Texas Instruments

INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI

MPN: INA333SJD ✓ פעיל
1.8 V to 5.5 V Vdss 2 nA Id 8-pin SOIC-8 (JD) Package
כמות הזמנה מינימלית: 1 |

INA333SJD סקירה

Texas Instruments INA333SJD is a low-power, zero-drift, rail-to-rail-output instrumentation amplifier packaged in an 8-pin SOIC-8 (JD) package. Its headline characteristics include a 1.8 V to 5.5 V supply range, 150 kHz gain-bandwidth product, 10 µV offset voltage, and 2 nA input bias current. The device is intended for precision low-level sensor measurements where low offset, low drift, high common-mode rejection, and low input bias current are more important than wide bandwidth.

An instrumentation amplifier is a differential-input amplifier designed to amplify a small voltage difference between two inputs while rejecting common-mode voltage. The INA333 belongs to the broader zero-drift amplifier family, combining an instrumentation-amplifier architecture with chopper-stabilized low-offset behavior. A zero-drift amplifier continuously corrects its own offset error, allowing low input-referred offset to remain stable over time and temperature.

The INA333SJD supports gains of 1, 10, 100, and 1000 through its RG pin. Manufacturer specifications identify a maximum offset voltage of 25 µV at a gain of 100, offset drift of 0.2 µV/°C at a gain of 1000, input noise of 55 nV/√Hz at a gain of 100, and minimum common-mode rejection of 100 dB at a gain of 10. Its 0.16 V/µs slew rate supports relatively slow sensor signals without requiring a high-speed amplifier.

The rail-to-rail output allows the output voltage to approach the supply rails, improving usable signal range in low-voltage systems. Gain is established by a single external resistor on the RG pin, simplifying circuit implementation while keeping the gain-setting component outside the amplifier. The measured gain error also depends on the tolerance and temperature coefficient of that resistor, so precision applications should use a suitable resistor network.

Typical uses include bridge-based pressure and strain measurements, low-current sensors, biomedical instrumentation, industrial process monitoring, and portable sensor systems. The device is particularly useful when sensor output is small, common-mode voltage is substantial, and thermal offset variation would otherwise dominate the measurement.

The principal design trade-off is bandwidth versus precision: the INA333 prioritizes low offset and low drift, while its 150 kHz gain-bandwidth product is modest compared with general-purpose high-speed amplifiers. Designers should also evaluate the high-temperature variant indicated by the INA333SJD ordering information and verify the complete electrical limits for the intended operating range.

This product page consolidates the verified manufacturer and distributor details, identifies the practical benefits of zero-drift operation, and organizes the device's gains, noise, offset, supply, package, and application constraints for faster engineering selection.

חלופות תחליף ישיר עבור INA333SJD — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם INA333SJD (אותו גורם צורה וטביעת רגל) — שונים ב Operating Temperature Range, Package, Slew Rate.

Texas Instruments
Operating Temperature Range: -40 C to +125 C
Package: 8-pin VSSOP (DGK)
Slew Rate: 0.16 V/us
השווה עם INA333SJD →

INA333D

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 SOIC-8
Uses the same 8-pin SOIC-8 footprint and zero-drift instrumentation-amplifier architecture; INA333SJD extends the temperature range to 210 °C while INA333D is limited to the standard INA333 temperature rating.

📋 חלופה להתייחסות (לא בקטלוג)

INA333AIDGKR

✅ Drop-In ⚠️ מפרטים לא מאומתים
Texas Instruments
📦 SOIC-8
Precision zero-drift instrumentation amplifier · 3-operational-amplifier · 1 channel · 1.8 V to 5.5 V · 50 uA typical · 10 uV typical · 1 to 1000 · G = 1 + 100 kΩ/RG

