INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments
MPN: INA240A2DR ✓ פעילINA240A2DR סקירה
A current-sense amplifier is a specialized amplifier that measures the voltage developed across a shunt resistor placed in a current-carrying conductor. The INA240 belongs to the current-sense amplifier hierarchy within instrumentation amplifiers and analog signal-chain ICs. It converts the small differential shunt voltage into an amplified voltage proportional to current, supporting both positive and negative current measurement.
The A2 gain code sets the nominal amplification to 50 V/V. Its wide common-mode range permits sensing current above ground, at ground, and down to -4 V, which is useful in systems with inductive flyback or ground-offset returns. Bidirectional operation means that the output can represent positive or negative current without changing the basic shunt arrangement. Enhanced PWM rejection helps suppress switching disturbances commonly encountered in motor-control and power-conversion systems.
The device uses a zero-drift architecture intended to provide accurate current measurement over changing temperatures and time. The manufacturer describes the INA240 family as ultra-precise and optimized for shunt-based measurements. Because the output is proportional to the shunt differential voltage, the shunt resistance determines the conversion between current and amplifier output voltage.
Typical uses include motor and solenoid current monitoring, power-converter feedback, battery current measurement, industrial control systems, and automotive-style PWM systems. The 8-pin SOIC format supports conventional surface-mount assembly and compact analog layouts. Placement close to the shunt helps minimize pickup from adjacent switching nodes.
Designers should verify the complete pin configuration, recommended input filtering, output-voltage range, and absolute maximum ratings in the manufacturer data sheet before layout. Kelvin routing from the shunt terminals and careful grounding are especially important because small differential signals can be corrupted by shared copper impedance or high-current return paths.
This page combines the manufacturer's core INA240 characteristics with exact-MPN commercial information, same-family drop-in options, application guidance, and practical PCB considerations for engineers evaluating the INA240A2DR in a current-measurement design.
חלופות תחליף ישיר עבור INA240A2DR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
INA240A2QDRQ1
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
INA240A2SEP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TSC240
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
INA240A2DR דירוגים מרביים ומאפיינים חשמליים
| Product Type | Bidirectional zero-drift current-sense amplifier |
| Gain | 50 V/V |
| Common-Mode Input Voltage Range | -4 V to 80 V |
| מתח אספקה | 5.5 V |
| סוג פלט | Voltage output |
| Directional Current Sensing | Bidirectional |
| PWM Rejection | Enhanced |
| Amplifier Architecture | Zero-drift |
| Number of Amplifier Channels | 1 channel |
| מארז | 8-pin SOIC |
| Package Body Width | 3.90 mm |
| Package Body Length | 0.154 inch |
| סוג הרכבה | Surface mount |
| Shipping Format | Tape and reel |
מדריך תצורת פינים של INA240A2DR 0.154 inch
תצורת פינים עבור INA240A2DR (מארזת 0.154 inch). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור INA240A2DR.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
INA240A2DR מתאים עבור 6 יישוםs: Motor PWM Current Monitoring, Solenoid and Flyback Sensing, DC-DC Converter Current Feedback, Battery Pack Current Measurement, Industrial Power Supply Protection, Three-Phase Inverter Shunt Sensing.
Motor PWM Current Monitoring
The INA240A2DR fits motor-control current feedback because its -4 V to 80 V common-mode range accommodates shunt positions in systems where the switching node rises well above the 5.5 V amplifier supply. Bidirectional sensing captures both motoring and regenerative current, while enhanced PWM rejection helps preserve measurement accuracy during switching transitions. Place the amplifier close to the shunt and route the differential inputs as a Kelvin pair to minimize high-current copper drops and switching-node pickup.
מומלץ
Solenoid and Flyback Sensing
The INA240A2DR is suitable for measuring current through an inductive load because its common-mode input range extends from -4 V to 80 V, including the negative transient region associated with typical solenoid flyback. The fixed 50 V/V gain converts the shunt differential voltage into a proportional analog signal with sufficient headroom for control and protection circuitry. Designers must still verify transient energy, input filtering, supply sequencing, and the output behavior during saturation.
מומלץ
DC-DC Converter Current Feedback
In a DC-DC converter, the INA240A2DR can monitor inductor or shunt current while the -4 V to 80 V common-mode range covers power rails above the 5.5 V device supply. Bidirectional measurement is useful in converters that reverse current or operate in four-quadrant control, and the zero-drift architecture targets stable low-level current measurement. Compensation and protection loops should account for amplifier delay, output saturation, shunt tolerance, and the timing relationship between the sensed current and the converter duty cycle.
מומלץ
Battery Pack Current Measurement
The INA240A2DR can measure charge and discharge current in a battery pack because its bidirectional operation reports both polarities and its common-mode range is independent of the 5.5 V supply. The 50 V/V gain is useful when the selected shunt produces a small differential signal. In a multi-cell pack, protection and measurement limits must be evaluated against the full battery voltage, while shunt placement should avoid current-sharing paths that would corrupt the measurement.
מומלץ
Industrial Power Supply Protection
The INA240A2DR supports fast power-supply current monitoring and overcurrent detection in industrial equipment by converting a shunt voltage into a proportional analog signal. Its common-mode range covers high-side sensing above the 5.5 V supply, and bidirectional operation can identify reverse-current conditions as well as normal forward load current. The protection threshold, response time, output range, and system fault behavior should be evaluated together so that saturation does not delay a required shutdown action.
מומלץ
Three-Phase Inverter Shunt Sensing
The INA240A2DR can be placed across a low-side or ground-referenced inverter shunt when the sensed common-mode voltage remains within its -4 V to 80 V range. Bidirectional measurement supports positive and negative phase currents, while enhanced PWM rejection improves signal quality in switching power stages. Layout quality is critical: the differential pair should connect directly to the shunt pads, the return current should avoid the input path, and filtering should be selected without introducing excessive response delay.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור INA240A2DR — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | INA240A2QDRQ1 | INA240A2SEP | TSC240 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | Bidirectional zero-drift current-sense amplifier | Bidirectional current-sense amplifier | Bidirectional current-sense amplifier | Current-sense amplifier |
| Gain | 50 V/V | 50 V/V | 50 V/V | 50 V/V |
| Common-Mode Input Range | -4 V to 80 V | -4 V to 80 V | -4 V to 80 V | Wider common-mode range |
מבדילים עיקריים
- Wide common-mode sensing range (לעומתTSC240)
- Bidirectional PWM-rejecting measurement (לעומתTSC240)
- Automotive-qualified same-family option (לעומתINA240A2DR)
הערות תכנון
Route the INA240A2DR differential inputs directly from the shunt pads as a compact, matched pair. Keep the amplifier and input traces away from switching nodes, inductors, and high-current return paths. Connect the returned ground reference at the amplifier side of the shunt rather than allowing input current to flow through sensitive copper.
Do not infer the exact 8-pin pinout from the SOIC package alone. Use the manufacturer INA240 data sheet to assign power, ground, input, and output pins, including any exposed or no-connect conditions. A wrong connection can bypass the differential sensing path or expose the inputs to an unintended common-mode voltage.
Filter the differential inputs only after accounting for the amplifier's bandwidth and control-loop requirements. Excessive filtering can delay current protection, while insufficient filtering can allow PWM edges to disturb the measurement. Validate the selected network with the actual shunt impedance, trace geometry, switching frequency, and the INA240 response characteristics.
Estimated: use P = (5.5 V - VOUT) × IOUTPUT plus internal quiescent dissipation to estimate amplifier loss, then compare the resulting junction temperature with the manufacturer limit. The inputs used are supply voltage, output voltage, and maximum output current. Actual performance also depends on SOIC copper area, ambient temperature, and airflow, so include the PCB thermal path in the calculation.
מידע על תאימות
The standard INA240A2DR orderable part is not identified as an AEC-Q100-qualified variant. INA240A2QDRQ1 is the automotive-qualified same-family option. Compliance status for the standard part requires confirmation in the manufacturer product documentation.