Renesas Electronics

ISL83488IP - 3.3V 250kbps Full-Duplex RS-485 Transceiver | Renesas

MPN: ISL83488IP ✓ פעיל
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin PDIP (8-PDIP) Package
כמות הזמנה מינימלית: 1 |

ISL83488IP סקירה

Renesas Electronics ISL83488IP is a 3.3 V, full-duplex RS-485 and RS-422 transceiver operating at up to 250 kbps. It uses a slew-rate-limited BiCMOS output stage and is packaged in an 8-pin plastic dual in-line package identified by the IP suffix. The device provides separate receiver inputs and transmitter outputs for balanced point-to-point communication.

A differential line transceiver is the interface between a logic-level controller and a balanced, noise-resistant communications bus. The ISL83488IP combines a transmit channel, receive channel, bus driver, and differential receiver in one package. RS-485 is commonly used for longer, multipoint industrial networks, while RS-422 is generally associated with dedicated driver and receiver connections. Slew-rate limiting reduces edge speed and electromagnetic interference, making this device especially useful where 250 kbps is sufficient.

The principal operating characteristics are a 3.3 V power requirement, a maximum signaling rate of 250 kbps, full-duplex operation, and support for both RS-485 and RS-422 interfaces. Separate transmit and receive paths allow the node to send and receive simultaneously. The 8-PDIP format supports conventional through-hole PCB layouts, prototyping, and repair of legacy industrial equipment where a surface-mount package would be inconvenient.

Because the transmitter edges are deliberately slew-rate limited, the ISL83488IP favors controlled bus transitions and reduced high-frequency EMI over maximum data throughput. This characteristic makes it suitable for point-to-point RS-422 links, industrial instrumentation, factory equipment, and low-to-moderate-speed RS-485 networks. Designers should still preserve the recommended termination and fail-safe biasing network around the balanced bus.

Typical uses include isolated and non-isolated industrial control links, sensor interfaces, data acquisition systems, motor controllers, and communications between test equipment and peripheral modules. The full-duplex configuration avoids sharing a driver and receiver on the same pair, which simplifies bus topology in point-to-point designs. In a multipoint RS-485 installation, however, only one driver should be active at a time, and the receiver must tolerate an inactive or shorted bus.

For PCB implementation, route the balanced pair together, keep the transceiver close to the connector, and provide a solid ground reference. Decoupling capacitors should connect directly to the supply and ground pins, while surge protection should be placed near the external connector. Verify that cable length, termination, node count, and grounding remain compatible with the intended RS-485 or RS-422 topology.

This product page combines the manufacturer specification, verified package and interface characteristics, compatible family context, practical layout guidance, and a structured replacement comparison. It is intended to help engineers identify the correct electrical function, package, data rate, and board-level integration requirements before committing the ISL83488IP to a new or legacy design.

חלופות תחליף ישיר עבור ISL83488IP — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם ISL83488IP (אותו גורם צורה וטביעת רגל) — שונים ב Product Type, Duplex Mode, Maximum Data Rate, Package, Package Type.

Renesas Electronics
Product Type: RS-485/RS-422 transceiver
Duplex Mode: Half duplex
Maximum Data Rate: 10 Mbps
השווה עם ISL83488IP →
Renesas Electronics
Product Type: RS-485/RS-422 transceiver IC
Package Type: 8-DIP, through hole
השווה עם ISL83488IP →
Renesas Electronics
Product Type: 1/1 RS-485/RS-422 transceiver
Package Type: 14-pin PDIP
השווה עם ISL83488IP →

ISL83483IP

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 8-PDIP
Half-duplex multiplexed receive and transmit pins instead of the ISL83488IP full-duplex configuration; data rate remains 250 kbps

📋 חלופה להתייחסות (לא בקטלוג)

ISL83485IP

✅ Drop-In ⚠️ מפרטים לא מאומתים
Renesas Electronics
📦 8-PDIP
RS-485/RS-422 transceiver · 1 driver / 1 receiver · Half duplex · 3.3 V · 10 Mbps · RS-485 and RS-422 · BiCMOS · Low power