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

INA333SJD דירוגים מרביים ומאפיינים חשמליים

Amplifier Type Instrumentation amplifier
Number of Circuits 1 circuit
Supply Voltage Range 1.8 V to 5.5 V
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 150 kHz
Slew Rate 0.16 V/µs
Offset Voltage 10 µV
Maximum Offset Voltage at Gain 100 25 µV
Offset Drift at Gain 1000 0.2 µV/°C
Input Noise at Gain 100 55 nV/√Hz
Minimum CMRR at Gain 10 100 dB
Input Bias Current 2 nA
סוג פלט Rail-to-rail output
טווח טמפרטורת פעולה -55 °C to 210 °C
מארז 8-pin SOIC-8 (JD)
סוג הרכבה Surface mount
Packaging Tube

תצורת פינים של INA333SJD

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
פין 1 R- — Inverting input and gain-setting resistor connection
פין 2 IN- — Inverting input
פין 3 IN+ — Noninverting input
פין 4 V- — Negative supply connection
פין 5 REF — Reference input
פין 6 OUT — Output voltage
פין 7 V+ — Positive supply connection
פין 8 RG — Gain-setting resistor connection

יישומים טיפוסיים

INA333SJD מתאים עבור 6 יישוםs: Strain-Gauge Bridge Measurements, Pressure and Load-Cell Signal Chains, Battery-Powered Sensor Interfaces, Biomedical and Diagnostic Instrumentation, Low-Current and Electrochemical Sensors, Industrial Process and Condition Monitoring.

🏭

Strain-Gauge Bridge Measurements

The INA333SJD is appropriate for resistive strain-gauge bridges because it combines low input bias current, low offset voltage, and high common-mode rejection in a compact 8-pin package. A bridge output is typically a small differential signal superimposed on a substantial excitation-centered common-mode voltage; the amplifier's 100 dB minimum CMRR at gain 10 helps reject that common-mode component. With a 3.3 V or 5 V supply and a suitable RG resistor, the rail-to-rail output provides more usable range than a fixed-headroom amplifier. The zero-drift architecture also helps maintain measurement stability as temperature changes, although gain error from the external resistor must be included in the system budget.

⚖️

Pressure and Load-Cell Signal Chains

The INA333SJD can amplify low-level differential outputs from piezoresistive pressure sensors, load cells, and force transducers. Its 10 µV offset rating and 2 nA input bias current are important when the transducer has high source impedance or produces millivolt-level full-scale signals. The 0.16 V/µs slew rate is appropriate for slow-to-moderate mechanical events and industrial monitoring signals rather than high-frequency dynamic loading. For a bridge supplied from 5 V, the amplifier's 1.8 V to 5.5 V operating range supports the rail-to-rail output architecture, but the design must verify common-mode input limits, settling behavior, and the exact gain accuracy.

📱

Battery-Powered Sensor Interfaces

The INA333SJD fits portable and battery-operated sensor systems that require accurate differential measurement at low supply voltage. Operation begins at 1.8 V, allowing the amplifier to operate alongside low-voltage sensors, analog-to-digital converters, and microcontrollers. Its micro-power design reduces the impact of continuous amplification on battery capacity, while the rail-to-rail output helps the signal approach the available supply range. For duty-cycled acquisition systems, verify settling time for the selected gain and confirm that the signal source's common-mode voltage remains within the device's electrical limits. A bypass capacitor near the supply pins should follow the manufacturer layout guidance.

💊

Biomedical and Diagnostic Instrumentation

The INA333SJD is suitable for low-amplitude biomedical front ends such as ECG, EMG, plethysmography, and bioimpedance measurement blocks when the system operates within its specified electrical and environmental limits. The low input bias current helps prevent loading of high-impedance skin electrodes, while the low offset and zero-drift characteristics reduce baseline movement over time. The rail-to-rail output allows a compact analog front end to operate from a low-voltage supply and connect directly to an ADC. Safety-critical or patient-connected designs require separate review of isolation, leakage current, input protection, applied-part limits, and medical regulatory obligations beyond the amplifier's electrical specifications.

🧪

Low-Current and Electrochemical Sensors

The INA333SJD can serve as the precision input stage for electrochemical, gas, conductivity, and other sensors that generate small differential signals. Its 2 nA input bias current reduces the error generated when the sensor source impedance is high, while the 55 nV/√Hz noise specification at gain 100 establishes a useful baseline for many slow chemical-sensing systems. The instrumentation-amplifier topology simplifies differential excitation and sensing arrangements, although sensor-specific guarding, reference grounding, and polarity conventions still require careful review. The 150 kHz gain-bandwidth product is more than adequate for many concentration measurements but should be checked against transient response requirements in fast-flow or rapidly changing sensor systems.

📡

Industrial Process and Condition Monitoring

The INA333SJD is useful in industrial process-monitoring equipment that measures thermocouple-like, bridge, or other low-level differential signals. The extended -55 °C to 210 °C ordering range makes it relevant to equipment operating across a broad environmental envelope, while its high common-mode rejection supports sensing in electrically noisy systems. The zero-drift architecture reduces time-dependent offset errors during long measurement cycles, which is valuable in stable process control. Designers should still place input filtering and ESD protection appropriately, keep sensitive traces away from switching nodes, and validate accuracy over the complete temperature range. The external RG resistor and reference network must also be reviewed for tolerance and thermal drift.

What is the INA333SJD?
The INA333SJD is a Texas Instruments single-circuit, micro-power, zero-drift instrumentation amplifier with rail-to-rail output. It operates from 1.8 V to 5.5 V and is offered in an 8-pin SOIC-8 (JD) package. According to the Texas Instruments product page, the part is associated with a high-temperature operating range of -55 °C to 210 °C, making it suitable for precision signal chains that require low offset and enhanced thermal coverage.
What are the key specifications of INA333SJD that engineers should know?
The INA333SJD combines a 1.8 V to 5.5 V supply range, 150 kHz gain-bandwidth product, 10 µV offset voltage, 2 nA input bias current, and 0.16 V/µs slew rate. The manufacturer listing also identifies rail-to-rail output, 25 µV maximum offset at gain 100, 0.2 µV/°C drift at gain 1000, 55 nV/√Hz noise at gain 100, and 100 dB minimum CMRR at gain 10.
Where can I download the INA333SJD datasheet PDF?
The INA333SJD datasheet can be obtained from the Texas Instruments product page or the manufacturer's INA333-HT datasheet entry linked on this page. The manufacturer document covers the micro-power, zero-drift, rail-to-rail-output instrumentation amplifier and its high-temperature ordering options. Use the pin-description table and electrical-characteristics tables for final PCB assignments, gain calculations, and worst-case design checks.
Where can I find the INA333SJD pinout?
The INA333SJD uses an 8-pin SOIC-8 layout with two differential inputs, supply pins, an output, a reference input, and an external gain-setting resistor connection. Use the manufacturer pin-description table when assigning PCB tracks, especially for RG and REF. Because the package is a surface-mount SOIC-8, verify land pattern, pin-one orientation, and assembly clearances against the latest board design.
How is the gain set on the INA333SJD?
The INA333SJD uses a single external resistor on the RG pin to establish gain, with practical selections of 1, 10, 100, and 1000. The resistor sets the differential gain while the internal amplifier network performs the gain-setting action. According to the Texas Instruments INA333 documentation, component tolerance and temperature drift affect total gain accuracy, so the resistor should be selected according to the required measurement accuracy.
Why is the INA333SJD suited to precision sensor measurements?
The INA333SJD is suited to precision sensor measurements because its zero-drift architecture minimizes input-referred offset movement. Manufacturer specifications identify a 10 µV offset voltage, 2 nA input bias current, 55 nV/√Hz noise at gain 100, and 100 dB minimum common-mode rejection at gain 10. These characteristics are valuable for strain gauges, bridge sensors, low-current detectors, and other signals buried in a larger common-mode voltage.
What is the difference between INA333SJD and INA333D?
The INA333SJD is the high-temperature SOIC-8 ordering option, while INA333D is the standard 8-pin SOIC-8 ordering option in the same amplifier family. Their functional architecture remains based on a micro-power, zero-drift instrumentation amplifier with rail-to-rail output. The primary selection distinction is operating-temperature coverage: INA333SJD extends to 210 °C, whereas the standard INA333D should be selected only within its own specified temperature limits.
When should I choose INA333SJD over INA333D?
Choose INA333SJD when the circuit must operate above the standard INA333D temperature range or when high-temperature qualification is a design requirement. The INA333SJD is identified by Texas Instruments as a high-temperature version with operation from -55 °C to 210 °C. For ordinary room-temperature industrial or laboratory measurements within the standard part's limits, INA333D may be sufficient, but the complete operating range should be checked before substitution.
Is INA333SJD the same as INA333D?
The INA333SJD and INA333D are not identical across every environmental condition. Both belong to the INA333 instrumentation-amplifier family and use an 8-pin SOIC-8 package, but INA333SJD provides the extended high-temperature coverage of -55 °C to 210 °C. A PCB-level swap is practical where the full operating envelope, reliability requirements, and purchasing constraints allow the INA333SJD configuration.
What can replace INA333SJD?
The closest same-family SOIC-8 replacement is the standard INA333D, because it uses the same instrumentation-amplifier architecture and 8-pin package format. It is a drop-in option only when the circuit remains within the INA333D temperature limits and the replacement's complete electrical ratings are acceptable. For designs operating above the standard device's range, retain INA333SJD or qualify another high-temperature part separately.
Is there a Texas Instruments equivalent for INA333SJD?
Texas Instruments INA333D is the closest standard family alternative with an 8-pin SOIC-8 package and the same micro-power, zero-drift instrumentation-amplifier function. The meaningful distinction is environmental: INA333SJD provides operation from -55 °C to 210 °C. Confirm gain error, offset, noise, common-mode rejection, supply range, and temperature limits against the application before treating the standard part as a replacement.
Where can I buy INA333SJD online?
Use the Request a Quote form on this page to request INA333SJD availability, current commercial terms, and the appropriate tube packaging quantity. The form provides a direct path for a purchase inquiry without relying on changing third-party inventory status. Include the target quantity, acceptable delivery date, and whether a manufacturer-authorized traceability or quality document is required.
What is the price of INA333SJD?
The current commercial price for INA333SJD is obtained through the Request a Quote form on this page. The structured quote request lets the supplier match the exact 8-pin SOIC-8 ordering code, tube packaging requirement, quantity, and any traceability or delivery conditions. Request a refreshed quote before budgeting because component pricing and availability can change without notice.
What is the lead time for INA333SJD?
Request the current INA333SJD lead time and minimum order quantity through the Request a Quote form on this page. Include your required shipment date, annual usage, and acceptable tube packaging quantity in the request. This avoids relying on a generic inventory estimate and allows the supplier to confirm whether new supply, manufacturer-authorized channels, or another sourcing route best matches the schedule.
Is INA333SJD in stock?
Current INA333SJD stock should be confirmed through the Request a Quote form on this page rather than inferred from a product listing. State the required quantity and target delivery date in the request so the supplier can return a current availability commitment. The device is specified in tube packaging, and any available quantity should be confirmed against that packaging requirement.
Does INA333SJD need special thermal design?
The INA333SJD requires normal copper-based thermal design attention, especially near its extended upper temperature limit. Its SOIC-8 package and low-power operating approach limit heat generation, but actual junction temperature depends on supply voltage, output loading, ambient temperature, PCB copper, and nearby heat sources. Use the manufacturer power-dissipation and thermal-resistance guidance to verify the worst-case operating condition rather than relying on package type alone.

נתוני עזר הנדסיים עבור INA333SJD — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose INA333SJD when the measurement system needs the INA333 family's low-offset, low-drift instrumentation-amplifier performance and must also operate across an extended -55 °C to 210 °C range. Its 1.8 V to 5.5 V supply capability, 2 nA input bias current, 150 kHz gain-bandwidth product, and rail-to-rail output are well suited to low-level sensors, strain bridges, pressure transducers, and industrial monitoring circuits. Choose INA333D when the circuit stays within the standard family member's temperature range and equivalent electrical performance is acceptable. Consider INA333AID when an automotive-qualified family option is required, but verify that its qualification and operating-temperature envelope match the complete system requirement. For any substitution, confirm the pin arrangement, gain-setting method, reference behavior, common-mode range, output swing, and maximum supply voltage against the manufacturer datasheet.

השוואה עם חלופות

פרמטר מוצר זה INA333D INA333AID
Brand Texas Instruments Texas Instruments Texas Instruments
Package SOIC-8 (JD) SOIC-8 - same package SOIC-8 - same package
Amplifier Type Micro-power zero-drift instrumentation amplifier Zero-drift instrumentation amplifier Zero-drift instrumentation amplifier
Output Type Rail-to-rail output Rail-to-rail output Rail-to-rail output

מבדילים עיקריים

  • Extended high-temperature operating range (לעומתINA333D)
  • Low-offset precision architecture (לעומתINA333AID)
  • Low-voltage operation with rail-to-rail output (לעומתINA333D)

הערות תכנון

Place the RG resistor close to pin 8 and keep the associated input and supply traces short and quiet. Connect the input bypass capacitor directly between the supply pins and ground, and route REF to a low-impedance reference network only when an offset adjustment is required. Maintain a continuous ground path beneath the sensitive input section, and avoid routing input traces beneath switching-regulator power stages, inductors, or high-current return paths.

Treat the INA333SJD as a precision, relatively low-bandwidth amplifier rather than a general-purpose 150 kHz signal-chain device. Select the external RG resistor for the required gain, then include its tolerance and temperature coefficient in the total gain-error budget. For fast common-mode or input transients, verify the input common-mode range, output settling behavior, and filtering requirements; excessive input capacitance can also affect settling and stability at higher gains.

At elevated ambient temperatures, calculate worst-case dissipation from the actual supply voltage, output voltage, load current, and quiescent current, then add it to the effect of external heat sources. Use the manufacturer's thermal characterization for the SOIC-8 footprint and actual PCB copper rather than treating the listed operating-temperature limit as a guarantee for every layout. Provide copper spreading around the package and avoid placing the amplifier directly above a hot controller or power stage.

Do not allow the differential input signal or common-mode input voltage to exceed the electrical limits, even when the output remains within its rail-to-rail range. Grounding REF to ground is appropriate only for a ground-referenced output; tying it to an inappropriate supply rail can move the output outside the sensor's usable range. Also account for input bias-current error across high source impedances and ensure that the chosen gain remains compatible with the available output swing.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The manufacturer product and distributor listings do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements for this ordering code. Compliance fields remain unknown rather than inferred from the manufacturer name or family designation.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

INA333SJD datasheet INA333SJD pinout INA333SJD datasheet pdf INA333SJD specifications INA333SJD equivalent INA333SJD replacement INA333SJD price INA333SJD stock Texas Instruments INA333SJD INA333SJD SOIC-8 pinout INA333SJD zero drift amplifier INA333SJD instrumentation amplifier application INA333SJD vs INA333D

רכיבים ומונחים קשורים

Texas Instruments INA333SJD INA333D INA333AID instrumentation amplifier zero-drift amplifier precision amplifier micro-power amplifier differential input amplifier rail-to-rail output common-mode rejection ratio CMRR input bias current input-referred offset offset drift gain-bandwidth product slew rate bridge sensor strain gauge pressure transducer bioimpedance measurement SOIC-8 JD package surface-mount package
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר