when measuring sources with high source impedance, while the 110 dB minimum common-mode rejection helps preserve signal integrity in noisy industrial environments.
Typical uses include bridge-based pressure and load-cell interfaces, current-shunt monitoring in power systems, precision instrumentation, medical equipment, industrial sensor acquisition, and low-level analog signal conditioning. For a 10 mV differential input, the nominal gain of 100 produces an output of 1 V, allowing millivolt-level sensor signals to be measured with standard analog-to-converter input ranges.
Design the input network to limit differential input voltage, maintain source impedance balance, and avoid excessive input bias-current errors. Because the gain is fixed internally, external gain resistors are unnecessary, but the input pins still require careful protection and layout. Check the complete common-mode and output-swing limits against the actual supply voltages rather than relying only on the ±18 V maximum supply rating.
This page combines manufacturer specifications, practical application guidance, comparison parameters, and verified component links. It is designed to help engineers select the part, plan the analog front end, and identify candidate replacements without duplicating the complete manufacturer datasheet.
חלופות תחליף ישיר עבור INA131AP-1 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם INA131AP-1 (אותו גורם צורה וטביעת רגל) — שונים ב Input Bias Current, Package, Amplifier Type, Architecture, Common-Mode Rejection Ratio.
INA131AP
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←INA131BP
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←INA131AP-1 דירוגים מרביים ומאפיינים חשמליים
| Product Type | Precision instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Internal Gain | 100 V/V |
| Architecture | 3-op-amp instrumentation amplifier |
| Input Offset Voltage | 50 uV maximum |
| Input Offset Voltage Drift | 0.25 uV/°C maximum |
| Input Bias Current | 2 nA maximum |
| Common-Mode Rejection Ratio | 110 dB minimum |
| Input Overvoltage Protection | ±40 V |
| Maximum Supply Voltage | ±18 V |
| Total Supply Voltage | 36 V maximum |
| Number of Inputs | 2 differential inputs |
| מספר יציאות | 1 output |
| מארז | 8-pin PDIP |
| סוג הרכבה | Through-hole |
תצורת פינים של INA131AP-1
| פין 1 | RG- — Gain-setting terminal |
| פין 2 | IN- — Inverting input |
| פין 3 | IN+ — Noninverting input |
| פין 4 | V- — Negative supply connection |
| פין 5 | RG+ — Gain-setting terminal |
| פין 6 | OUT — Amplified output |
| פין 7 | V+ — Positive supply connection |
| פין 8 | RG — Gain-setting terminal |
יישומים טיפוסיים
INA131AP-1 מתאים עבור 6 יישוםs: Load-Cell and Pressure-Sensor Front Ends, Current-Shunt Monitoring, Precision Industrial Sensor Acquisition, Low-Level Analog Signal Conditioning, Medical and Laboratory Measurement, Balanced Bridge and Differential Sensing.
Load-Cell and Pressure-Sensor Front Ends
The INA131AP-1 fits low-level bridge measurements because its fixed gain of 100 multiplies a 10 mV differential output to approximately 1 V, while its 110 dB minimum common-mode rejection reduces interference coupled into both sensor inputs. Its 50 uV maximum input offset and 0.25 uV/°C maximum drift help preserve measurement stability over temperature. Place the device close to the bridge and keep the two input paths balanced to minimize thermal gradients and parasitic imbalance. Confirm that bridge excitation, common-mode voltage, and output swing remain within the limits published for the INA131 family before beginning layout.
מומלץ
Current-Shunt Monitoring
INA131AP-1 is appropriate for measuring the small voltage developed across a current shunt when the available analog range is limited. The fixed gain of 100 raises a 10 mV shunt signal to roughly 1 V, while low input bias current of 2 nA limits the disturbance introduced by high-impedance source paths. The 110 dB minimum common-mode rejection is useful when the shunt signal sits on a substantial DC voltage. For best results, use a Kelvin connection to the shunt, keep the two signal traces together, and verify that common-mode and output limits are satisfied over the full current range.
מומלץ
Precision Industrial Sensor Acquisition
The INA131AP-1 supports industrial acquisition circuits that must distinguish small differential sensor outputs from common-mode noise. Its 100 V/V gain, 50 uV maximum offset voltage, and 110 dB minimum common-mode rejection provide useful signal conditioning ahead of an analog-to-converter. Input bias current of 2 nA is suitable for many high-impedance transducers, although source-imbalance errors still require attention. A practical design should place the amplifier near the sensor connector, route the differential pair as a tightly coupled pair, and include protection that does not compromise normal input impedance or common-mode headroom.
מומלץ
Low-Level Analog Signal Conditioning
INA131AP-1 can condition millivolt-level differential signals before further amplification or digitization because its internal gain of 100 removes the need for an external gain network. A 10 mV input becomes approximately 1 V at the output, making the device useful when an ADC cannot accept the original signal directly. The three-op-amp architecture supports differential measurement, while low offset and drift reduce errors that would otherwise be amplified together with the signal. Confirm output headroom, input range, and settling behavior in the manufacturer datasheet, and avoid operating the output near its saturation limits.
מומלץ
Medical and Laboratory Measurement
The INA131AP-1 is suitable for laboratory and medical-instrument signal paths when the required gain is 100 and low offset is important. The 50 uV maximum input offset and 0.25 uV/°C maximum drift help maintain accuracy as temperature changes, while the 110 dB minimum common-mode rejection assists with signals referenced to a nonzero common-mode voltage. Its 8-pin PDIP format is convenient for through-hole prototypes and education platforms. Production medical designs still require application-specific safety, isolation, input-protection, and validation work; the component qualification does not by itself establish compliance for a finished medical system.
מומלץ
Balanced Bridge and Differential Sensing
INA131AP-1 is a natural choice for balanced differential sensing because it is optimized around a gain of 100 and provides 110 dB minimum common-mode rejection. These characteristics help preserve small differential signals when both inputs experience a common disturbance from nearby switching circuits or long cable runs. The low 2 nA maximum input bias current helps when sensor outputs have appreciable impedance, although matched impedances remain important. Use shielded or twisted differential routing, maintain symmetry between input paths, and confirm that the selected power supplies provide sufficient output swing for the required bridge and sensor range.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור INA131AP-1 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | INA131AP | INA131BP |
|---|---|---|---|
| Package | 8-PDIP | 8-PDIP - same | 8-PDIP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Precision instrumentation amplifier | Precision instrumentation amplifier | Precision instrumentation amplifier |
| Internal Gain | 100 V/V | 100 V/V | 100 V/V |
| Architecture | 3-op-amp instrumentation amplifier | 3-op-amp instrumentation amplifier | 3-op-amp instrumentation amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
מבדילים עיקריים
- Fixed precision gain (לעומתINA131AP)
- Low input offset for small-signal measurement (לעומתINA131AP)
- High common-mode rejection (לעומתINA131BP)
הערות תכנון
Route IN+ and IN- as a tightly coupled differential pair, keep both paths over a continuous ground plane, and minimize the distance between the sensor connector and the amplifier. Avoid sharing a return path with high-current switching nodes. Small source-imbalance errors can create differential current and offset, so use equal input impedances and avoid asymmetrical test points, long stubs, and unnecessary series components.
Check the complete input common-mode range and output-voltage range at the actual supply voltage before selecting the power rails. The maximum supply rating is ±18 V, but adequate output headroom is still required when the output approaches a rail. Place a low-noise bypass capacitor close to each supply pin and keep its return path short. Confirm the capacitor voltage rating and effective capacitance at the intended temperature and bias.
Do not assume the ±40 V input overvoltage rating permits unrestricted continuous operation. Verify differential and common-mode limits, confirm whether protection is active only under specified conditions, and use external limiting when fault voltages can exceed the published ratings. Also avoid driving the output into saturation: once clipping occurs, the input offset and recovery behavior can no longer be treated as the normal specified performance.
For cable-connected sensors, use a differential or twisted pair and place suitable input filtering close to the amplifier. Locate protection components where they will not introduce unequal impedance or capacitance between IN+ and IN-. The 110 dB minimum common-mode rejection does not remove the need for balanced routing; mismatched geometry, connectors, and component tolerances can convert common-mode disturbance into differential error before it reaches the amplifier.
מידע על תאימות
No specific environmental or automotive qualification status was established for this ordering code. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the exact INA131AP-1 package and manufacturing configuration before release.