ISL26708IHZ-T7A - 8-Bit 1MSPS SAR ADC | Renesas | SOT-23-8
MPN: ISL26708IHZ-T7A ✓ פעילISL26708IHZ-T7A סקירה
A SAR ADC is a type of analog-to-digital converter that uses a binary-search algorithm through an internal capacitive DAC to successively approximate the input voltage against a precision reference. SAR ADCs offer the best combination of throughput, latency, and power consumption for multiplexed data acquisition, motor control, and instrumentation front-ends where a single conversion result must be captured per trigger without the pipeline delay of higher-speed architectures.
Key features of the ISL26708IHZ-T7A include 1 MSPS minimum throughput, no missing codes at 8-bit resolution, low power consumption (approximately 8.5 mW at 1 MSPS with 5V supply), a SPI/QSPI/MICROWIRE-compatible serial interface, and a true-differential analog input that supports ±VREF common-mode. An external reference voltage (1V to 5V) sets the input full-scale range, giving designers flexibility to optimize dynamic range.
The robust input structure, wide supply tolerance, and small SOT-23-8 footprint make the ISL26708IHZ-T7A well-suited for portable instrumentation, industrial process control loops, sensor signal conditioning, and battery-monitoring front-ends. Its differential input rejects common-mode noise present in long sensor cable runs.
When designing with this device, place the 0.1 uF and 10 uF decoupling capacitors as close as possible to the AVDD and DVDD pins to ensure conversion accuracy, and route the analog and digital ground returns to a single-point star ground near the ADC's GND pin to avoid digital switching noise coupling into the analog input.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
חלופות תחליף ישיר עבור ISL26708IHZ-T7A — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ISL26708IHZ-T7A (אותו גורם צורה וטביעת רגל) — שונים ב Input Type, Package, Resolution, RoHS Status, Sampling Rate.
ISL26710IHZ-T7A
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
ISL26712IHZ-T7A
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ISL26708IHZ-T7A דירוגים מרביים ומאפיינים חשמליים
| רזולוציה | 8 bits |
| קצב דגימה | 1 MSPS (minimum) |
| Architecture | SAR (Successive Approximation Register) |
| Number of Channels | 1 (single-ended or pseudo-differential) |
| Analog Supply Voltage (AVDD) | 2.7 V to 5.25 V |
| Digital Supply Voltage (DVDD) | 2.7 V to 5.25 V |
| Input Type | Fully-differential (true bipolar capable) |
| מתח ייחוס | External, 1 V to AVDD |
| Power Consumption | 8.5 mW typical at 1 MSPS (5V supply) |
| Digital Interface | SPI / QSPI / MICROWIRE-compatible serial |
| טמפרטורת פעולה | -40C to +85C (Industrial) |
| מארז | 8-pin SOT-23 (IHZ) |
| סוג הרכבה | Surface Mount |
| סטטוס RoHS | Compliant |
| Lead-Free | Yes |
| נטול הלוגנים | Yes |
תצורת פינים של ISL26708IHZ-T7A
| פין 1 | AVDD — Analog supply voltage (2.7V to 5.25V) |
| פין 2 | REF — External reference voltage input |
| פין 3 | IN+ — Positive differential analog input |
| פין 4 | IN- — Negative differential analog input |
| פין 5 | GND — Ground |
| פין 6 | SDO — Serial data output |
| פין 7 | SCLK — Serial clock input |
| פין 8 | CNVT — Conversion start / active-low chip select |
יישומים טיפוסיים
ISL26708IHZ-T7A מתאים עבור 6 יישוםs: Industrial Process Control Sensor Front-End, Battery Management Monitoring, Portable Instrumentation Data Acquisition, Motor Control Current Sensing, Audio Signal Digitization, IoT Sensor Node ADC.
Industrial Process Control Sensor Front-End
The ISL26708IHZ-T7A's fully-differential input rejects common-mode noise present on long sensor cable runs in factory environments, while its 1 MSPS throughput supports fast process-control loop times. The device operates from 2.7V to 5.25V, accepting either 3.3V or 5V sensor rails. The wide industrial -40C to +85C temperature range and 8-bit resolution are appropriate for monitoring strain-gauge bridges, thermocouples, and 4-20 mA loop receivers where high dynamic range is unnecessary but reliable conversion is essential.
מומלץ
Battery Management Monitoring
The ISL26708IHZ-T7A's low power consumption of 8.5 mW at 1 MSPS makes it suitable for battery-cell voltage monitoring in multi-cell battery packs. The differential input tolerates ground-shift noise between stacked cells, and the SPI-compatible serial interface requires only 3 microcontroller GPIO pins. The 8-bit resolution provides 20 mV steps on a 5V reference, sufficient for battery state-of-charge estimation in consumer and light-industrial battery management systems.
מומלץ
Portable Instrumentation Data Acquisition
The ISL26708IHZ-T7A's small SOT-23-8 footprint and low 8.5 mW power dissipation make it ideal for handheld multimeters, portable oscilloscopes, and field-test instruments. The 1 MSPS throughput enables capture of audio-bandwidth and low-RF signals, while the differential input rejects hum pickup on probe leads. An external 2.5V or 5V reference can be selected to trade input range for absolute accuracy depending on the measurement being made.
מומלץ
Motor Control Current Sensing
In brushless-DC and stepper motor drives, the ISL26708IHZ-T7A digitizes shunt-resistor voltage drops with 1 MSPS throughput for current-loop control. The differential input accepts the bipolar voltage across a low-side or high-side shunt, and the fast conversion rate supports PWM frequencies up to 50 kHz with 20 samples per PWM cycle. The SOT-23-8 package allows placement close to the shunt resistor for noise immunity.
מומלץ
Audio Signal Digitization
The ISL26708IHZ-T7A's 1 MSPS sampling rate supports audio-bandwidth digitization up to 40 kHz with Nyquist-compliant sampling. The 8-bit resolution is sufficient for voice-band applications, simple audio mixers, and consumer audio effects. The differential input accepts line-level audio signals directly when paired with a 2.5V reference, eliminating the need for an external instrumentation amplifier in cost-sensitive designs.
מומלץ
IoT Sensor Node ADC
The ISL26708IHZ-T7A's serial SPI interface and small SOT-23-8 footprint suit it to space-constrained IoT sensor nodes reading temperature, light, or gas-sensor analog outputs. Power-down current between conversions drops the consumption to microamp levels, enabling battery lifetimes of years on coin cells. The 8-bit resolution is adequate for threshold-based alerts and coarse measurements where the MCU performs additional digital filtering.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ISL26708IHZ-T7A — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ISL26710IHZ-T7A | ISL26712IHZ-T7A |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | SOT-23-8 | SOT-23-8 - same | SOT-23-8 - same |
| Resolution | 8 bits | 10 bits | 12 bits |
| Sampling Rate | 1 MSPS | 1 MSPS | 1 MSPS |
| Architecture | SAR | SAR | SAR |
| Input Type | Fully differential | Fully differential | Fully differential |
| Supply Voltage | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C |
| Pin-to-Pin Compatible | Yes (this part) | Yes | Yes |
מבדילים עיקריים
- True fully-differential input (לעומתSingle-ended SAR ADCs in SOT-23 packages)
- Family-compatible upgrade path (לעומתFixed-resolution 8-bit competitor ADCs)
- Wide 2.7V to 5.25V supply range (לעומת3.3V-only competitor ADCs)
הערות תכנון
Place a 0.1 uF ceramic decoupling capacitor as close as possible to the AVDD pin (pin 1), with a 10 uF tantalum or ceramic bulk capacitor within a few millimeters. The DVDD pin typically shares the same supply but benefits from its own 0.1 uF bypass cap to isolate digital switching noise from the analog supply. Star-ground the analog and digital returns to the GND pin (pin 5) to prevent digital return currents from flowing through the analog ground reference.
Route the differential analog inputs (IN+ and IN-, pins 3 and 4) as a matched-length, matched-impedance pair to preserve common-mode rejection at high frequencies. Keep the analog input traces away from the serial interface lines (SDO, SCLK, CNVT) and from switching power converters. Place the external reference decoupling capacitor (typically 10 uF) directly at the REF pin (pin 2) with a short, low-inductance trace to GND.
Do not leave the CNVT pin (pin 8) floating - it must be driven high or low by the host microcontroller. Failing to fully decouple AVDD will result in degraded INL/DNL and reduced SNR. The external reference voltage (REF) sets the input full-scale range: VFS = 2 x VREF for differential inputs. Exceeding VREF + 0.3V on the analog inputs will damage the device. The serial clock SCLK should not exceed 20 MHz.
מידע על תאימות
RoHS and REACH compliant per Renesas product page. Industrial temperature grade -40C to +85C. Not AEC-Q100 qualified - choose a Q1 suffix variant for automotive applications if available.