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

ISL83490IP

✅ Drop-In ⚠️ מפרטים לא מאומתים
Renesas Electronics
📦 8-PDIP
RS-485/RS-422 transceiver IC · 1 driver · 1 receiver · Full duplex · RS-485 and RS-422 · 3 V to 3.6 V · 3.3 V · Low power

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

ISL83491IP

✅ Drop-In ⚠️ מפרטים לא מאומתים
Renesas Electronics
📦 8-PDIP
1/1 RS-485/RS-422 transceiver · 3 V to 3.6 V · 3.3 V · RS-485 and RS-422 · 1 driver · 1 receiver · BiCMOS · High-speed or slew-rate-limited

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

ISL83488IBZ

✅ Drop-In
📦 8-LD
Same 3.3 V, 250 kbps full-duplex RS-485 and RS-422 function but a surface-mount package instead of through-hole 8-PDIP

📋 חלופה להתייחסות (לא בקטלוג)

ISL83488IP מפרטים

מתח אספקה 3.3 V
Maximum Data Rate 250 kbps
Interface Standards RS-485 and RS-422
Duplex Mode Full duplex
Transceiver Configuration 1 transmitter and 1 receiver
Logic Technology BiCMOS
Output Slew Rate Slew-rate limited
מארז 8-pin PDIP (8-PDIP)
סוג הרכבה Through-hole
טמפרטורת פעולה -40 C to +85 C
Manufacturer Renesas Electronics
Product Family ISL83483, ISL83485, ISL83488, ISL83490, ISL83491

מדריך תצורת פינים של ISL83488IP 8-pin pdip (8-pdip)

תצורת פינים עבור ISL83488IP (מארזת 8-pin pdip (8-pdip)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 8-pin pdip (8-pdip) עבור ISL83488IP

אין נתוני פריסת פינים מפורטים עבור ISL83488IP.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

ISL83488IP מתאים עבור 6 יישוםs: Industrial Sensor Networks, Point-to-Point RS-422 Equipment Links, Factory Automation Control Links, Data Acquisition and Instrumentation, Motor and Power Controller Communication, Legacy Equipment Repair and Retrofit.

🏭

Industrial Sensor Networks

The ISL83488IP suits balanced sensor links that must operate from a 3.3 V rail at rates up to 250 kbps. Its full-duplex arrangement permits simultaneous command transmission and measurement return, while the slew-rate-limited driver reduces the severity of fast edge transitions on industrial cabling. Install termination and biasing at the appropriate points in the bus, and route the balanced pair together from the transceiver to the connector. The principal benefit is controlled signaling without requiring a separate driver for each direction.

🌐

Point-to-Point RS-422 Equipment Links

For point-to-point RS-422 equipment links, the ISL83488IP provides separate transmit and receive channels at up to 250 kbps from a 3.3 V supply. Full-duplex operation avoids sharing a driver and receiver, simplifying cable and termination planning for dedicated links. Its controlled output transitions are advantageous where EMI-sensitive equipment uses long or imperfect cables. The design should still implement the source and destination terminations specified by the RS-422 system configuration.

🏭

Factory Automation Control Links

The ISL83488IP can connect a controller to remote automation equipment over a balanced RS-485 or RS-422 link running at up to 250 kbps. The full-duplex configuration supports simultaneous command and status traffic, and the 3.3 V supply simplifies integration with modern control electronics. Its slew-rate-limited driver helps limit EMI from cable transitions. Engineers should validate node count, cable length, grounding, and protection against the industrial surge environment before production release.

📡

Data Acquisition and Instrumentation

Data acquisition modules can use the ISL83488IP for a reliable balanced connection between measurement electronics and a host controller. The 250 kbps rate is suitable for many multiplexed sensor and status channels, while full-duplex operation allows commands and data to coexist on separate conductor pairs. The 8-PDIP package is convenient for instrument prototypes and repairable industrial hardware. Keep the transceiver near the connector and provide local supply decoupling to preserve signal integrity at the interface boundary.

⚡

Motor and Power Controller Communication

The ISL83488IP provides a low-speed balanced command path between a motor controller and supervisory electronics at rates up to 250 kbps. Its 3.3 V operation suits compact control boards, and the controlled driver transitions reduce high-frequency EMI that could interfere with nearby power circuitry. The full-duplex arrangement allows operating commands and fault feedback to be exchanged concurrently. Validate grounding and isolation strategy carefully when the transceiver shares a high-current power stage.

🔧

Legacy Equipment Repair and Retrofit

The 8-PDIP package makes the ISL83488IP especially useful for repairing or retrofitting legacy equipment that used through-hole interface ICs. It provides a modern 3.3 V RS-485 and RS-422 function at up to 250 kbps without requiring a surface-mount footprint redesign. Full-duplex operation can simplify replacement of older communication subsystems when the external pin arrangement is compatible. Confirm every net against the family datasheet because related family members can use different duplex and disable configurations.

What is the Renesas ISL83488IP?
The ISL83488IP is a 3.3 V, full-duplex RS-485 and RS-422 transceiver with a maximum data rate of 250 kbps. According to the Renesas product page, it is a single BiCMOS transceiver with separate transmit and receive paths, a slew-rate-limited output, and an 8-pin PDIP package. It is intended for balanced industrial communications where controlled edge rates and low EMI are more important than high-speed operation.
What is the operating voltage of ISL83488IP?
The ISL83488IP operates from a 3.3 V power supply. The Renesas manufacturer page identifies the device as a 3.3 V-powered BiCMOS transceiver supporting RS-485 and RS-422 signaling at rates up to 250 kbps. Because this is a single-supply device, system designs should provide a stable 3.3 V rail and place the required decoupling capacitance close to the supply and ground pins.
What is the maximum data rate of ISL83488IP?
The ISL83488IP supports signaling rates up to 250 kbps. The manufacturer describes it as a slew-rate-limited, full-duplex transceiver for both RS-485 and RS-422. This rate is appropriate for slow industrial control links, sensor networks, point-to-point equipment connections, and legacy systems where reducing edge speed helps limit EMI and ringing on long or imperfect cables.
Is ISL83488IP full duplex or half duplex?
The ISL83488IP is configured for full-duplex operation, with separate receiver inputs and transmitter outputs. Renesas identifies the ISL83488 as part of its family of full-duplex transceivers, while related ISL83483 and ISL83485 products use half-duplex multiplexing. Full-duplex operation allows simultaneous transmission and reception, simplifying point-to-point RS-422 and full-duplex RS-485 layouts.
Which package does ISL83488IP use?
The ISL83488IP is supplied in an 8-pin plastic dual in-line package, also listed as 8-PDIP. The IP suffix distinguishes this through-hole package from the ISL83488IBZ surface-mount option. The package is suited to conventional through-hole assembly, repair, and industrial products that do not require a small SMD footprint. Consult the manufacturer pin-description table before assigning PCB nets.
Where can I download the ISL83488IP datasheet PDF?
The ISL83488IP datasheet can be obtained from Renesas through the ISL83483, ISL83485, ISL83488, ISL83490, ISL83491 family datasheet page linked on this product page. The document covers the device family, including electrical characteristics, pin descriptions, interface behavior, and application information. The Renesas ISL83488 product page is also the appropriate starting point for current lifecycle and ordering information.
Where can I find the ISL83488IP pinout?
The ISL83488IP pinout is documented in the pin-description table of the Renesas ISL83483, ISL83485, ISL83488, ISL83490, ISL83491 family datasheet. The IP variant uses an 8-pin PDIP with separate full-duplex receive and transmit connections. Use that table for the exact terminal numbering, especially when distinguishing driver inputs, driver outputs, receiver inputs, enables, power, and ground.
Where can I buy ISL83488IP online?
The ISL83488IP can be requested through the Request a Quote form on this XAIPART page. The form is the appropriate channel for current availability, volume pricing, lead time, and exact package confirmation. The device is identified as an 8-PDIP, 3.3 V, 250 kbps full-duplex RS-485 and RS-422 transceiver, so include that MPN and package suffix in the request.
What is the price of ISL83488IP?
Current pricing for ISL83488IP should be obtained through the Request a Quote form on this page. The form supports volume, delivery, and lifecycle questions without presenting a potentially stale fixed figure. Quote requests should identify the exact 8-PDIP suffix ISL83488IP, the required quantity, and the shipment destination so the commercial response reflects the correct package and order quantity.
What is the lead time for ISL83488IP?
The current lead time for ISL83488IP depends on order quantity, scheduled delivery, and the confirmed supply status of the exact 8-PDIP package. Submit the required quantity and target date through the Request a Quote form on this page. Renesas lists the ISL83488 family on its manufacturer product page, and the quotation response should confirm the delivery commitment for ISL83488IP.
Is ISL83488IP in stock?
Current ISL83488IP stock status should be confirmed through the Request a Quote form on this page. The form allows the requested quantity, packaging, and delivery location to be included in the availability response. Do not infer stock from a catalog listing alone; request confirmation for the exact ISL83488IP 8-PDIP order code before committing a production schedule.
What can replace ISL83488IP?
A drop-in replacement for ISL83488IP must use the same 8-pin PDIP footprint, provide separate full-duplex transmit and receive paths, operate from 3.3 V, and support compatible RS-485 and RS-422 signaling at 250 kbps or less. Renesas family members can have different half- or full-duplex configurations, so the family name alone does not establish pin compatibility. Use the family datasheet and the Request a Quote form to identify an approved sourcing option.
ISL83488IP vs ISL83490IP - which is better for an RS-422 link?
Both devices belong to Renesas's 8-pin full-duplex transceiver family and operate at 250 kbps, but their driver and receiver-control arrangements differ. The ISL83488 is the general RS-485 and RS-422 full-duplex option, while the ISL83490 is a related full-duplex variant with different output-disable behavior. For a point-to-point RS-422 link without the unused disable functions, the ISL83488IP may be preferable because those controls are unnecessary.
When should I choose ISL83488IP over another RS-485 transceiver?
Choose ISL83488IP when a design needs a 3.3 V, 250 kbps, full-duplex RS-485 or RS-422 interface and an 8-PDIP package is acceptable. Its separate receive and transmit paths suit point-to-point balanced links, while slew-rate limiting prioritizes controlled transitions and reduced EMI. Choose a different transceiver when the system requires a surface-mount package, a much higher data rate, half-duplex multiplexing, or isolated communication.
Is ISL83488IP suitable for industrial equipment?
The ISL83488IP is suitable for industrial communications that operate within its stated -40 C to +85 C temperature range and require RS-485 or RS-422 at up to 250 kbps. Its 250 kbps slew-rate-limited design is appropriate for many control and instrumentation links. The 8-PDIP package also simplifies through-hole assembly and repair. Final qualification should include the enclosure temperature, cable length, surge environment, and grounding arrangement.
What are the key specifications of ISL83488IP that engineers should know?
The key ISL83488IP specifications are a 3.3 V supply, 250 kbps maximum data rate, full-duplex operation, RS-485 and RS-422 support, slew-rate-limited BiCMOS circuitry, an 8-PDIP package, and a -40 C to +85 C operating range. The manufacturer describes one transceiver with separate receiver inputs and transmitter outputs. These characteristics make the device suitable for balanced point-to-point links and lower-speed industrial networks.
What is the best equivalent for ISL83488IP?
The best equivalent for ISL83488IP is the device that preserves its 8-PDIP footprint, 3.3 V operation, full-duplex topology, separate RS-485 and RS-422 channels, and 250 kbps class of data rate. Renesas family variants are the closest starting point, but half-duplex members and packages such as ISL83488IBZ are not direct substitutes. Request a quote for the exact ISL83488IP or have a candidate cross-reference checked against the family pin-description table.

נתוני עזר הנדסיים עבור ISL83488IP — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose ISL83488IP for a 3.3 V, 250 kbps, full-duplex RS-485 or RS-422 interface when an 8-PDIP package is required. It is particularly suitable for point-to-point links, industrial instrumentation, sensor links, and repair of legacy equipment where through-hole assembly is preferable and controlled output transitions help limit EMI. Select ISL83483IP or ISL83485IP only when a half-duplex shared-bus architecture is acceptable and their exact pin assignments match the design. Choose ISL83490IP or ISL83491IP when the additional disable-control behavior is useful. ISL83488IBZ provides the same 3.3 V, 250 kbps full-duplex function in a surface-mount 8-LD package, but it is not a board-level drop-in replacement for an existing ISL83488IP footprint. For every proposed substitution, verify the manufacturer pin table, termination requirements, enable logic, operating temperature, and bus topology.

השוואה עם חלופות

פרמטר מוצר זה ISL83483IP ISL83485IP ISL83490IP ISL83491IP ISL83488IBZ
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-LD
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps
Duplex Configuration Full duplex Half duplex Half duplex Full duplex Full duplex Full duplex
Interface Standards RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422
Output Edge Control Slew-rate limited Slew-rate limited Slew-rate limited Slew-rate limited Slew-rate limited Slew-rate limited
Operating Temperature -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C
Transmitter and Receiver Disable Controls Not applicable to applications not requiring Rx and Tx output disable functions Half-duplex multiplexed configuration Half-duplex multiplexed configuration Includes full-duplex output-disable arrangement Includes full-duplex output-disable arrangement Same functional configuration as ISL83488

מבדילים עיקריים

  • Separate full-duplex communication paths (לעומתISL83483IP)
  • Through-hole package preserves existing leaded PCB layouts (לעומתISL83488IBZ)
  • Simplified full-duplex configuration for point-to-point links (לעומתISL83490IP)

הערות תכנון

Place the ISL83488IP close to the external communication connector and route the balanced pair as a tightly coupled differential pair. Connect supply-decoupling capacitors directly between the device power pin and ground, with the shortest possible return path. Keep the driver outputs and receiver inputs away from switching nodes and high-current power-stage traces to minimize differential noise pickup and ground bounce.

Apply termination according to the selected RS-485 or RS-422 topology rather than adding it indiscriminately at every node. For point-to-point RS-422, terminate the driver end and remote receiver end as specified by the system architecture. For RS-485, use termination at the physical ends of the bus and provide biasing only at one designated location when fail-safe operation is required.

The ISL83488IP is slew-rate limited, so its output transitions are already controlled for lower EMI. Preserve that advantage by keeping stub lengths short, avoiding unnecessary test pads on the balanced lines, and maintaining a continuous ground reference beneath and alongside the cable route. Place surge or other protection at the connector boundary rather than far downstream, where its capacitance could degrade signal quality.

Do not interchange the ISL83488 with half-duplex family members without reviewing the complete pin descriptions. The ISL83488 uses separate receive and transmit paths, while ISL83483 and ISL83485 multiplex those functions. Also do not substitute the ISL83488IBZ on an existing through-hole PCB because the 8-LD surface-mount package requires a different footprint and assembly process.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The manufacturer identifies the ISL83488 as a 3.3 V, 250 kbps, full-duplex RS-485 and RS-422 BiCMOS transceiver. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified, so those fields remain unknown.

חיפושים קשורים

ISL83488IP datasheet ISL83488IP pinout ISL83488IP datasheet pdf ISL83488IP equivalent ISL83488IP replacement ISL83488IP 8-PDIP ISL83488IP RS-422 transceiver ISL83488IP price Renesas ISL83488IP ISL83488IP vs ISL83488IBZ ISL83488 250kbps transceiver ISL83488 application circuit

רכיבים ומונחים קשורים

Renesas Electronics ISL83488IP ISL83488 ISL83483IP ISL83485IP ISL83490IP ISL83491IP ISL83488IBZ RS-485 RS-422 differential transceiver full-duplex communications half-duplex communications BiCMOS slew-rate-limited driver 250 kbps 3.3 V power supply 8-PDIP 8-LD balanced differential line industrial control sensor interface electromagnetic interference termination resistor fail-safe biasing
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר